summaryrefslogtreecommitdiffstats
path: root/include/configs
Commit message (Collapse)AuthorAgeFilesLines
* spi: tegra2: rename tegra2_spi.* to tegra_spi.*Tom Warren2012-07-071-1/+1
| | | | | | | | In anticipation of Tegra3 support, start removing/renaming Tegra2-specific files. No functional changes (yet). Also updated copyright to 2012. Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: whistler: store environment in eMMCStephen Warren2012-07-071-2/+9
| | | | | | | | | | | | | | | Store the environment in eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage: U-Boot is stored well below this location, and the kernel only uses the general area of the eMMC once booted, not the boot sectors. Note: This assumes the user plugged the standard 8MB MoviNAND card into J29/HSMMC/POP. If they didn't, the boot sector layout may be different. However, use of that particular card is standard practice as far as I know. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: ventana: store environment in eMMCStephen Warren2012-07-071-2/+4
| | | | | | | | | | Store the environment in eMMC, at the end of the second boot sector. This should not conflict with any other eMMC usage: U-Boot is stored well below this location, and the kernel only uses the general area of the eMMC once booted, not the boot sectors. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: ventana: add own device tree, enable USBStephen Warren2012-07-071-1/+15
| | | | | | | | | | Add a device tree for Ventana; the Seaboard file no longer represents the HW present on Ventana. Enable USB on Ventana. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: remove CONFIG_USB_ETHER_SMSC95XX from boards without itStephen Warren2012-07-074-4/+0
| | | | | | | | | | | | | | The SMSC95xx series may exist either directly on a main board, or as a USB to Ethernet dongle. However, dongles containing these chips are very rare. Hence, remove this config option, except on Harmony where such a chip is actually present on the board. The asix option remains, since it's a popular chip, and I actively use a dongle containing this. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* tegra: paz00: add device tree supportStephen Warren2012-07-071-1/+21
| | | | | | | ... to enable USB host support, which enables Ethernet support. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: harmony: add device tree supportStephen Warren2012-07-071-1/+21
| | | | | | | ... to enable USB host support, which enables Ethernet support. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Compulab TrimSlice board supportStephen Warren2012-07-071-0/+89
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: seaboard: add support for USB networkingStephen Warren2012-07-071-0/+9
| | | | | Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: whistler: reduce and comment network cfg optionsStephen Warren2012-07-071-6/+4
| | | | | | | | | CONFIG_CMD_PING/NFS aren't required for Whistler to boot. Add some comments. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: flesh out bootcmdStephen Warren2012-07-079-3/+135
| | | | | | | | | | | | | | | | | | | | | | | | | This implements a useful bootcmd for Tegra. The boot order is: * If USB enabled, USB storage * Internal MMC (SD card or eMMC) * If networking is enabled, BOOTP/TFTP When booting from USB or MMC, the boot script is assumed to be in partition 1 (although this may be overridden via the rootpart variable), both ext2 and FAT filesystems are supported, the boot script may exist in either / or /boot, and the boot script may be named boot.scr.uimg or boot.scr. When booting over the network, it is assumed that boot.scr.uimg exists on the TFTP server. There is less flexibility here since those setting up network booting are expected to need less hand-holding. In all cases, it is expected that the initial file loaded is a U-Boot image containing a script that will load the kernel, load any required initrd, load any required DTB, and finally bootm the kernel. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: remove some cruft from CONFIG_EXTRA_ENV_SETTINGSStephen Warren2012-07-078-10/+0
