From ee52b188ca2c631427d197056ab7b71b9e23bde7 Mon Sep 17 00:00:00 2001 From: York Sun Date: Thu, 11 Oct 2012 07:13:37 +0000 Subject: powerpc/t4qds: Add T4QDS board MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The T4240QDS is a high-performance computing evaluation, development and test platform supporting the T4240 QorIQ Power Architecture™ processor. SERDES Connections 32 lanes grouped into four 8-lane banks Two “front side” banks dedicated to Ethernet Two “back side” banks dedicated to other protocols DDR Controllers Three independant 64-bit DDR3 controllers Supports rates up to 2133 MHz data-rate Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller QIXIS System Logic FPGA Each DDR controller has two DIMM slots. The first slot of each controller has up to 4 chip selects to support single-, dual- and quad-rank DIMMs. The second slot has only 2 chip selects to support single- and dual-rank DIMMs. At any given time, up to total 4 chip selects can be used. Detail information can be found in doc/README.t4qds Signed-off-by: York Sun Signed-off-by: Andy Fleming Signed-off-by: Kumar Gala Signed-off-by: Prabhakar Kushwaha Signed-off-by: Shengzhou Liu Signed-off-by: Roy Zang Signed-off-by: Andy Fleming --- board/freescale/t4qds/Makefile | 54 ++++ board/freescale/t4qds/ddr.c | 186 +++++++++++++ board/freescale/t4qds/eth.c | 495 +++++++++++++++++++++++++++++++++ board/freescale/t4qds/law.c | 47 ++++ board/freescale/t4qds/pci.c | 39 +++ board/freescale/t4qds/t4240qds_qixis.h | 56 ++++ board/freescale/t4qds/t4qds.c | 395 ++++++++++++++++++++++++++ board/freescale/t4qds/t4qds.h | 37 +++ board/freescale/t4qds/tlb.c | 136 +++++++++ 9 files changed, 1445 insertions(+) create mode 100644 board/freescale/t4qds/Makefile create mode 100644 board/freescale/t4qds/ddr.c create mode 100644 board/freescale/t4qds/eth.c create mode 100644 board/freescale/t4qds/law.c create mode 100644 board/freescale/t4qds/pci.c create mode 100644 board/freescale/t4qds/t4240qds_qixis.h create mode 100644 board/freescale/t4qds/t4qds.c create mode 100644 board/freescale/t4qds/t4qds.h create mode 100644 board/freescale/t4qds/tlb.c (limited to 'board/freescale/t4qds') diff --git a/board/freescale/t4qds/Makefile b/board/freescale/t4qds/Makefile new file mode 100644 index 0000000000..ff09ffa51e --- /dev/null +++ b/board/freescale/t4qds/Makefile @@ -0,0 +1,54 @@ +# +# Copyright 2012 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-$(CONFIG_T4240QDS)+= eth.o +COBJS-$(CONFIG_PCI) += pci.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/t4qds/ddr.c b/board/freescale/t4qds/ddr.c new file mode 100644 index 0000000000..692616aed4 --- /dev/null +++ b/board/freescale/t4qds/ddr.c @@ -0,0 +1,186 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * Version 2 or later as published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +struct board_specific_parameters { + u32 n_ranks; + u32 datarate_mhz_high; + u32 clk_adjust; + u32 wrlvl_start; + u32 wrlvl_ctl_2; + u32 wrlvl_ctl_3; + u32 cpo; + u32 write_data_delay; + u32 force_2T; +}; + +/* + * This table contains all valid speeds we want to override with board + * specific parameters. datarate_mhz_high values need to be in ascending order + * for each n_ranks group. + */ +static const struct board_specific_parameters udimm0[] = { + /* + * memory controller 0 + * num| hi| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz|adjst| start | ctl2 | ctl3 | |delay | + */ + {2, 1350, 5, 7, 0x0809090b, 0x0c0c0d09, 0xff, 2, 0}, + {2, 1666, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, + {2, 2140, 5, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {1, 1350, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {1, 1700, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, + {1, 1900, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0}, + {1, 2140, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {} +}; + +/* + * The three slots have slightly different timing. The center