summaryrefslogtreecommitdiffstats
path: root/include/configs/MPC8260ADS.h
Commit message (Collapse)AuthorAgeFilesLines
* Add board support for armadillo HT1070Wolfgang Denk2005-09-261-1/+1
| | | | Patch by Rowel Atienza, 06 Apr 2005
* Second Ethernet address enabled for MPC885ADS and MPC8272ADS.Wolfgang Denk2005-09-261-0/+4
| | | | Patch by Vitaly Bordug, 30 Mar 2005
* CleanupWolfgang Denk2005-09-251-9/+2
|
* Added support for PCI bridge on MPC8272ADSWolfgang Denk2005-09-251-3/+95
| | | | Patch by Vitaly Bordug, Feb 09 2005
* * Fix PHY address argument passing with mii info commandWolfgang Denk2005-09-241-10/+11
| | | | | | Patch by Andrew Dyer, 28 Dec 2004 * Cleanup: fix broken builds
* Add common (with Linux) MTD partition scheme and "mtdparts" commandWolfgang Denk2005-08-081-3/+7
| | | | | | | | Old, obsolete and duplicated code was cleaned up and replace by the new partitioning method. There are two possible approaches now: * define a single, static partition * use mtdparts command line option and dynamic partitioning Default is static partitioning.
* * Patch by Jon Loeliger, Kumar Gala 2005-02-08Jon Loeliger2005-07-231-0/+2
| | | | | | | | - Convert the CPM2 based functionality to use new CONFIG_CPM2 option rather than a myriad of CONFIG_MPC8560-like variants. Applies to MPC85xx and MPC8260 boards, includes stxgp3 and sbc8560. Eliminates the CONFIG_MPC8560 option entirely. Distributes the new CONFIG_CPM2 option to each 8260 board.
* Patch by Jerry Van Baren, 08 Nov 2004:wdenk2005-04-031-2/+21
| | | | | | | | - Add low-boot option for MPC8260ADS board (if lowboot is selected, the jumper for the HRCW source should select flash. If lowboot is not selected, the jumper for the HRCW source should select the BCSR. - change default load base address to 0x00400000
* Fix problems with SNTP support;wdenk2005-04-021-26/+27
| | | | enable SNTP support in some boards.
* * Code cleanup, mostly for GCC-3.3.xwdenk2004-12-311-0/+2
| | | | | | | | | | | | * Cleanup confusing use of CONFIG_ETH*ADDR - ust his only to pre-define a MAC address; use CONFIG_HAS_ETH* to enable support for additional ethernet addresses. * Cleanup drivers/i82365.c - avoid duplication of code * Fix bogus "cannot span across banks" flash error message * Add support for CompactFlash for the CPC45 Board.
* * Patch by Gridish Shlomi, 30 Aug 2004:wdenk2004-10-101-1/+1
| | | | | | | | | | | | | | | | | - Add support to revA version of PQ27 and PQ27E. - Reverted MPC8260ADS baudrate back to original 115200 * Patch by Hojin, 17 Sep 2004: Fix typo in cfi_flash.c * Patch by Mark Jonas, 09 September 2004: mtest's data line test (with CFG_ALT_MEMTEST set) returned a wrong error message * Patch by Mark Jonas, 31 August 2004: Added option CFG_XLB_PIPELINING to enable XLB pipelining. This improves FTP performance for MPC5200 systems. Enabled for IceCube by default.
* Patch by Robert Schwebel, 13 May 2004:wdenk2004-06-091-2/+3
| | | | Add 'imgextract' command: extract one part of a multi file image.
* * Patches by Pantelis Antoniou, 30 Mar 2004:wdenk2004-04-151-35/+64
| | | | | | | | | | - add auto-complete support to the U-Boot CLI - add support for NETTA and NETPHONE boards; fix NETVIA board * Patch by Yuli Barcohen, 28 Mar 2004: - Add support for MPC8272 family including MPC8247/8248/8271/8272 - Add support for MPC8272ADS evaluation board (another flavour of MPC8260ADS) - Change configuration method for MPC8260ADS family
* Code cleanupwdenk2004-03-251-0/+1
|
* * The PS/2 mux on the BMS2003 board needs 450 ms after power onwdenk2004-01-201-1/+1
| | | | | | | | | | | | before we can access it; add delay in case we are faster (with no CF card inserted) * Cleanup of some init functions * Make sure SCC Ethernet is always stopped by the time we boot Linux to avoid Linux crashes by early packets coming in. * Accelerate flash accesses on LWMON board by using buffered writes
* * Patch by Xue Ligong (Joe), 13 Nov 2003:wdenk2003-12-071-8/+15
| | | | | | | | | | add Realtek 8019 ethernet driver * Patch by Yuli Barcohen, 13 Nov 2003: MPC826xADS/PQ2FADS cleanup * Patch by Anders Larsen, 12 Nov 2003: Update README to mark the PORTIO commands non-standard
* Patch by Yuli Barcohen, 7 Aug 2003:wdenk2003-08-311-1/+8
| | | | | | | | | According to the MPC8260 User's Manual, PCI_MODE signal should be reflected in SCCR register, and local bus pins configuration is taken from HRCW and appears in SIUMCR. For some reason it does not work this way, so the only possibility to detect if the board is configured in PCI mode is to check the BCSR. This patch sets SCCR and SIUMCR according to the BCSR.