| | | | | | | | | | | | | | | | console isn't used by anything, and the kernel should be set appropriately by whatever script is booting the kernel, not imposed by the bootloader. mem might be useful, but the current value is pretty bogus, since it includes nvmem options that make no sense for an upstream kernel, and equally should not be required for any downstream kernel. Either way, this is also best left to the kernel boot script. smpflag isn't used by anything, and again was probably intended to be a kernel command-line option better set by the kernel boot script. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Whistler board supportStephen Warren2012-07-071-0/+90
| | | | | | | | | | | | | | | | | | | Whistler is a highly configurable Tegra evaluation and development board. This change adds support for the following specific configuration: E1120 motherboard E1108 CPU board E1116 PMU board The motherboard configuration switches are set as follows: SW1=0 SW2=0 SW3=5 S1/S2/S3/S4 all on, except S3 7/8 are off. Other combinations of daugher boards may work to varying degrees, but will likely require some SW adjustment. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* spi: Tegra2: Seaboard: enable SPI/UART corruption fixTom Warren2012-07-071-0/+9
| | | | Signed-off-by: Tom Warren <twarren@nvidia.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-20263-449/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* CONFIG_SYS_BAUDRATE_TABLE: Add <config_fallbacks.h>, place thereTom Rini2012-06-20238-400/+0
| | | | | | | | | We provide a default table of { 9600, 19200, 38400, 57600, 115200 } in <config_fallbacks.h> which mkconfig places after <configs/...h> in the generated config file. This is used when a board has not set its own table. Signed-off-by: Tom Rini <trini@ti.com>
* km/common: check test_bank and testpin for testbootThomas Herzmann2012-06-151-1/+3
| | | | | | | | | | If the testpin is asserted, first check if a test_bank variable is defined before trying to boot this test_bank. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx: configure CONFIG_POST for kmcoge5neThomas Herzmann2012-06-151-0/+8
| | | | | | | | | | kmcoge5ne starts the post tests if the testpin on the board was enabled. Currently it does simply a memory test. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: increase bootlimit to 3Holger Brunck2012-06-151-1/+1
| | | | | | | | Increase bootlimit to 3 to be more tolerant during the boot process before switching to the backup application. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx: add kmcoge5ne board supportHolger Brunck2012-06-153-172/+283
| | | | | | | | | | | | | | | | | | This board is a MPC8360 board. Two flashes are present a NOR flash were u-boot and the u-boot environment is stored and a NAND flash for the application code. This board has 512MB SDRAM. Additionaly we introduce a common km8360.h file and convert kmeter1 to use this. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Christian Herzig <christian.herzig@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* km/common: add support for second flashAndreas Huber2012-06-154-19/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for a second flash. By default, a single flash chip is set up: - called 'boot' - mtd name for ubi 'ubi0' MTDIDS and MTDPARTS may be overwritten to add a second flash. The 'ubiattach' command is featured in two versions: - if CONFIG_KM_UBI_PARTITION_NAME_APP is not defined: this is the version as up to now - if CONFIG_KM_UBI_PARTITION_NAME_APP is defined: a check on 'actual_bank' will be done to determine the flash to boot from. Use CONFIG_KM_UBI_PARTITION_NAME_BOOT and CONFIG_KM_UBI_PARTITION_NAME_APP to define where to put the bootloader and the applications. Example: In the board config do: ... snip ... "boot:" \ "768k(u-boot)," \ "128k(env)," \ "128k(envred)," \ "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" \ "app:" \ "-(" CONFIG_KM_UBI_PARTITION_NAME_APP ");" ... snap ... You may also need to enable the second flash: ... snip ... /* additional featured for COGE5 */ ... snap ... Signed-off-by: Andreas Huber <andreas.huber@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc83xx/km: remove unneeded CONFIG_PCI for kmeter1Holger Brunck2012-06-151-15/+0
