summaryrefslogtreecommitdiffstats
path: root/include/configs/am335x_evm.h
Commit message (Collapse)AuthorAgeFilesLines
* am335x_evm: Switch to zImage as default rather than uImageTom Rini2013-10-071-11/+11
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm.h: If mmcdev and bootpart switch to mmcdev 1, so should mmcroot.Robert P. J. Day2013-09-201-0/+1
| | | | | | | | If, in CONFIG_BOOTCOMMAND, the environment switches both the mmcdev and bootpart variables to refer to MMC device 1, it would make sense that the mmcroot env variable should switch to that device as well. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* am335x_evm: am33xx_spl_board_init function and scale core frequencyTom Rini2013-09-201-0/+5
| | | | | | | | | | | | | | | Add a am33xx_spl_board_init (and enable the PMICs) that we may see, depending on the board we are running on. In all cases, we see if we can rely on the efuse_sma register to tell us the maximum speed. In the case of Beaglebone White, we need to make sure we are on AC power, and are on later than rev A1, and then we can ramp up to the PG1.0 maximum of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we need to rely on the efuse_sma if we are on PG2.1, and the defaults for PG1.0/2.0. Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-09-061-41/+52
|\
| * am335x_evm: Regroup USB optionsTom Rini2013-08-281-39/+41
| | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| * am335x_evm: Add comment by SPL SPI supportTom Rini2013-08-281-0/+2
| | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| * TI:am335x: Better comment and organize the networking related optionsTom Rini2013-08-281-2/+9
| | | | | | | | | | | | While in here, drop CONFIG_BOOTP_DEFAULT as it is unused in the code. Signed-off-by: Tom Rini <trini@ti.com>
* | am335x_evm.h: Add back the actual load of the kernel imageRobert P. J. Day2013-09-061-1/+3
|/ | | | | | | Somewhere along the line of refactoring the am335x header files, the kernel image load was lost, so put it back in. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xxTom Rini2013-08-151-218/+18
| | | | | | | | | | | We create two new files, include/configs/ti_armv7_common.h for all of the common IP blocks and related features / commands we share in virtually all of our platforms. We then create include/configs/ti_am335x_common.h for everything common to the am335x SoC leaving just the board specific parts to include/configs/ti_am335x_common.h. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Bring in 'boot_fdt' logic from i.MXTom Rini2013-08-151-5/+16
| | | | | | | Bring in the 'boot_fdt' environment variable that i.MX boards use to try and load a device tree when booting. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Use default baud rate tableTom Rini2013-08-151-2/+0
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP: Add CONFIG_OMAP_COMMONLokesh Vutla2013-08-151-0/+1
| | | | | | | Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* am335x_evm: Add support for eMMC environmentJustin Waters2013-07-301-1/+6
| | | | | | | | | Some boards, such as the BeagleBone Black, have an eMMC chip intstead of NAND. We can use the eMMC boot partition to store the environment, since it isn't used for anything else. This allows us to have a configurable environment on those boards. Signed-off-by: Justin Waters <justin.waters@timesys.com>
* am335x_evm: Rework bootcmd to handle two MMC devsJustin Waters2013-07-301-20/+22
| | | | | | | | | | | | | | | The BeagleBone Black can boot from either the MMC card or eMMC chip on board. We should try both interfaces. This modification also allows a graceful fallback if a device exists but boot images are not present on it. Changes for v2: * Fix boot partition - it should always show up as mmcblk0p2 * Fix missing FDT load Signed-off-by: Justin Waters <justin.waters@timesys.com>
* am335x_evm: Add command line editingJustin Waters2013-07-301-0/+3
| | | | | | | | | Many modern U-Boot ports enable command line editing and a history buffer. The am335x_evm configuration is fairly comprehensive as it is, so a few extra kb should not be noticable, and it adds a very convenient feature. Signed-off-by: Justin Waters <justin.waters@timesys.com>
* am335x_evm: Make NAND support modularJustin Waters2013-07-301-19/+32
| | | | | | | | | | Give the user the ability to disable NAND support by defining CONFIG_NO_NAND. This will allow custom hardware to easily support this configuration. Signed-off-by: Justin Waters <justin.waters@timesys.com> [trini: Make apply on top of other series] Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add support to boot from NOR.Steve Kipisz2013-07-301-2/+24
