From 49249e137daeec4d51c99aa69a8459d2f11cd94d Mon Sep 17 00:00:00 2001 From: Poonam Aggrwal Date: Wed, 9 Feb 2011 19:17:53 +0000 Subject: powerpc/85xx: Add basic support for P1010RDB Boot methods supported: NOR Flash, SPI Flash and SDCARD This patch adds the following basic interfaces: DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash. P1010RDB Overview ----------------- 1Gbyte DDR3 (on board DDR) Local Bus (IFC): 32Mbyte 16bit NOR flash 32Mbyte SLC NAND Flash 64KB CPLD device(GPCM interface) SPI Flash: 128 Mbit SPI Flash memory SD/MMC: connector to interface with the SD memory card SATA: 1 internal SATA connect to 2.5. 160G SATA2 HDD 1 eSATA connector to rear panel USB 2.0: x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface. x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet eTSEC: eTSEC1: Connected to RGMII PHY VSC8641XKO eTSEC2: Connected to SGMII PHY VSC8221 eTSEC3: Connected to SGMII PHY VSC8221 eCAN: Two DB-9 female connectors for Field bus interface UART: supports two UARTs up to 115200 bps for console TDM: 2 FXS ports connected via an external SLIC to the TDM interface. SLIC: SPI SLIC I2C: Serial EEprom Real time clock 256 Kbit M24256 I2C EEPROM PCIe: PCIe and mPCIe connectors. Signed-off-by: Poonam Aggrwal Signed-off-by: Dipen Dudhat Signed-off-by: Prabhakar Kushwaha Signed-off-by: Ramneek Mehresh Signed-off-by: Bhaskar Upadhaya Signed-off-by: York Sun Signed-off-by: Kumar Gala --- board/freescale/p1010rdb/Makefile | 52 ++++++ board/freescale/p1010rdb/ddr.c | 250 +++++++++++++++++++++++++++ board/freescale/p1010rdb/law.c | 35 ++++ board/freescale/p1010rdb/p1010rdb.c | 330 ++++++++++++++++++++++++++++++++++++ board/freescale/p1010rdb/tlb.c | 98 +++++++++++ 5 files changed, 765 insertions(+) create mode 100644 board/freescale/p1010rdb/Makefile create mode 100644 board/freescale/p1010rdb/ddr.c create mode 100644 board/freescale/p1010rdb/law.c create mode 100644 board/freescale/p1010rdb/p1010rdb.c create mode 100644 board/freescale/p1010rdb/tlb.c (limited to 'board/freescale/p1010rdb') diff --git a/board/freescale/p1010rdb/Makefile b/board/freescale/p1010rdb/Makefile new file mode 100644 index 0000000000..1dcd490721 --- /dev/null +++ b/board/freescale/p1010rdb/Makefile @@ -0,0 +1,52 @@ +# +# Copyright 2010-2011 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1010rdb/ddr.c b/board/freescale/p1010rdb/ddr.c new file mode 100644 index 0000000000..e5d8423df0 --- /dev/null +++ b/board/freescale/p1010rdb/ddr.c @@ -0,0 +1,250 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +#ifndef CONFIG_DDR_RAW_TIMING +#define CONFIG_SYS_DRAM_SIZE 1024 + +fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = { + .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, + .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, + .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, + .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800, + .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800, + .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800, + .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800, + .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL, + .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2, + .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_800, + .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800, + .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, + .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_800, + .ddr_data_init = CONFIG_MEM_INIT_VALUE, + .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800, + .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, + .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, + .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, + .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, + .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL, + .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_800, + .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR, + .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, + .