values are good + * for all slots. We use identical speed tables for them. In future use, if + * DIMMs require separated tables, make more entries as needed. + */ +static const struct board_specific_parameters *udimms[] = { + udimm0, +}; + +static const struct board_specific_parameters rdimm0[] = { + /* + * memory controller 0 + * num| hi| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T + * ranks| mhz|adjst| start | ctl2 | ctl3 | |delay | + */ + {4, 1350, 5, 9, 0x08070605, 0x07080805, 0xff, 2, 0}, + {4, 1666, 5, 8, 0x08070605, 0x07080805, 0xff, 2, 0}, + {4, 2140, 5, 8, 0x08070605, 0x07081805, 0xff, 2, 0}, + {2, 1350, 5, 7, 0x0809090b, 0x0c0c0d09, 0xff, 2, 0}, + {2, 1666, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, + {2, 2140, 5, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {1, 1350, 5, 8, 0x0809090b, 0x0c0c0d0a, 0xff, 2, 0}, + {1, 1700, 5, 8, 0x080a0a0c, 0x0c0d0e0a, 0xff, 2, 0}, + {1, 1900, 4, 8, 0x080a0a0c, 0x0e0e0f0a, 0xff, 2, 0}, + {1, 2140, 4, 8, 0x090a0b0c, 0x0e0f100b, 0xff, 2, 0}, + {} +}; + +/* + * The three slots have slightly different timing. See comments above. + */ +static const struct board_specific_parameters *rdimms[] = { + rdimm0, +}; + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL; + ulong ddr_freq; + + if (ctrl_num > 2) { + printf("Not supported controller number %d\n", ctrl_num); + return; + } + if (!pdimm->n_ranks) + return; + + /* + * we use identical timing for all slots. If needed, change the code + * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num]; + */ + if (popts->registered_dimm_en) + pbsp = rdimms[0]; + else + pbsp = udimms[0]; + + + /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr + * freqency and n_banks specified in board_specific_parameters table. + */ + ddr_freq = get_ddr_freq(0) / 1000000; + while (pbsp->datarate_mhz_high) { + if (pbsp->n_ranks == pdimm->n_ranks) { + if (ddr_freq <= pbsp->datarate_mhz_high) { + popts->cpo_override = pbsp->cpo; + popts->write_data_delay = + pbsp->write_data_delay; + popts->clk_adjust = pbsp->clk_adjust; + popts->wrlvl_start = pbsp->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twoT_en = pbsp->force_2T; + goto found; + } + pbsp_highest = pbsp; + } + pbsp++; + } + + if (pbsp_highest) { + printf("Error: board specific timing not found " + "for data rate %lu MT/s\n" + "Trying to use the highest speed (%u) parameters\n", + ddr_freq, pbsp_highest->datarate_mhz_high); + popts->cpo_override = pbsp_highest->cpo; + popts->write_data_delay = pbsp_highest->write_data_delay; + popts->clk_adjust = pbsp_highest->clk_adjust; + popts->wrlvl_start = pbsp_highest->wrlvl_start; + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2; + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3; + popts->twoT_en = pbsp_highest->force_2T; + } else { + panic("DIMM is not supported by this board"); + } +found: + /* + * Factors to consider for half-strength driver enable: + * - number of DIMMs installed + */ + popts->half_strength_driver_enable = 0; + /* + * Write leveling override + */ + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + + /* + * Rtt and Rtt_WR override + */ + popts->rtt_override = 0; + + /* Enable ZQ calibration */ + popts->zq_en = 1; + + /* DHC_EN =1, ODT = 75 Ohm */ + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm); + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm); +} + +phys_size_t initdram(int board_type) +{ + phys_size_t dram_size; + + puts("Initializing....using SPD\n"); + + dram_size = fsl_ddr_sdram(); + + dram_size = setup_ddr_tlbs(dram_size / 0x100000); + dram_size *= 0x100000; + + puts(" DDR: "); + return dram_size; +} diff --git a/board/freescale/t4qds/eth.c b/board/freescale/t4qds/eth.c new file mode 100644 index 0000000000..a49c7d4f15 --- /dev/null +++ b/board/freescale/t4qds/eth.c @@ -0,0 +1,495 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "../common/qixis.h" +#include "../common/fman.h" + +#include "t4240qds_qixis.h" + +#define EMI_NONE 