| | | | | | | | | | | | | | | | | | NOR requires that s_init be within the first 4KiB of the image so that we can perform the rest of the required pinmuxing to talk with the rest of NOR that we are found on. When NOR_BOOT is set we save our environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid using SPL for this case and u-boot.bin is written directly to the start of NOR. We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c with TI81xx checks as at this time U-Boot does not discard unused sections in the main build and this code relies on functions specific to (and only provided in) ti81xx-related code. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add support for the NOR module on the memory capeSteve Kipisz2013-07-301-0/+28
| | | | | | | | | | | This patch adds support for the NOR module that attaches to the memory cape for a Beaglebone board. This does not add booting support; only support so that you can boot from SD/MMC and see the NOR module so that it can be programmed. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> [trini: Clean up config changes slightly] Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Update SPI_BOOT support, add MTDPARTS infoTom Rini2013-07-301-21/+26
| | | | | | | | | | | - Style cleanup (# define -> #define) - Due to ROM issues, redudant loading isn't feasible, so drop. - Given extra space, increase max size of U-Boot to 512KiB - Correct env size to match usage (we had not re-defined ENV_SIZE). - Given extra space, keep env size as 128KiB, add redundant environment. Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Drop useless CONFIG_ENV_IS_NOWHERETom Rini2013-07-301-4/+0
| | | | | | | | We always set a CONFIG_ENV_IS_...somewhere... so drop the initial define of NOWHERE. Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Correct CONFIG_CMD_SPL_WRITE_SIZETom Rini2013-07-261-1/+1
| | | | | | | | We use CONFIG_CMD_SPL_WRITE_SIZE when reading/writing the args portion of falcon mode to NAND. Previously it was half the size of the eraseblock which is too small, increase to eraseblock size. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Update eMMC falcon mode locationsTom Rini2013-07-261-3/+3
| | | | | | | | | | | The previous location used for the "args" portion of falcon mode was too small to allow for a device tree to be saved there, so move the location slightly and increase the size. In addition, our previous kernel location was part of the area we set aside for U-Boot itself, so move it up a bit higher. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
* am335x_evm: Correct DFU ALT settings for falcon modeTom Rini2013-07-261-3/+8
| | | | | | | | | | Now that we have falcon mode enabled, the partiton numbers for NAND have changed, and we need to list entries for updating these parts of the system. While adding falcon mode entires for eMMC (raw), we round up the limit on U-Boot for ease of math later. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
* am335x_evm: Add missing ';' in findfdtTom Rini2013-06-271-1/+1
| | | | | | | | In a714321 we add a check at the end of findfdt to make sure we have updated it from undefined and if not, warn the user. This however forgot a ';' on the end of the previous last test. Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-06-221-3/+4
|\
| * arm: omap: Add check for fdtfile in the findfdt macroDan Murphy2013-06-181-3/+4
| | | | | | | | | | | | | | | | | | In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is defined after the findfdt macro has run. If the file is not defined then warn the user that the dtb file is not defined. Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* | common/Makefile: Add new symbol CONFIG_SPL_ENV_SUPPORT for environment in SPLYing Zhang2013-06-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | There will need the environment in SPL for reasons other than network support (in particular, hwconfig contains info for how to set up DDR). Add a new symbol CONFIG_SPL_ENV_SUPPORT to replace CONFIG_SPL_NET_SUPPORT for environment in common/Makefile. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | am335x: enable falcon boot mode for mmc (raw and fat) and nandPeter Korsgaard2013-06-071-3/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Jump into full u-boot mode if a 'c' character is received on the uart. We need to adjust the spl bss/malloc area to not overlap with the loadaddr of the kernel (sdram + 32k), so move it past u-boot instead. For raw mmc, we store the kernel parameter area in the free space after the MBR (if used). For nand, we use the last sector of the partition reserved for u-boot. This also enables the spl command in the full u-boot so the kernel parameter area snapshot can be created. Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