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 +}; + +fsl_ddr_cfg_regs_t ddr_cfg_regs_667 = { + .cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS, + .cs[0].config = CONFIG_SYS_DDR_CS0_CONFIG, + .cs[0].config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2, + .timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_667, + .timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_667, + .timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_667, + .timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_667, + .ddr_sdram_cfg = CONFIG_SYS_DDR_CONTROL, + .ddr_sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL_2, + .ddr_sdram_mode = CONFIG_SYS_DDR_MODE_1_667, + .ddr_sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_667, + .ddr_sdram_md_cntl = CONFIG_SYS_DDR_MODE_CONTROL, + .ddr_sdram_interval = CONFIG_SYS_DDR_INTERVAL_667, + .ddr_data_init = CONFIG_MEM_INIT_VALUE, + .ddr_sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_667, + .ddr_init_addr = CONFIG_SYS_DDR_INIT_ADDR, + .ddr_init_ext_addr = CONFIG_SYS_DDR_INIT_EXT_ADDR, + .timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4, + .timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5, + .ddr_zq_cntl = CONFIG_SYS_DDR_ZQ_CONTROL, + .ddr_wrlvl_cntl = CONFIG_SYS_DDR_WRLVL_CONTROL_667, + .ddr_sr_cntr = CONFIG_SYS_DDR_SR_CNTR, + .ddr_sdram_rcw_1 = CONFIG_SYS_DDR_RCW_1, + .ddr_sdram_rcw_2 = CONFIG_SYS_DDR_RCW_2 +}; + +fixed_ddr_parm_t fixed_ddr_parm_0[] = { + {750, 850, &ddr_cfg_regs_800}, + {607, 749, &ddr_cfg_regs_667}, + {0, 0, NULL} +}; + +unsigned long get_sdram_size(void) +{ + struct cpu_type *cpu; + phys_size_t ddr_size; + + cpu = gd->cpu; + /* P1014 and it's derivatives support max 16it DDR width */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) + ddr_size = (CONFIG_SYS_DRAM_SIZE / 2); + else + ddr_size = CONFIG_SYS_DRAM_SIZE; + + return ddr_size; +} + +/* + * Fixed sdram init -- doesn't use serial presence detect. + */ +phys_size_t fixed_sdram(void) +{ + int i; + char buf[32]; + fsl_ddr_cfg_regs_t ddr_cfg_regs; + phys_size_t ddr_size; + ulong ddr_freq, ddr_freq_mhz; + struct cpu_type *cpu; + +#if defined(CONFIG_SYS_RAMBOOT) + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; +#endif + + ddr_freq = get_ddr_freq(0); + ddr_freq_mhz = ddr_freq / 1000000; + + printf("Configuring DDR for %s MT/s data rate\n", + strmhz(buf, ddr_freq)); + + for (i = 0; fixed_ddr_parm_0[i].max_freq > 0; i++) { + if ((ddr_freq_mhz > fixed_ddr_parm_0[i].min_freq) && + (ddr_freq_mhz <= fixed_ddr_parm_0[i].max_freq)) { + memcpy(&ddr_cfg_regs, fixed_ddr_parm_0[i].ddr_settings, + sizeof(ddr_cfg_regs)); + break; + } + } + + if (fixed_ddr_parm_0[i].max_freq == 0) + panic("Unsupported DDR data rate %s MT/s data rate\n", + strmhz(buf, ddr_freq)); + + cpu = gd->cpu; + /* P1014 and it's derivatives support max 16bit DDR width */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) { + ddr_cfg_regs.ddr_sdram_cfg |= SDRAM_CFG_16_BE; + ddr_cfg_regs.cs[0].bnds = CONFIG_SYS_DDR_CS0_BNDS >> 1; + ddr_cfg_regs.ddr_sdram_cfg &= ~0x00180000; + ddr_cfg_regs.ddr_sdram_cfg |= 0x001080000; + } + + ddr_size = (phys_size_t) CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; + fsl_ddr_set_memctl_regs(&ddr_cfg_regs, 0); + + if (set_ddr_laws(CONFIG_SYS_DDR_SDRAM_BASE, ddr_size, + LAW_TRGT_IF_DDR_1) < 0) { + printf("ERROR setting Local Access Windows for DDR\n"); + return 0; + } + + return ddr_size; +} + +#else /* CONFIG_DDR_RAW_TIMING */ +/* + * Samsung K4B2G0846C-HCF8 + * The following timing are for "downshift" + * i.e. to use CL9 part as CL7 + * otherwise, tAA, tRCD, tRP will be 13500ps + * and tRC will be 49500ps + */ +dimm_params_t ddr_raw_timing = { + .n_ranks = 1, + .rank_density = 1073741824u, + .capacity = 1073741824u, + .primary_sdram_width = 32, + .ec_sdram_width = 0, + .registered_dimm = 0, + .mirrored_dimm = 0, + .n_row_addr = 15, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 0, + .burst_lengths_bitmask = 0x0c, + + .tCKmin_X_ps = 1875, + .caslat_X = 0x1e << 4, /* 5,6,7,8 */ + .tAA_ps = 13125, + .tWR_ps = 15000, + .tRCD_ps = 13125, + .tRRD_ps = 7500, + .tRP_ps = 13125, + .tRAS_ps = 37500, + .tRC_ps = 50625, + .tRFC_ps = 160000, + .tWTR_ps = 7500, + .tRTP_ps = 7500, + .refresh_rate_ps = 7800000, + .tFAW_ps = 