From f1056910434d87051ff8af80a84e248dd1670abb Mon Sep 17 00:00:00 2001 From: Thomas Chou Date: Sat, 7 Nov 2015 14:31:08 +0800 Subject: cfi_flash: convert to driver model Convert cfi flash to driver model. Signed-off-by: Thomas Chou Reviewed-by: Simon Glass --- doc/device-tree-bindings/mtd/mtd-physmap.txt | 88 ++++++++++++++++++++++++++++ drivers/mtd/Kconfig | 11 ++++ drivers/mtd/cfi_flash.c | 78 ++++++++++++++++++++++++ 3 files changed, 177 insertions(+) create mode 100644 doc/device-tree-bindings/mtd/mtd-physmap.txt diff --git a/doc/device-tree-bindings/mtd/mtd-physmap.txt b/doc/device-tree-bindings/mtd/mtd-physmap.txt new file mode 100644 index 0000000000..4b8c489438 --- /dev/null +++ b/doc/device-tree-bindings/mtd/mtd-physmap.txt @@ -0,0 +1,88 @@ +CFI or JEDEC memory-mapped NOR flash, MTD-RAM (NVRAM...) + +Flash chips (Memory Technology Devices) are often used for solid state +file systems on embedded devices. + + - compatible : should contain the specific model of mtd chip(s) + used, if known, followed by either "cfi-flash", "jedec-flash", + "mtd-ram" or "mtd-rom". + - reg : Address range(s) of the mtd chip(s) + It's possible to (optionally) define multiple "reg" tuples so that + non-identical chips can be described in one node. + - bank-width : Width (in bytes) of the bank. Equal to the + device width times the number of interleaved chips. + - device-width : (optional) Width of a single mtd chip. If + omitted, assumed to be equal to 'bank-width'. + - #address-cells, #size-cells : Must be present if the device has + sub-nodes representing partitions (see below). In this case + both #address-cells and #size-cells must be equal to 1. + - no-unaligned-direct-access: boolean to disable the default direct + mapping of the flash. + On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause + problems with JFFS2 usage, as the local bus (LPB) doesn't support + unaligned accesses as implemented in the JFFS2 code via memcpy(). + By defining "no-unaligned-direct-access", the flash will not be + exposed directly to the MTD users (e.g. JFFS2) any more. + - linux,mtd-name: allow to specify the mtd name for retro capability with + physmap-flash drivers as boot loader pass the mtd partition via the old + device name physmap-flash. + - use-advanced-sector-protection: boolean to enable support for the + advanced sector protection (Spansion: PPB - Persistent Protection + Bits) locking. + +For JEDEC compatible devices, the following additional properties +are defined: + + - vendor-id : Contains the flash chip's vendor id (1 byte). + - device-id : Contains the flash chip's device id (1 byte). + +For ROM compatible devices (and ROM fallback from cfi-flash), the following +additional (optional) property is defined: + + - erase-size : The chip's physical erase block size in bytes. + +The device tree may optionally contain sub-nodes describing partitions of the +address space. See partition.txt for more detail. + +Example: + + flash@ff000000 { + compatible = "amd,am29lv128ml", "cfi-flash"; + reg = ; + bank-width = <4>; + device-width = <1>; + #address-cells = <1>; + #size-cells = <1>; + fs@0 { + label = "fs"; + reg = <0 f80000>; + }; + firmware@f80000 { + label ="firmware"; + reg = ; + read-only; + }; + }; + +Here an example with multiple "reg" tuples: + + flash@f0000000,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "intel,pc48f4400p0vb", "cfi-flash"; + reg = <0 0x00000000 0x02000000 + 0 0x02000000 0x02000000>; + bank-width = <2>; + partition@0 { + label = "test-part1"; + reg = <0 0x04000000>; + }; + }; + +An example using SRAM: + + sram@2,0 { + compatible = "samsung,k6f1616u6a", "mtd-ram"; + reg = <2 0 0x00200000>; + bank-width = <2>; + }; diff --git a/drivers/mtd/Kconfig b/drivers/mtd/Kconfig index 23dff48f08..57e4b867bc 100644 --- a/drivers/mtd/Kconfig +++ b/drivers/mtd/Kconfig @@ -8,6 +8,17 @@ config MTD flash, RAM and similar chips, often used for solid state file systems on embedded devices. +config CFI_FLASH + bool "Enable Driver Model for CFI Flash driver" + depends on MTD + help + The Common Flash Interface specification was developed by Intel, + AMD and other flash manufactures. It provides a universal method + for probing the capabilities of flash devices. If you wish to + support any device that is CFI-compliant, you need to enable this + option. Visit + for more information on CFI. + endmenu source "drivers/mtd/nand/Kconfig" diff --git a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c index fc7a878d59..e3cb59887c 100644 --- a/drivers/mtd/cfi_flash.c +++ b/drivers/mtd/cfi_flash.c @@ -18,6 +18,9 @@ /* #define DEBUG */ #include +#include +#include +#include #include #include #include @@ -47,6 +50,8 @@ * reading and writing ... (yes there is such a Hardware). */ +DECLARE_GLOBAL_DATA_PTR; + static uint flash_offset_cfi[2] = { FLASH_OFFSET_CFI, FLASH_OFFSET_CFI_ALT }; #ifdef CONFIG_FLASH_CFI_MTD static uint flash_verbose = 1; @@ -87,10 +92,36 @@ static u16 cfi_flash_config_reg(int i) int cfi_flash_num_flash_banks = CONFIG_SYS_MAX_FLASH_BANKS_DETECT; #endif +#ifdef CONFIG_CFI_FLASH /* for driver model */ +static void cfi_flash_init_dm(void) +{ + struct udevice *dev; + + cfi_flash_num_flash_banks = 0; + /* + * The uclass_first_device() will probe the first device and + * uclass_next_device() will probe the rest if they exist. So + * that cfi_flash_probe() will get called assigning the base + * addresses that are available. + */ + for (uclass_first_device(UCLASS_MTD, &dev); + dev; + uclass_next_device(&dev)) { + } +} + +static phys_addr_t cfi_flash_base[CFI_MAX_FLASH_BANKS]; + +phys_addr_t cfi_flash_bank_addr(int i) +{ + return cfi_flash_base[i]; +} +#else __weak phys_addr_t cfi_flash_bank_addr(int i) { return ((phys_addr_t [])CONFIG_SYS_FLASH_BANKS_LIST)[i]; } +#endif __weak unsigned long cfi_flash_bank_size(int i) { @@ -2322,6 +2353,10 @@ unsigned long flash_init (void) getenv_f("unlock", s, sizeof(s)); #endif +#ifdef CONFIG_CFI_FLASH /* for driver model */ + cfi_flash_init_dm(); +#endif + /* Init: no FLASHes known */ for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) { flash_info[i].flash_id = FLASH_UNKNOWN; @@ -2398,3 +2433,46 @@ unsigned long flash_init (void) return (size); } + +#ifdef CONFIG_CFI_FLASH /* for driver model */ +static int cfi_flash_probe(struct udevice *dev) +{ + void *blob = (void *)gd->fdt_blob; + int node = dev->of_offset; + const fdt32_t *cell; + phys_addr_t addr; + int parent, addrc, sizec; + int len, idx; + + parent = fdt_parent_offset(blob, node); + of_bus_default_count_cells(blob, parent, &addrc, &sizec); + /* decode regs, there may be multiple reg tuples. */ + cell = fdt_getprop(blob, node, "reg", &len); + if (!cell) + return -ENOENT; + idx = 0; + len /= sizeof(fdt32_t); + while (idx < len) { + addr = fdt_translate_address((void *)blob, + node, cell + idx); + cfi_flash_base[cfi_flash_num_flash_banks++] = addr; + idx += addrc + sizec; + } + gd->bd->bi_flashstart = cfi_flash_base[0]; + + return 0; +} + +static const struct udevice_id cfi_flash_ids[] = { + { .compatible = "cfi-flash" }, + { .compatible = "jedec-flash" }, + {} +}; + +U_BOOT_DRIVER(cfi_flash) = { + .name = "cfi_flash", + .id = UCLASS_MTD, + .of_match = cfi_flash_ids, + .probe = cfi_flash_probe, +}; +#endif /* CONFIG_CFI_FLASH */ -- cgit v1.2.1