summaryrefslogtreecommitdiffstats
path: root/include/configs/MPC8360EMDS.h
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/mpc83xx: increment malloc heap sizeKim Phillips2012-07-031-1/+1
| | | | | | | | | | extention of commit 3b6b256 "powerpc/mpc83xx: increment malloc heap size for the MPC832x MDS boards" to all other mpc83xx based boards. It fixes "Unable to save the rest of sector" messages when trying to save the environment to flash. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-201-3/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* powerpc/mpc83xx: Add 33.33MHz support for mpc8360emdsJerry Huang2011-11-071-0/+27
| | | | | | | | The new MPC8360EMDS board changes the oscillator to 33.33MHz in order to support QE 500MHz since 2008. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/mpc83xx: Add 512MB DDR support for mpc8360emdsJerry Huang2011-11-031-1/+2
| | | | | | | | | | | | | | | | | The new MPC8360EMDS board supports 512MB DDR since 2008. For 512MB DDR: BAT0 is used for the first 256MB memory, BAT4 is used for the second 256MB memory and the address space of SDRAM follows the DDR, so if the size of DDR is 256MB, the BAT4 will be used for SDRAM and if the size of DDR is 512MB, the BAT4 will be used for the second 256MB memory and there is no BAT for SDRAM. Therefore, if the size of DDR is 512MB, this patch will use BAT6 for SDRAM and BAT5 will be used for PCI MEM to replace the BAT6 after the codes relocates to the DDR. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> CC: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds codeJoe Hershberger2011-11-031-3/+4
| | | | | | | | | | | | | Rename CONFIG_SYS_DDR_CONFIG to include which CS it is configuring Cleanup the setting of the csnbds to respect the setting of CONFIG_SYS_DDR_SDRAM_BASE Use __ilog2 instead of writing the code to compute it Disable unused CS configs Ensure ddrlaw.bar is configured Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Cleanup usage of LBC constantsJoe Hershberger2011-11-031-22/+71
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Cleanup usage of BAT constantsJoe Hershberger2011-11-031-9/+9
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: cosmetic: MPC8360EMDS.h checkpatch complianceJoe Hershberger2011-11-031-82/+141
| | | | | | Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* board configs: drop NET_MULTI referencesMike Frysinger2011-10-051-5/+0
| | | | | | | Now that none of the core checks CONFIG_NET_MULTI, there's not much point in boards defining it. So scrub all references to it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* fsl: Change fsl_phy_enet_if to phy_interface_tAndy Fleming2011-04-201-2/+2
| | | | | | | | | | | | The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum. This meant that drivers which used fsl_phy_enet_if to deal with PHY interfaces would have to convert between the two (or we would have to have them mirror each other, and deal with the ensuing maintenance headache). Instead, we switch all clients of fsl_phy_enet_if over to phy_interface_t, which should become the standard, anyway. Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
* mpc83xx: Fix for MPC8360 ATM Quad OC3 External PhysStefan Popa2010-11-301-2/+2
| | | | | | | | Changed the CS4 and CS5 addresses on Local Bus for matching the PMC0 and PMC1 addresses. Signed-off-by: Stefan Popa <Stefan.Popa@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated valueWolfgang Denk2010-10-261-2/+1
| | | | | | | | | | | | | | | | | | CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not being able to use "sizeof(struct global_data)" in assembler files. Recent experience has shown that manual synchronization is not reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into GENERATED_GBL_DATA_SIZE which gets automatically generated by the asm-offsets tool. In the result, all definitions of this value can be deleted from the board config files. We have to make sure that all files that reference such data include the new <asm-offsets.h> file. No other changes have been done yet, but it is obvious that similar changes / simplifications can be done for other, related macro definitions as well. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Kumar Gala <galak@kernel.crashing.org>
* Rename CONFIG_SYS_INIT_RAM_END into CONFIG_SYS_INIT_RAM_SIZEWolfgang Denk2010-10-261-2/+2
| | | | | | | | | | | | | | | | | | CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be some end address; to make the meaning more clear we rename it into CONFIG_SYS_INIT_RAM_SIZE No other code changes are performed in this patch, only minor editing of white space (due to the changed length) and the comments was done, where noticed. Note that the code for the PATI and cmi_mpc5xx board configurations looks seriously broken. Last known maintainers on Cc: Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Denis Peter <d.peter@mpl.ch> Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch> Acked-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Cleanup BOOTFLAG_* referencesPeter Tyser2010-10-181-8/+0
| | | | | | | | | | | | Now that warm booting is not supported, there isn't a need for the BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them. Note that this change makes the board info bd_bootflags field useless. It will always be set to 0, but we leave it around so that we don't break the board info structure that some OSes are expecting to be passed from U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Makefile: move all Power Architecture boards into boards.cfgWolfgang Denk2010-10-181-0/+3
| | | | | | | | | | Clean up Makefile, and drop a lot of the config.mk files on the way. We now also automatically pick all boards that are listed in boards.cfg (and with all configurations), so we can drop the redundant entries from MAKEALL to avoid building these twice. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-181-1/+1
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* e300: increase CONFIG_SYS_BOOTMAPSZ to allow booting large kernelsIra W. Snyder2010-09-231-2/+2
| | | | | | | | | | | | | | Newer Linux kernels can overrun the initial memory window used for booting with their BSS area. When this happens, they overwrite the FDT and silently fail to boot. On e300 CPUs, the Linux kernel uses an initial BAT covering the first 256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value allowed by Linux. This will allow very large kernels to boot. Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Remove unused CONFIG_SERIAL_SOFTWARE_FIFO featureStefan Roese2010-09-231-1/+0
| | | | | | | | | This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO feature from U-Boot. It has only been implemented for PPC4xx and was not used at all. So let's remove it and make the code smaller and cleaner. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
* net: rename "FSL UECx" net interfaces "UECx"Kim Phillips2010-08-091-1/+1
| | | | | | | | | | continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8 "net ppc: fix ethernet device names with spaces" (currently in u-boot-net.git) for QE based parts. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* mpc83xx: turn on icache in core initialization to improve u-boot boot timeKim Phillips2010-04-221-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | before, MPC8349ITX boots u-boot in 4.3sec: column1 is elapsed time since first message column2 is elapsed time since previous message column3 is the message 0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX 0.000 0.000: 0.000 0.000: Reset Status: 0.000 0.000: 0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz 0.032 0.000: Board: Freescale MPC8349E-mITX 0.032 0.000: UPMA: Configured for compact flash 0.032 0.000: I2C: ready 0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz) 1.516 1.456: FLASH: 16 MB 2.641 1.125: PCI: Bus Dev VenId DevId Class Int 2.652 0.011: 00 10 1095 3114 0180 00 2.652 0.000: PCI: Bus Dev VenId DevId Class Int 2.652 0.000: In: serial 2.652 0.000: Out: serial 2.652 0.000: Err: serial 2.682 0.030: Board revision: 1.0 (PCF8475A) 3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic 3.080 0.000: TSEC0, TSEC1 4.300 1.219: IDE: Bus 0: .** Timeout ** after, MPC8349ITX boots u-boot in 3.0sec: 0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX 0.010 0.000: 0.010 0.000: Reset Status: 0.010 0.000: 0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz 0.017 0.000: Board: Freescale MPC8349E-mITX 0.038 0.020: UPMA: Configured for compact flash 0.038 0.000: I2C: ready 0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz) 0.260 0.222: FLASH: 16 MB 1.390 1.130: PCI: Bus Dev VenId DevId Class Int 1.390 0.000: 00 10 1095 3114 0180 00 1.390 0.000: PCI: Bus Dev VenId DevId Class Int 1.400 0.010: In: serial 1.400 0.000: Out: serial 1.400 0.000: Err: serial 1.400 0.000: Board revision: 1.0 (PCF8475A) 1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic 1.832 0.000: TSEC0, TSEC1 3.038 1.205: IDE: Bus 0: .** Timeout ** also tested on these boards (albeit with a less accurate boottime measurement method): seconds: before after 8349MDS ~2.6 ~2.2 8360MDS ~2.8 ~2.6 8313RDB ~2.5 ~2.3 #nand boot 837xRDB ~3.1 ~2.3 also tested on an 8323ERDB. v2: also remove the delayed icache enablement assumption in arch ppc's board.c, and add a CONFIG_MPC83xx define in the ITX config file for consistency (even though it was already being defined in 83xx' config.mk). Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: enable command line autocompletionKim Phillips2010-04-221-0/+1