| | | | | | | | | | | | We don't use PCI on kmeter1 and never will be, so remove some unneeded code. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx/km: use tuxx1.h for kmsupx5 targetHolger Brunck2012-06-152-100/+13
| | | | | | | | | | | | This additional header is unneeded, we can use the tuxx1.h for this target. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Heiko Schocher <hs@denx.de> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/83xx: increment malloc heap size for the MPC832x MDS boardsTimur Tabi2012-06-151-1/+1
| | | | | | | | | | | | | | | | | | | The malloc buffer is not large enough to hold a flash sector (0x20000 bytes) in addition to whatever else it normally holds, so double its size. This fixes a failure trying to save the environment: => save Saving Environment to Flash... Unable to save the rest of sector (122880) . done Protected 1 sectors This problem probably surfaced from some other change that significantly increased the normal memory usage, thereby not leaving enough room for the saveenv command. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-videoWolfgang Denk2012-06-073-3/+29
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-video: video: atmel/lcd: add LCD driver for new Atmel SoC video: cfb_console: flush dcache for frame buffer in DRAM cfb_console: Ignore bell character cfb_console: Add console_clear_line function cfb_console: Fix function console_back omap3_dss: cosmetic changes omap3_dss: add optional framebuffer mx53loco: Add LCD support mx5: Rename mx51_fb_init() mx53: Allow IPUv3 driver to also work on mx53 mx51evk: Add LCD support EXYNOS: display 32bpp bitmap TIZEN logo create lib/tizen directory LCD: display 32bpp decompressed bitmap image common/lcd.c: reduce one CONFIG_LCD_LOGO ifdef common/lcd.c: reduce some CONFIG_LCD_*_LOGO ifdefs common/lcd.c: use ARRAY_SIZE cmd_bmp.c: make bmp_display() usable by drivers or board code LCD: support another s6e8ax0 panel type LCD: change s6e8ax0 panel gamma value include/video.h: drop unused video_printf() Signed-off-by: Wolfgang Denk <wd@denx.de>
| * mx53loco: Add LCD supportFabio Estevam2012-05-251-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | Add support for CLAA07LC0ACW LCD that connects to the mx53loco board. Configure the board to show the Linux logo on the LCD. Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account the framebuffer usage. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
| * mx51evk: Add LCD supportFabio Estevam2012-05-251-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | Add support for CLAA07LC0ACW LCD that connects to the mx51evk board. Configure the board to show the Linux logo on the LCD. Also increase the size of CONFIG_SYS_MALLOC_LEN variable to take into account the framebuffer usage. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * EXYNOS: display 32bpp bitmap TIZEN logoDonghwa Lee2012-05-251-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch supports drawing 32bpp bitmap TIZEN logo in exynos fb. "tizen_hd_logo.h" data is compressed from trats_logo.bmp to trats_logo.bmp.gz by gzip and converted to tizen_hd_logo.h header file format by some application. The logo data is decompressed in the exynos fb driver by bmp_display(). Signed-off-by: Donghwa Lee <dh09.lee@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* | sh: Add SH7269 device and RSK2+SH7269 boardPhil Edworthy2012-05-281-0/+76
| | | | | | | | | | | | | | | | | | | | | | | | This is an sh2a device (max 266MHz) with FPU, video display controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports, SD and on-chip USB. The RSK2+SH7269 board uses the SH7269 processor. It is often referred to as just rsk7269. Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | sh: Set CONFIG_SH_ETHER_PHY_MODE and CONFIG_SH_ETHER_SH7734_MII to boards ↵Nobuhiro Iwamatsu2012-05-285-0/+6
| | | | | | | | | | | | | | | | | | with sh_eth The board with sh_eth needs to set CONFIG_SH_ETHER_PHY_MODE. And SH7734 needs to set value of CONFIG_SH_ETHER_SH7734_MII. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | sh: Add support for AP-SH4A-4A boardNobuhiro Iwamatsu2012-05-281-0/+176