* * Patch by Martin Krause, 17 Jul 2003:wdenk2003-07-171-19/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | add delay to get I2C working with "imm" command and s3c24x0_i2c.c * Patch by Richard Woodruff, 17 July 03: - Fixed bug in OMAP1510 baud rate divisor settings. * Patch by Nye Liu, 16 July 2003: MPC860FADS fixes: - add MPC86xADS support (uses MPC86xADS.h) - add 866P/T core support (also MPC859T/MPC859DSL/MPC852T) o PLPRCR changes o BRG changes (EXTAL/XTAL restricted to 10MHz) o don't trust gclk() software measurement by default, depend on CONFIG_8xx_GCLK_FREQ - add DRAM SIMM not installed detection - use more "correct" SDRAM initialization sequence - allow different SDRAM sizes (8xxADS has 8M) - default DER is 0 - remove unused MAMR defines from FADS860T.h (all done in fads.c) - rename MAMR/MBMR defines to be more consistent. Should eventually be merged into MxMR to better reflect the PowerQUICC datasheet. * Patch by Yuli Barcohen, 16 Jul 2003: support new Motorola PQ2FADS-ZU evaluation board which replaced MPC8260ADS and MPC8266ADS
* * Patches by Yuli Barcohen, 13 Jul 2003:wdenk2003-07-141-0/+8
| | | | | | | | | | | | | | | | | | - Correct flash and JFFS2 support for MPC8260ADS - fix PVR values and clock generation for PowerQUICC II family (8270/8275/8280) * Patch by Bernhard Kuhn, 08 Jul 2003: - add support for M68K targets * Patch by Ken Chou, 3 Jul: - Fix PCI config table for A3000 - Fix iobase for natsemi.c (PCI_BASE_ADDRESS_0 is the IO base register for DP83815) * Allow to enable "slow" POST routines by key press on power-on * Fix temperature dependend switching of LCD backlight on LWMON * Tweak output format for LWMON
* * Patch by Yuli Barcohen, 23 Jun 2003:wdenk2003-06-231-2/+5
| | | | | | | Update for MPC8260ADS board * Patch by Murray Jensen, 23 Jun 2003: - cleanup of GCC 3.x compiler warnings
* * Patches by David Müller, 12 Jun 2003:wdenk2003-06-191-13/+28
| | | | | | | | | | | | | - rewrite of the S3C24X0 register definitions stuff - "driver" for the built-in S3C24X0 RTC * Patches by Yuli Barcohen, 12 Jun 2003: - Add MII support and Ethernet PHY initialization for MPC8260ADS board - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset configuration word supplied by FPGA on some MPC8260ADS boards * Patch by Pantelis Antoniou, 10 Jun 2003: Unify status LED interface
* * Fix CONFIG_NET_MULTI support in include/net.hwdenk2003-06-151-0/+1
| | | | | | | | | | | | | * Patches by Kyle Harris, 13 Mar 2003: - Add FAT partition support - Add command support for FAT - Add command support for MMC ---- - Add Intel PXA support for video - Add Intel PXA support for MMC ---- - Enable MMC and FAT for lubbock board - Other misc changes for lubbock board
* * Patch by Dave Ellis, 22 May 2003:wdenk2003-05-221-1/+1
| | | | | | | | Fix problem with only partially cleared .bss segment * Patch by Rune Torgersen, 12 May 2003: get PCI to work on a MPC8266ADS board; incorporate change to cpu/mpc8260/pci.c to enable overrides of PCI memory parameters
* Compile fixeswdenk2003-04-201-0/+1
|
* Make compile clean, fix the usual small problems.wdenk2003-03-261-0/+1
|
* * Patch by Rune Torgersen, 13 Feb 2003:wdenk2003-03-061-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Motorola MPC8266ADS board * Patch by Kyle Harris, 19 Feb 2003: patches for the Intel lubbock board: memsetup.S - general cleanup (based on Robert's csb226 code) flash.c - overhaul, actually works now lubbock.c - fix init funcs to return proper value * Patch by Kenneth Johansson, 26 Feb 2003: - Fixed off by one in RFTA calculation. - No need to abort when LDF is lower than we can program it's only minimum timing so clamp it to what we can do. - Takes function pointer to function for reading the spd_nvram. Usefull for faking data or hardcode a module without the nvram. - fix other user for above change - fix some comments. * Patches by Brian Waite, 26 Feb 2003: - fix port for evb64260 board - fix PCI for evb64260 board - fix PCI scan * Patch by Reinhard Meyer, 1 Mar 2003: Add support for EMK TOP860 Module * Patch by Yuli Barcohen, 02 Mar 2003: Add SPD EEPROM support for MPC8260ADS board
* * Patch by Daniel Engström, 13 Nov 2002:wdenk2002-11-181-0/+1
| | | | | | | Add support for i386 architecture and AMD SC520 board * Patch by Pierre Aubert, 12 Nov 2002: Add support for DOS filesystem and booting from DOS floppy disk
* * Patch by Jim Sandoz, 07 Nov 2002:wdenk2002-11-111-0/+1
| | | | | | | | | | Increase number of network RX buffers (PKTBUFSRX in "include/net.h") for EEPRO100 based boards (especially SP8240) which showed "Receiver is not ready" errors when U-Boot was processing the receive buffers slower than the network controller was filling them. * Get rid of obsolete include/mpc74xx.h
* Initial revisionwdenk2002-11-021-0/+267
OpenPOWER on IntegriCloud