0xFFFFFFFF +#define EMI1_RGMII 0 +#define EMI1_SLOT1 1 +#define EMI1_SLOT2 2 +#define EMI1_SLOT3 3 +#define EMI1_SLOT4 4 +#define EMI1_SLOT5 5 +#define EMI1_SLOT7 7 +#define EMI2 8 /* tmp, FIXME */ +/* Slot6 and Slot8 do not have EMI connections */ + +static int mdio_mux[NUM_FM_PORTS]; + +static const char *mdio_names[] = { + "T4240QDS_MDIO0", + "T4240QDS_MDIO1", + "T4240QDS_MDIO2", + "T4240QDS_MDIO3", + "T4240QDS_MDIO4", + "T4240QDS_MDIO5", + "NULL", + "T4240QDS_MDIO7", + "T4240QDS_10GC", +}; + +static u8 lane_to_slot_fsm1[] = {1, 1, 1, 1, 2, 2, 2, 2}; +static u8 lane_to_slot_fsm2[] = {3, 3, 3, 3, 4, 4, 4, 4}; + +static const char *t4240qds_mdio_name_for_muxval(u8 muxval) +{ + return mdio_names[muxval]; +} + +struct mii_dev *mii_dev_for_muxval(u8 muxval) +{ + struct mii_dev *bus; + const char *name = t4240qds_mdio_name_for_muxval(muxval); + + if (!name) { + printf("No bus for muxval %x\n", muxval); + return NULL; + } + + bus = miiphy_get_dev_by_name(name); + + if (!bus) { + printf("No bus by name %s\n", name); + return NULL; + } + + return bus; +} + +struct t4240qds_mdio { + u8 muxval; + struct mii_dev *realbus; +}; + +static void t4240qds_mux_mdio(u8 muxval) +{ + u8 brdcfg4; + if ((muxval < 6) || (muxval == 7)) { + brdcfg4 = QIXIS_READ(brdcfg[4]); + brdcfg4 &= ~BRDCFG4_EMISEL_MASK; + brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT); + QIXIS_WRITE(brdcfg[4], brdcfg4); + } +} + +static int t4240qds_mdio_read(struct mii_dev *bus, int addr, int devad, + int regnum) +{ + struct t4240qds_mdio *priv = bus->priv; + + t4240qds_mux_mdio(priv->muxval); + + return priv->realbus->read(priv->realbus, addr, devad, regnum); +} + +static int t4240qds_mdio_write(struct mii_dev *bus, int addr, int devad, + int regnum, u16 value) +{ + struct t4240qds_mdio *priv = bus->priv; + + t4240qds_mux_mdio(priv->muxval); + + return priv->realbus->write(priv->realbus, addr, devad, regnum, value); +} + +static int t4240qds_mdio_reset(struct mii_dev *bus) +{ + struct t4240qds_mdio *priv = bus->priv; + + return priv->realbus->reset(priv->realbus); +} + +static int t4240qds_mdio_init(char *realbusname, u8 muxval) +{ + struct t4240qds_mdio *pmdio; + struct mii_dev *bus = mdio_alloc(); + + if (!bus) { + printf("Failed to allocate T4240QDS MDIO bus\n"); + return -1; + } + + pmdio = malloc(sizeof(*pmdio)); + if (!pmdio) { + printf("Failed to allocate T4240QDS private data\n"); + free(bus); + return -1; + } + + bus->read = t4240qds_mdio_read; + bus->write = t4240qds_mdio_write; + bus->reset = t4240qds_mdio_reset; + sprintf(bus->name, t4240qds_mdio_name_for_muxval(muxval)); + + pmdio->realbus = miiphy_get_dev_by_name(realbusname); + + if (!pmdio->realbus) { + printf("No bus with name %s\n", realbusname); + free(bus); + free(pmdio); + return -1; + } + + pmdio->muxval = muxval; + bus->priv = pmdio; + + return mdio_register(bus); +} + +void board_ft_fman_fixup_port(void *blob, char * prop, phys_addr_t pa, + enum fm_port port, int offset) +{ + if (mdio_mux[port] == EMI1_RGMII) + fdt_set_phy_handle(blob, prop, pa, "phy_rgmii"); + + /* TODO: will do with dts */ +} + +void fdt_fixup_board_enet(void *fdt) +{ + /* TODO: will do with dts */ +} + +int board_eth_init(bd_t *bis) +{ +#if defined(CONFIG_FMAN_ENET) + int i; + struct memac_mdio_info dtsec_mdio_info; + struct memac_mdio_info tgec_mdio_info; + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_prtcl_s1, srds_prtcl_s2; + + srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + + /* Initialize the mdio_mux array so we can recognize empty elements */ + for (i = 0; i < NUM_FM_PORTS; i++) + mdio_mux[i] = EMI_NONE; + + dtsec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM2_DTSEC_MDIO_ADDR; + + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fm_memac_mdio_init(bis, &dtsec_mdio_info); + + tgec_mdio_info.regs = + (struct memac_mdio_controller *)CONFIG_SYS_FM2_TGEC_MDIO_ADDR; + tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME; + + /* Register the 10G MDIO bus */ + fm_memac_mdio_init(bis, &tgec_mdio_info); + + /* Register the muxing front-ends to the MDIO buses */ + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII); + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1); + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2); + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3); + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4); + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5); + t4240qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT7); + t4240qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2); + + + switch (srds_prtcl_s1) { + case 1: + case 2: + case 4: + /* XAUI/HiGig in Slot1 and Slot2 */ + fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR); + fm_info_set_phy_address(FM1_10GEC2, FM1_10GEC2_PHY_ADDR); + break; + case 28: + case 36: + /* SGMII in Slot1 and Slot2 */ + fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR); + if ((srds_prtcl_s2 != 56) && (srds_prtcl_s2 != 57)) { + fm_info_set_phy_address(FM1_DTSEC9, + SGMII_CARD_PORT4_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC10, + SGMII_CARD_PORT3_PHY_ADDR); + } + break; + case 38: + fm_info_set_phy_address(FM1_DTSEC5, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, QSGMII_CARD_PHY_ADDR); + if ((srds_prtcl_s2 != 56) && (srds_prtcl_s2 != 57)) { + fm_info_set_phy_address(FM1_DTSEC9, + QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC10, + QSGMII_CARD_PHY_ADDR); + } + break; + case 40: + case 46: + case 48: + fm_info_set_phy_address(FM1_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR); + if ((srds_prtcl_s2 != 56) && (srds_prtcl_s2 != 57)) { + fm_info_set_phy_address(FM1_DTSEC10, + SGMII_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC9, + SGMII_CARD_PORT4_PHY_ADDR); + } + fm_info_set_phy_address(FM1_DTSEC1, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC3, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC4, QSGMII_CARD_PHY_ADDR); + break; + default: + puts("Invalid SerDes1 protocol for T4240QDS\n"); + break; + } + + for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) { + int idx = i - FM1_DTSEC1, lane, slot; + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_SGMII: + lane = serdes_get_first_lane(FSL_SRDS_1, + SGMII_FM1_DTSEC1 + idx); + if (lane < 0) + break; + slot = lane_to_slot_fsm1[lane]; + debug("FM1@DTSEC%u expects SGMII in slot %u\n", + idx + 1, slot); + if (QIXIS_READ(present2) & (1 << (slot - 1))) + fm_disable_port(i); + switch (slot) { + case 1: + mdio_mux[i] = EMI1_SLOT1; + fm_info_set_mdio(i, + mii_dev_for_muxval(mdio_mux[i])); + break; + case 2: + mdio_mux[i] = EMI1_SLOT2; + fm_info_set_mdio(i, + mii_dev_for_muxval(mdio_mux[i])); + break; + }; + break; + case PHY_INTERFACE_MODE_RGMII: + /* FM1 DTSEC5 routes to RGMII with EC2 */ + debug("FM1@DTSEC%u is RGMII at address %u\n", + idx + 1, 2); + if (i == FM1_DTSEC5) + fm_info_set_phy_address(i, 2); + mdio_mux[i] = EMI1_RGMII; + fm_info_set_mdio(i, + mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } + + for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + mdio_mux[i] = EMI2; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } + + +#if (CONFIG_SYS_NUM_FMAN == 2) + switch (srds_prtcl_s2) { + case 1: + case 2: + case 4: + /* XAUI/HiGig in Slot3 and Slot4 */ + fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR); + fm_info_set_phy_address(FM2_10GEC2, FM2_10GEC2_PHY_ADDR); + break; + case 7: + case 13: + case 14: + case 16: + case 22: + case 23: + case 25: + case 26: + /* XAUI/HiGig in Slot3, SGMII in Slot4 */ + fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR); + break; + case 28: + case 36: + /* SGMII in Slot3 and Slot4 */ + fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC9, SGMII_CARD_PORT4_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC10, SGMII_CARD_PORT3_PHY_ADDR); + break; + case 38: + /* QSGMII in Slot3 and Slot4 */ + fm_info_set_phy_address(FM2_DTSEC1, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC2, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC3, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC4, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC5, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC6, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC9, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC10, QSGMII_CARD_PHY_ADDR); + break; + case 40: + case 46: + case 48: + /* SGMII in Slot3 */ + fm_info_set_phy_address(FM2_DTSEC5, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC6, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC9, SGMII_CARD_PORT4_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC10, SGMII_CARD_PORT3_PHY_ADDR); + /* QSGMII in Slot4 */ + fm_info_set_phy_address(FM2_DTSEC1, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC2, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC3, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC4, QSGMII_CARD_PHY_ADDR); + break; + case 50: + case 52: + case 54: + fm_info_set_phy_address(FM2_10GEC1, FM2_10GEC1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC1, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC2, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC3, QSGMII_CARD_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC4, QSGMII_CARD_PHY_ADDR); + break; + case 56: + case 57: + /* XFI in Slot3, SGMII in Slot4 */ + fm_info_set_phy_address(FM1_10GEC1, XFI_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM1_10GEC2, XFI_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM2_10GEC2, XFI_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM2_10GEC1, XFI_CARD_PORT4_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC2, SGMII_CARD_PORT2_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC3, SGMII_CARD_PORT3_PHY_ADDR); + fm_info_set_phy_address(FM2_DTSEC4, SGMII_CARD_PORT4_PHY_ADDR); + break; + default: + puts("Invalid SerDes2 protocol for T4240QDS\n"); + break; + } + + for (i = FM2_DTSEC1; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) { + int idx = i - FM2_DTSEC1, lane, slot; + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_SGMII: + lane = serdes_get_first_lane(FSL_SRDS_2, + SGMII_FM2_DTSEC1 + idx); + if (lane < 0) + break; + slot = lane_to_slot_fsm2[lane]; + debug("FM2@DTSEC%u expects SGMII in slot %u\n", + idx + 1, slot); + if (QIXIS_READ(present2) & (1 << (slot - 1))) + fm_disable_port(i); + switch (slot) { + case 3: + mdio_mux[i] = EMI1_SLOT3; + fm_info_set_mdio(i, + mii_dev_for_muxval(mdio_mux[i])); + break; + case 4: + mdio_mux[i] = EMI1_SLOT4; + fm_info_set_mdio(i, + mii_dev_for_muxval(mdio_mux[i])); + break; + }; + break; + case PHY_INTERFACE_MODE_RGMII: + /* + * If DTSEC5 is RGMII, then it's routed via via EC1 to + * the first on-board RGMII port. If DTSEC6 is RGMII, + * then it's routed via via EC2 to the second on-board + * RGMII port. + */ + debug("FM2@DTSEC%u is RGMII at address %u\n", + idx + 1, i == FM2_DTSEC5 ? 1 : 2); + fm_info_set_phy_address(i, i == FM2_DTSEC5 ? 1 : 2); + mdio_mux[i] = EMI1_RGMII; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } + + for (i = FM2_10GEC1; i < FM2_10GEC1 + CONFIG_SYS_NUM_FM2_10GEC; i++) { + switch (fm_info_get_enet_if(i)) { + case PHY_INTERFACE_MODE_XGMII: + mdio_mux[i] = EMI2; + fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i])); + break; + default: + break; + } + } +#endif /* CONFIG_SYS_NUM_FMAN */ + + cpu_eth_init(bis); +#endif /* CONFIG_FMAN_ENET */ + + return pci_eth_init(bis); +} diff --git a/board/freescale/t4qds/law.c b/board/freescale/t4qds/law.c new file mode 100644 index 0000000000..5debcf612a --- /dev/null +++ b/board/freescale/t4qds/law.c @@ -0,0 +1,47 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC), +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN), +#endif + SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC), +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/t4qds/pci.c b/board/freescale/t4qds/pci.c new file mode 100644 index 0000000000..fc00b4ad6d --- /dev/null +++ b/board/freescale/t4qds/pci.c @@ -0,0 +1,39 @@ +/* + * Copyright 2007-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} + +void pci_of_setup(void *blob, bd_t *bd) +{ + FT_FSL_PCI_SETUP; +} diff --git a/board/freescale/t4qds/t4240qds_qixis.h b/board/freescale/t4qds/t4240qds_qixis.h new file mode 100644 index 0000000000..efb718d2c3 --- /dev/null +++ b/board/freescale/t4qds/t4240qds_qixis.h @@ -0,0 +1,56 @@ +/* + * Copyright 2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __T4020QDS_QIXIS_H__ +#define __T4020QDS_QIXIS_H__ + +/* Definitions of QIXIS Registers for T4020QDS */ + +/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */ +#define BRDCFG4_EMISEL_MASK 0xE0 +#define BRDCFG4_EMISEL_SHIFT 5 + +/* SYSCLK */ +#define QIXIS_SYSCLK_66 0x0 +#define QIXIS_SYSCLK_83 0x1 +#define QIXIS_SYSCLK_100 0x2 +#define QIXIS_SYSCLK_125 0x3 +#define QIXIS_SYSCLK_133 0x4 +#define QIXIS_SYSCLK_150 0x5 +#define QIXIS_SYSCLK_160 0x6 +#define QIXIS_SYSCLK_166 0x7 + +/* DDRCLK */ +#define QIXIS_DDRCLK_66 0x0 +#define QIXIS_DDRCLK_100 0x1 +#define QIXIS_DDRCLK_125 0x2 +#define QIXIS_DDRCLK_133 0x3 + +#define BRDCFG5_RESET 0x00 + +#define BRDCFG12_SD3EN_MASK 0x20 +#define BRDCFG12_SD3MX_MASK 0x08 +#define BRDCFG12_SD3MX_SLOT5 0x08 +#define BRDCFG12_SD3MX_SLOT6 0x00 +#define BRDCFG12_SD4EN_MASK 0x04 +#define BRDCFG12_SD4MX_MASK 0x03 +#define BRDCFG12_SD4MX_SLOT7 0x02 +#define BRDCFG12_SD4MX_SLOT8 0x01 +#define BRDCFG12_SD4MX_AURO_SATA 0x00 +#endif diff --git a/board/freescale/t4qds/t4qds.c b/board/freescale/t4qds/t4qds.c new file mode 100644 index 0000000000..88b8cedf48 --- /dev/null +++ b/board/freescale/t4qds/t4qds.c @@ -0,0 +1,395 @@ +/* + * Copyright 2009-2012 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "../common/qixis.h" +#include "../common/vsc3316_3308.h" +#include "t4qds.h" +#include "t4240qds_qixis.h" + +DECLARE_GLOBAL_DATA_PTR; + +int checkboard(void) +{ + u8 sw; + struct cpu_type *cpu = gd->cpu; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + unsigned int i; + + printf("Board: %sQDS, ", cpu->name); + printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ", + QIXIS_READ(id), QIXIS_READ(arch), QIXIS_READ(scver)); + + sw = QIXIS_READ(brdcfg[0]); + sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; + + if (sw < 0x8) + printf("vBank: %d\n", sw); + else if (sw == 0x8) + puts("Promjet\n"); + else if (sw == 0x9) + puts("NAND\n"); + else + printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); + + /* Display the RCW, so that no one gets confused as to what RCW + * we're actually using for this boot. + */ + puts("Reset Configuration Word (RCW):"); + for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) { + u32 rcw = in_be32(&gur->rcwsr[i]); + + if ((i % 4) == 0) + printf("\n %08x:", i * 4); + printf(" %08x", rcw); + } + puts("\n"); + + /* + * Display the actual SERDES reference clocks as configured by the + * dip switches on the board. Note that the SWx registers could + * technically be set to force the reference clocks to match the + * values that the SERDES expects (or vice versa). For now, however, + * we just display both values and hope the user notices when they + * don't match. + */ + puts("SERDES Reference Clocks: "); + sw = QIXIS_READ(brdcfg[2]); + for (i = 0; i < MAX_SERDES; i++) { + static const char *freq[] = { + "100", "125", "156.25", "161.1328125"}; + unsigned int clock = (sw >> (2 * i)) & 3; + + printf("SERDES%u=%sMHz ", i+1, freq[clock]); + } + puts("\n"); + + return 0; +} + +int select_i2c_ch_pca9547(u8 ch) +{ + int ret; + + ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); + if (ret) { + puts("PCA: failed to select proper channel\n"); + return ret; + } + + return 0; +} + +/* Configure Crossbar switches for Front-Side SerDes Ports */ +int config_frontside_crossbar_vsc3316(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_prtcl_s1, srds_prtcl_s2; + int ret; + + ret = select_i2c_ch_pca9547(I2C_MUX_CH_VSC3316_FS); + if (ret) + return ret; + + srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS1_PRTCL; + srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; + if (srds_prtcl_s1) { + ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm1_tx, 8); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm1_rx, 8); + if (ret) + return ret; + } + + srds_prtcl_s2 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS2_PRTCL; + srds_prtcl_s2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT; + if (srds_prtcl_s2) { + ret = vsc3316_config(VSC3316_FSM_TX_ADDR, vsc3316_fsm2_tx, 8); + if (ret) + return ret; + ret = vsc3316_config(VSC3316_FSM_RX_ADDR, vsc3316_fsm2_rx, 8); + if (ret) + return ret; + } + + return 0; +} + +int config_backside_crossbar_mux(void) +{ + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + u32 srds_prtcl_s3, srds_prtcl_s4; + u8 brdcfg; + + srds_prtcl_s3 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS3_PRTCL; + srds_prtcl_s3 >>= FSL_CORENET2_RCWSR4_SRDS3_PRTCL_SHIFT; + switch (srds_prtcl_s3) { + case 0: + /* SerDes3 is not enabled */ + break; + case 2: + case 9: + case 10: + /* SD3(0:7) => SLOT5(0:7) */ + brdcfg = QIXIS_READ(brdcfg[12]); + brdcfg &= ~BRDCFG12_SD3MX_MASK; + brdcfg |= BRDCFG12_SD3MX_SLOT5; + QIXIS_WRITE(brdcfg[12], brdcfg); + break; + case 4: + case 6: + case 8: + case 12: + case 14: + case 16: + case 17: + case 19: + case 20: + /* SD3(4:7) => SLOT6(0:3) */ + brdcfg = QIXIS_READ(brdcfg[12]); + brdcfg &= ~BRDCFG12_SD3MX_MASK; + brdcfg |= BRDCFG12_SD3MX_SLOT6; + QIXIS_WRITE(brdcfg[12], brdcfg); + break; + default: + printf("WARNING: unsupported for SerDes3 Protocol %d\n", + srds_prtcl_s3); + return -1; + } + + srds_prtcl_s4 = in_be32(&gur->rcwsr[4]) & + FSL_CORENET2_RCWSR4_SRDS4_PRTCL; + srds_prtcl_s4 >>= FSL_CORENET2_RCWSR4_SRDS4_PRTCL_SHIFT; + switch (srds_prtcl_s4) { + case 0: + /* SerDes4 is not enabled */ + break; + case 2: + /* 10b, SD4(0:7) => SLOT7(0:7) */ + brdcfg = QIXIS_READ(brdcfg[12]); + brdcfg &= ~BRDCFG12_SD4MX_MASK; + brdcfg |= BRDCFG12_SD4MX_SLOT7; + QIXIS_WRITE(brdcfg[12], brdcfg); + break; + case 4: + case 6: + case 8: + /* x1b, SD4(4:7) => SLOT8(0:3) */ + brdcfg = QIXIS_READ(brdcfg[12]); + brdcfg &= ~BRDCFG12_SD4MX_MASK; + brdcfg |= BRDCFG12_SD4MX_SLOT8; + QIXIS_WRITE(brdcfg[12], brdcfg); + break; + case 10: + case 12: + case 14: + case 16: + case 18: + /* 00b, SD4(4:5) => AURORA, SD4(6:7) => SATA */ + brdcfg = QIXIS_READ(brdcfg[12]); + brdcfg &= ~BRDCFG12_SD4MX_MASK; + brdcfg |= BRDCFG12_SD4MX_AURO_SATA; + QIXIS_WRITE(brdcfg[12], brdcfg); + break; + default: + printf("WARNING: unsupported for SerDes4 Protocol %d\n", + srds_prtcl_s4); + return -1; + } + + return 0; +} + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + set_liodns(); +#ifdef CONFIG_SYS_DPAA_QBMAN + setup_portals(); +#endif + + /* Disable remote I2C connectoin */ + QIXIS_WRITE(brdcfg[5], BRDCFG5_RESET); + + /* Configure board SERDES ports crossbar */ + config_frontside_crossbar_vsc3316(); + config_backside_crossbar_mux(); + select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); + + return 0; +} + +unsigned long get_board_sys_clk(void) +{ + u8 sysclk_conf = QIXIS_READ(brdcfg[1]); + + switch (sysclk_conf & 0x0F) { + case QIXIS_SYSCLK_83: + return 83333333; + case QIXIS_SYSCLK_100: + return 100000000; + case QIXIS_SYSCLK_125: + return 125000000; + case QIXIS_SYSCLK_133: + return 133333333; + case QIXIS_SYSCLK_150: + return 150000000; + case QIXIS_SYSCLK_160: + return 160000000; + case QIXIS_SYSCLK_166: + return 166666666; + } + return 66666666; +} + +unsigned long get_board_ddr_clk(void) +{ + u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); + + switch ((ddrclk_conf & 0x30) >> 4) { + case QIXIS_DDRCLK_100: + return 100000000; + case QIXIS_DDRCLK_125: + return 125000000; + case QIXIS_DDRCLK_133: + return 133333333; + } + return 66666666; +} + +static const char *serdes_clock_to_string(u32 clock) +{ + switch (clock) { + case SRDS_PLLCR0_RFCK_SEL_100: + return "100"; + case