summaryrefslogtreecommitdiffstats
path: root/include/configs/ls1021atwr.h
Commit message (Collapse)AuthorAgeFilesLines
* configs: ls1021atwr: Enable ID EEPROM for SD bootYao Yuan2015-10-301-2/+0
| | | | | | | | I2C1 can work on ls102xa rev2.0 SD boot, so add ID EEPROM for SD boot. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Set fdt_high and initrd_high to the value of 0xffffffffAlison Wang2015-10-291-4/+4
| | | | | | | | | | | | | | | | As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel fails to access the device tree blob on boot. The reason is that u-boot relocates the device tree blob into high memory when booting the kernel and the kernel is unable to access the blob. To avoid this issue, fdt_high is set to the value of 0xffffffff. The device tree blob will not get relocated and is still in low memory to make it accessible to the kernel. For the same reason, initrd_high is set to the value of 0xffffffff too. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv7/ls1021a: move ns_access to common fileMingkai Hu2015-10-291-1/+1
| | | | | | | | | | Config Security Level Register is different between different SoCs, so put the CSL register definition into the arch specific directory. Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* common/board_f.c: change the macro name and remove it for PPC platformsGong Qianyu2015-10-291-1/+1
| | | | | | | | | | For most PPC platforms, they will call the first get_clocks() in init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is then defined to call the second get_clocks(), which should be redundant for PPC. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls1021a: Add QSPI or IFC support in SD bootAlison Wang2015-10-261-3/+16
| | | | | | | | | | | | | | As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in SD boot now. For the customer's demand, QSPI needs to be supported in SD boot too. This patch adds QSPI or IFC support in SD boot according to the corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is used to support QSPI in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* QE: modify the address of qe ucodeZhao Qiang2015-10-261-1/+1
| | | | | | | The address of uboot changed, so change qe ucode Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm/fsl-ls: Add CONFIG_OF_STDOUT_VIA_ALIASScott Wood2015-10-261-0/+1
| | | | | | | | This will allow OF-based earlycon to be used once the appropriate aliases are added to the device tree and kernel support is fixed. Signed-off-by: Scott Wood <scottwood@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* common/board_f.c: modify the macro to use get_clocks() more commonGong Qianyu2015-10-241-0/+1
| | | | | | get_clocks() should not be limited by ESDHC. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
* arm, powerpc: select SYS_GENERIC_BOARDMasahiro Yamada2015-10-241-1/+0
| | | | | | | | | | | We have finished Generic Board conversion for ARM and PowerPC, i.e. all the boards have been converted except OpenRISC, SuperH, SPARC, which have not supported Generic Board framework yet. Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro defines in include/configs/*.h. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* configs: ls1021atwr: Enable DSPI for LS1021ATWRYao Yuan2015-10-111-1/+5
| | | | | | | DSPI2 can be verified when boot from QSPI now. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* I2C: mxc_i2c: make I2C1 and I2C2 optionalAlbert ARIBAUD \\(3ADEV\\)2015-10-021-0/+2
| | | | | | | | | | | | | | | | | | | The driver assumed that I2C1 and I2C2 were always enabled, and if they were not, then an asynchronous abort was (silently) raised, to be caught much later on in the Linux kernel. Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4 are. To make the change binary-invariant, declare I2C1 and I2C2 in every include/configs/ file which defines CONFIG_SYS_I2C_MXC. Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed (CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE) config options. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
* arm/ls102xa:add hwconfig setting to support disable unused devicesZhuoyu Zhang2015-09-011-1/+3
| | | | | | | | | | | | | | DEVDISRn registers provides a mechanism for gating clocks of IP blocks that are not used. Here we implement hwconfig option to allow users to disable unused peripherals on the board. For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts, User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma" in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to save more power. Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* net: Move CONFIG_E1000 options to KconfigSimon Glass2015-08-211-1/+0
| | | | | | | | Move config for the E1000 Ethernet driver to Kconfig and tidy up affected boards. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* armv7/ls1021atwr: added deep sleep support in ubootTang Yuantian2015-08-031-1/+10
| | | | | | Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv7/lS1021atwr: Enable bootscript for secure bootgaurav rana2015-08-031-0/+1