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AP-SH4A-4A board has SH7734, 64MB DDR2-SDRAM, USB, Ethernet, and more. This patch supports the following functions: - 64MB DDR2-SDRAM - 16MB NOR Flash memory - Serial console (SCIF) - Ethernet (SH-Ether with Gigabit) - I2C Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | sh: r0p7734: Add support I2C controllerNobuhiro Iwamatsu2012-05-281-0/+17
| | | | | | | | | | | | | | This read MAC address from Serial EEPROM and set. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | sh: Add support for r0p7734 boardNobuhiro Iwamatsu2012-05-281-0/+167
|/ | | | | | | | | | | | | | The r0p7734 board has SH7734, 128MB DDR2-SDRAM, USB, Ethernet, and more. This patch supports the following functions: - 128MB DDR2-SDRAM - 32MB NOR Flash memory - Serial console (SCIF) - Ethernet (SH-Ether/SMSC) Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* net: Remove CMD_PING where there's no CMD_NETJoe Hershberger2012-05-233-3/+3
| | | | | | | | | Some boards claim to need ping, but don't support net. That makes no sense, and causes problems now that ping is in a separate file. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2012-05-2050-356/+842
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-arm: (167 commits) OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT ARM: omap3: Set SPL stack size to 8KB, image to 54KB. arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree omap4: do not enable auxiliary cores omap4: do not enable fs-usb module omap4: panda: disable uart2 pads during boot igep00x0: change mpurate from 500 to auto igep00x0: enable the use of a plain text file tegra2: trivially enable 13 mhz crystal frequency tegra: Enable keyboard for Seaboard tegra: Switch on console mux and use environment for console tegra: Add tegra keyboard driver tegra: fdt: Add keyboard definitions for Seaboard tegra: fdt: Add keyboard controller definition tegra: Add keyboard support to funcmux input: Add support for keyboard matrix decoding from an fdt input: Add generic keyboard input handler input: Add linux/input.h for key code support fdt: Add fdtdec functions to read byte array tegra: Enable LP0 on Seaboard tegra: fdt: Add EMC data for Tegra2 Seaboard tegra: i2c: Add function to find DVC bus fdt: tegra: Add EMC node to device tree tegra: Add EMC settings for Seaboard tegra: Turn off power detect in board init tegra: Set up warmboot code on Nvidia boards tegra: Setup PMC scratch info from ap20 setup tegra: Add warmboot implementation tegra: Set up PMU for Nvidia boards tegra: Add PMU to manage power supplies tegra: Add EMC support for optimal memory timings tegra: Add header file for APB_MISC register tegra: Add tegra_get_chip_type() to detect SKU tegra: Add flow, gp_padctl, fuse, sdram headers tegra: Add crypto library for warmboot code tegra: Add functions to access low-level Osc/PLL details tegra: Move ap20.h header into arch location Add AES crypto library i2c: Add TPS6586X driver Add abs() macro to return absolute value fdt: Add function to return next compatible subnode fdt: Add function to locate an array in the device tree i.MX28: Avoid redefining serial_put[cs]() i.MX28: Check if WP detection is implemented at all i.MX28: Add battery boot components to SPL i.MX28: Reorder battery status functions in SPL i.MX28: Add LRADC init to i.MX28 SPL i.MX28: Add LRADC register definitions i.MX28: Shut down the LCD controller before reset i.MX28: Add LCDIF register definitions i.MX28: Implement boot pads sampling and reporting i.MX28: Improve passing of data from SPL to U-Boot M28EVK: Add SD update command M28EVK: Implement support for new board V2.0 FEC: Abstract out register setup MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged i.MX28: Add delay after CPU bypass is cleared spi: mxs: Allow other chip selects to work spi: mxs: Introduce spi_cs_is_valid() mx53loco: Remove unneeded gpio_set_value() mx53loco: Add CONFIG_REVISION_TAG mx53loco: Turn on VUSB regulator mx53loco: Add mc34708 support and set mx53 frequency at 1GHz pmic: dialog: Avoid name conflicts imx: Add u-boot.imx as target for ARM9 i.MX SOCs i.MX2: Include asm/types.h in arch-mx25/imx-regs.h imx: usb: There is no such register i.MX25: usb: Set PORTSCx register imx: nand: Support flash based BBT i.MX25: This