summaryrefslogtreecommitdiffstats
path: root/include/configs/omap3_overo.h
Commit message (Collapse)AuthorAgeFilesLines
* kconfig: add config option for shell promptNikita Kiryanov2015-08-131-6/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add option to set shell prompt string from menuconfig and migrate boards globally. The migration is done as follows: - Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the entry moved to their defconfig files. - Boards that defined some kind of #ifdef logic which selects the CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT right before the #ifdef logic and were left alone. - This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h files. This results in a streamlined default value across platforms, and includes the following files: spear-common, sunxi-common, mv-common, ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common. - Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were not updated in their respective defconfig files under the assumption that since they did not explicitly define a value, they're fine with whatever the default is. - On the other hand, boards that relied on a value defined in some <boards>_common.h file such as woodburn_common, rpi-common, bur_am335x_common, ls2085a_common, siemens_am33x_common, and omap3_evm_common, had their values moved to the respective defconfig files. - The define V_PROMPT was removed, since it is not used anywhere except for assigning a value for CONFIG_SYS_PROMPT. Cc: Tom Rini <trini@konsulko.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> [trini: Add spring, sniper, smartweb to conversion] Signed-off-by: Tom Rini <trini@konsulko.com>
* ti: drop value from CONFIG_SYS_NAND_BUSWIDTH_16BITStefano Babic2015-08-121-1/+1
| | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
* Update the rootfs type to ext4 for Overo and PepperAdam YH Lee2015-07-271-1/+1
| | | | | | | Gumstix is migrating from ext3 to ext4 file system. Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com> Acked-by: Ash Charles <ashcharles@gmail.com>
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-251-3/+0
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* omap3: overo: Allow boot with kernel in UBI rootfsAsh Charles2015-05-101-0/+13
| | | | | | | | | | If regular NAND booting fails to find a valid uImage in the kernel partition in NAND, try to boot using a zImage and dtb found in a UBI volume in the rootfs partition. This is the NAND analog of mmc zImage booting for device-tree based kernels. Signed-off-by: Ash Charles <ashcharles@gmail.com> Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
* omap3: overo: Use software BCH8 ECC for NANDAsh Charles2015-05-101-4/+15
| | | | | | | | | | | | | | | | | | | | | Overo COMs have NAND flash that requires 4-bit ECC or better except for the first sector which can use 1-bit ECC. The boot ROM expects to load a payload from NAND written using 1-bit hardware-based ECC. In short, write SPL to NAND something like this (4 times for redundancy): #> nandecc hw #> nand write ${loadaddr} 0x0 ${filesize} #> nand write ${loadaddr} 0x20000 ${filesize} #> nand write ${loadaddr} 0x40000 ${filesize} #> nand write ${loadaddr} 0x60000 ${filesize} Then, switch back to software-based BCH8 for everything else: #> nandecc sw bch8 After [1], enlarge the max size of the SPL so the BCH code can fit. [1] https://www.mail-archive.com/u-boot@lists.denx.de/msg163912.html Signed-off-by: Ash Charles <ashcharles@gmail.com>
* omap3: overo: Add usb host supportStefan Herbrechtsmeier2014-10-231-0/+8
| | | | Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
* omap3: overo: Call bootm only after successful nand readStefan Herbrechtsmeier2014-10-231-2/+3
| | | | Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
* omap3: overo: Fix fdtfile testStefan Herbrechtsmeier2014-10-101-1/+1
| | | | | | | | | Commit 12cc54376768461533b55ada1b0b6d4979f40579 'omap3: overo: Select fdtfile for expansion board' wrongly missed the operator in the fdtfile test. Update the test to only overwrite an empty fdtfile environment variable. Signed-off-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
* ARM: omap: move board specific NAND configs out from ti_armv7_common.hpekon gupta2014-07-251-0/+6
| | | | | | | | | | | | | | | | | This patch moves some board specific NAND configs: - FROM: generic config file 'ti_armv7_common.h' - TO: individual board config files using these configs. So that each board can independently set the value as per its design. Following configs are affected in this patch: CONFIG_SYS_NAND_U_BOOT_OFFS: <refer doc/README.nand> CONFIG_CMD_SPL_NAND_OFS: <refer doc/README.falcon> CONFIG_SYS_NAND_SPL_KERNEL_OFFS: <refer doc/README.falcon> CONFIG_CMD_SPL_WRITE_SIZE: <refer doc/README.falcon> This patch also updates documentation for few of above NAND configs. Signed-off-by: Pekon Gupta <pekon@ti.com>