| | | | | | | | Enable bootscript support in secure boot for establishing chain of trust on LS1021atwr. Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv7/ls1021a: Reserve secure code into RAM instead of OCRAMZhuoyu Zhang2015-08-031-1/+0
| | | | | | | | | For ls1021a, Reserve secure code in to memory in case OCRAM is needed by other usage. Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls1021atwr: Enable USB IP supportRamneek Mehresh2015-07-221-0/+38
| | | | | | | Enable USB IP support for both EHCI and XHCI for ls1021atwr platform Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* arm/ls102xa: Add PSCI support for ls102xaWang Dongsheng2015-07-201-0/+2
| | | | | | | | | | | | Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform. Tested on LS1021AQDS, LS1021ATWR. Test CPU hotplug times: 60K Test kernel boot times: 1.2K Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Enable Driver Model SPI for ls1021atwrHaikun Wang2015-06-301-2/+7
| | | | | | | | | | | | Enable Driver Model SPI for ls1021atwr board. DSPI and QSPI only be enabled when boot from QSPI. DSPI and QSPI are compatible under Driver Model SPI. Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com> Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com> Tested-by: Haikun Wang <haikun.wang@freescale.com> Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-251-9/+0
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* Move default y configs out of arch/board KconfigJoe Hershberger2015-06-251-1/+0
| | | | | | | | | | | | | | | | | | | Some archs/boards specify their own default by pre-defining the config which causes the Kconfig system to mix up the order of the configs in the defconfigs... This will cause merge pain if allowed to proliferate. Remove the configs that behave this way from the archs. A few configs still remain, but that is because they only exist as defaults and do not have a proper Kconfig entry. Those appear to be: SPIFLASH DISPLAY_BOARDINFO Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates, drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM] Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: remove CONFIG_NET_MULTILars Poeschel2015-06-021-1/+0
| | | | | | | | | CONFIG_NET_MULTI is not used anywhere and thus can safely be removed from the configs. Acked-by: Marek Vasut <marex@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
* net: Move the CMD_NET config to defconfigsJoe Hershberger2015-06-011-2/+0
| | | | | | | | | | | This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* arm/ls1021a: Remove ccsr_ddr from immap_ls102xa.hYork Sun2015-05-201-0/+23
| | | | | | | | | ccsr_ddr structure is already defined in fsl_immap.h. Remove this duplicated define. Move fixed timing into ls1021atwr.h. Signed-off-by: York Sun <yorksun@freescale.com> CC: Alison Wang <alison.wang@freescale.com> Acked-by: Alison Wang <alison.wang@freescale.com>
* arm: ls102xa: Adjust the load address of U-Boot for NOR bootAlison Wang2015-05-201-1/+1
| | | | | | | | | | | | | | | | | | | The original load address of U-Boot is 0x67f80000. The address space of NOR flash is 0x60000000 to 0x67ffffff. It will cause the size of u-boot couldn't be larger than 512K. As more features are supported in u-boot, the size of u-boot is larger than 512K. To fix this issue, the load address of U-Boot for NOR boot is adjusted to 0x60100000. In RCW, the PBI command needs to change as follows: .pbi -write 0xee0200, 0x67f80000 +write 0xee0200, 0x60100000 .end Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* driver/i2c/mxc: Enable I2C bus 3 and 4York Sun2015-04-231-0/+1
| | | | | | | | | Some SoCs have more than two I2C busses. Instead of adding ifdef to the driver, macros are put into board header file where CONFIG_SYS_I2C_MXC is defined. Signed-off-by: York Sun <yorksun@freescale.com> CC: Heiko Schocher <hs@denx.de>
* arm/ls1021a: add PCIe settingsMinghuan Lian2015-02-241-0/+24
| | | | | | | | The patch enables and adds PCIe settings for boards LS1021AQDS and LS1021ATWR. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add LPUART support for LS1021ATWR boardAlison Wang2015-01-231-0/+12
| | | | | | | | This patch adds LPUART support for LS1021ATWR board. For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ARM: ls102xa: Setting device's stream id for SMMUs.Xiubo Li2014-12-111-0/+2
| | | | | | | | | | | | LS1 has 4 SMMUs for address translation of the masters. All the SMMUs' stream IDs are 8-bit. The address translation depends on the stream ID of the incoming transaction. Each master has unique stream ID assigned to it and is configurable through SCFG registers. The stream ID for the masters is identical and share the same register field of STREAM ID registers. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ARM: ls102xa: allow all the peripheral access permission as R/W.Xiubo Li2014-12-111-0/+1
| | | | | | | | | | | | | | | The Central Security Unit (CSU) allows secure world software to change the default access control policies of peripherals/bus slaves, determining which bus masters may access them. This allows peripherals to be separated into distinct security domains. Combined with SMMU configuration of the system masters privileges, these features provide protection against indirect unauthorized access to data. For now we configure all the peripheral access permissions as R/W. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls102xa: changing a few targets' configurations.Xiubo Li2014-12-111-0/+7