* | am33xx/omap4+: Move SRAM_SCRATCH_SPACE_ADDR to <asm/arch/omap.h>Tom Rini2013-06-061-3/+2
|/ | | | | | | | | | The location of valid scratch space is dependent on SoC, so move that there. On OMAP4+ we continue to use SRAM_SCRATCH_SPACE_ADDR. On am33xx/ti814x we want to use what the ROM defines as "public stack" which is the area after our defined download image space. Correct the comment about and location of CONFIG_SPL_TEXT_BASE. Signed-off-by: Tom Rini <trini@ti.com>
* am33xx: Correct NON_SECURE_SRAM_START/ENDTom Rini2013-06-041-2/+8
| | | | | | | | | | | | | | | | | | | Prior to Sricharan's cleanup of the boot parameter saving code, we did not make use of NON_SECURE_SRAM_START on am33xx, so it wasn't a problem that the address was pointing to the middle of our running SPL. Correct to point to the base location of the download image area. Increase CONFIG_SPL_TEXT_BASE to account for this scratch area being used. As part of correcting these tests, make use of the fact that we've always been placing our stack outside of the download image area (which is fine, once the downloaded image is run, ROM is gone) so correct the max size test to be the ROM defined top of the download area to where we link/load at. Signed-off-by: Tom Rini <trini@ti.com> --- Changes in v2: - Fix typo noted by Peter Korsgaard
* ARM: OMAP: Add arch_cpu_init functionSRICHARAN R2013-05-101-0/+3
| | | | | | | | | | | | The boot parameters passed from SPL to UBOOT must be saved as a part of uboot's gd data as early as possible, before we will inadvertently overwrite it. So adding a arch_cpu_init for the required Socs to save it. Signed-off-by: Sricharan R <r.sricharan@ti.com> [trini: Add igep0033 hunk] Signed-off-by: Tom Rini <trini@ti.com>
* ARM: OMAP: Cleanup boot parameters usageSRICHARAN R2013-05-101-0/+1
| | | | | | | | | | | The boot parameters are read from individual variables assigned for each of them. This been corrected and now they are stored as a part of the global data 'gd' structure. So read them from 'gd' instead. Signed-off-by: Sricharan R <r.sricharan@ti.com> [trini: Add igep0033 hunk] Signed-off-by: Tom Rini <trini@ti.com>
* Remove duplicate / unused #defines on AM335x boardsMark Jackson2013-05-101-8/+2
| | | | | | | | | | | | | As part of a review of a recent patch to add a new AM335x board, Tom found several duplicate and/or unused #defines. This patch simply removes them. The two affected configs have been recompiled to check nothing was broken (from a compilation point of view !!) Reported-by: Tom Rini <trini@ti.com> Signed-off-by: Mark Jackson <mpfj-list@mimc.co.uk>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-121-2/+50
|\ | | | | | | | | Conflicts: drivers/video/exynos_fb.c
| * am335x_evm: Enable DFU for NAND and MMC, provide example alt_infosPantelis Antoniou2013-04-101-2/+39
| | | | | | | | | | | | | | | | | | | | | | | | - Add CONFIG_DFU_NAND, CONFIG_DFU_MMC - Set dfu_alt_info_nand, dfu_alt_info_emmc and dfu_alt_info_mmc to show working examples for those cases. - Increase CONFIG_SYS_MAXARGS due to hush parsing bugs that would otherwise disallow 'setenv dfu_alt_info ${dfu_alt_info_nand}'. - Enable CONFIG_FAT_WRITE to allow updating on MMC Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
| * am335x_evm: Add CONFIG_CMD_MTDPARTS and relevant defaultsTom Rini2013-04-101-0/+9
| | | | | | | | Signed-off-by: Tom Rini <trini@ti.com>
| * am335x_evm: Define CONFIG_SYS_CACHELINE_SIZEPantelis Antoniou2013-04-101-0/+2
| | | | | | | | | | | | | | | | drivers/usb/gadget/composite.c requires that this is defined early. Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Tom Rini <trini@ti.com>
* | musb: am335x: disable bulk split-combine featureBin Liu2013-04-081-0/+1
|/ | | | | | | | | | | | | | | | | | | On TI AM335x devices, MUSB has bulk split/combine feature enabled in the ConfigData register, but the current MUSB driver does not support it yet. Therefore, disable the feature for now, until the driver adds the support. One usecase which is broken because of this feature is that Ether gadget stops working in Fullspeed mode (by un-defining CONFIG_USB_GADGET_DUALSPEED) After desabled this feature, MUSB driver send packets in proper size (no more than 64 bytes) in Fullspeed mode. This has been validated with Ether gadget in Fullspeed mode on AM335x EVM. Signed-off-by: Bin Liu <b-liu@ti.com>
