summaryrefslogtreecommitdiffstats
path: root/include/configs/T104xRDB.h
Commit message (Collapse)AuthorAgeFilesLines
* nand: Remove CONFIG_MTD_NAND_VERIFY_WRITEPeter Tyser2015-03-301-1/+0
| | | | | | | | | The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some time and a more generic method of NAND verification now exists in U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Tested-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* mpc85xx/t104xrdb : remove raw timing parametervijay rai2015-03-051-1/+0
| | | | | | | | This board uses DDR DIMM. Reading SPD provides more flexibility. Raw timing parameter code should be removed after debugging. Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/T1040rdb: Add VSC9953 support for T1040rdb boardCodrin Ciubotariu2015-01-211-0/+8
| | | | | | | | This patch configures and initializes the L2 switch on T1040rdb board. The external L2 switch ports may be connected to PHYs only over QSGMII, for T1040rdb. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
* mpc85xx/t104xrdb: convert deep sleep to generic board interfaceTang Yuantian2014-12-151-0/+3
| | | | | | | | A new interface is introduced to support generic board structure. Converts it to use new interface. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/T10xx: Fix number of portalsJeffrey Ladouceur2014-12-151-2/+2
| | | | | | | | | | | Following boards has incorrect number of portals defined. powerpc/T102xQDS powerpc/T102xRDB powerpc/T1040QDS powerpc/T104xRDB Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: inhibit qman and bman portals by defaultJeffrey Ladouceur2014-12-151-0/+16
| | | | | | | | | Not all portals might be managed and therefore visible. Set the isdr register so that the corresponding isr register won't be set. This is required when supporting power management. Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t104x: Convert to use generic board codevijay rai2014-12-051-0/+2
| | | | | | | Convert T1040QDS and T1040RDB to use generic board code. Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx:Put errata number for T104x NAND boot issuePrabhakar Kushwaha2014-12-051-1/+9
| | | | | | | | | | | | When device is configured to load RCW from NAND flash IFC_A[16:31] are driven low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using IFC_A[16:31] lines are not accessible. Workaround is already in-place. Put the errata number to adhere errata handling framework. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* config: remove redundant CONFIG_SYS_PROMPT definesMasahiro Yamada2014-11-231-1/+0
| | | | | | | | Since commit 0defddc851ed (config: Add a default CONFIG_SYS_PROMPT), each board header does not need to define CONFIG_SYS_PROMPT as long as it uses the default prompt "=> ". Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* mpc85xx: configs - Enable blob command in freescale platformsRuchika Gupta2014-10-161-0/+1
| | | | | | | | Enable blob commands for platforms having SEC 4.0 or greater for secure boot scenarios Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: configs - Add hash command in freescale platformsRuchika Gupta2014-10-161-0/+7
| | | | | | | | | Enable CAAM in platforms supporting the hardware block. Hash command enabled along with hardware accelerated support for SHA-1 and SHA-256 for platforms which have CAAM block. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-09-261-8/+12
|\
| * powerpc/t104xrdb: Add T1042RDB board supportvijay rai2014-09-241-8/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T1042RDB is a Freescale reference board that hosts the T1042 SoC (and variants). The board is similar to T1040RDB, T1042 is a reduced personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch). T1042RDB is configured with serdes protocol 0x86 which can support following interfaces - 2 RGMII's on DTSEC4, DTSEC5 - 1 SGMII on DTSEC3 DTSEC1, DTSEC2 are not connected on board. This Patch - add T1042RDB support - updates README file for T1042RDB details and update commands for switching to alternate banks from vBank0 to vBank4 and vice versa This patch also does minor clean ups for fdt defines for T1042RDB and T1042RDB_PI board Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t104xrdb: Add Support of rcw for T1042RDB in u-bootvijay rai2014-09-241-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | This patch adds support of rcw for T1042RDB, it makes following changes : - Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB - Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates comments for valid serdes protocol which is 0x06 - Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | powerpc/t104xrdb: Enable SPI flash Extend address supportZhiqiang Hou2014-09-251-0/+1
|/ | | | | | | Enable the Extend address to support SPI flash more than 16MB. Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
* powerpc/t104xrdb: support deep sleep in SPI/SD bootTang Yuantian2014-08-121-9/+9
| | | | | | | | | | | | Add deep sleep support in SPI/SD boot. The destination address second stage uboot image is loaded to is changed because currently this address will be used by kernel which means we can't reserve it for resume. Entry point to kernel is still placed in second stage uboot. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t1042RDB: Add Video - HDMI supportJason Jin2014-08-121-0/+32
