From 373ee048a8bdc3291aa88b93da183a0bc3b34a22 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 28 Jan 2014 00:04:58 +0100 Subject: ARM: IXP: Remove actux1 board The board is unmaintained, just like the rest of the IXP. Signed-off-by: Marek Vasut Cc: Albert Aribaud Cc: Michael Schwingen Cc: Tom Rini --- board/actux1/Makefile | 8 --- board/actux1/actux1.c | 148 ----------------------------------------------- board/actux1/actux1_hw.h | 41 ------------- board/actux1/u-boot.lds | 99 ------------------------------- 4 files changed, 296 deletions(-) delete mode 100644 board/actux1/Makefile delete mode 100644 board/actux1/actux1.c delete mode 100644 board/actux1/actux1_hw.h delete mode 100644 board/actux1/u-boot.lds (limited to 'board/actux1') diff --git a/board/actux1/Makefile b/board/actux1/Makefile deleted file mode 100644 index 05a8669113..0000000000 --- a/board/actux1/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := actux1.o diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c deleted file mode 100644 index 03ccd936b4..0000000000 --- a/board/actux1/actux1.c +++ /dev/null @@ -1,148 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * (C) Copyright 2006 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * (C) Copyright 2002 - * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#ifdef CONFIG_PCI -#include -#include -#endif - -#include "actux1_hw.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* CS5: Debug port */ - writel(0x9d520003, IXP425_EXP_CS5); - /* CS6: HwRel */ - writel(0x81860001, IXP425_EXP_CS6); - /* CS7: LEDs */ - writel(0x80900003, IXP425_EXP_CS7); - return 0; -} - -int board_init(void) -{ - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x00000100; - - GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST); - - /* Setup GPIOs for PCI INTA */ - GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA); - GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA); - - /* Setup GPIOs for 33MHz clock output */ - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK); - GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK); - writel(0x011001FF, IXP425_GPIO_GPCLKR); - - udelay(533); - GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST); - - ACTUX1_LED1(2); - ACTUX1_LED2(2); - ACTUX1_LED3(0); - ACTUX1_LED4(0); - ACTUX1_LED5(0); - ACTUX1_LED6(0); - ACTUX1_LED7(0); - - ACTUX1_HS(ACTUX1_HS_DCD); - - return 0; -} - -/* - * Check Board Identity - */ -int checkboard(void) -{ - char buf[64]; - int i = getenv_f("serial#", buf, sizeof(buf)); - - puts("Board: AcTux-1 rev."); - putc(ACTUX1_BOARDREL + 'A' - 1); - - if (i > 0) { - puts(", serial# "); - puts(buf); - } - putc('\n'); - - return 0; -} - -/************************************************************************* - * get_board_rev() - setup to pass kernel board revision information - * 0 = reserved - * 1 = Rev. A - * 2 = Rev. B - *************************************************************************/ -u32 get_board_rev(void) -{ - return ACTUX1_BOARDREL; -} - -int dram_init(void) -{ - gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20); - return 0; -} - - -#ifdef CONFIG_PCI -struct pci_controller hose; - -void pci_init_board(void) -{ - pci_ixp_init(&hose); -} -#endif - -void reset_phy(void) -{ - u16 id1, id2; - - /* initialize the PHY */ - miiphy_reset("NPE0", CONFIG_PHY_ADDR); - - miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1); - miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2); - - id2 &= 0xFFF0; /* mask out revision bits */ - - if (id1 == 0x13 && id2 == 0x78e0) { - /* - * LXT971/LXT972 PHY: set LED outputs: - * LED1(green) = Link/ACT, - * LED2 (unused) = LINK, - * LED3(red) = Coll - */ - miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432); - } else if (id1 == 0x143 && id2 == 0xbc30) { - /* BCM5241: default values are OK */ - } else - printf("unknown ethernet PHY ID: %x %x\n", id1, id2); -} diff --git a/board/actux1/actux1_hw.h b/board/actux1/actux1_hw.h deleted file mode 100644 index 5627f24796..0000000000 --- a/board/actux1/actux1_hw.h +++ /dev/null @@ -1,41 +0,0 @@ -/* - * (C) Copyright 2007 - * Michael Schwingen, michael@schwingen.org - * - * hardware register definitions for the AcTux-1 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _ACTUX1_HW_H -#define _ACTUX1_HW_H - -/* 0 = LED off,1 = green, 2 = red, 3 = orange */ -#define ACTUX1_LED1(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 0) -#define ACTUX1_LED2(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 1) -#define ACTUX1_LED3(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 2) -#define ACTUX1_LED4(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 3) -#define ACTUX1_LED5(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 4) -#define ACTUX1_LED6(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 5) -#define ACTUX1_LED7(a) writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 6) -#define ACTUX1_HS(a) writeb((a), IXP425_EXP_BUS_CS7_BASE_PHYS + 7) -#define ACTUX1_HS_DCD 0x01 -#define ACTUX1_HS_DSR 0x02 - -#define ACTUX1_DBG_PORT IXP425_EXP_BUS_CS5_BASE_PHYS -#define ACTUX1_BOARDREL (readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F) - -/* GPIO settings */ -#define CONFIG_SYS_GPIO_PCI1_INTA 2 -#define CONFIG_SYS_GPIO_PCI2_INTA 3 -#define CONFIG_SYS_GPIO_I2C_SDA 4 -#define CONFIG_SYS_GPIO_I2C_SCL 5 -#define CONFIG_SYS_GPIO_DBGJUMPER 9 -#define CONFIG_SYS_GPIO_BUTTON1 10 -#define CONFIG_SYS_GPIO_DBGSENSE 11 -#define CONFIG_SYS_GPIO_DTR 12 -#define CONFIG_SYS_GPIO_IORST 13 /* Out */ -#define CONFIG_SYS_GPIO_PCI_CLK 14 /* Out */ -#define CONFIG_SYS_GPIO_EXTBUS_CLK 15 /* Out */ - -#endif diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds deleted file mode 100644 index 4716e4f0e0..0000000000 --- a/board/actux1/u-boot.lds +++ /dev/null @@ -1,99 +0,0 @@ -/* - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm") -OUTPUT_ARCH (arm) -ENTRY (_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN (4); - .text : { - *(.__image_copy_start) - arch/arm/cpu/ixp/start.o(.text*) - net/built-in.o(.text*) - board/actux1/built-in.o(.text*) - arch/arm/cpu/ixp/built-in.o(.text*) - drivers/input/built-in.o(.text*) - - . = env_offset; - common/env_embedded.o(.ppcenv) - *(.text*) - } - - . = ALIGN(4); - .rodata : { - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - . = ALIGN(4); - .data : { - *(.data*) - } - . = ALIGN(4); - .got : { - *(.got) - } - . =.; - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN (4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - _end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .hash : { *(.hash*) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} -- cgit v1.2.1