From 361b715bbfbebc96d31c0ee48c34c2e66f049684 Mon Sep 17 00:00:00 2001 From: Peng Fan Date: Sat, 11 Jul 2015 11:38:47 +0800 Subject: imx: mx6qpsabreauto: Add MX6QP SABREAUTO CPU3 board support 1. Add DDR script for mx6qpsabreauto board. 2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9] and init the enet pll output to 125Mhz. 3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN. Build target: mx6qpsabreauto_config Boot Log: U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800) CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz) CPU: Automotive temperature grade (-40C to 125C) at 34C Reset cause: POR Board: MX6Q-Sabreauto revA I2C: ready DRAM: 2 GiB PMIC: PFUZE100 ID=0x10 Flash: 32 MiB NAND: 0 MiB MMC: FSL_SDHC: 0 *** Warning - bad CRC, using default environment No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Note: In this patch, we still add a new config mx6qpsabreauto_config, since SPL is not supported now, and IMX_CONFIG is needed at build time, so add this config. Future, when SPL is converted, this config can be removed. Signed-off-by: Peng Fan Signed-off-by: Robin Gong Signed-off-by: Ye.Li Reviewed-by: Fabio Estevam --- board/freescale/mx6qsabreauto/mx6qp.cfg | 145 ++++++++++++++++++++++++++ board/freescale/mx6qsabreauto/mx6qsabreauto.c | 33 ++++-- 2 files changed, 171 insertions(+), 7 deletions(-) create mode 100644 board/freescale/mx6qsabreauto/mx6qp.cfg (limited to 'board/freescale/mx6qsabreauto') diff --git a/board/freescale/mx6qsabreauto/mx6qp.cfg b/board/freescale/mx6qsabreauto/mx6qp.cfg new file mode 100644 index 0000000000..2298c772cc --- /dev/null +++ b/board/freescale/mx6qsabreauto/mx6qp.cfg @@ -0,0 +1,145 @@ +/* + * Copyright (C) 2015 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer doc/README.imximage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ +/* image version */ + +#define __ASSEMBLY__ +#include + +IMAGE_VERSION 2 + +/* + * Boot Device : one of spi, sd, eimnor, nand, sata: + * spinor: flash_offset: 0x0400 + * nand: flash_offset: 0x0400 + * sata: flash_offset: 0x0400 + * sd/mmc: flash_offset: 0x0400 + * eimnor: flash_offset: 0x1000 + */ +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +DATA 4 0x020e0798 0x000C0000 +DATA 4 0x020e0758 0x00000000 +DATA 4 0x020e0588 0x00000030 +DATA 4 0x020e0594 0x00000030 +DATA 4 0x020e056c 0x00000030 +DATA 4 0x020e0578 0x00000030 +DATA 4 0x020e074c 0x00000030 +DATA 4 0x020e057c 0x00000030 +DATA 4 0x020e058c 0x00000000 +DATA 4 0x020e059c 0x00000030 +DATA 4 0x020e05a0 0x00000030 +DATA 4 0x020e078c 0x00000030 +DATA 4 0x020e0750 0x00020000 +DATA 4 0x020e05a8 0x00000030 +DATA 4 0x020e05b0 0x00000030 +DATA 4 0x020e0524 0x00000030 +DATA 4 0x020e051c 0x00000030 +DATA 4 0x020e0518 0x00000030 +DATA 4 0x020e050c 0x00000030 +DATA 4 0x020e05b8 0x00000030 +DATA 4 0x020e05c0 0x00000030 +DATA 4 0x020e0774 0x00020000 +DATA 4 0x020e0784 0x00000030 +DATA 4 0x020e0788 0x00000030 +DATA 4 0x020e0794 0x00000030 +DATA 4 0x020e079c 0x00000030 +DATA 4 0x020e07a0 0x00000030 +DATA 4 0x020e07a4 0x00000030 +DATA 4 0x020e07a8 0x00000030 +DATA 4 0x020e0748 0x00000030 +DATA 4 0x020e05ac 0x00000030 +DATA 4 0x020e05b4 0x00000030 +DATA 4 0x020e0528 0x00000030 +DATA 4 0x020e0520 0x00000030 +DATA 4 0x020e0514 0x00000030 +DATA 4 0x020e0510 0x00000030 +DATA 4 0x020e05bc 0x00000030 +DATA 4 0x020e05c4 0x00000030 +DATA 4 0x021b0800 0xa1390003 +DATA 4 0x021b080c 0x001b001e +DATA 4 0x021b0810 0x002e0029 +DATA 4 0x021b480c 0x001b002a +DATA 