From d96f41e0165f1bdc16eacf79ba1654c8f45fa71a Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Wed, 30 Nov 2005 13:06:40 +0100 Subject: Add support for TQM8541/8555 boards, TQM85xx support reworked: - Support for TQM8541/8555 boards added. - Complete rework of TQM8540/8560 support. - Common TQM85xx code now supports all current TQM85xx platforms (TQM8540/8541/8555/8560). - DDR SDRAM size detection added. - CAS latency default values can be overwritten by setting "serial#" to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used. If problems are detected with this non default CAS latency, the defualt values will be used instead. - FLASH size detection added. - Moved FCC ethernet driver initialization behind TSEC driver init -> TSEC is first device. Patch by Stefan Roese, 30 Nov 2005 --- CHANGELOG | 15 ++ MAINTAINERS | 5 + MAKEALL | 2 +- Makefile | 23 ++- board/tqm8540/Makefile | 48 ----- board/tqm8540/config.mk | 29 --- board/tqm8540/init.S | 241 ----------------------- board/tqm8540/tqm8540.c | 284 ---------------------------- board/tqm8540/u-boot.lds | 149 --------------- board/tqm8560/Makefile | 48 ----- board/tqm8560/config.mk | 29 --- board/tqm8560/init.S | 241 ----------------------- board/tqm8560/tqm8560.c | 439 ------------------------------------------ board/tqm8560/u-boot.lds | 149 --------------- board/tqm85xx/Makefile | 48 +++++ board/tqm85xx/config.mk | 29 +++ board/tqm85xx/init.S | 234 +++++++++++++++++++++++ board/tqm85xx/sdram.c | 226 ++++++++++++++++++++++ board/tqm85xx/tqm85xx.c | 411 ++++++++++++++++++++++++++++++++++++++++ board/tqm85xx/u-boot.lds | 149 +++++++++++++++ include/configs/TQM8540.h | 464 --------------------------------------------- include/configs/TQM8560.h | 473 ---------------------------------------------- include/configs/TQM85xx.h | 452 ++++++++++++++++++++++++++++++++++++++++++++ lib_ppc/board.c | 10 +- net/eth.c | 6 +- 25 files changed, 1600 insertions(+), 2604 deletions(-) delete mode 100644 board/tqm8540/Makefile delete mode 100644 board/tqm8540/config.mk delete mode 100644 board/tqm8540/init.S delete mode 100644 board/tqm8540/tqm8540.c delete mode 100644 board/tqm8540/u-boot.lds delete mode 100644 board/tqm8560/Makefile delete mode 100644 board/tqm8560/config.mk delete mode 100644 board/tqm8560/init.S delete mode 100644 board/tqm8560/tqm8560.c delete mode 100644 board/tqm8560/u-boot.lds create mode 100644 board/tqm85xx/Makefile create mode 100644 board/tqm85xx/config.mk create mode 100644 board/tqm85xx/init.S create mode 100644 board/tqm85xx/sdram.c create mode 100644 board/tqm85xx/tqm85xx.c create mode 100644 board/tqm85xx/u-boot.lds delete mode 100644 include/configs/TQM8540.h delete mode 100644 include/configs/TQM8560.h create mode 100644 include/configs/TQM85xx.h diff --git a/CHANGELOG b/CHANGELOG index d038fb4f4b..2a41c2e7bb 100644 --- a/CHANGELOG +++ b/CHANGELOG @@ -2,6 +2,21 @@ Changes for U-Boot 1.1.4: ====================================================================== +* Add support for TQM8541/8555 boards, TQM85xx support reworked: + - Support for TQM8541/8555 boards added. + - Complete rework of TQM8540/8560 support. + - Common TQM85xx code now supports all current TQM85xx platforms + (TQM8540/8541/8555/8560). + - DDR SDRAM size detection added. + - CAS latency default values can be overwritten by setting "serial#" + to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used. + If problems are detected with this non default CAS latency, + the defualt values will be used instead. + - FLASH size detection added. + - Moved FCC ethernet driver initialization behind TSEC driver init + -> TSEC is first device. + Patch by Stefan Roese, 30 Nov 2005 + * Add support for AMCC 440SP, add support for AMCC Luan 440SP eval board. Patch by John Otken, 23 Nov 2005 diff --git a/MAINTAINERS b/MAINTAINERS index 845f4e7514..0ef9e0349a 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -274,10 +274,15 @@ Daniel Poirot Stefan Roese + uc100 MPC857 + + TQM85xx MPC8540/8541/8555/8560 + bamboo PPC440EP bunbinga PPC405EP ebony PPC440GP ocotea PPC440GX + p3p440 PPC440GP sycamore PPC405GPr walnut PPC405GP yellowstone PPC440GR diff --git a/MAKEALL b/MAKEALL index 64bec8a1ed..fcbab47cab 100755 --- a/MAKEALL +++ b/MAKEALL @@ -128,7 +128,7 @@ LIST_85xx=" \ MPC8540ADS MPC8540EVAL MPC8541CDS MPC8548CDS \ MPC8555CDS MPC8560ADS PM854 PM856 \ sbc8540 sbc8560 stxgp3 TQM8540 \ - TQM8560 \ + TQM8541 TQM8555 TQM8560 \ " ######################################################################### diff --git a/Makefile b/Makefile index 5d65927b87..dde111c3a6 100644 --- a/Makefile +++ b/Makefile @@ -1325,11 +1325,24 @@ sbc8560_66_config: unconfig stxgp3_config: unconfig @./mkconfig $(@:_config=) ppc mpc85xx stxgp3 -TQM8540_config: unconfig - @./mkconfig $(@:_config=) ppc mpc85xx tqm8540 - -TQM8560_config: unconfig - @./mkconfig $(@:_config=) ppc mpc85xx tqm8560 +TQM8540_config \ +TQM8541_config \ +TQM8555_config \ +TQM8560_config: unconfig + @case "$@" in \ + TQM8540_config) CTYPE=8540;; \ + TQM8541_config) CTYPE=8541;; \ + TQM8555_config) CTYPE=8555;; \ + TQM8560_config) CTYPE=8560;; \ + esac; \ + >include/config.h ; \ + echo "... TQM"$${CTYPE}; \ + echo "#define CONFIG_MPC$${CTYPE}">>include/config.h; \ + echo "#define CONFIG_TQM$${CTYPE}">>include/config.h; \ + echo "#define CONFIG_HOSTNAME tqm$${CTYPE}">>include/config.h; \ + echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>include/config.h; \ + echo "#define CFG_BOOTFILE \"bootfile=/tftpboot/tqm$${CTYPE}/uImage\0\"">>include/config.h + @./mkconfig -a TQM85xx ppc mpc85xx tqm85xx ######################################################################### ## 74xx/7xx Systems diff --git a/board/tqm8540/Makefile b/board/tqm8540/Makefile deleted file mode 100644 index 403ad2d839..0000000000 --- a/board/tqm8540/Makefile +++ /dev/null @@ -1,48 +0,0 @@ -# -# (C) Copyright 2001 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = lib$(BOARD).a - -OBJS := $(BOARD).o -SOBJS := init.o -#SOBJS := - -$(LIB): $(OBJS) $(SOBJS) - $(AR) crv $@ $(OBJS) - -clean: - rm -f $(OBJS) $(SOBJS) - -distclean: clean - rm -f $(LIB) core *.bak .depend - -######################################################################### - -.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) - $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ - --include .depend - -######################################################################### diff --git a/board/tqm8540/config.mk b/board/tqm8540/config.mk deleted file mode 100644 index b0ba25fae6..0000000000 --- a/board/tqm8540/config.mk +++ /dev/null @@ -1,29 +0,0 @@ -# Copyright 2004 Freescale Semiconductor. -# Modified by Xianghua Xiao, X.Xiao@motorola.com -# (C) Copyright 2002,Motorola Inc. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -# -# tqm8540 board -# default CCARBAR is at 0xff700000 -# assume U-Boot is less than 256k -# -TEXT_BASE = 0xfffc0000 diff --git a/board/tqm8540/init.S b/board/tqm8540/init.S deleted file mode 100644 index d9f4d8f96c..0000000000 --- a/board/tqm8540/init.S +++ /dev/null @@ -1,241 +0,0 @@ -/* - * Copyright 2004 Freescale Semiconductor. - * Copyright (C) 2002,2003, Motorola Inc. - * Xianghua Xiao - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - - -/* - * TLB0 and TLB1 Entries - * - * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. - * However, CCSRBAR is then relocated to CFG_CCSRBAR right after - * these TLB entries are established. - * - * The TLB entries for DDR are dynamically setup in spd_sdram() - * and use TLB1 Entries 8 through 15 as needed according to the - * size of DDR memory. - * - * MAS0: tlbsel, esel, nv - * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e - * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr - */ - -#define entry_start \ - mflr r1 ; \ - bl 0f ; - -#define entry_end \ -0: mflr r0 ; \ - mtlr r1 ; \ - blr ; - - - .section .bootpg, "ax" - .globl tlb1_entry -tlb1_entry: - entry_start - - /* - * Number of TLB0 and TLB1 entries in the following table - */ - .long 13 - - /* - * TLB0 16K Cacheable, non-guarded - * 0xd001_0000 16K Temporary Global data for initialization - * - * Use four 4K TLB0 entries. These entries must be cacheable - * as they provide the bootstrap memory before the memory - * controler and real memory have been configured. - * - * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, - * and must not collide with other TLB0 entries. - */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - - /* - * TLB 0, 1: 32M Non-cacheable, guarded - * 0xfe000000 32M FLASH - * Out of reset this entry is only 4K. - */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 2: 256M Non-cacheable, guarded - * 0x80000000 256M PCI1 MEM First half - */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 3: 256M Non-cacheable, guarded - * 0x90000000 256M PCI1 MEM Second half - */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 4: 256M Non-cacheable, guarded - * 0xc0000000 256M Rapid IO MEM First half - */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 5: 256M Non-cacheable, guarded - * 0xd0000000 256M Rapid IO MEM Second half - */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 6: 64M Non-cacheable, guarded - * 0xe000_0000 1M CCSRBAR - * 0xe200_0000 16M PCI1 IO - */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) - -#if !defined(CONFIG_SPD_EEPROM) - /* - * TLB 7: 256M DDR - * 0x00000000 256M DDR System memory - * Without SPD EEPROM configured DDR, this must be setup manually. - * Make sure the TLB count at the top of this table is correct. - * Likely it needs to be increased by two for these entries. - */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) - .long TLB1_MAS0(1, 8, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,1,0,1,0,1) -#endif - - entry_end - -/* - * LAW(Local Access Window) configuration: - * - * 0x0000_0000 0x7fff_ffff DDR 2G - * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M - * 0xc000_0000 0xdfff_ffff RapidIO 512M - * 0xe000_0000 0xe000_ffff CCSR 1M - * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M - * 0xf800_0000 0xf80f_ffff BCSR 1M - * 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M - * - * Notes: - * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. - * If flash is 8M at default position (last 8M), no LAW needed. - */ - -#if !defined(CONFIG_SPD_EEPROM) -#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff) -#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M)) -#else -#define LAWBAR0 0 -#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN) -#endif - -#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff) -#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M)) - -#define LAWBAR2 ((CFG_LBC_FLASH_BASE>>12) & 0xfffff) -#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M)) - -#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff) -#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M)) - -/* - * Rapid IO at 0xc000_0000 for 512 M - */ -#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff) -#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M)) - - - .section .bootpg, "ax" - .globl law_entry -law_entry: - entry_start - .long 0x05 - .