37500, +}; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "Fixed DDR on board"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + struct cpu_type *cpu; + int i; + popts->clk_adjust = 6; + popts->cpo_override = 0x1f; + popts->write_data_delay = 2; + popts->half_strength_driver_enable = 1; + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x8; + popts->trwt_override = 1; + popts->trwt = 0; + + cpu = gd->cpu; + /* P1014 and it's derivatives support max 16it DDR width */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) + popts->data_bus_width = DDR_DATA_BUS_WIDTH_16; + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; + } +} + +#endif /* CONFIG_DDR_RAW_TIMING */ diff --git a/board/freescale/p1010rdb/law.c b/board/freescale/p1010rdb/law.c new file mode 100644 index 0000000000..3ed77fc401 --- /dev/null +++ b/board/freescale/p1010rdb/law.c @@ -0,0 +1,35 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include + +struct law_entry law_table[] = { +#ifndef CONFIG_SDCARD + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), +#endif +}; + +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c new file mode 100644 index 0000000000..03e9da1940 --- /dev/null +++ b/board/freescale/p1010rdb/p1010rdb.c @@ -0,0 +1,330 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#ifndef CONFIG_SDCARD +#include +#endif + +DECLARE_GLOBAL_DATA_PTR; + +#define GPIO4_PCIE_RESET_SET 0x08000000 +#define MUX_CPLD_CAN_UART 0x00 +#define MUX_CPLD_TDM 0x01 +#define MUX_CPLD_SPICS0_FLASH 0x00 +#define MUX_CPLD_SPICS0_SLIC 0x02 + +#ifndef CONFIG_SDCARD +struct cpld_data { + u8 cpld_ver; /* cpld revision */ + u8 pcba_ver; /* pcb revision number */ + u8 twindie_ddr3; + u8 res1[6]; + u8 bank_sel; /* NOR Flash bank */ + u8 res2[5]; + u8 usb2_sel; + u8 res3[1]; + u8 porsw_sel; + u8 tdm_can_sel; + u8 spi_cs0_sel; /* SPI CS0 SLIC/SPI Flash */ + u8 por0; /* POR Options */ + u8 por1; /* POR Options */ + u8 por2; /* POR Options */ + u8 por3; /* POR Options */ +}; + +void cpld_show(void) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + + printf("CPLD: V%x.%x PCBA: V%x.0\n", + in_8(&cpld_data->cpld_ver) & 0xF0, + in_8(&cpld_data->cpld_ver) & 0x0F, + in_8(&cpld_data->pcba_ver) & 0x0F); + +#ifdef CONFIG_DEBUG + printf("twindie_ddr =%x\n", + in_8(&cpld_data->twindie_ddr3)); + printf("bank_sel =%x\n", + in_8(&cpld_data->bank_sel)); + printf("usb2_sel =%x\n", + in_8(&cpld_data->usb2_sel)); + printf("porsw_sel =%x\n", + in_8(&cpld_data->porsw_sel)); + printf("tdm_can_sel =%x\n", + in_8(&cpld_data->tdm_can_sel)); + printf("tdm_can_sel =%x\n", + in_8(&cpld_data->tdm_can_sel)); + printf("spi_cs0_sel =%x\n", + in_8(&cpld_data->spi_cs0_sel)); + printf("bcsr0 =%x\n", + in_8(&cpld_data->bcsr0)); + printf("bcsr1 =%x\n", + in_8(&cpld_data->bcsr1)); + printf("bcsr2 =%x\n", + in_8(&cpld_data->bcsr2)); + printf("bcsr3 =%x\n", + in_8(&cpld_data->bcsr3)); +#endif +} +#endif + +int board_early_init_f(void) +{ + ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR); +#ifndef CONFIG_SDCARD + struct fsl_ifc *ifc = (void *)CONFIG_SYS_IFC_ADDR; + + /* Clock configuration to access CPLD using IFC(GPCM) */ + setbits_be32(&ifc->ifc_gcr, 1 << IFC_GCR_TBCTL_TRN_TIME_SHIFT); +#endif + /* + * Reset PCIe slots via GPIO4 + */ + setbits_be32(&pgpio->gpdir, GPIO4_PCIE_RESET_SET); + setbits_be32(&pgpio->gpdat, GPIO4_PCIE_RESET_SET); + + return 0; +} + +int board_early_init_r(void) +{ +#ifndef CONFIG_SDCARD + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_16M, 1); + + set_tlb(1, flashbase + 0x1000000, + CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel+1, BOOKE_PAGESZ_16M, 1); +#endif + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif /* ifdef CONFIG_PCI */ + +int checkboard(void) +{ + struct cpu_type *cpu; + + cpu = gd->cpu; + printf("Board: %sRDB ", cpu->name); +#ifdef CONFIG_PHYS_64BIT + puts("(36-bit addrmap)"); +#endif + puts("\n"); + + return 0; +} + +#ifdef CONFIG_TSEC_ENET +int board_eth_init(bd_t *bis) +{ + struct fsl_pq_mdio_info mdio_info; + struct tsec_info_struct tsec_info[4]; + struct cpu_type *cpu; + int num = 0; + + cpu = gd->cpu; + +#ifdef CONFIG_TSEC1 + SET_STD_TSEC_INFO(tsec_info[num], 