architecture has a GPIO4 too i.MX25: esdhc: Add mxc_get_clock infrastructure i.MX6: mx6q_sabrelite: add SATA bindings i.MX6: add enable_sata_clock() i.MX6: Add ANATOP regulator init mx28evk: add NAND support USB: ehci-mx6: Fix broken IO access M28: Scan only first 512 MB of DRAM to avoid memory wraparound Revert "i.MX28: Enable additional DRAM address bits" M28: Enable FDT support mx53loco: Add support for 1GHz operation for DA9053-based boards mx53loco: Allow to print CPU information at a later stage mx5: Add clock config interface imx-common: Factor out get_ahb_clk() i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow mx31pdk: Allow booting a zImage kernel mx6qarm2: Allow booting a zImage kernel mx6qsabrelite: Allow booting a zImage kernel mx28evk: Allow booting a zImage kernel m28evk: Allow to booting a dt kernel mx28evk: Allow to booting a dt kernel mx6qsabrelite: No need to set the direction for GPIO3_23 again pmic: Add support for the Dialog DA9053 PMIC MX53: mx53loco: Add SATA support MX53: Add support to ESG ima3 board SATA: add driver for MX5 / MX6 SOCs MX53: add function to set SATA clock to internal SATA: check for return value from sata functions MX5: Add definitions for SATA controller NET: fec_mxc.c: Add a way to disable auto negotiation Define UART4 and UART5 base addresses EXYNOS: Change bits per pixel value proper for u-boot. EXYNOS: support TRATS board display function LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI EXYNOS: support EXYNOS MIPI DSI interface driver. EXYNOS: support EXYNOS framebuffer and FIMD display drivers. LCD: add data structure for EXYNOS display driver EXYNOS: add LCD and MIPI DSI clock interface. EXYNOS: definitions of system resgister and power management registers. SMDK5250: fix compiler warning misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998 misc:pmic:max8997 MAX8997 support for PMIC driver TRATS: modify the trats's configuration ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT cm-t35: add I2C multi-bus support include/configs: Remove CONFIG_SYS_64BIT_STRTOUL include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF omap3: Introduce weak misc_init_r omap730p2: Remove empty misc_init_r omap5912osk: Remove empty misc_init_r omap4+: Remove CONFIG_ARCH_CPU_INIT omap4: Remove CONFIG_SYS_MMC_SET_DEV OMAP3: pandora: drop console kernel argument OMAP3: pandora: revise GPIO configuration ...
| * ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORTTom Rini2012-05-154-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As originally reported against beagleboard we currently have the following error message reported in SPL: U-Boot SPL 2012.04-00020-gb8310b9-dirty (Apr 25 2012 - 18:49:57) Texas Instruments Revision detection unimplemented OMAP SD/MMC: 0 timed out in wait_for_bb: I2C_STAT=1000 reading u-boot.img .... The reason for above message is that when booting from MMC, I2C needs to be initialized to talk with the TWL4030. On OMAP3 I2C is only initalized in SPL if CONFIG_SPL_BOARD_INIT is set. Cc: Thomas Weber <weber@corscience.de> Cc: Steve Sakoman <sakoman@gmail.com> Original patch for Beagleboard is: Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com> Extended to cover all other boards: Signed-off-by: Tom Rini <trini@ti.com>
| * ARM: omap3: Set SPL stack size to 8KB, image to 54KB.Tom Rini2012-05-159-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With older toolchains it is possible to not fit entirely into the 45KB that we had assigned to SPL. Adjust to allow for 8KB of stack (which should be more than required) and 54KB of text/data. Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Thomas Weber <weber@corscience.de> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
| * OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device TreeJon Hunter2012-05-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For OMAP4 boards, such as the panda-es, that have 1GB of memory the linux kernel fails to locate the device tree blob on boot. The reason being is that u-boot is copying the DT blob to the upper part of RAM when booting the kernel and the kernel is unable to access the blob. By setting the fdt_high variable to either 0xffffffff (to prevent the copy) or 0xac000000 (704MB boundary of memory for OMAP4) the kernel is able to locate the DT blob and boot. Based upon following patch by Dirk Behme set the fdt_high variable to allow booting with device tree on OMAP4 boards. "7e9603e i.mx6q: configs: Add fdt_high and initrd_high variables" Cc: Sricharan R <r.sricharan@ti.com> Cc: Sandeep Paulraj <s-paulraj@ti.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Jon Hunter <jon-hunter@ti.com>