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3 - .long LAWBAR4,LAWAR4 - entry_end diff --git a/board/tqm8540/tqm8540.c b/board/tqm8540/tqm8540.c deleted file mode 100644 index 970c6841fd..0000000000 --- a/board/tqm8540/tqm8540.c +++ /dev/null @@ -1,284 +0,0 @@ -/* - * Copyright 2005 DENX Software Engineering - * Copyright 2004 Freescale Semiconductor. - * (C) Copyright 2002,2003, Motorola Inc. - * Xianghua Xiao, (X.Xiao@motorola.com) - * - * (C) Copyright 2002 Scott McNutt - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - - -#include -#include -#include -#include -#include - -#if defined(CONFIG_DDR_ECC) -extern void ddr_enable_ecc (unsigned int dram_size); -#endif - -extern long int spd_sdram (void); - -void local_bus_init (void); -long int fixed_sdram (void); - - -int board_early_init_f (void) -{ - return 0; -} - -int checkboard (void) -{ - puts ("Board: TQM8540\n"); - -#ifdef CONFIG_PCI - printf ("PCI1: 32 bit, %d MHz (compiled)\n", - CONFIG_SYS_CLK_FREQ / 1000000); -#else - printf ("PCI1: disabled\n"); -#endif - /* - * Initialize local bus. - */ - local_bus_init (); - - return 0; -} - - -long int initdram (int board_type) -{ - long dram_size = 0; - extern long spd_sdram (void); - volatile immap_t *immap = (immap_t *) CFG_IMMR; - -#if defined(CONFIG_DDR_DLL) - { - volatile ccsr_gur_t *gur= &immap->im_gur; - int i,x; - - x = 10; - - /* - * Work around to stabilize DDR DLL - */ - gur->ddrdllcr = 0x81000000; - asm("sync;isync;msync"); - udelay (200); - while (gur->ddrdllcr != 0x81000100) { - gur->devdisr = gur->devdisr | 0x00010000; - asm("sync;isync;msync"); - for (i=0; idevdisr = gur->devdisr & 0xfff7ffff; - asm("sync;isync;msync"); - x++; - } - } -#endif - -#if defined(CONFIG_SPD_EEPROM) - dram_size = spd_sdram (); -#else - dram_size = fixed_sdram (); -#endif - -#if defined(CONFIG_DDR_ECC) - /* - * Initialize and enable DDR ECC. - */ - ddr_enable_ecc (dram_size); -#endif - - return dram_size; -} - - -/* - * Initialize Local Bus - */ - -void local_bus_init (void) -{ - volatile immap_t *immap = (immap_t *) CFG_IMMR; - volatile ccsr_gur_t *gur = &immap->im_gur; - volatile ccsr_lbc_t *lbc = &immap->im_lbc; - - uint clkdiv; - uint lbc_hz; - sys_info_t sysinfo; - - /* - * Errata LBC11. - * Fix Local Bus clock glitch when DLL is enabled. - * - * If localbus freq is < 66Mhz, DLL bypass mode must be used. - * If localbus freq is > 133Mhz, DLL can be safely enabled. - * Between 66 and 133, the DLL is enabled with an override workaround. - */ - - get_sys_info (&sysinfo); - clkdiv = lbc->lcrr & 0x0f; - lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; - - if (lbc_hz < 66) { - lbc->lcrr = CFG_LBC_LCRR | 0x80000000; /* DLL Bypass */ - lbc->ltedr = 0xa4c80000; /* DK: !!! */ - - } else if (lbc_hz >= 133) { - lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ - - } else { - /* - * On REV1 boards, need to change CLKDIV before enable DLL. - * Default CLKDIV is 8, change it to 4 temporarily. - */ - uint pvr = get_pvr (); - uint temp_lbcdll = 0; - - if (pvr == PVR_85xx_REV1) { - /* FIXME: Justify the high bit here. */ - lbc->lcrr = 0x10000004; - } - - lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ - udelay (200); - - /* - * Sample LBC DLL ctrl reg, upshift it to set the - * override bits. - */ - temp_lbcdll = gur->lbcdllcr; - gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000); - asm ("sync;isync;msync"); - } -} - - -#if defined(CFG_DRAM_TEST) -int testdram (void) -{ - uint *pstart = (uint *) CFG_MEMTEST_START; - uint *pend = (uint *) CFG_MEMTEST_END; - uint *p; - - printf ("SDRAM test phase 1:\n"); - for (p = pstart; p < pend; p++) - *p = 0xaaaaaaaa; - - for (p = pstart; p < pend; p++) { - if (*p != 0xaaaaaaaa) { - printf ("SDRAM test fails at: %08x\n", (uint) p); - return 1; - } - } - - printf ("SDRAM test phase 2:\n"); - for (p = pstart; p < pend; p++) - *p = 0x55555555; - - for (p = pstart; p < pend; p++) { - if (*p != 0x55555555) { - printf ("SDRAM test fails at: %08x\n", (uint) p); - return 1; - } - } - - printf ("SDRAM test passed.\n"); - return 0; -} -#endif - - -#if !defined(CONFIG_SPD_EEPROM) -/************************************************************************* - * fixed sdram init -- doesn't use serial presence detect. - ************************************************************************/ -long int fixed_sdram (void) -{ -#ifndef CFG_RAMBOOT - volatile immap_t *immap = (immap_t *) CFG_IMMR; - volatile ccsr_ddr_t *ddr = &immap->im_ddr; - - ddr->cs0_bnds = CFG_DDR_CS0_BNDS; - ddr->cs0_config = CFG_DDR_CS0_CONFIG; - ddr->timing_cfg_1 = CFG_DDR_TIMING_1; - ddr->timing_cfg_2 = CFG_DDR_TIMING_2; - ddr->sdram_mode = CFG_DDR_MODE; - ddr->sdram_interval = CFG_DDR_INTERVAL; - ddr->err_disable = 0x0000000D; -#if defined (CONFIG_DDR_ECC) - ddr->err_disable = 0x0000000D; - ddr->err_sbe = 0x00ff0000; -#endif - asm ("sync;isync;msync"); - udelay (500); -#if defined (CONFIG_DDR_ECC) - /* Enable ECC checking */ - ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000); -#else - ddr->sdram_cfg = CFG_DDR_CONTROL; -#endif - asm ("sync; isync; msync"); - udelay (500); -#endif - return get_ram_size (0, CFG_SDRAM_SIZE * 1024 * 1024); -} -#endif /* !defined(CONFIG_SPD_EEPROM) */ - - -#if defined(CONFIG_PCI) -/* - * Initialize PCI Devices, report devices found. - */ - -#ifndef CONFIG_PCI_PNP -static struct pci_config_table pci_mpc85xxads_config_table[] = { - {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, - PCI_IDSEL_NUMBER, PCI_ANY_ID, - pci_cfgfunc_config_device, {PCI_ENET0_IOADDR, - PCI_ENET0_MEMADDR, - PCI_COMMAND_MEMORY | - PCI_COMMAND_MASTER}}, - {} -}; -#endif - - -static struct pci_controller hose = { -#ifndef CONFIG_PCI_PNP - config_table:pci_mpc85xxads_config_table, -#endif -}; - -#endif /* CONFIG_PCI */ - - -void pci_init_board (void) -{ -#ifdef CONFIG_PCI - extern void pci_mpc85xx_init (struct pci_controller *hose); - - pci_mpc85xx_init (&hose); -#endif /* CONFIG_PCI */ -} diff --git a/board/tqm8540/u-boot.lds b/board/tqm8540/u-boot.lds deleted file mode 100644 index 4fdf87c8c1..0000000000 --- a/board/tqm8540/u-boot.lds +++ /dev/null @@ -1,149 +0,0 @@ -/* - * (C) Copyright 2002,2003, Motorola,Inc. - * Xianghua Xiao, X.Xiao@motorola.com. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -OUTPUT_ARCH(powerpc) -SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - .resetvec 0xFFFFFFFC : - { - *(.resetvec) - } = 0xffff - - .bootpg 0xFFFFF000 : - { - cpu/mpc85xx/start.o (.bootpg) - board/tqm8540/init.o (.bootpg) - } = 0xffff - - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - cpu/mpc85xx/start.o (.text) - board/tqm8540/init.o (.text) - cpu/mpc85xx/traps.o (.text) - cpu/mpc85xx/interrupts.o (.text) - cpu/mpc85xx/cpu_init.o (.text) - cpu/mpc85xx/cpu.o (.text) - cpu/mpc85xx/speed.o (.text) - cpu/mpc85xx/pci.o (.text) - common/dlmalloc.o (.text) - lib_generic/crc32.o (.text) - lib_ppc/extable.o (.text) - lib_generic/zlib.o (.text) - *(.text) - *(.fixup) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; - __fixup_entries = (. - _FIXUP_TABLE_) >> 2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - __u_boot_cmd_start = .; - .u_boot_cmd : { *(.u_boot_cmd) } - __u_boot_cmd_end = .; - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - } - _end = . ; - PROVIDE (end = .); -} diff --git a/board/tqm8560/Makefile b/board/tqm8560/Makefile deleted file mode 100644 index 403ad2d839..0000000000 --- a/board/tqm8560/Makefile +++ /dev/null @@ -1,48 +0,0 @@ -# -# (C) Copyright 2001 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = lib$(BOARD).a - -OBJS := $(BOARD).o -SOBJS := init.o -#SOBJS := - -$(LIB): $(OBJS) $(SOBJS) - $(AR) crv $@ $(OBJS) - -clean: - rm -f $(OBJS) $(SOBJS) - -distclean: clean - rm -f $(LIB) core *.bak .depend - -######################################################################### - -.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) - $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ - --include .depend - -######################################################################### diff --git a/board/tqm8560/config.mk b/board/tqm8560/config.mk deleted file mode 100644 index 8aab1e2863..0000000000 --- a/board/tqm8560/config.mk +++ /dev/null @@ -1,29 +0,0 @@ -# Copyright 2004 Freescale Semiconductor. -# Modified by Xianghua Xiao, X.Xiao@motorola.com -# (C) Copyright 2002,Motorola Inc. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -# -# tqm8560 board -# default CCARBAR is at 0xff700000 -# assume U-Boot is less than 256k -# -TEXT_BASE = 0xfffc0000 diff --git a/board/tqm8560/init.S b/board/tqm8560/init.S deleted file mode 100644 index d9f4d8f96c..0000000000 --- a/board/tqm8560/init.S +++ /dev/null @@ -1,241 +0,0 @@ -/* - * Copyright 2004 Freescale Semiconductor. - * Copyright (C) 2002,2003, Motorola Inc. - * Xianghua Xiao - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include - - -/* - * TLB0 and TLB1 Entries - * - * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. - * However, CCSRBAR is then relocated to CFG_CCSRBAR right after - * these TLB entries are established. - * - * The TLB entries for DDR are dynamically setup in spd_sdram() - * and use TLB1 Entries 8 through 15 as needed according to the - * size of DDR memory. - * - * MAS0: tlbsel, esel, nv - * MAS1: valid, iprot, tid, ts, tsize - * MAS2: epn, sharen, x0, x1, w, i, m, g, e - * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr - */ - -#define entry_start \ - mflr r1 ; \ - bl 0f ; - -#define entry_end \ -0: mflr r0 ; \ - mtlr r1 ; \ - blr ; - - - .section .bootpg, "ax" - .globl tlb1_entry -tlb1_entry: - entry_start - - /* - * Number of TLB0 and TLB1 entries in the following table - */ - .long 13 - - /* - * TLB0 16K Cacheable, non-guarded - * 0xd001_0000 16K Temporary Global data for initialization - * - * Use four 4K TLB0 entries. These entries must be cacheable - * as they provide the bootstrap memory before the memory - * controler and real memory have been configured. - * - * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, - * and must not collide with other TLB0 entries. - */ - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - .long TLB1_MAS0(0, 0, 0) - .long TLB1_MAS1(1, 0, 0, 0, 0) - .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), - 0,0,0,0,0,1,0,1,0,1) - - - /* - * TLB 0, 1: 32M Non-cacheable, guarded - * 0xfe000000 32M FLASH - * Out of reset this entry is only 4K. - */ - .long TLB1_MAS0(1, 1, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) - .long TLB1_MAS0(1, 0, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 2: 256M Non-cacheable, guarded - * 0x80000000 256M PCI1 MEM First half - */ - .long TLB1_MAS0(1, 2, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 3: 256M Non-cacheable, guarded - * 0x90000000 256M PCI1 MEM Second half - */ - .