| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
We should use the new address mapping functions unless we are in
compatibility mode. Disable the old functions by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
| |
|
|
|
|
|
|
| |
Move this function into the compatibility file so that it is not available
by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
| |
|
|
|
|
|
|
| |
Move these functions into the compatibility file so that they are not
available by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The address range check may overflow if the memory region is located at
the top of the 32-bit address space. This can e.g. be seen on TK1 if
using the E1000 gigabit Ethernet driver where start and size are both
0x80000000 leading to the following messages:
Apalis TK1 # tftpboot $loadaddr test_file
Using e1000#0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.2
Filename 'test_file'.
Load address: 0x80408000
Loading: pci_hose_phys_to_bus: invalid physical address
This patch fixes this by changing the order of the addition vs.
subtraction in the range check just like already done in
__pci_hose_bus_to_phys().
Reported-by: Ivan Mercier <ivan.mercier@nexvision.fr>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When converting between PCI bus and phys addresses, a two pass search
was introduced with preference to non-PCI_REGION_SYS_MEMORY regions.
See commit 2d43e873a29ca4959ba6a30fc7fb396d3fd0dccf.
However, since PCI_REGION_MEM is defined as 0, the if statement was
always asserted true: ((flags & PCI_REGION_MEM) == PCI_REGION_MEM)
This patch uses PCI_REGION_TYPE bit to check if the region is
PCI_REGION_MEM: ((flags & PCI_REGION_TYPE) == PCI_REGION_MEM)
Signed-off-by: Cheng Gu <chenggu@marvell.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit aec241d "dm: pci: Use the correct hose when configuring devices"
was an attempt to fix pci bridge device configuration, but unfortunately
that does not work 100%. In pciauto_config_devices(), the fix tried to
call pciauto_config_device() with a ctlr_hose which is supposed to be
the root controller hose, however when walking through a pci topology
with 2 or more pci bridges this logic simply fails.
The call chain is: pciauto_config_devices()->pciauto_config_device()
->dm_pci_hose_probe_bus(). Here the call to dm_pci_hose_probe_bus()
does not make any sense as the given hose is not the bridge device's
hose, instead it is either the root controller's hose (case#1: if it
is the 2nd pci bridge), or the bridge's parent bridge's hose (case#2:
if it is the 3rd pci bridge). In both cases the logic is wrong.
For example, for failing case#1 if the bridge device to config has the
same devfn as one of the devices under the root controller, the call
to pci_bus_find_devfn() will return the udevice of that pci device
under the root controller as the bus, but this is wrong as the udevice
is not a bus which does not contain all the necessary bits associated
with the udevice which causes further failures.
To correctly support pci bridge device configuration, we should still
call pciauto_config_device() with the pci bridge's hose directly.
In order to access valid pci region information, we need to refer to
the root controller simply by a call to pci_bus_to_hose(0) and get the
region information there in the pciauto_prescan_setup_bridge(),
pciauto_postscan_setup_bridge() and pciauto_config_device().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
Also add a comment to explain the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
| |
|
|
|
|
|
|
| |
pci_hose_phys_to_bus() is needed by several drivers. Move it to
pci_common.c to avoid a broken build when CONFIG_DM_PCI is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
|
Driver model will share many functions with the existing PCI implementation.
Move these into their own file to avoid duplication and confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