4 0x021b4810 0x0019002c +DATA 4 0x021b083c 0x43240334 +DATA 4 0x021b0840 0x0324031a +DATA 4 0x021b483c 0x43340344 +DATA 4 0x021b4840 0x03280276 +DATA 4 0x021b0848 0x44383A3E +DATA 4 0x021b4848 0x3C3C3846 +DATA 4 0x021b0850 0x2e303230 +DATA 4 0x021b4850 0x38283E34 +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 +DATA 4 0x021b481c 0x33333333 +DATA 4 0x021b4820 0x33333333 +DATA 4 0x021b4824 0x33333333 +DATA 4 0x021b4828 0x33333333 +DATA 4 0x021b08c0 0x24912492 +DATA 4 0x021b48c0 0x24912492 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b48b8 0x00000800 +DATA 4 0x021b0004 0x00020036 +DATA 4 0x021b0008 0x09444040 +DATA 4 0x021b000c 0x898E7955 +DATA 4 0x021b0010 0xFF328F64 +DATA 4 0x021b0014 0x01FF00DB +DATA 4 0x021b0018 0x00001740 +DATA 4 0x021b001c 0x00008000 + +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x008E1023 +DATA 4 0x021b0040 0x00000047 +DATA 4 0x021b0400 0x14420000 +DATA 4 0x021b0000 0x841A0000 +DATA 4 0x00bb0008 0x00000004 +DATA 4 0x00bb000c 0x2891E41A +DATA 4 0x00bb0038 0x00000564 +DATA 4 0x00bb0014 0x00000040 +DATA 4 0x00bb0028 0x00000020 +DATA 4 0x00bb002c 0x00000020 +DATA 4 0x021b001c 0x04088032 +DATA 4 0x021b001c 0x00008033 +DATA 4 0x021b001c 0x00048031 +DATA 4 0x021b001c 0x09408030 +DATA 4 0x021b001c 0x04008040 +DATA 4 0x021b0020 0x00005800 +DATA 4 0x021b0818 0x00011117 +DATA 4 0x021b4818 0x00011117 +DATA 4 0x021b0004 0x00025576 +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 +/* set the default clock gate to save power */ +DATA 4, 0x020c4068, 0x00C03F3F +DATA 4, 0x020c406c, 0x0030FC03 +DATA 4, 0x020c4070, 0x0FFFC000 +DATA 4, 0x020c4074, 0x3FF00000 +DATA 4, 0x020c4078, 0xFFFFF300 +DATA 4, 0x020c407c, 0x0F0000F3 +DATA 4, 0x020c4080, 0x00000FFF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4, 0x020e0010, 0xF00000CF +/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */ +DATA 4, 0x020e0018, 0x77177717 +DATA 4, 0x020e001c, 0x77177717 diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index 943a4bd5d5..98602f889e 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -354,9 +354,22 @@ int board_phy_config(struct phy_device *phydev) return 0; } -int board_eth_init(bd_t *bis) +static void setup_fec(void) { + if (is_mx6dqp()) { + /* + * select ENET MAC0 TX clock from PLL + */ + imx_iomux_set_gpr_register(5, 9, 1, 1); + enable_fec_anatop_clock(ENET_125MHZ); + } + setup_iomux_enet(); +} + +int board_eth_init(bd_t *bis) +{ + setup_fec(); return cpu_eth_init(bis); } @@ -495,17 +508,21 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs) int power_init_board(void) { struct pmic *p; - unsigned int ret; + unsigned int value; p = pfuze_common_init(I2C_PMIC); if (!p) return -ENODEV; - ret = pfuze_mode_init(p, APS_PFM); - if (ret < 0) - return ret; + if (is_mx6dqp()) { + /* set SW2 staby volatage 0.975V*/ + pmic_reg_read(p, PFUZE100_SW2STBY, &value); + value &= ~0x3f; + value |= 0x17; + pmic_reg_write(p, PFUZE100_SW2STBY, value); + } - return 0; + return pfuze_mode_init(p, APS_PFM); } #ifdef CONFIG_CMD_BMODE @@ -525,7 +542,9 @@ int board_late_init(void) #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG setenv("board_name", "SABREAUTO"); - if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) + if (is_mx6dqp()) + setenv("board_rev", "MX6QP"); + else if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) setenv("board_rev", "MX6Q"); else if (is_cpu_type(MXC_CPU_MX6DL) || is_cpu_type(MXC_CPU_MX6SOLO)) setenv("board_rev", "MX6DL"); -- cgit v1.2.1