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 4: 256M Non-cacheable, guarded - * 0xc0000000 256M Rapid IO MEM First half - */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 5: 256M Non-cacheable, guarded - * 0xd0000000 256M Rapid IO MEM Second half - */ - .long TLB1_MAS0(1, 5, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) - - /* - * TLB 6: 64M Non-cacheable, guarded - * 0xe000_0000 1M CCSRBAR - * 0xe200_0000 16M PCI1 IO - */ - .long TLB1_MAS0(1, 6, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) - -#if !defined(CONFIG_SPD_EEPROM) - /* - * TLB 7: 256M DDR - * 0x00000000 256M DDR System memory - * Without SPD EEPROM configured DDR, this must be setup manually. - * Make sure the TLB count at the top of this table is correct. - * Likely it needs to be increased by two for these entries. - */ - .long TLB1_MAS0(1, 7, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) - .long TLB1_MAS0(1, 8, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,0,0,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,1,0,1,0,1) -#endif - - entry_end - -/* - * LAW(Local Access Window) configuration: - * - * 0x0000_0000 0x7fff_ffff DDR 2G - * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M - * 0xc000_0000 0xdfff_ffff RapidIO 512M - * 0xe000_0000 0xe000_ffff CCSR 1M - * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M - * 0xf800_0000 0xf80f_ffff BCSR 1M - * 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M - * - * Notes: - * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. - * If flash is 8M at default position (last 8M), no LAW needed. - */ - -#if !defined(CONFIG_SPD_EEPROM) -#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff) -#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M)) -#else -#define LAWBAR0 0 -#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN) -#endif - -#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff) -#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M)) - -#define LAWBAR2 ((CFG_LBC_FLASH_BASE>>12) & 0xfffff) -#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M)) - -#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff) -#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M)) - -/* - * Rapid IO at 0xc000_0000 for 512 M - */ -#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff) -#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M)) - - - .section .bootpg, "ax" - .globl law_entry -law_entry: - entry_start - .long 0x05 - .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3 - .long LAWBAR4,LAWAR4 - entry_end diff --git a/board/tqm8560/tqm8560.c b/board/tqm8560/tqm8560.c deleted file mode 100644 index 71f58805bc..0000000000 --- a/board/tqm8560/tqm8560.c +++ /dev/null @@ -1,439 +0,0 @@ -/* - * Copyright 2005 DENX Software Engineering - * Copyright 2004 Freescale Semiconductor. - * (C) Copyright 2002,2003, Motorola Inc. - * Xianghua Xiao, (X.Xiao@motorola.com) - * - * (C) Copyright 2002 Scott McNutt - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - - -#include -#include -#include -#include -#include -#include - -#if defined(CONFIG_DDR_ECC) -extern void ddr_enable_ecc (unsigned int dram_size); -#endif - -extern long int spd_sdram (void); - -void local_bus_init (void); -long int fixed_sdram (void); - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */ - /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */ - /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */ - /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */ - /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */ - /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */ - /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ - /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ - /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ - /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ - /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ - /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ - /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ - /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ - /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */ - /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */ - /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */ - /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */ - /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */ - /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */ - /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */ - /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */ - /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */ - /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */ - /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ - /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */ - /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ - /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ - /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ - /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ - /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* FREERUN */ - /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ - }, - - /* Port B configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 0, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */ - /* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */ - /* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */ - /* PB14 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */ - /* PB13 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:COL */ - /* PB12 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:CRS */ - /* PB11 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB10 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB9 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB8 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ - /* PB7 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB6 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB5 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB4 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ - /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ - /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ - /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ - /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */ - /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ - /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ - /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ - /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ - /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ - /* PC21 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ - /* PC20 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ - /* PC19 */ { 0, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */ - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */ - /* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* PC17 */ - /* PC16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */ - /* PC15 */ { 0, 1, 0, 0, 0, 0 }, /* PC15 */ - /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ - /* PC13 */ { 0, 1, 0, 0, 0, 0 }, /* PC13 */ - /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */ - /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */ - /* PC10 */ { 0, 0, 0, 1, 0, 0 }, /* FETHMDC */ - /* PC9 */ { 0, 0, 0, 0, 0, 0 }, /* FETHMDIO */ - /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ - /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ - /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ - /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ - /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ - /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ - /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ - /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ - /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ - /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ - /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ - /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* PD28 */ - /* PD27 */ { 1, 1, 0, 1, 0, 0 }, /* PD27 */ - /* PD26 */ { 1, 1, 0, 1, 0, 0 }, /* PD26 */ - /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ - /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ - /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ - /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ - /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ - /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ - /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ - /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ - /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ - /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */ - /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ - /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ - /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ - /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - - -int board_early_init_f (void) -{ - return 0; -} - -int checkboard (void) -{ - puts ("Board: TQM8560\n"); - -#ifdef CONFIG_PCI - printf ("PCI1: 32 bit, %d MHz (compiled)\n", - CONFIG_SYS_CLK_FREQ / 1000000); -#else - printf ("PCI1: disabled\n"); -#endif - /* - * Initialize local bus. - */ - local_bus_init (); - - return 0; -} - - -long int initdram (int board_type) -{ - long dram_size = 0; - extern long spd_sdram (void); - volatile immap_t *immap = (immap_t *) CFG_IMMR; - -#if defined(CONFIG_DDR_DLL) - { - volatile ccsr_gur_t *gur= &immap->im_gur; - int i,x; - - x = 10; - - /* - * Work around to stabilize DDR DLL - */ - gur->ddrdllcr = 0x81000000; - asm("sync;isync;msync"); - udelay (200); - while (gur->ddrdllcr != 0x81000100) { - gur->devdisr = gur->devdisr | 0x00010000; - asm("sync;isync;msync"); - for (i=0; idevdisr = gur->devdisr & 0xfff7ffff; - asm("sync;isync;msync"); - x++; - } - } -#endif - -#if defined(CONFIG_SPD_EEPROM) - dram_size = spd_sdram (); -#else - dram_size = fixed_sdram (); -#endif - -#if defined(CONFIG_DDR_ECC) - /* - * Initialize and enable DDR ECC. - */ - ddr_enable_ecc (dram_size); -#endif - - return dram_size; -} - - -/* - * Initialize Local Bus - */ - -void local_bus_init (void) -{ - volatile immap_t *immap = (immap_t *) CFG_IMMR; - volatile ccsr_gur_t *gur = &immap->im_gur; - volatile ccsr_lbc_t *lbc = &immap->im_lbc; - - uint clkdiv; - uint lbc_hz; - sys_info_t sysinfo; - - /* - * Errata LBC11. - * Fix Local Bus clock glitch when DLL is enabled. - * - * If localbus freq is < 66Mhz, DLL bypass mode must be used. - * If localbus freq is > 133Mhz, DLL can be safely enabled. - * Between 66 and 133, the DLL is enabled with an override workaround. - */ - - get_sys_info (&sysinfo); - clkdiv = lbc->lcrr & 0x0f; - lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; - - if (lbc_hz < 66) { - lbc->lcrr = CFG_LBC_LCRR | 0x80000000; /* DLL Bypass */ - lbc->ltedr = 0xa4c80000; /* DK: !!! */ - - } else if (lbc_hz >= 133) { - lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ - - } else { - /* - * On REV1 boards, need to change CLKDIV before enable DLL. - * Default CLKDIV is 8, change it to 4 temporarily. - */ - uint pvr = get_pvr (); - uint temp_lbcdll = 0; - - if (pvr == PVR_85xx_REV1) { - /* FIXME: Justify the high bit here. */ - lbc->lcrr = 0x10000004; - } - - lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ - udelay (200); - - /* - * Sample LBC DLL ctrl reg, upshift it to set the - * override bits. - */ - temp_lbcdll = gur->lbcdllcr; - gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000); - asm ("sync;isync;msync"); - } -} - - -#if defined(CFG_DRAM_TEST) -int testdram (void) -{ - uint *pstart = (uint *) CFG_MEMTEST_START; - uint *pend = (uint *) CFG_MEMTEST_END; - uint *p; - - printf ("SDRAM test phase 1:\n"); - for (p = pstart; p < pend; p++) - *p = 0xaaaaaaaa; - - for (p = pstart; p < pend; p++) { - if (*p != 0xaaaaaaaa) { - printf ("SDRAM test fails at: %08x\n", (uint) p); - return 1; - } - } - - printf ("SDRAM test phase 2:\n"); - for (p = pstart; p < pend; p++) - *p = 0x55555555; - - for (p = pstart; p < pend; p++) { - if (*p != 0x55555555) { - printf ("SDRAM test fails at: %08x\n", (uint) p); - return 1; - } - } - - printf ("SDRAM test passed.