| * igep00x0: change mpurate from 500 to autoEnric Balletbo i Serra2012-05-151-1/+1
| | | | | | | | | | | | | | | | This patch changes the default mpurate variable from 500 to auto on all IGEP boards, with this the default rate is autoselected. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
| * igep00x0: enable the use of a plain text fileEnric Balletbo i Serra2012-05-151-12/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on commit cf073e49bc3502be1b48a0e3faf0cde9edbb89db for beagleboard Using the new env import command it is possible to use plain text files instead of script-images. Plain text files are much easier to handle. E.g. If your boot.scr contains the following: ----------------------------------- setenv dvimode 1024x768-16@60 run loaduimage run mmcboot ----------------------------------- you could create a file named uEnv.txt and use that instead of boot.scr: ----------------------------------- dvimode=1024x768-16@60 uenvcmd=run loaduimage; run mmcboot ----------------------------------- The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence will be started, therefore you could just use ----------------------------------- dvimode=1024x768-16@60 ----------------------------------- as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
| * tegra: Enable keyboard for SeaboardSimon Glass2012-05-151-0/+8
| | | | | | | | | | | | | | This enables the standard keyboard on Seaboard. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: Switch on console mux and use environment for consoleSimon Glass2012-05-151-1/+8
| | | | | | | | | | | | | | All tegra boards will use these options by default. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * tegra: Enable LP0 on SeaboardSimon Glass2012-05-152-0/+25
| | | | | | | | | | | | | | This enables LP0 to support suspend / resume on Seaboard. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
| * i.MX28: Implement boot pads sampling and reportingMarek Vasut2012-05-152-0/+2
| | | | | | | | | | | | | | | | | | | | | | This patch implements code that samples i.MX28 boot pads and reports boot mode accordingly. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
| * M28EVK: Add SD update commandMarek Vasut2012-05-151-0/+9
| | | | | | | | | | | | | | | | | | | | | | Add "update_sd_firmware" command to easily reload the SD card of m28evk kit. This comes handy when the board boots from SD card. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
| * mx53loco: Add CONFIG_REVISION_TAGFabio Estevam2012-05-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information. The kernel uses this data to distinguish between Dialog versus mc34708 based boards, and also to distinguish between revA and revB of the mc34708 based boards. Suggested-by: Yu Li <yk@magniel.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * mx53loco: Add mc34708 support and set mx53 frequency at 1GHzFabio Estevam2012-05-151-0/+2
| | | | | | | | | | | | | | | | Add mc34708 support and set mx53 core frequency at its maximum value of 1GHz. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * i.MX6: mx6q_sabrelite: add SATA bindingsEric Nelson2012-05-151-0/+13
| | | | | | | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: stefano Babic <sbabic@denx.de>
| * mx28evk: add NAND supportLauri Hintsala2012-05-151-0/+10
| | | | | | | | | | | | | | | | NAND support is not enabled by default because Eval Kit is not delivered with NAND chip. To enable NAND support add CONFIG_CMD_NAND to board config. Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Acked-by: Marek Vasut <marex@denx.de>
| * M28: Scan only first 512 MB of DRAM to avoid memory wraparoundMarek Vasut2012-05-151-1/+1
| | | | | | | | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com>
OpenPOWER on IntegriCloud