* ARM: omap: clean redundant PISMO_xx macros used in OMAP3pekon gupta2014-07-251-5/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PISMO_xx macros were used to define 'Platform Independent Storage MOdule' related GPMC configurations. This patch - Replaces these OMAP3 specific macros with generic CONFIG_xx macros as provided by current u-boot infrastructure. - Removes unused redundant macros, which are no longer required after merging of common platform code in following commit commit a0a37183bd75e74608bc78c8d0e2a34454f95a91 ARM: omap: merge GPMC initialization code for all platform +-----------------+-----------------------------------------------------------+ | Macro | Reason for removal | +-----------------+-----------------------------------------------------------+ | PISMO1_NOR_BASE | duplicate of CONFIG_SYS_FLASH_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_NAND_BASE| duplicate of CONFIG_SYS_NAND_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_ONEN_BASE| duplicate of CONFIG_SYS_ONENAND_BASE | +-----------------+-----------------------------------------------------------+ | PISMO1_NAND_SIZE| GPMC accesses NAND device via I/O mapped registers so | | | configuring GPMC chip-select for smallest allowable | | | segment (GPMC_SIZE_16M) is enough. | +-----------------+-----------------------------------------------------------+ | PISMO1_ONEN_SIZE| OneNAND uses a fixed GPMC chip-select address-space of | | | 128MB (GPMC_SIZE_128M) | +-----------------+-----------------------------------------------------------+ +-----------------+-----------------------------------------------------------+ | PISMO1_NOR | Unused Macros | | PISMO1_NAND | | | PISMO2_CS0 | | | PISMO2_CS1 | | | PISMO1_ONENAND | | | PISMO2_NAND_CS0 | | | PISMO2_NAND_CS1 | | | PISMO1_NOR_BASE | | | PISMO1_NAND_BASE| | | PISMO2_CS0_BASE | | +-----------------+-----------------------------------------------------------+ Signed-off-by: Pekon Gupta <pekon@ti.com>
* omap3: overo: Select fdtfile for expansion boardAsh Charles2014-06-191-5/+5
| | | | | | | | | | | | | | | | | The u-boot Overo board actually supports both Overo (OMAP35xx) and Overo Storm (AM/DM37xx) COMs with a range of different expansion boards. This provides a mechanism to select the an appropriate device tree file based on the processor version and, if available, the expansion board ID written on the expansion board EEPROM. To match the 3.15+ kernels, fdtfile names have this format: "omap3-overo[-storm]-<expansion board name>.dtb" By default, we use "omap3-overo-storm-tobi.dtb". Signed-off-by: Ash Charles <ashcharles@gmail.com> Conflicts: include/configs/omap3_overo.h
* mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device ↵pekon gupta2014-06-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | bus-width GPMC controller needs to be configured based on bus-width of the NAND device connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI parameters is not possible in following situations: SPL: SPL NAND drivers does not support ONFI parameter reading. U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init() which is called before probing for devices, hence any ONFI parameter information is not available during GPMC initialization. Thus, OMAP NAND driver expected board developers to explicitely write GPMC configurations specific to NAND device attached on board in board files itself. But this was troublesome for board manufacturers as they need to dive into lengthy platform & SoC documents to find details of GPMC registers and appropriate configurations to get NAND device working. This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config hich indicates that connected NAND device has x16 bus-width. And then based on this config GPMC driver itself initializes itself based on NAND bus-width. This keeps board developers free from knowing GPMC controller specific internals. Signed-off-by: Pekon Gupta <pekon@ti.com>
* omap3: overo: Use common configurations for OveroAsh Charles2014-05-231-194/+28
| | | | | | | | | | | | | Clean-up the board configuration file for the Gumstix Overo board by including common omap3 definitions from ti_omap3_common.h as suggested here [1]. [1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/185960 Signed-off-by: Ash Charles <ashcharles@gmail.com> Conflicts: include/configs/omap3_overo.h
* Allow overo to boot with device treeAsh Charles2014-05-231-20/+38
| | | | | | | Update the board configuration for Gumstix Overo. In particular, add support for zImage and DTB files on boot. Signed-off-by: Ash Charles <ashcharles@gmail.com>
* arm: omap3: Fix omap3_overo SPL boot hangupAsh Charles2014-05-231-0/+6
| | | | | | | | | | | Patch f33b9bd3 [arm: omap3: Enable clocks for peripherals only if they are used] breaks SPL booting on Overo. Since some gpio inputs are read to detect the board revision. But with this patch above, the clocks to the GPIO subsystems are not enabled per default any more. The GPIO banks need to be configured specifically now. Signed-off-by: Ash Charles <ashcharles@gmail.com>
* OMAP3: overo: eliminate hard-coded partition offsetsAsh Charles2014-05-231-9/+1