\n"); - return 0; -} -#endif - - -#if !defined(CONFIG_SPD_EEPROM) -/************************************************************************* - * fixed sdram init -- doesn't use serial presence detect. - ************************************************************************/ -long int fixed_sdram (void) -{ -#ifndef CFG_RAMBOOT - volatile immap_t *immap = (immap_t *) CFG_IMMR; - volatile ccsr_ddr_t *ddr = &immap->im_ddr; - - ddr->cs0_bnds = CFG_DDR_CS0_BNDS; - ddr->cs0_config = CFG_DDR_CS0_CONFIG; - ddr->timing_cfg_1 = CFG_DDR_TIMING_1; - ddr->timing_cfg_2 = CFG_DDR_TIMING_2; - ddr->sdram_mode = CFG_DDR_MODE; - ddr->sdram_interval = CFG_DDR_INTERVAL; - ddr->err_disable = 0x0000000D; -#if defined (CONFIG_DDR_ECC) - ddr->err_disable = 0x0000000D; - ddr->err_sbe = 0x00ff0000; -#endif - asm ("sync;isync;msync"); - udelay (500); -#if defined (CONFIG_DDR_ECC) - /* Enable ECC checking */ - ddr->sdram_cfg = (CFG_DDR_CONTROL | 0x20000000); -#else - ddr->sdram_cfg = CFG_DDR_CONTROL; -#endif - asm ("sync; isync; msync"); - udelay (500); -#endif - return get_ram_size (0, CFG_SDRAM_SIZE * 1024 * 1024); -} -#endif /* !defined(CONFIG_SPD_EEPROM) */ - - -#if defined(CONFIG_PCI) -/* - * Initialize PCI Devices, report devices found. - */ - -#ifndef CONFIG_PCI_PNP -static struct pci_config_table pci_mpc85xxads_config_table[] = { - {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, - PCI_IDSEL_NUMBER, PCI_ANY_ID, - pci_cfgfunc_config_device, {PCI_ENET0_IOADDR, - PCI_ENET0_MEMADDR, - PCI_COMMAND_MEMORY | - PCI_COMMAND_MASTER}}, - {} -}; -#endif - - -static struct pci_controller hose = { -#ifndef CONFIG_PCI_PNP - config_table:pci_mpc85xxads_config_table, -#endif -}; - -#endif /* CONFIG_PCI */ - - -void pci_init_board (void) -{ -#ifdef CONFIG_PCI - extern void pci_mpc85xx_init (struct pci_controller *hose); - - pci_mpc85xx_init (&hose); -#endif /* CONFIG_PCI */ -} diff --git a/board/tqm8560/u-boot.lds b/board/tqm8560/u-boot.lds deleted file mode 100644 index 6f9240b918..0000000000 --- a/board/tqm8560/u-boot.lds +++ /dev/null @@ -1,149 +0,0 @@ -/* - * (C) Copyright 2002,2003, Motorola,Inc. - * Xianghua Xiao, X.Xiao@motorola.com. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -OUTPUT_ARCH(powerpc) -SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); -/* Do we need any of these for elf? - __DYNAMIC = 0; */ -SECTIONS -{ - .resetvec 0xFFFFFFFC : - { - *(.resetvec) - } = 0xffff - - .bootpg 0xFFFFF000 : - { - cpu/mpc85xx/start.o (.bootpg) - board/tqm8560/init.o (.bootpg) - } = 0xffff - - /* Read-only sections, merged into text segment: */ - . = + SIZEOF_HEADERS; - .interp : { *(.interp) } - .hash : { *(.hash) } - .dynsym : { *(.dynsym) } - .dynstr : { *(.dynstr) } - .rel.text : { *(.rel.text) } - .rela.text : { *(.rela.text) } - .rel.data : { *(.rel.data) } - .rela.data : { *(.rela.data) } - .rel.rodata : { *(.rel.rodata) } - .rela.rodata : { *(.rela.rodata) } - .rel.got : { *(.rel.got) } - .rela.got : { *(.rela.got) } - .rel.ctors : { *(.rel.ctors) } - .rela.ctors : { *(.rela.ctors) } - .rel.dtors : { *(.rel.dtors) } - .rela.dtors : { *(.rela.dtors) } - .rel.bss : { *(.rel.bss) } - .rela.bss : { *(.rela.bss) } - .rel.plt : { *(.rel.plt) } - .rela.plt : { *(.rela.plt) } - .init : { *(.init) } - .plt : { *(.plt) } - .text : - { - cpu/mpc85xx/start.o (.text) - board/tqm8560/init.o (.text) - cpu/mpc85xx/traps.o (.text) - cpu/mpc85xx/interrupts.o (.text) - cpu/mpc85xx/cpu_init.o (.text) - cpu/mpc85xx/cpu.o (.text) - cpu/mpc85xx/speed.o (.text) - cpu/mpc85xx/pci.o (.text) - common/dlmalloc.o (.text) - lib_generic/crc32.o (.text) - lib_ppc/extable.o (.text) - lib_generic/zlib.o (.text) - *(.text) - *(.fixup) - *(.got1) - } - _etext = .; - PROVIDE (etext = .); - .rodata : - { - *(.rodata) - *(.rodata1) - *(.rodata.str1.4) - } - .fini : { *(.fini) } =0 - .ctors : { *(.ctors) } - .dtors : { *(.dtors) } - - /* Read-write section, merged into data segment: */ - . = (. + 0x00FF) & 0xFFFFFF00; - _erotext = .; - PROVIDE (erotext = .); - .reloc : - { - *(.got) - _GOT2_TABLE_ = .; - *(.got2) - _FIXUP_TABLE_ = .; - *(.fixup) - } - __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; - __fixup_entries = (. - _FIXUP_TABLE_) >> 2; - - .data : - { - *(.data) - *(.data1) - *(.sdata) - *(.sdata2) - *(.dynamic) - CONSTRUCTORS - } - _edata = .; - PROVIDE (edata = .); - - . = .; - __u_boot_cmd_start = .; - .u_boot_cmd : { *(.u_boot_cmd) } - __u_boot_cmd_end = .; - - . = .; - __start___ex_table = .; - __ex_table : { *(__ex_table) } - __stop___ex_table = .; - - . = ALIGN(256); - __init_begin = .; - .text.init : { *(.text.init) } - .data.init : { *(.data.init) } - . = ALIGN(256); - __init_end = .; - - __bss_start = .; - .bss : - { - *(.sbss) *(.scommon) - *(.dynbss) - *(.bss) - *(COMMON) - } - _end = . ; - PROVIDE (end = .); -} diff --git a/board/tqm85xx/Makefile b/board/tqm85xx/Makefile new file mode 100644 index 0000000000..3933d46f0c --- /dev/null +++ b/board/tqm85xx/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2001 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = lib$(BOARD).a + +OBJS := $(BOARD).o sdram.o +SOBJS := init.o +#SOBJS := + +$(LIB): $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +.depend: Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c) + $(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@ + +-include .depend + +######################################################################### diff --git a/board/tqm85xx/config.mk b/board/tqm85xx/config.mk new file mode 100644 index 0000000000..52e84ad772 --- /dev/null +++ b/board/tqm85xx/config.mk @@ -0,0 +1,29 @@ +# Copyright 2004 Freescale Semiconductor. +# Modified by Xianghua Xiao, X.Xiao@motorola.com +# (C) Copyright 2002,Motorola Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# tqm85xx board +# default CCARBAR is at 0xff700000 +# assume U-Boot is less than 256k +# +TEXT_BASE = 0xfffc0000 diff --git a/board/tqm85xx/init.S b/board/tqm85xx/init.S new file mode 100644 index 0000000000..1f610385e6 --- /dev/null +++ b/board/tqm85xx/init.S @@ -0,0 +1,234 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * Copyright (C) 2002,2003, Motorola Inc. + * Xianghua Xiao + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include +#include +#include +#include +#include +#include + + +/* + * TLB0 and TLB1 Entries + * + * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. + * However, CCSRBAR is then relocated to CFG_CCSRBAR right after + * these TLB entries are established. + * + * The TLB entries for DDR are dynamically setup in spd_sdram() + * and use TLB1 Entries 8 through 15 as needed according to the + * size of DDR memory. + * + * MAS0: tlbsel, esel, nv + * MAS1: valid, iprot, tid, ts, tsize + * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr + */ + +#define entry_start \ + mflr r1 ; \ + bl 0f ; + +#define entry_end \ +0: mflr r0 ; \ + mtlr r1 ; \ + blr ; + + + .section .bootpg, "ax" + .globl tlb1_entry +tlb1_entry: + entry_start + + /* + * Number of TLB0 and TLB1 entries in the following table + */ + .long 13 + + /* + * TLB0 16K Cacheable, non-guarded + * 0xd001_0000 16K Temporary Global data for initialization + * + * Use four 4K TLB0 entries. These entries must be cacheable + * as they provide the bootstrap memory before the memory + * controler and real memory have been configured. + * + * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, + * and must not collide with other TLB0 entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + + /* + * TLB 0, 1: 128M Non-cacheable, guarded + * 0xf8000000 128M FLASH + * Out of reset this entry is only 4K. + */ + .long TLB1_MAS0(1, 1, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + .long TLB1_MAS0(1, 0, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x4000000), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x4000000), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 2: 256M Non-cacheable, guarded + * 0x80000000 256M PCI1 MEM First half + */ + .long TLB1_MAS0(1, 2, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 3: 256M Non-cacheable, guarded + * 0x90000000 256M PCI1 MEM Second half + */ + .long TLB1_MAS0(1, 3, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 4: 256M Non-cacheable, guarded + * 0xc0000000 256M Rapid IO MEM First half + */ + .long TLB1_MAS0(1, 4, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 5: 256M Non-cacheable, guarded + * 0xd0000000 256M Rapid IO MEM Second half + */ + .long TLB1_MAS0(1, 5, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 6: 64M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + * 0xe200_0000 16M PCI1 IO + */ + .long TLB1_MAS0(1, 6, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 7+8: 512M DDR, cache disabled (needed for memory test) + * 0x00000000 512M DDR System memory + * Without SPD EEPROM configured DDR, this must be setup manually. + * Make sure the TLB count at the top of this table is correct. + * Likely it needs to be increased by two for these entries. + */ + .long TLB1_MAS0(1, 7, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long TLB1_MAS0(1, 8, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE+0x10000000), 0,0,0,0,0,1,0,1,0,1) + + entry_end + +/* + * LAW(Local Access Window) configuration: + * + * 0x0000_0000 0x7fff_ffff DDR 2G + * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M + * 0xc000_0000 0xdfff_ffff RapidIO 512M + * 0xe000_0000 0xe000_ffff CCSR 1M + * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M + * 0xf800_0000 0xf80f_ffff BCSR 1M + * 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M + * + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + */ + +#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff) +#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_512M)) + +#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff) +#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M)) + +#define LAWBAR2 ((CFG_LBC_FLASH_BASE>>12) & 0xfffff) +#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_128M)) + +#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M)) + +/* + * Rapid IO at 0xc000_0000 for 512 M + */ +#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff) +#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M)) + + + .section .bootpg, "ax" + .globl law_entry +law_entry: + entry_start + .long 0x05 + .