| | | | | | because it's convenient. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: remove hardcoded network addresses from config filesKim Phillips2010-02-221-2/+0
| | | | | | | and avoid e.g., two identical boards from causing random networking conflicts when hooked up to the same network. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx, uec: split enet_interface in two variablesHeiko Schocher2010-01-311-2/+4
| | | | | | | | | | | | There's no sensible reason to unite speed and interface type into one variable. So split this variable enet_interface into two vars: enet_interface_type, which hold the interface type and speed. Also: add the possibility for switching between 10 and 100 MBit interfaces on the fly, when running in FAST_ETH mode. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfieldsKim Phillips2009-09-261-1/+2
| | | | | | | | | | | | | | | | | | | some LCRR bits are not documented throughout the 83xx family RMs. New board porters copying similar board configurations might omit setting e.g., DBYP since it was not documented in their SoC's RM. Prevent them bricking their board by retaining power on reset values in bit fields that the board porter doesn't explicitly configure via CONFIG_SYS_<registername>_<bitfield> assignments in the board config file. also move LCRR assignment to cpu_init_r[am] to help ensure no transactions are being executed via the local bus while CLKDIV is being modified. also start to use i/o accessors. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: mpc8360emds: Add QE USB device tree fixupsAnton Vorontsov2009-09-251-0/+2
| | | | | | | | With this patch we can change QE USB mode without need to hand-edit the device tree. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: mpc8360emds: Use RGMII-ID mode, add workarounds for rev. 2.1 CPUsAnton Vorontsov2009-09-251-2/+2
| | | | | | | | | This patch fixes various ethernet issues with gigabit links handling in U-Boot. The workarounds originally implemented by Kim Phillips for Linux kernel. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: accommodate larger kernel sizes by defaultKim Phillips2009-08-211-2/+2
| | | | | | | linux mpc83xx_defconfig kernels are getting bigger, accommodate for their growth by adjusting default load and fdt addresses. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: CONFIG_83XX_GENERIC_PCI is now synonymous with CONFIG_PCI; remove ↵Kim Phillips2009-07-271-1/+0
| | | | | | the former Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: convert all remaining boards over to 83XX_GENERIC_PCIKim Phillips2009-07-181-13/+15
| | | | Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: increase MONITOR_LEN to offset growing painsKim Phillips2009-07-141-1/+1
| | | | | | | | Saving the environment leads to overwriting u-boot itself, bricking boards. Increase u-boot's image size so the environment base address doesn't end up overlapping u-boot text. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Replace CONFIG_MPC83XX with CONFIG_MPC83xxPeter Tyser2009-06-121-1/+1
| | | | | | | | Use the standard lowercase "xx" capitalization that other Freescale architectures use for CPU defines to prevent confusion and errors Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Use common LSDMR defines from asm/fsl_lbc.hKumar Gala2009-03-301-22/+5
| | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENVMike Frysinger2009-02-181-1/+1
| | | | | | | | The CONFIG_CMD_ENV option controls enablement of the `saveenv` command rather than a generic "env" command, or anything else related to the environment. So, let's make sure the define is named accordingly. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* mpc83xx: mpc8360emds: rework LBC SDRAM setupAnton Vorontsov2008-10-211-14/+11