| | | | | | | | | | The linux kernel is at nand0,3 using the current layout, but is best accessed through the partition label "linux". Since CONFIG_CMD_MTDPARTS is defined the CONFIG_JFFS2 settings are unreferenced; use "setenv partition rootfs" to set the default mtd partition for jffs2. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
* OMAP3: overo: increase linux partition to 8 MiBPeter A. Bigot2014-05-231-2/+2
| | | | | | | | Linux kernel at version 3.5 is about 3.5 MiB; test kernels for 3.10 exceed 4 MiB. Prepare for future upgrades by increasing the NAND partition now. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
* OMAP3: overo: add command support for mtd and ubiAsh Charles2014-05-231-3/+37
| | | | | | | | | The NAND linux partition format default was changed from jffs2 to ubi in 254973e6df0e48f1a72b67905185c774dcd9f394 but the corresponding commands were not enabled. Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
* omap: overo: allow the use of a plain text env file instead boot scriptsAsh Charles2014-05-231-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adapted from d70f5480 described below. commit d70f54808dfa83b574e1239c3eccbcf3317343e1 Author: Javier Martinez Canillas <javier@dowhile0.org> Date: Mon Jan 7 03:51:20 2013 +0000 omap4: allow the use of a plain text env file instead boot scripts For production systems it is better to use script images since they are protected by checksums and carry valuable information like name and timestamp. Also, you can't validate the content passed to env import. But for development, it is easier to use the env import command and plain text files instead of script-images. Since both OMAP4 supported boards (Panda and TI SDP4430) are used primarily for development, this patch allows U-Boot to load env var from a text file in case that an boot.scr script-image is not present. The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence will be started. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
* mtd: nand: omap: remove unused #defines from common omap_gpmc.hpekon gupta2014-03-041-2/+0
| | | | | | | | | | | | | | | | | OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI params or nand_id[] table. And based on that it defines ECC layout. This patch 1) removes following board configs used for defining NAND ECC layout - GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND) - GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND) - GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND) - GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND) 2) removes unused #defines in common omap_gpmc.h depending on above configs Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: Pekon Gupta <pekon@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini2013-11-251-0/+1
|\
| * mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-schemepekon gupta2013-11-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed CONFIG_xx used for selecting NAND ecc-schemes. This patch aims at solving following issues. 1) Currently ecc-scheme is tied to SoC platform, which prevents user to select other ecc-schemes also supported in hardware. like; - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW). - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware supports BCH16 ecc-scheme also. 2) Different platforms use different CONFIG_xx to select ecc-schemes, which adds confusion for user while migrating platforms. - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only 8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW) whereas ELM hardware engine supports other ecc-schemes also like; BCH4, and BCH16 (in future). - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW). - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency on SoC platform and NAND driver. And user can select ecc-scheme independently foreach board. However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand) Signed-off-by: Pekon Gupta <pekon@ti.com>
* | i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher2013-11-131-5/+4
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
* config: remove platform CONFIG_SYS_HZ definition part 2/2Rob Herring2013-11-041-1/+0
| | | | | | Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* ARM: OMAP: Add CONFIG_OMAP_COMMONLokesh Vutla2013-08-151-0/+1
| | | | | | | Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-13/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* spl/nand: introduce CONFIG_SPL_NAND_DRIVERS, _BASE, and _ECC.Scott Wood2012-11-261-0/+3
| | | | | | | | | | | | | | Some small SPLs do not use nand_base.c, and a subset of those also require a special driver. Some SPLs need software ECC but others can't fit it. All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these symbols added to preserve existing behavior. Signed-off-by: Scott Wood <scottwood@freescale.com> -- v2: use positive logic for including bits of NAND, rather than a MINIMAL symbol that excludes things.