| | | | | | | | | | | | | | | | | | | | | | | T1042 has internal display interface unit (DIU) for driving video. T1042RDB supports video mode via -LCD using TI enconder -HDMI type interface via HDMI encoder Chrontel, CH7301C encoder which is I2C programmable is used as HDMI connector on T1042RDB. This patch add support to -enable Video interface for T1042RDB -route qixis multiplexing to enable DIU-HDMI interface on board -program DIU pixel clock gerenartor for T1042 -program HDMI encoder via I2C on board This patch refer to the upstream diu patch (337b0c52b3296f371d04aef71a833e09110e0e6b) for T1040qds. Signed-off-by: Jason Jin <Jason.Jin@freescale.com> Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com> [York Sun: resolve conflict and move changes to T104xRDB.h] Reviewed-by: York Sun <yorksun@freescale.com>
* include: remove CONFIG_SPL/CONFIG_TPL definition in config headersMasahiro Yamada2014-07-301-1/+0
| | | | | | | | | Now CONFIG_SPL and CONFIG_TPL are defined in Kconfig. Remove the redundant definition in config headers. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* include: define CONFIG_SPL and CONFIG_TPL as 1Masahiro Yamada2014-07-301-1/+1
| | | | | | | | | | | | | | | | We are about to switch to Kconfig in the next commit. But there are something to get done beforehand. In Kconfig, include/generated/autoconf.h defines boolean CONFIG macros as 1. CONFIG_SPL and CONFIG_TPL, if defined, must be set to 1. Otherwise, when switching to Kconfig, the build log would be sprinkled with warning messages like this: warning: "CONFIG_SPL" redefined [enabled by default] Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* powerpc/t1040: update i2c for t1040qds and t104xrdbShengzhou Liu2014-07-221-2/+8
| | | | | | | | - Fix base address of I2C2 as 0x118100 instead of 0x119000. - Add definitions for I2C3 & I2C4. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/ifc: fix invalid CSn FTIM2.TCH settingShaohui Xie2014-07-221-1/+1
| | | | | | | | | On some platforms, CSn FTIM2.TCH is set to zero which is invalid, an invalid hold time makes DUT timing variances, whether it works or not on luck. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx: Add workaround to enable TDM on T1040Sandeep Singh2014-06-051-0/+6
| | | | | | | | | | | | | | | This is a workaround for 32 bit hardware limitation of TDM. T1040 has 36 bit physical addressing, TDM DMAC register are 32 bit wide but need to store address of CCSR space which lies beyond 32 bit address range. This workaround creats a LAW to enable access of TDM DMA to CCSR by mapping CCSR to overlap with DDR. A hole of 16M is created in memory using device tree. This workaround law is set only if "tdm" is defined in hwconfig. Also disable POST tests and add LIODN for TDM Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: configs: remove c=ffe from default environmentKim Phillips2014-05-161-2/+1
| | | | | | | | | | | AFAICT, c=ffe does nothing and was a typo from the original commit d17123696c6180ac8b74fbd318bf14652623e982 "powerpc/p4080: Add support for the P4080DS board" and just kept on getting duplicated in subsequently added board config files. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Edward Swarthout <ed.swarthout@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/mpc85xx:Update MONITOR_LEN for 768KB u-boot sizePrabhakar Kushwaha2014-04-221-1/+1
| | | | | | | | | U-boot binary size has been increased from 512KB to 768KB. So update CONFIG_SYS_MONITOR_LEN to reflect the same. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t104xrdb: Add support of NAND, SD, SPI boot for T104xRDBPrabhakar Kushwaha2014-04-221-17/+109
| | | | | | | | | | | | | | Add support of 2 stage NAND, SD, SPI boot loader using SPL framework. here, PBL initialise the internal SRAM and copy SPL(160KB). This further initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR. Finally SPL transer control to u-boot. Initialise/create followings required for SPL framework - Add spl.c which defines board_init_f, board_init_r - update tlb and ddr accordingly Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t1042rdb_pi: Disable CONFIG_QE and CONFIG_U_QEPrabhakar Kushwaha2014-04-221-0/+2
| | | | | | | | | T1042RDB_PI board does not have QE connector. So disable CONFIG_QE and CONFIG_U_QE for T1042RDB_PI Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* mpc85xx: Add deep sleep support on T104xRDBTang Yuantian2014-04-221-0/+4
| | | | | | | Add deep sleep support on T104xRDB platforms. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* board/t104xrdb: Add support of CPLDPrabhakar Kushwaha2014-04-221-0/+8
| | | | | | | | | | | T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features. This support of CPLD includes - files and register defintion - Commands to swtich alternate bank and default bank Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/T1040: add mtdparts suppport for T104xRDB and T1040QDSPrabhakar Kushwaha2014-04-221-0/+17
| | | | | | | | We use dynamical mtdparts partition instead of directly puting mtd partitions nodes in device tree. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t104xrdb: Unification of T104xRDB header filesvijay rai2014-04-221-0/+700
T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB. T104xRDB header file can support both T1040RDB and T1042RDB_PI header. Patch makes following changes -Update Boards.cfg file for T1040RDB and T1042RDB_PI -Add new T104xRDB header file -Delete T1040RDB, T1042RDB_PI header file Signed-off-by: Vijay Rai <vijay.rai@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
OpenPOWER on IntegriCloud