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3 + .long LAWBAR4,LAWAR4 + entry_end diff --git a/board/tqm85xx/sdram.c b/board/tqm85xx/sdram.c new file mode 100644 index 0000000000..9c1f087687 --- /dev/null +++ b/board/tqm85xx/sdram.c @@ -0,0 +1,226 @@ +/* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#include +#include +#include +#include +#include +#include + +struct sdram_conf_s { + unsigned long size; + unsigned long reg; +}; + +typedef struct sdram_conf_s sdram_conf_t; + +sdram_conf_t ddr_cs_conf[] = { + {(512 << 20), 0x80000202}, /* 512MB, 14x10(4) */ + {(256 << 20), 0x80000102}, /* 256MB, 13x10(4) */ + {(128 << 20), 0x80000101}, /* 128MB, 13x9(4) */ + {(64 << 20), 0x80000001}, /* 64MB, 12x9(4) */ +}; + +#define N_DDR_CS_CONF (sizeof(ddr_cs_conf) / sizeof(ddr_cs_conf[0])) + +int cas_latency(void); + +/* + * Autodetect onboard DDR SDRAM on 85xx platforms + * + * NOTE: Some of the hardcoded values are hardware dependant, + * so this should be extended for other future boards + * using this routine! + */ +long int sdram_setup(int casl) +{ + int i; + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile ccsr_ddr_t *ddr = &immap->im_ddr; + unsigned long cfg_ddr_timing1; + unsigned long cfg_ddr_mode; + + /* + * Disable memory controller. + */ + ddr->cs0_config = 0; + ddr->sdram_cfg = 0; + + switch (casl) { + case 20: + cfg_ddr_timing1 = 0x47405331 | (3 << 16); + cfg_ddr_mode = 0x40020002 | (2 << 4); + break; + + case 25: + cfg_ddr_timing1 = 0x47405331 | (4 << 16); + cfg_ddr_mode = 0x40020002 | (6 << 4); + break; + + case 30: + default: + cfg_ddr_timing1 = 0x47405331 | (5 << 16); + cfg_ddr_mode = 0x40020002 | (3 << 4); + break; + } + + ddr->cs0_bnds = (ddr_cs_conf[0].size - 1) >> 24; + ddr->cs0_config = ddr_cs_conf[0].reg; + ddr->timing_cfg_1 = cfg_ddr_timing1; + ddr->timing_cfg_2 = 0x00000800; /* P9-45,may need tuning */ + ddr->sdram_mode = cfg_ddr_mode; + ddr->sdram_interval = 0x05160100; /* autocharge,no open page */ + ddr->err_disable = 0x0000000D; + + asm ("sync;isync;msync"); + udelay(1000); + + ddr->sdram_cfg = 0xc2000000; /* unbuffered,no DYN_PWR */ + asm ("sync; isync; msync"); + udelay(1000); + + for (i=0; ics0_config = ddr_cs_conf[i].reg; + + if (get_ram_size(0, ddr_cs_conf[i].size) == ddr_cs_conf[i].size) { + /* + * OK, size detected -> all done + */ + return ddr_cs_conf[i].size; + } + } + + return 0; /* nothing found ! */ +} + +void board_add_ram_info(int use_default) +{ + int casl; + + if (use_default) + casl = CONFIG_DDR_DEFAULT_CL; + else + casl = cas_latency(); + + puts(" (CL="); + switch (casl) { + case 20: + puts("2)"); + break; + + case 25: + puts("2.5)"); + break; + + case 30: + puts("3)"); + break; + } +} + +long int initdram (int board_type) +{ + long dram_size = 0; + int casl; + +#if defined(CONFIG_DDR_DLL) + /* + * This DLL-Override only used on TQM8540 and TQM8560 + */ + { + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile ccsr_gur_t *gur= &immap->im_gur; + int i,x; + + x = 10; + + /* + * Work around to stabilize DDR DLL + */ + gur->ddrdllcr = 0x81000000; + asm("sync;isync;msync"); + udelay (200); + while (gur->ddrdllcr != 0x81000100) { + gur->devdisr = gur->devdisr | 0x00010000; + asm("sync;isync;msync"); + for (i=0; idevdisr = gur->devdisr & 0xfff7ffff; + asm("sync;isync;msync"); + x++; + } + } +#endif + + casl = cas_latency(); + dram_size = sdram_setup(casl); + if ((dram_size == 0) && (casl != CONFIG_DDR_DEFAULT_CL)) { + /* + * Try again with default CAS latency + */ + puts("Problem with CAS lantency"); + board_add_ram_info(1); + puts(", using default CL!\n"); + casl = CONFIG_DDR_DEFAULT_CL; + dram_size = sdram_setup(casl); + puts(" "); + } + + return dram_size; +} + +#if defined(CFG_DRAM_TEST) +int testdram (void) +{ + uint *pstart = (uint *) CFG_MEMTEST_START; + uint *pend = (uint *) CFG_MEMTEST_END; + uint *p; + + printf ("SDRAM test phase 1:\n"); + for (p = pstart; p < pend; p++) + *p = 0xaaaaaaaa; + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { + printf ("SDRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf ("SDRAM test phase 2:\n"); + for (p = pstart; p < pend; p++) + *p = 0x55555555; + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { + printf ("SDRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf ("SDRAM test passed.\n"); + return 0; +} +#endif diff --git a/board/tqm85xx/tqm85xx.c b/board/tqm85xx/tqm85xx.c new file mode 100644 index 0000000000..13ea6f48dd --- /dev/null +++ b/board/tqm85xx/tqm85xx.c @@ -0,0 +1,411 @@ +/* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Copyright 2004 Freescale Semiconductor. + * (C) Copyright 2002,2003, Motorola Inc. + * Xianghua Xiao, (X.Xiao@motorola.com) + * + * (C) Copyright 2002 Scott McNutt + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#include +#include +#include +#include +#include +#include +#include + +extern flash_info_t flash_info[]; /* FLASH chips info */ + +void local_bus_init (void); +long int fixed_sdram (void); +ulong flash_get_size (ulong base, int banknum); + +#ifdef CONFIG_CPM2 +/* + * I/O Port configuration table + * + * if conf is 1, then that port pin will be configured at boot time + * according to the five values podr/pdir/ppar/psor/pdat for that entry + */ + +const iop_conf_t iop_conf_tab[4][32] = { + + /* Port A configuration */ + { /* conf ppar psor pdir podr pdat */ + /* PA31 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII COL */ + /* PA30 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII CRS */ + /* PA29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_ER */ + /* PA28 */ { 1, 1, 1, 1, 0, 0 }, /* FCC1 MII TX_EN */ + /* PA27 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_DV */ + /* PA26 */ { 1, 1, 1, 0, 0, 0 }, /* FCC1 MII RX_ER */ + /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ + /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ + /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ + /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ + /* PA21 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[3] */ + /* PA20 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[2] */ + /* PA19 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[1] */ + /* PA18 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 MII TxD[0] */ + /* PA17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[0] */ + /* PA16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[1] */ + /* PA15 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[2] */ + /* PA14 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 MII RxD[3] */ + /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */ + /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */ + /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */ + /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */ + /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* FCC1 L1TXD */ + /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* FCC1 L1RXD */ + /* PA7 */ { 0, 0, 0, 1, 0, 0 }, /* PA7 */ + /* PA6 */ { 0, 1, 1, 1, 0, 0 }, /* TDM A1 L1RSYNC */ + /* PA5 */ { 0, 0, 0, 1, 0, 0 }, /* PA5 */ + /* PA4 */ { 0, 0, 0, 1, 0, 0 }, /* PA4 */ + /* PA3 */ { 0, 0, 0, 1, 0, 0 }, /* PA3 */ + /* PA2 */ { 0, 0, 0, 1, 0, 0 }, /* PA2 */ + /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* FREERUN */ + /* PA0 */ { 0, 0, 0, 1, 0, 0 } /* PA0 */ + }, + + /* Port B configuration */ + { /* conf ppar psor pdir podr pdat */ + /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ + /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ + /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ + /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ + /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ + /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ + /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ + /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ + /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ + /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ + /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ + /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ + /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ + /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ + /* PB17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */ + /* PB16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */ + /* PB15 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */ + /* PB14 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */ + /* PB13 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:COL */ + /* PB12 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:CRS */ + /* PB11 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB10 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB9 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB8 */ { 1, 1, 0, 0, 0, 0 }, /* FCC3:RXD */ + /* PB7 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB6 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB5 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB4 */ { 1, 1, 0, 1, 0, 0 }, /* FCC3:TXD */ + /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ + }, + + /* Port C */ + { /* conf ppar psor pdir podr pdat */ + /* PC31 */ { 0, 0, 0, 1, 0, 0 }, /* PC31 */ + /* PC30 */ { 0, 0, 0, 1, 0, 0 }, /* PC30 */ + /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ + /* PC28 */ { 0, 0, 0, 1, 0, 0 }, /* PC28 */ + /* PC27 */ { 0, 0, 0, 1, 0, 0 }, /* UART Clock in */ + /* PC26 */ { 0, 0, 0, 1, 0, 0 }, /* PC26 */ + /* PC25 */ { 0, 0, 0, 1, 0, 0 }, /* PC25 */ + /* PC24 */ { 0, 0, 0, 1, 0, 0 }, /* PC24 */ + /* PC23 */ { 0, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ + /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ + /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ + /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ + /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK CLK13 */ + /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK14) */ + /* PC17 */ { 1, 1, 0, 0, 0, 0 }, /* PC17 */ + /* PC16 */ { 1, 1, 0, 0, 0, 0 }, /* FCC Tx Clock (CLK16) */ + /* PC15 */ { 0, 1, 0, 0, 0, 0 }, /* PC15 */ + /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ + /* PC13 */ { 0, 1, 0, 0, 0, 0 }, /* PC13 */ + /* PC12 */ { 0, 1, 0, 1, 0, 0 }, /* PC12 */ + /* PC11 */ { 0, 0, 0, 1, 0, 0 }, /* LXT971 transmit control */ + /* PC10 */ { 0, 0, 0, 1, 0, 0 }, /* FETHMDC */ + /* PC9 */ { 0, 0, 0, 0, 0, 0 }, /* FETHMDIO */ + /* PC8 */ { 0, 0, 0, 1, 0, 0 }, /* PC8 */ + /* PC7 */ { 0, 0, 0, 1, 0, 0 }, /* PC7 */ + /* PC6 */ { 0, 0, 0, 1, 0, 0 }, /* PC6 */ + /* PC5 */ { 0, 0, 0, 1, 0, 0 }, /* PC5 */ + /* PC4 */ { 0, 0, 0, 1, 0, 0 }, /* PC4 */ + /* PC3 */ { 0, 0, 0, 1, 0, 0 }, /* PC3 */ + /* PC2 */ { 0, 0, 0, 1, 0, 1 }, /* ENET FDE */ + /* PC1 */ { 0, 0, 0, 1, 0, 0 }, /* ENET DSQE */ + /* PC0 */ { 0, 0, 0, 1, 0, 0 }, /* ENET LBK */ + }, + + /* Port D */ + { /* conf ppar psor pdir podr pdat */ + /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ + /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ + /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ + /* PD28 */ { 1, 1, 0, 0, 0, 0 }, /* PD28 */ + /* PD27 */ { 1, 1, 0, 1, 0, 0 }, /* PD27 */ + /* PD26 */ { 1, 1, 0, 1, 0, 0 }, /* PD26 */ + /* PD25 */ { 0, 0, 0, 1, 0, 0 }, /* PD25 */ + /* PD24 */ { 0, 0, 0, 1, 0, 0 }, /* PD24 */ + /* PD23 */ { 0, 0, 0, 1, 0, 0 }, /* PD23 */ + /* PD22 */ { 0, 0, 0, 1, 0, 0 }, /* PD22 */ + /* PD21 */ { 0, 0, 0, 1, 0, 0 }, /* PD21 */ + /* PD20 */ { 0, 0, 0, 1, 0, 0 }, /* PD20 */ + /* PD19 */ { 0, 0, 0, 1, 0, 0 }, /* PD19 */ + /* PD18 */ { 0, 0, 0, 1, 0, 0 }, /* PD18 */ + /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ + /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ + /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */ + /* PD14 */ { 0, 0, 0, 1, 0, 0 }, /* LED */ + /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */ + /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */ + /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */ + /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */ + /* PD9 */ { 0, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ + /* PD8 */ { 0, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ + /* PD7 */ { 0, 0, 0, 1, 0, 1 }, /* PD7 */ + /* PD6 */ { 0, 0, 0, 1, 0, 1 }, /* PD6 */ + /* PD5 */ { 0, 0, 0, 1, 0, 1 }, /* PD5 */ + /* PD4 */ { 0, 0, 0, 1, 0, 1 }, /* PD4 */ + /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ + /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ + } +}; +#endif /* CONFIG_CPM2 */ + +#define CASL_STRING1 "casl=xx" +#define CASL_STRING2 "casl=" + +static const int casl_table[] = { 20, 25, 30 }; +#define N_CASL (sizeof(casl_table) / sizeof(casl_table[0])) + +int cas_latency(void) +{ + char *s = getenv("serial#"); + int casl; + int val; + int i; + + casl = CONFIG_DDR_DEFAULT_CL; + + if (s != NULL) { + if (strncmp(s + strlen(s) - strlen(CASL_STRING1), CASL_STRING2, + strlen(CASL_STRING2)) == 0) { + val = simple_strtoul(s + strlen(s) - 2, NULL, 10); + + for (i=0; iim_lbc; + + /* + * Adjust flash start and offset to detected values + */ + gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize; + gd->bd->bi_flashoffset = 0; + + /* + * Check if boot FLASH isn't max size + */ + if (gd->bd->bi_flashsize < (0 - CFG_FLASH0)) { + memctl->or0 = gd->bd->bi_flashstart | (CFG_OR0_PRELIM & 0x00007fff); + memctl->br0 = gd->bd->bi_flashstart | (CFG_BR0_PRELIM & 0x00007fff); + + /* + * Re-check to get correct base address + */ + flash_get_size(gd->bd->bi_flashstart, CFG_MAX_FLASH_BANKS - 1); + } + + /* + * Check if only one FLASH bank is available + */ + if (gd->bd->bi_flashsize != CFG_MAX_FLASH_BANKS * (0 - CFG_FLASH0)) { + memctl->or1 = 0; + memctl->br1 = 0; + + /* + * Re-do flash protection upon new addresses + */ + flash_protect (FLAG_PROTECT_CLEAR, + gd->bd->bi_flashstart, 0xffffffff, + &flash_info[CFG_MAX_FLASH_BANKS - 1]); + + /* Monitor protection ON by default */ + flash_protect (FLAG_PROTECT_SET, + CFG_MONITOR_BASE, 0xffffffff, + &flash_info[CFG_MAX_FLASH_BANKS - 1]); + + /* Environment protection ON by default */ + flash_protect (FLAG_PROTECT_SET, + CFG_ENV_ADDR, + CFG_ENV_ADDR + CFG_ENV_SECT_SIZE - 1, + &flash_info[CFG_MAX_FLASH_BANKS - 1]); + + /* Redundant environment protection ON by default */ + flash_protect (FLAG_PROTECT_SET, + CFG_ENV_ADDR_REDUND, + CFG_ENV_ADDR_REDUND + CFG_ENV_SIZE_REDUND - 1, + &flash_info[CFG_MAX_FLASH_BANKS - 1]); + } + + return 0; +} + +/* + * Initialize Local Bus + */ +void local_bus_init (void) +{ + volatile immap_t *immap = (immap_t *) CFG_IMMR; + volatile ccsr_gur_t *gur = &immap->im_gur; + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + + uint clkdiv; + uint lbc_hz; + sys_info_t sysinfo; + + /* + * Errata LBC11. + * Fix Local Bus clock glitch when DLL is enabled. + * + * If localbus freq is < 66Mhz, DLL bypass mode must be used. + * If localbus freq is > 133Mhz, DLL can be safely enabled. + * Between 66 and 133, the DLL is enabled with an override workaround. + */ + + get_sys_info (&sysinfo); + clkdiv = lbc->lcrr & 0x0f; + lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; + + if (lbc_hz < 66) { + lbc->lcrr = CFG_LBC_LCRR | 0x80000000; /* DLL Bypass */ + lbc->ltedr = 0xa4c80000; /* DK: !!! */ + + } else if (lbc_hz >= 133) { + lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ + + } else { + /* + * On REV1 boards, need to change CLKDIV before enable DLL. + * Default CLKDIV is 8, change it to 4 temporarily. + */ + uint pvr = get_pvr (); + uint temp_lbcdll = 0; + + if (pvr == PVR_85xx_REV1) { + /* FIXME: Justify the high bit here. */ + lbc->lcrr = 0x10000004; + } + + lbc->lcrr = CFG_LBC_LCRR & (~0x80000000); /* DLL Enabled */ + udelay (200); + + /* + * Sample LBC DLL ctrl reg, upshift it to set the + * override bits. + */ + temp_lbcdll = gur->lbcdllcr; + gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000); + asm ("sync;isync;msync"); + } +} + +#if defined(CONFIG_PCI) +/* + * Initialize PCI Devices, report devices found. + */ + +#ifndef CONFIG_PCI_PNP +static struct pci_config_table pci_mpc85xxads_config_table[] = { + {PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + PCI_IDSEL_NUMBER, PCI_ANY_ID, + pci_cfgfunc_config_device, {PCI_ENET0_IOADDR, + PCI_ENET0_MEMADDR, + PCI_COMMAND_MEMORY | + PCI_COMMAND_MASTER}}, + {} +}; +#endif + + +static struct pci_controller hose = { +#ifndef CONFIG_PCI_PNP + config_table:pci_mpc85xxads_config_table, +#endif +}; + +#endif /* CONFIG_PCI */ + + +void pci_init_board (void) +{ +#ifdef CONFIG_PCI + extern void pci_mpc85xx_init (struct pci_controller *hose); + + pci_mpc85xx_init (&hose); +#endif /* CONFIG_PCI */ +} diff --git a/board/tqm85xx/u-boot.lds b/board/tqm85xx/u-boot.lds new file mode 100644 index 0000000000..65d0c04ced --- /dev/null +++ b/board/tqm85xx/u-boot.lds @@ -0,0 +1,149 @@ +/* + * (C) Copyright 2002,2003, Motorola,Inc. + * Xianghua Xiao, X.Xiao@motorola.com. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/mpc85xx/start.o (.bootpg) + board/tqm85xx/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/tqm85xx/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + cpu/mpc85xx/speed.o (.text) + cpu/mpc85xx/pci.o (.text) + common/dlmalloc.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/include/configs/TQM8540.h b/include/configs/TQM8540.h deleted file mode 100644 index 2cd46c96fb..0000000000 --- a/include/configs/TQM8540.h +++ /dev/null @@ -1,464 +0,0 @@ -/* - * Copyright 2005 DENX Software Engineering - * Wolfgang Denk - * Copyright 2004 Freescale Semiconductor. - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * TQM8540 board configuration file - * - * Make sure you change the MAC address and other network params first, - * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_MPC8540 1 /* MPC8540 specific */ -#define CONFIG_TQM8540 1 /* TQM8540 board specific */ - -#define CONFIG_PCI -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ - -/* - * sysclk for MPC85xx - * - * Two valid values are: - * 33000000 - * 66000000 - * - * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz - * is likely the desired value here, so that is now the default. - * The board, however, can run at 66MHz. In any event, this value - * must match the settings of some switches. Details can be found - * in the README.mpc85xxads. - */ - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 33333333 -#endif - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00000000 /* memtest region */ -#define CFG_MEMTEST_END 0x10000000 - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ - -/* - * DDR Setup - */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE - -#if defined(CONFIG_SPD_EEPROM) - /* - * Determine DDR configuration from I2C interface. - */ - #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ - -#else - /* - * Manually set up DDR parameters - */ - #define CFG_SDRAM_SIZE 512 /* DDR is 256MB */ - #define CFG_DDR_CS0_BNDS 0x0000001f /* 0-256MB */ - #define CFG_DDR_CS0_CONFIG 0x80000102 - #define CFG_DDR_TIMING_1 0x47445331 - #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ - #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ - #define CFG_DDR_MODE 0x40020062 /* DLL,normal,seq,4/2.5 */ - #define CFG_DDR_INTERVAL 0x05160100 /* autocharge,no open page */ -#endif - -/* - * Flash on the Local Bus - */ -#define CFG_LBC_FLASH_BASE 0xfe000000 /* Localbus SDRAM */ -#define CFG_LBC_FLASH_SIZE 32 /* LBC SDRAM is 32MB */ - -#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH 32M */ -#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */ - -#define CFG_OR0_PRELIM 0xfe000040 /* 32MB Flash */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ - -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT -#else -#undef CFG_RAMBOOT -#endif - -#define CFG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO - -#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ - -/* - * LSDMR masks - */ -#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) -#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) -#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) -#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16)) -#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) -#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) -#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) -#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) -#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) -#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) -#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) -#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27)) -#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) -#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29)) -#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) - -#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) - -#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \ - | CFG_LBC_LSDMR_RFCR5 \ - | CFG_LBC_LSDMR_PRETOACT3 \ - | CFG_LBC_LSDMR_ACTTORW3 \ - | CFG_LBC_LSDMR_BL8 \ - | CFG_LBC_LSDMR_WRC2 \ - | CFG_LBC_LSDMR_CL3 \ - | CFG_LBC_LSDMR_RFEN \ - ) - -/* - * SDRAM Controller configuration sequence. - */ -#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_PCHALL) -#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_ARFRSH) -#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_ARFRSH) -#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_MRW) -#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_NORMAL) - -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ - -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_CONS_INDEX 1 -#undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) - -/* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#endif - -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */ - -/* I2C RTC */ -#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* I2C EEPROM */ -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also). - */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ - -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 - -/* RapidIO MMU */ -#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ -#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xe2000000 -#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ - -#if defined(CONFIG_PCI) - -#define CONFIG_NET_MULTI -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - - -#if defined(CONFIG_TSEC_ENET) - -#ifndef CONFIG_NET_MULTI -#define CONFIG_NET_MULTI 1 -#endif - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MPC85XX_TSEC1 1 -#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" -#define CONFIG_MPC85XX_TSEC2 1 -#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 - -#define CONFIG_MPC85XX_FEC 1 -#define CONFIG_MPC85XX_FEC_NAME "FEC" -#define FEC_PHY_ADDR 3 -#define FEC_PHYIDX 0 - -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 - -/* Options are TSEC[0-1], FEC */ -#define CONFIG_ETHPRIME "TSEC1" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#ifndef CFG_RAMBOOT - #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000) - #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CFG_ENV_SIZE 0x2000 - #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET-CFG_ENV_SECT_SIZE) - #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ - #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) - #define CFG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - -#if defined(CFG_RAMBOOT) -# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL & ~(CFG_CMD_ENV | CFG_CMD_LOADS)) -#else -# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL | \ - CFG_CMD_DHCP | \ - CFG_CMD_NFS | \ - CFG_CMD_SNTP ) -#endif - -#if defined(CONFIG_PCI) -# define ADD_PCI_CMD (CFG_CMD_PCI) -#else -# define ADD_PCI_CMD 0 -#endif - -#define CONFIG_COMMANDS (CONFIG_CMD_PRIV | \ - ADD_PCI_CMD | \ - CFG_CMD_I2C | \ - CFG_CMD_DATE | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DTT | \ - CFG_CMD_MII | \ - CFG_CMD_PING ) -#include - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ - -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - - -#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ - -#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consdev=ttyS0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $bootargs " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ - ":$hostname:$netdev:off panic=1\0" \ - "addcons=setenv bootargs $bootargs " \ - "console=$consdev,$baudrate\0" \ - "flash_nfs=run nfsargs addip addcons;" \ - "bootm $kernel_addr\0" \ - "flash_self=run ramargs addip addcons;" \ - "bootm $kernel_addr $ramdisk_addr\0" \ - "net_nfs=tftp $loadaddr $bootfile;" \ - "run nfsargs addip addcons;bootm\0" \ - "rootpath=/opt/eldk/ppc_85xx\0" \ - "bootfile=/tftpboot/tqm8540/uImage\0" \ - "kernel_addr=FE000000\0" \ - "ramdisk_addr=FE100000\0" \ - "load=tftp 100000 /tftpboot/tqm8540/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#endif /* __CONFIG_H */ diff --git a/include/configs/TQM8560.h b/include/configs/TQM8560.h deleted file mode 100644 index e7b11e6d36..0000000000 --- a/include/configs/TQM8560.h +++ /dev/null @@ -1,473 +0,0 @@ -/* - * Copyright 2005 DENX Software Engineering - * Wolfgang Denk - * Copyright 2004 Freescale Semiconductor. - * (C) Copyright 2002,2003 Motorola,Inc. - * Xianghua Xiao - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * TQM8560 board configuration file - * - * Make sure you change the MAC address and other network params first, - * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_CPM2 1 /* has CPM2 */ -#define CONFIG_MPC8560 1 /* MPC8560 specific */ -#define CONFIG_TQM8560 1 /* TQM8560 board specific */ - -/* - * BIG FAT WARNING: Right now PCI seems to have a problem on the - * TQM8560 on the Starter Kit. So, if the board doen't come up - * please disable the PCI support for now. sr@denx.de, 15-09-2005 - */ -#define CONFIG_PCI -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ - -/* - * sysclk for MPC85xx - * - * Two valid values are: - * 33000000 - * 66000000 - * - * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz - * is likely the desired value here, so that is now the default. - * The board, however, can run at 66MHz. In any event, this value - * must match the settings of some switches. Details can be found - * in the README.mpc85xxads. - */ - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 33333333 -#endif - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00000000 /* memtest region */ -#define CFG_MEMTEST_END 0x10000000 - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ - -/* - * DDR Setup - */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE - -#if defined(CONFIG_SPD_EEPROM) - /* - * Determine DDR configuration from I2C interface. - */ - #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ - -#else - /* - * Manually set up DDR parameters - */ - #define CFG_SDRAM_SIZE 512 /* DDR is 256MB */ - #define CFG_DDR_CS0_BNDS 0x0000001f /* 0-256MB */ - #define CFG_DDR_CS0_CONFIG 0x80000102 - #define CFG_DDR_TIMING_1 0x47445331 - #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */ - #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */ - #define CFG_DDR_MODE 0x40020062 /* DLL,normal,seq,4/2.5 */ - #define CFG_DDR_INTERVAL 0x05160100 /* autocharge,no open page */ -#endif - -/* - * Flash on the Local Bus - */ -#define CFG_LBC_FLASH_BASE 0xfe000000 /* Localbus SDRAM */ -#define CFG_LBC_FLASH_SIZE 32 /* LBC SDRAM is 32MB */ - -#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH 32M */ -#define CFG_BR0_PRELIM 0xfe001801 /* port size 32bit */ - -#define CFG_OR0_PRELIM 0xfe000040 /* 32MB Flash */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ - -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT -#else -#undef CFG_RAMBOOT -#endif - -#define CFG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO - -#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/ - -/* - * LSDMR masks - */ -#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) -#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) -#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) -#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16)) -#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) -#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19)) -#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) -#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22)) -#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) -#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) -#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) -#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27)) -#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) -#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29)) -#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) - -#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) -#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) - -#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \ - | CFG_LBC_LSDMR_RFCR5 \ - | CFG_LBC_LSDMR_PRETOACT3 \ - | CFG_LBC_LSDMR_ACTTORW3 \ - | CFG_LBC_LSDMR_BL8 \ - | CFG_LBC_LSDMR_WRC2 \ - | CFG_LBC_LSDMR_CL3 \ - | CFG_LBC_LSDMR_RFEN \ - ) - -/* - * SDRAM Controller configuration sequence. - */ -#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_PCHALL) -#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_ARFRSH) -#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_ARFRSH) -#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_MRW) -#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \ - | CFG_LBC_LSDMR_OP_NORMAL) - -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ - -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ - -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -/* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#endif - -/* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */ - -/* I2C RTC */ -#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* I2C EEPROM */ -/* - * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also). - */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ - -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 - -/* RapidIO MMU */ -#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ -#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xe2000000 -#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ - -#if defined(CONFIG_PCI) - -#define CONFIG_NET_MULTI -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#define CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ -#endif - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - - -#if defined(CONFIG_TSEC_ENET) - -#ifndef CONFIG_NET_MULTI -#define CONFIG_NET_MULTI 1 -#endif - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MPC85XX_TSEC1 1 -#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" -#define CONFIG_MPC85XX_TSEC2 1 -#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 - -#define CONFIG_MPC85XX_FEC 1 -#define CONFIG_MPC85XX_FEC_NAME "FEC" -#define FEC_PHY_ADDR 3 -#define FEC_PHYIDX 0 - -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 - -/* Options are TSEC[0-1], FEC */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -#define CONFIG_ETHER_ON_FCC -#define CONFIG_ETHER_ON_FCC3 -#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) -#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) -#define CFG_CPMFCR_RAMTYPE 0 -#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -/* - * Environment - */ -#ifndef CFG_RAMBOOT - #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000) - #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ - #define CFG_ENV_SIZE 0x2000 - #define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET-CFG_ENV_SECT_SIZE) - #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) -#else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ - #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) - #define CFG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - -#if defined(CFG_RAMBOOT) -# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL & ~(CFG_CMD_ENV | CFG_CMD_LOADS)) -#else -# define CONFIG_CMD_PRIV (CONFIG_CMD_DFL | \ - CFG_CMD_DHCP | \ - CFG_CMD_NFS | \ - CFG_CMD_SNTP ) -#endif - -#if defined(CONFIG_PCI) -# define ADD_PCI_CMD (CFG_CMD_PCI) -#else -# define ADD_PCI_CMD 0 -#endif - -#define CONFIG_COMMANDS (CONFIG_CMD_PRIV | \ - ADD_PCI_CMD | \ - CFG_CMD_I2C | \ - CFG_CMD_DATE | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DTT | \ - CFG_CMD_MII | \ - CFG_CMD_PING ) -#include - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ - -/* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ -#endif - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - - -#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ - -#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consdev=ttyS0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $bootargs " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ - ":$hostname:$netdev:off panic=1\0" \ - "addcons=setenv bootargs $bootargs " \ - "console=$consdev,$baudrate\0" \ - "flash_nfs=run nfsargs addip addcons;" \ - "bootm $kernel_addr\0" \ - "flash_self=run ramargs addip addcons;" \ - "bootm $kernel_addr $ramdisk_addr\0" \ - "net_nfs=tftp $loadaddr $bootfile;" \ - "run nfsargs addip addcons;bootm\0" \ - "rootpath=/opt/eldk/ppc_85xx\0" \ - "bootfile=/tftpboot/tqm8560/uImage\0" \ - "kernel_addr=FE000000\0" \ - "ramdisk_addr=FE100000\0" \ - "load=tftp 100000 /tftpboot/tqm8560/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load;run update\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#endif /* __CONFIG_H */ diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h new file mode 100644 index 0000000000..18197f234d --- /dev/null +++ b/include/configs/TQM85xx.h @@ -0,0 +1,452 @@ +/* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Wolfgang Denk + * Copyright 2004 Freescale Semiconductor. + * (C) Copyright 2002,2003 Motorola,Inc. + * Xianghua Xiao + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * TQM85xx (8560/40/55/41) board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ + +#define CONFIG_PCI +#define CONFIG_TSEC_ENET /* tsec ethernet support */ + +#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + +/* + * Only MPC8540 doesn't have CPM module + */ +#ifndef CONFIG_MPC8540 +#define CONFIG_CPM2 1 /* has CPM2 */ +#endif + +/* + * sysclk for MPC85xx + * + * Two valid values are: + * 33000000 + * 66000000 + * + * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz + * is likely the desired value here, so that is now the default. + * The board, however, can run at 66MHz. In any event, this value + * must match the settings of some switches. Details can be found + * in the README.mpc85xxads. + */ + +#ifndef CONFIG_SYS_CLK_FREQ +#define CONFIG_SYS_CLK_FREQ 33333333 +#endif + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00000000 +#define CFG_MEMTEST_END 0x10000000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_ADD_RAM_INFO 1 /* print additional info*/ + +#if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) +/* TQM8540 & 8560 need DLL-override */ +#define CONFIG_DDR_DLL /* DLL fix needed */ +#define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */ +#endif /* defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) */ + +#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) +#define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ +#endif /* defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) */ + +/* + * Flash on the Local Bus + */ +#define CFG_FLASH0 0xFC000000 +#define CFG_FLASH1 0xF8000000 +#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 } + +#define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */ +#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ + +#define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */ +#define CFG_OR0_PRELIM 0xfc000040 /* 64MB Flash */ +#define CFG_BR1_PRELIM 0xf8001801 /* port size 32bit */ +#define CFG_OR1_PRELIM 0xfc000040 /* 64MB Flash */ + +#define CFG_FLASH_CFI /* flash is CFI compat. */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/ +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ + +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#if defined(CONFIG_TQM8560) + +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +#else + +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +#endif /* CONFIG_TQM8560 */ + +#define CONFIG_BAUDRATE 115200 + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */ + +/* I2C RTC */ +#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */ +#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* I2C EEPROM */ +/* + * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work also). + */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ + +/* I2C SYSMON (LM75) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CFG_DTT_MAX_TEMP 70 +#define CFG_DTT_LOW_TEMP -30 +#define CFG_DTT_HYSTERESIS 3 + +/* RapidIO MMU */ +#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE +#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#if defined(CONFIG_PCI) + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#define CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + + +#define CONFIG_NET_MULTI 1 + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" +#define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define FEC_PHY_ADDR 3 +#define FEC_PHYIDX 0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 + +/* Options are TSEC[0-1], FEC */ +#define CONFIG_ETHPRIME "TSEC0" + +#if defined(CONFIG_TQM8540) +/* + * TQM8540 has 3 ethernet ports. 2 TSEC's and one FEC. + * The FEC port is connected on the same signals as the FCC3 port + * of the TQM8560 to the baseboard (STK85xx Starterkit). + * + * On the STK85xx Starterkit the X47/X50 jumper has to be set to + * a - d (X50.2 - 3) to enable the FEC port. + */ +#define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" +#endif + +#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) +/* + * TQM8541/55 have 4 ethernet ports. 2 TSEC's and 2 FCC's. Only one FCC port + * can be used at once, since only one FCC port is available on the STK85xx + * Starterkit. + * + * To use this port you have to configure U-Boot to use the FCC port 1...2 + * and set the X47/X50 jumper to: + * FCC1: a - b (X47.2 - X50.2) + * FCC2: a - c (X50.2 - 1) + */ +#define CONFIG_ETHER_ON_FCC +#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ +#endif + +#if defined(CONFIG_TQM8560) +/* + * TQM8560 has 5 ethernet ports. 2 TSEC's and 3 FCC's. Only one FCC port + * can be used at once, since only one FCC port is available on the STK85xx + * Starterkit. + * + * To use this port you have to configure U-Boot to use the FCC port 1...3 + * and set the X47/X50 jumper to: + * FCC1: a - b (X47.2 - X50.2) + * FCC2: a - c (X50.2 - 1) + * FCC3: a - d (X50.2 - 3) + */ +#define CONFIG_ETHER_ON_FCC +#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ +#endif + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) +#define CONFIG_ETHER_ON_FCC1 +#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) +#define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) +#define CFG_CPMFCR_RAMTYPE 0 +#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) +#define CONFIG_ETHER_ON_FCC2 +#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +#define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) +#define CFG_CPMFCR_RAMTYPE 0 +#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif + +#if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) +#define CONFIG_ETHER_ON_FCC3 +#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) +#define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) +#define CFG_CPMFCR_RAMTYPE 0 +#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000) +#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CFG_ENV_SIZE 0x2000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_TIMESTAMP /* Print image info with ts */ + +#if defined(CONFIG_PCI) +# define ADD_PCI_CMD (CFG_CMD_PCI) +#else +# define ADD_PCI_CMD 0 +#endif + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_NFS | \ + CFG_CMD_SNTP | \ + ADD_PCI_CMD | \ + CFG_CMD_I2C | \ + CFG_CMD_DATE | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DTT | \ + CFG_CMD_MII | \ + CFG_CMD_PING ) +#include + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) + #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + + +#define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ + +#define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + CFG_BOOTFILE \ + "netdev=eth0\0" \ + "consdev=ttyS0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask" \ + ":$hostname:$netdev:off panic=1\0" \ + "addcons=setenv bootargs $bootargs " \ + "console=$consdev,$baudrate\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm $kernel_addr\0" \ + "flash_self=run ramargs addip addcons;" \ + "bootm $kernel_addr $ramdisk_addr\0" \ + "net_nfs=tftp $loadaddr $bootfile;" \ + "run nfsargs addip addcons;bootm\0" \ + "rootpath=/opt/eldk/ppc_85xx\0" \ + "kernel_addr=FE000000\0" \ + "ramdisk_addr=FE100000\0" \ + "load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \ + "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ + "cp.b 100000 fffc0000 40000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#endif /* __CONFIG_H */ diff --git a/lib_ppc/board.c b/lib_ppc/board.c index b8dd18ba92..f2a4746064 100644 --- a/lib_ppc/board.c +++ b/lib_ppc/board.c @@ -197,6 +197,10 @@ static int init_baudrate (void) /***********************************************************************/ +#ifdef CONFIG_ADD_RAM_INFO +void board_add_ram_info(int); +#endif + static int init_func_ram (void) { #ifdef CONFIG_BOARD_TYPES @@ -207,7 +211,11 @@ static int init_func_ram (void) puts ("DRAM: "); if ((gd->ram_size = initdram (board_type)) > 0) { - print_size (gd->ram_size, "\n"); + print_size (gd->ram_size, ""); +#ifdef CONFIG_ADD_RAM_INFO + board_add_ram_info(0); +#endif + putc('\n'); return (0); } puts (failed); diff --git a/net/eth.c b/net/eth.c index b4ff5eff63..66884eff02 100644 --- a/net/eth.c +++ b/net/eth.c @@ -157,9 +157,6 @@ int eth_initialize(bd_t *bis) #ifdef SCC_ENET scc_initialize(bis); #endif -#if defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FCC) - fec_initialize(bis); -#endif #if defined(CONFIG_MPC5xxx_FEC) mpc5xxx_fec_initialize(bis); #endif @@ -193,6 +190,9 @@ int eth_initialize(bd_t *bis) tsec_initialize(bis, 3, CONFIG_MPC83XX_TSEC4_NAME); # endif #endif +#if defined(FEC_ENET) || defined(CONFIG_ETHER_ON_FCC) + fec_initialize(bis); +#endif #if defined(CONFIG_AU1X00) au1x00_enet_initialize(bis); #endif -- cgit v1.2.1