1); + num++; +#endif +#ifdef CONFIG_TSEC2 + SET_STD_TSEC_INFO(tsec_info[num], 2); + num++; +#endif +#ifdef CONFIG_TSEC3 + /* P1014 and it's derivatives do not support eTSEC3 */ + if (cpu->soc_ver != SVR_P1014 && cpu->soc_ver != SVR_P1014_E) { + SET_STD_TSEC_INFO(tsec_info[num], 3); + num++; + } +#endif + if (!num) { + printf("No TSECs initialized\n"); + return 0; + } + + mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR; + mdio_info.name = DEFAULT_MII_NAME; + + fsl_pq_mdio_init(bis, &mdio_info); + + tsec_eth_init(bis, tsec_info, num); + + return pci_eth_init(bis); +} +#endif + +#if defined(CONFIG_OF_BOARD_SETUP) +void fdt_del_flexcan(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "fsl,flexcan-v1.0")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void fdt_del_spi_flash(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "spansion,s25sl12801")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void fdt_del_spi_slic(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "zarlink,le88266")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void fdt_del_tdm(void *blob) +{ + int nodeoff = 0; + + while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, + "fsl,starlite-tdm")) >= 0) { + fdt_del_node(blob, nodeoff); + } +} + +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + struct cpu_type *cpu; + + cpu = gd->cpu; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + +#if defined(CONFIG_PCI) + FT_FSL_PCI_SETUP; +#endif + + fdt_fixup_memory(blob, (u64)base, (u64)size); + + fdt_fixup_dr_usb(blob, bd); + + /* P1014 and it's derivatives don't support CAN and eTSEC3 */ + if (cpu->soc_ver == SVR_P1014 || cpu->soc_ver == SVR_P1014_E) { + fdt_del_flexcan(blob); + fdt_del_node_and_alias(blob, "ethernet2"); + } +#ifndef CONFIG_SDCARD + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { + printf("fdt CAN"); + fdt_del_tdm(blob); + fdt_del_spi_slic(blob); + } +#ifndef CONFIG_SPIFLASH + else if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { + printf("fdt TDM"); + fdt_del_flexcan(blob); + fdt_del_spi_flash(blob); + } +#endif +#endif +} +#endif + +#ifndef CONFIG_SDCARD +int misc_init_r(void) +{ + struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE); + ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); + + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "can")) { + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN1_TDM | + MPC85xx_PMUXCR_CAN1_UART | + MPC85xx_PMUXCR_CAN2_TDM | + MPC85xx_PMUXCR_CAN2_UART); + out_8(&cpld_data->tdm_can_sel, MUX_CPLD_CAN_UART); + } +#ifndef CONFIG_SPIFLASH + if (hwconfig_subarg_cmp("fsl_p1010mux", "tdm_can", "tdm")) { + printf("TDM"); + clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_UART | + MPC85xx_PMUXCR_CAN1_UART); + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_CAN2_TDM | + MPC85xx_PMUXCR_CAN1_TDM); + clrbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_GPIO); + setbits_be32(&gur->pmuxcr2, MPC85xx_PMUXCR2_UART_TDM); + out_8(&cpld_data->tdm_can_sel, MUX_CPLD_TDM); + out_8(&cpld_data->spi_cs0_sel, MUX_CPLD_SPICS0_SLIC); + } +#endif + return 0; +} +#endif diff --git a/board/freescale/p1010rdb/tlb.c b/board/freescale/p1010rdb/tlb.c new file mode 100644 index 0000000000..4256bf4e57 --- /dev/null +++ b/board/freescale/p1010rdb/tlb.c @@ -0,0 +1,98 @@ +/* + * Copyright 2010-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024 , + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_1M, 1), + +#ifndef CONFIG_NAND_SPL +#ifndef CONFIG_SDCARD + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_16M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE + 0x1000000, + CONFIG_SYS_FLASH_BASE_PHYS + 0x1000000, + MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, + 0, 3, BOOKE_PAGESZ_16M, 1), +#endif + +#ifdef CONFIG_PCI + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256K, 1), +#endif +#endif + +#ifndef CONFIG_SDCARD + /* *I*G - Board CPLD */ + SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 7, BOOKE_PAGESZ_1M, 1), +#endif + +#if defined(CONFIG_SYS_RAMBOOT) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_1G, 1) +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); -- cgit v1.2.1