| | | | | | | | | | | | | | | | | | | Currently 64M of LBC SDRAM are mapped at 0xF0000000 which makes it difficult to use (b/c then the memory is discontinuous and there is quite big memory hole between the DDR/SDRAM regions). This patch reworks LBC SDRAM setup so that now we dynamically place the LBC SDRAM near the DDR (or at 0x0 if there isn't any DDR memory). With this patch we're able to: - Boot without external DDR memory; - Use most "DDR + SDRAM" setups without need to support for sparse/discontinuous memory model in the software. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-181-203/+203
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* mpc83xx: add h/w flash protection to board configsKim Phillips2008-09-241-0/+1
| | | | | | | | the operating system may leave flash in a h/w locked state after writing. This allows u-boot to continue to write flash by enabling h/w unlocking by default. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD2008-09-101-6/+6
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-101-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHEREJean-Christophe PLAGNIOL-VILLARD2008-09-101-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* drivers/mtd: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2008-08-131-1/+1
| | | | | | rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 83xx/85xx: further localbus cleanupsAnton Vorontsov2008-06-101-1/+1
| | | | | | | | | | | | | move the BRx_* and ORx_* left behind in mpc85xx.h The same is needed for mpc8xx.h and mpc8260.h (defines are almost the same, just few differences which needs some attention though). But the bad news for mpc8xx and mpc8260 is that there are a lot of users of these defines. So this cleanup I'll leave for the "better times". Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* PPC: Create and use CONFIG_HIGH_BATSBecky Bruce2008-06-031-0/+2
| | | | | | | | | | | Change all code that conditionally operates on high bat registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS instead of the myriad ways this is done now. Define the option for every config for which high bats are supported (and enabled by early boot, on parts where they're not always enabled) Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc83xx: bump loadaddr over fdtaddr to 0x500000Kim Phillips2008-04-251-1/+1
| | | | | | | | this seems as a good compromise between human memory, typing, and last but not least, to accommodate for current and future kernel bloat. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Dave Liu <daveliu@freescale.com>
* mpc83xx: Set PCI I/O bus-address base to zero.Scott Wood2008-03-251-1/+1
| | | | | | | | | | The device trees for these boards describe PCI I/O as starting from address zero from the device's perspective. Placing I/O elsewhere may cause problems with certain PCI boards, and may cause problems with Linux. Signed-off-by: Scott Wood <scottwood@freescale.com>
* Enable CONFIG_FLASH_SHOW_PROGRESS on the MPC8360EMDS.Jerry Van Baren2008-03-251-0/+1
| | | | | Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: make dtb basename file references equal those of linuxKim Phillips2008-03-071-1/+1
| | | | | | | the dts file basenames were updated in linux - this helps avoid inadvertently loading any old dtbs laying around. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Remove #undef DEBUG from MPC83xx board header filesTimur Tabi2008-02-121-2/+0
| | | | | | | | | Remove the "#undef DEBUG" line from all Freescale 83xx board header files. The inclusion of this line makes it impossible to enable debug code in other source files, because "#define DEBUG" typically needs to be defined before any header files are included. Signed-off-by: Timur Tabi <timur@freescale.com>
* mpc83xx: fix QE ETHPRIMEs to correct 'FSL UEC0' valueKim Phillips2008-01-161-1/+1
| | | | | | continuation of commit b96c83d4ae475a70ef2635cd0e748174c44c8601 Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Enable the isdram command on the MPC8360EMDS boardJerry Van Baren2008-01-161-0/+1
| | | | | | | | | The isdram command prints out decoded information the "serial presence detect" (SPD) chip on the SDRAM SIMMs. This can be very helpful when debugging memory configuration problems. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: Remove cache config from config.hDave Liu2008-01-101-9/+0
| | | | | | | clean up the cache config from configs.h of board Signed-off-by: Dave Liu <daveliu@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
OpenPOWER on IntegriCloud