* configs: Fix usage of mmc rescanAndrew Bradford2012-10-231-1/+1
| | | | | | | | Fix usage of 'mmc rescan' by many configs. Proper use is 'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan the device. 'mmc rescan' itself does not take any arguments. Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
* SPL: Move the omap SPL framework to common/splTom Rini2012-09-271-0/+1
| | | | | | | | | | | | | Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL framework, enable on all of the previously using boards. We move the spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave the NAND one in-place as we plan to replace it later in this series. We use common/spl to avoid linker problems with respect to merging constant strings in objects. Otherwise all strings in common/ will be linked in and kept which grows SPL in size too much. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: Remove unused stack and irq config definesRob Herring2012-09-011-8/+0
| | | | | | | | | | | CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* dm: Move OMAP GPIO driver to drivers/gpio/Marek Vasut2012-09-011-0/+1
| | | | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* dm: Select CONFIG_SPL_GPIO_SUPPORT on OMAPMarek Vasut2012-09-011-0/+1
| | | | | | | | | | | | | This fixes the breakage with SPL on most OMAP boards after the GPIO driver was moved. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: U-Boot DM <u-boot-dm@lists.denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-201-1/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORTTom Rini2012-05-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | As originally reported against beagleboard we currently have the following error message reported in SPL: U-Boot SPL 2012.04-00020-gb8310b9-dirty (Apr 25 2012 - 18:49:57) Texas Instruments Revision detection unimplemented OMAP SD/MMC: 0 timed out in wait_for_bb: I2C_STAT=1000 reading u-boot.img .... The reason for above message is that when booting from MMC, I2C needs to be initialized to talk with the TWL4030. On OMAP3 I2C is only initalized in SPL if CONFIG_SPL_BOARD_INIT is set. Cc: Thomas Weber <weber@corscience.de> Cc: Steve Sakoman <sakoman@gmail.com> Original patch for Beagleboard is: Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com> Extended to cover all other boards: Signed-off-by: Tom Rini <trini@ti.com>
* ARM: omap3: Set SPL stack size to 8KB, image to 54KB.Tom Rini2012-05-151-1/+1
| | | | | | | | | | | | | | | | With older toolchains it is possible to not fit entirely into the 45KB that we had assigned to SPL. Adjust to allow for 8KB of stack (which should be more than required) and 54KB of text/data. Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Thomas Weber <weber@corscience.de> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
* OMAP3: Remove unused CONFIG_SYS_NAND_ECCSTEPS/TOTALThomas Weber2012-02-271-4/+0
| | | | Signed-off-by: Thomas Weber <weber@corscience.de>
* overo: add SPL supportAndreas Müller2012-01-161-0/+52
| | | | | | | | | | * implementation based on ti beagleboard/omap3evm * timing data and i2c workaround for revision 0 boards taken from x-loader * run-tested with overo revision 0 and 1 / boot from NAND and SDcard * run-tested with x-loader Signed-off-by: Andreas Müller <schnitzeltony@gmx.de> Signed-off-by: Tom Rini <trini@ti.com>
* include/configs/omap3_overo.h: several cleanupsAndreas Müller2012-01-161-35/+31
| | | | | | | | | * remove unused macros * remove unused macro values * align tabs * remove Free Software Foundation address Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
* OMAP3: Remove unused define CONFIG_OMAP3_*_DDRThomas Weber2012-01-161-3/+0
| | | | | | | | | | | This patch removes the unused definitions: CONFIG_OMAP3_MICRON_DDR CONFIG_OMAP3_NUMONYX_DDR CONFIG_OMAP3_INFINEON_DDR Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
* omap: overo: Use ubifs instead of jffs2 for nandSteve Sakoman2011-12-091-2/+2
| | | | | Signed-off-by: Steve Sakoman <steve@sakoman.com> Tested-by: Ash Charles <ash@gumstix.com>
* ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unusedThomas Weber2011-12-061-4/+0
| | | | | | | | | | | This patch removes the definition of stack sizes for irq and fiq if the CONFIG_USE_IRQ is undefined before. Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
* ARM: OMAP3: Remove unused define SDRC_R_C_BThomas Weber2011-12-061-3/+0
| | | | | | | | | | | This patch removes the unused definition of SDRC_R_C_B from the config files. Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it> Acked-by: Tom Rini <trini@ti.com>
* ARM: OMAP3: Remove unused define CONFIG_OMAP3430Thomas Weber2011-12-061-1/+0
| | | | | | | | | | This patch removes the CONFIG_OMAP3430, because it is unused. Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Thomas Weber <weber@corscience.de> Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
* omap: fix cache line size for omap3/omap4 boardsAneesh V2011-12-061-0/+2
| | | | | | Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Aneesh V <aneesh@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: overo : Add environment variable optargs to bootargsPhilip Balister2011-10-271-0/+3
| | | | | | | | | | This allows the user can easily add extra kernel arguments. Very helpful for reserving memory for the DSP without rewriting the entire kernel argument line. Signed-off-by: Philip Balister <philip@opensdr.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3: overo : Use ttyO2 instead of ttyS2.Philip Balister2011-10-271-1/+1
| | | | | | | | | Starting with kernel 2.6.37, the serial ports on the OMAP3 are called ttyOX, not ttySX. Signed-off-by: Philip Balister <philip@opensdr.com> Tested-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* board configs: drop NET_MULTI referencesMike Frysinger2011-10-051-1/+0
| | | | | | | Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* OMAP: Remove omapfb.debug=y from Beagle and Overo env settingsSteve Sakoman2011-09-041-2/+0
| | | | | | | The kernel DSS2 code is mature now, and keeping this setting hurts performance Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* OMAP3/4: Increase console I/O buffer sizeVaibhav Hiremath2011-09-041-1/+1
| | | | | | | | | Increase the console I/O buffer size (SYS_CBSIZE) to 512 (from 256) required especially for bootargs string, as multiple options (e.g Video settings) are passed to the kernel through bootargs. Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OpenPOWER on IntegriCloud