* am33xx: Add required includes to some omap/am33xx codeTom Rini2013-03-241-2/+1
| | | | | | | | | | | | | - In arch/arm/cpu/armv7/omap-common/timer.c, drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files that the driver needs but had been relying on <config.h> to bring in. - In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h> - In am335x_evm.h and pcm051.h don't globally include <asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h> as that is the only include which defines things the config uses. Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add more variables and switch to DT booting.Koen Kooi2013-03-221-5/+10
| | | | | | | | | | Make bootcmd run findfdt so that we know what dtb file to load. Add a loadfdt command to load this file in. Make mmcboot pass in ${fdtaddr} and make the mmc section of bootcmd run loadfdt. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
* am335x_evm: Enable CMD_EXT4 and CMD_FS_GENERIC, add bootpart to envKoen Kooi2013-03-221-4/+6
| | | | | | | | | | | The kernel is loaded from some form of ext[234] or FAT, depending on the distribution used. We add a bootpart variable to the environment so that we can load from the correct mmc partition as well. We leave CONFIG_CMD_EXT2 for existing scripts that use ext2load. Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
* am335x_evm: add support for BeagleBone Black DT nameKoen Kooi2013-03-221-0/+2
| | | | | | | | | | Cc: Matt Porter <mporter@ti.com> Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Koen Kooi <koen@dominion.thruhere.net> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Matt Porter <mporter@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Nishanth Menon <nm@ti.com>
* Remove linker lists (LGAs) from SPL linker scriptsAlbert ARIBAUD2013-03-121-1/+1
| | | | | | | | | | | | Many SPL linker scripts needlessly include linker lists (aka LGAs). Remove them whenever possible; keep it only in the seven am335x_evm variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot), where there is actual content in output section .u_boot_list. This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets byte-identical. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* am335x_evm: Enable CONFIG_CMD_BOOTZTom Rini2013-03-111-0/+1
| | | | | | | | | | With v3.9 and later of the Linux Kernel defaulting to multi-platform images with omap2plus_defconfig, uImage isn't builtable anymore by default. Add CONFIG_CMD_BOOTZ so that we can still boot something the kernel spits out. Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
* am335x_evm: Add am335x_evm_usbspl build targetTom Rini2013-03-081-3/+1
| | | | | | | We add USB (RNDIS gadget) SPL support as a separate target. We need to pull out YMODEM support in order to be a small enough target binary. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Never set CONFIG_EXTRA_ENV_SETTINGS in SPLTom Rini2013-03-081-1/+3
| | | | | | | | | | Because of our support for network-based SPL, we don't discard all of the environment related functions. We however never make use of the default CONFIG_EXTRA_ENV_SETTINGS items and as this variable grows, it brings us closer to (or with some toolchains, over) our SPL size limit. Never set this in the case of SPL. Signed-off-by: Tom Rini <trini@ti.com>
* am335x evm: Add am335x_evm_spiboot targetTom Rini2013-02-181-2/+23
| | | | | | | | This target will move the environment into SPI flash and documents the expected layout. We correct the SPL define for where U-Boot is and remove an unused define. Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add NET environment variablesChase Maupin2013-02-181-0/+15
| | | | | | | * Add environment variables to support network booting Signed-off-by: Chase Maupin <Chase.Maupin@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add SPI environment variablesChase Maupin2013-02-181-0/+14
| | | | | | | | * Added variables to support SPI booting * Note that the first 512KiB are reserved for 4 copies of SPL. Signed-off-by: Chase Maupin <Chase.Maupin@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add NAND environment variablesChase Maupin2013-02-181-0/+14
| | | | | | | | | * Added support to the default environment variables for NAND boot. * Add nandboot to the default bootcmd. Signed-off-by: Chase Maupin <Chase.Maupin@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
OpenPOWER on IntegriCloud