SRDS_PLLCR0_RFCK_SEL_125: + return "125"; + case SRDS_PLLCR0_RFCK_SEL_156_25: + return "156.25"; + case SRDS_PLLCR0_RFCK_SEL_161_13: + return "161.1328125"; + default: + return "???"; + } +} + +int misc_init_r(void) +{ + u8 sw; + serdes_corenet_t *srds_regs = + (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR; + u32 actual[MAX_SERDES]; + unsigned int i; + + sw = QIXIS_READ(brdcfg[2]); + for (i = 0; i < MAX_SERDES; i++) { + unsigned int clock = (sw >> (2 * i)) & 3; + switch (clock) { + case 0: + actual[i] = SRDS_PLLCR0_RFCK_SEL_100; + break; + case 1: + actual[i] = SRDS_PLLCR0_RFCK_SEL_125; + break; + case 2: + actual[i] = SRDS_PLLCR0_RFCK_SEL_156_25; + break; + case 3: + actual[i] = SRDS_PLLCR0_RFCK_SEL_161_13; + break; + } + } + + for (i = 0; i < MAX_SERDES; i++) { + u32 pllcr0 = srds_regs->bank[i].pllcr0; + u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK; + if (expected != actual[i]) { + printf("Warning: SERDES%u expects reference clock" + " %sMHz, but actual is %sMHz\n", i + 1, + serdes_clock_to_string(expected), + serdes_clock_to_string(actual[i])); + } + } + + return 0; +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_PCI + pci_of_setup(blob, bd); +#endif + + fdt_fixup_liodn(blob); + fdt_fixup_dr_usb(blob, bd); + +#ifdef CONFIG_SYS_DPAA_FMAN + fdt_fixup_fman_ethernet(blob); + fdt_fixup_board_enet(blob); +#endif +} diff --git a/board/freescale/t4qds/t4qds.h b/board/freescale/t4qds/t4qds.h new file mode 100644 index 0000000000..c6a3492cb6 --- /dev/null +++ b/board/freescale/t4qds/t4qds.h @@ -0,0 +1,37 @@ +/* + * Copyright 2011-2012 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CORENET_DS_H__ +#define __CORENET_DS_H__ + +void fdt_fixup_board_enet(void *blob); +void pci_of_setup(void *blob, bd_t *bd); + +static const int8_t vsc3316_fsm1_tx[8][2] = { {0, 0}, {1, 1}, {6, 6}, {7, 7}, + {8, 8}, {9, 9}, {14, 14}, {15, 15} }; + +static const int8_t vsc3316_fsm2_tx[8][2] = { {2, 2}, {3, 3}, {4, 4}, {5, 5}, + {10, 10}, {11, 11}, {12, 12}, {13, 13} }; + +static const int8_t vsc3316_fsm1_rx[8][2] = { {2, 12}, {3, 13}, {4, 5}, {5, 4}, + {10, 11}, {11, 10}, {12, 2}, {13, 3} }; + +static const int8_t vsc3316_fsm2_rx[8][2] = { {0, 15}, {1, 14}, {6, 7}, {7, 6}, + {8, 9}, {9, 8}, {14, 1}, {15, 0} }; +#endif diff --git a/board/freescale/t4qds/tlb.c b/board/freescale/t4qds/tlb.c new file mode 100644 index 0000000000..078a6e415c --- /dev/null +++ b/board/freescale/t4qds/tlb.c @@ -0,0 +1,136 @@ +/* + * Copyright 2008-2012 Freescale Semiconductor, Inc. + * + * (C) Copyright 2000 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, + CONFIG_SYS_INIT_RAM_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ +#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR) + /* + * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the + * SRAM is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), +#else + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#endif + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_16M, 1), + + /* *I*G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000, + CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ +#ifdef CONFIG_SYS_BMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 9, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_QMAN_MEM_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 11, BOOKE_PAGESZ_16M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 12, BOOKE_PAGESZ_16M, 1), +#endif +#ifdef CONFIG_SYS_DCSRBAR_PHYS + SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 13, BOOKE_PAGESZ_4M, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE + /* + * *I*G - NAND + * entry 14 and 15 has been used hard coded, they will be disabled + * in cpu_init_f, so we use entry 16 for nand. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 16, BOOKE_PAGESZ_1M, 1), +#endif + SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 17, BOOKE_PAGESZ_4K, 1), + +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); -- cgit v1.2.1