| | | | | | | | | Enable hypervisors utilizing the ARMv7 virtualization extension on the LS1021A-QDS/TWR boards with the A7 core tile, we add the required configuration variable. Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add QSPI boot support for LS1021AQDS/TWR boardAlison Wang2014-12-111-0/+28
| | | | | | | | | This patch adds QSPI boot support for LS1021AQDS/TWR board. The QSPI boot image need to be programmed into the QSPI flash first. Then the booting will start from QSPI memory space. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Fix SD/NAND/QSPI boot defination error for QE supportAlison Wang2014-12-111-1/+2
| | | | | | | | The SD/NAND/QSPI boot definations are wrong for QE support, this patch is to fix this error. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls1021a: Add CONFIG_DOS_PARTITION and CONFIG_CMD_FAT supportAlison Wang2014-12-111-0/+3
| | | | | | | | This patch will fix the bug that the partitions on the SD card could not be accessed and add the support for the FAT fs. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Add SD boot support for LS1021ATWR boardAlison Wang2014-12-111-0/+44
| | | | | | | | | | | | This patch adds SD boot support for LS1021ATWR board. SPL framework is used. PBL initialize the internal RAM and copy SPL to it, then SPL initialize DDR using SPD and copy u-boot from SD card to DDR, finally SPL transfer control to u-boot. Signed-off-by: Chen Lu <chen.lu@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Signed-off-by: Jason Jin <jason.jin@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* arm: ls102xa: Update PCIe dts node statusMinghuan Lian2014-12-111-0/+7
| | | | | | | | The patch changes PCIe dts node status to 'disabled' if the corresponding controller is disabled according to serdes protocol. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2014-11-261-0/+18
|\
| * arm: ls102xa: Add SystemID EEPROM support for LS1021ATWR boardAlison Wang2014-11-241-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SystemID information could be read through I2C1 from EEPROM on LS1021ATWR board. As LS1 is a little-endian processor, getting the version ID by be32_to_cpu() is wrong. Fix it by using e.version directly. This change will be compatible for both ARM and PowerPC. As there is an errata that I2C1 could not work in SD boot, reading EEPROM through I2C1 is disabled too in SD boot. Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * ls102xa: ifc: nor: fix the write issue when bytes unalignedYuan Yao2014-11-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Add define CONFIG_SYS_WRITE_SWAPPED_DATA. For LS1021AQDS and LS1021QTWR nor flash write should swap the bytes when handle unaligned tail bytes. Because of the ending, if the date bus width is 16-bits and the number of bytes is odd, we should swap the byte when write the last one. Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * qe: add qe support for ls1021a-twr boardZhao Qiang2014-11-191-0/+6
| | | | | | | | | | Signed-off-by: Zhao Qiang <B45475@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | config: remove redundant CONFIG_SYS_PROMPT definesMasahiro Yamada2014-11-231-1/+0
|/ | | | | | | | Since commit 0defddc851ed (config: Add a default CONFIG_SYS_PROMPT), each board header does not need to define CONFIG_SYS_PROMPT as long as it uses the default prompt "=> ". Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* kconfig: move CONFIG_SYS_HZ to lib/KconfigMasahiro Yamada2014-10-231-1/+0
| | | | | | | | | | | | CONFIG_SYS_HZ is always defined as 1000 in config_fallbacks.h (but some boards still have redundant definitions). This commit moves the definition and the document in README to Kconfig. Since lib/Kconfig can assure that CONFIG_SYS_HZ is 1000, the sanity check in lib/time.c should be removed. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Marek Vasut <marex@denx.de>
* ls102x: Add support for secure boot and enable blob commandRuchika Gupta2014-10-161-0/+4
| | | | | Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls102x: configs - Add hash command in freescale LS1 platformsRuchika Gupta2014-10-161-0/+8
| | | | | | | | | Hardware accelerated support for SHA-1 and SHA-256 has been added. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* ls102xa: dcu: Add platform support for DCU on LS1021ATWR boardWang Huan2014-09-081-0/+18
| | | | | | | This patch adds the TWR_LCD_RGB card/HDMI options and the common configuration for DCU on LS1021ATWR board. Signed-off-by: Alison Wang <alison.wang@freescale.com>
* arm: ls102xa: Add basic support for LS1021ATWR boardWang Huan2014-09-081-0/+273
LS102xA is an ARMv7 implementation. This patch is to add basic support for LS1021ATWR board. One DDR controller DUART1 is used as the console For the detail board information, please refer to README. Signed-off-by: Chen Lu <chen.lu@freescale.com> Signed-off-by: Yuan Yao <yao.yuan@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com>
OpenPOWER on IntegriCloud