summaryrefslogtreecommitdiffstats
path: root/drivers/net/phy/Makefile
Commit message (Collapse)AuthorAgeFilesLines
* phylib: add support for aquantia PHYsShaohui Xie2015-01-161-0/+1
| | | | | | | | This patch supports AQ1202, AQ2104, AQR105 PHY. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
* net/phy: Add support for CS4315/CS4340 PHYShengzhou Liu2014-12-051-0/+1
| | | | | | | | | | | | Add support for Cortina CS4315/CS4340 10G PHY. - This driver loads CS43xx firmware from NOR/NAND/SPI/SD device to initialize Cortina PHY. - Cortina PHY has non-standard offset of PHY ID registers, thus we define own get_phy_id() to override default get_phy_id(). - To define macro CONFIG_PHY_CORTINA will enable this driver. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* drivers: net: remove dead driversMasahiro Yamada2014-08-211-1/+0
| | | | | | | | | | The following configs are not defined at all: - CONFIG_INCA_IP_SWITCH - CONFIG_PBL2800_ETHER - CONFIG_PHY_ICPLUS Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* drivers: net: convert makefiles to Kbuild styleMasahiro Yamada2013-10-311-41/+19
| | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* net: add ICPlus PHY driverYegor Yefremov2013-06-241-0/+1
| | | | | | | The driver code was taken from Linux kernel source: drivers/net/phy/icplus.c Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
* phy: add support for ET1011C physMatt Porter2013-05-101-0/+1
| | | | | | | | | | | | Adds an ET1011C PHY driver which is derived from the Linux kernel PHY driver (drivers/net/phy/et1011c.c) from the v3.9-rc2 tag. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the PG1.0 TI814X EVM. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
* net/phy: support the mv88e6352 switchValentin Longchamp2012-09-271-0/+1
| | | | | | | | | | | | | | | | | This patch add support for the configuration of an external switch from the 88E6xxx series from Marvell trough an MDIO link using indirect adressing. This can be used if we do not want to use an EEPROM for the configuration. This driver is not generic and was not tested on other switches than the 88e6352. This is proposed as a first implementation that is somewhat limited but works and that can be used as a basis for further developments for this switch family. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Joe Hershberger <joe.hershberger@gmail.com>
* phy: Add support for SMSC LAN87xx PHYsNobuhiro Iwamatsu2011-12-051-0/+1
| | | | | | | | | | | | | | | This adds support for the SMSC LAN87xx PHYs. Following PHYs can be used by set CONFIG_PHY_SMSC to config. - SMSC LAN8700 - SMSC LAN8710/LAN8720 - SMSC LAN8710/LAN8720 A setup of PHY was copied from linux kenrel. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Fixed white space errors; modified commit message a bit. Signed-off-by: Wolfgang Denk <wd@denx.de>
* phylib: Add a bunch of PHY drivers from tsecAndy Fleming2011-04-201-0/+11
| | | | | | | | | | | | | | | | The tsec driver had a bunch of PHY drivers already written. This converts them all into PHY Lib drivers, and serves as the first set of PHY drivers for PHY Lib. While doing that, cleaned up a number of magic numbers (though not all of them, as PHY vendors like to keep their numbers as magical as possible). Also, noticed that almost all of the vitesse/cicada PHYs had the same config/parse/startup functions, so those have been collapsed into one. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
* Create PHY Lib for U-BootAndy Fleming2011-04-201-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extends the mii_dev structure to participate in a full-blown MDIO and PHY driver scheme. The mii_dev structure and miiphy calls are modified in such a way to allow the original mii command and miiphy infrastructure to work as before, but also to support a new set of APIs which allow (among other things) sharing of PHY driver code and 10G support The mii command will continue to support normal PHY management functions (Clause 22 of 802.3), but will not be changed to support 10G (Clause 45). The basic design is similar to PHY Lib from Linux, but simplified for U-Boot's network and driver infrastructure. We now have MDIO drivers and PHY drivers An MDIO driver provides: read write reset A PHY driver provides: (optionally): probe config - initial setup, starting of auto-negotiation startup - waiting for AN, and reading link state shutdown - any cleanup needed The ethernet drivers interact with the PHY Lib using these functions: phy_connect() phy_config() phy_startup() phy_shutdown() Each PHY driver can be configured separately, or all at once using config_phylib_all_drivers.h (added in the patch which adds the drivers) We also provide generic drivers for Clause 22 (10/100/1000), and Clause 45 (10G) PHYs. We also implement phy_reset(), and call it in phy_connect(). Because phy_reset() is essentially the same as miiphy_reset, but: a) must support 10G PHYs, and b) should use the phylib primitives, we implement miiphy_reset, using phy_reset(), but only when CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this way, we save on compile size, even if we don't manage to save code size. Pulled ethtool.h and mdio.h from: git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6 782d640afd15af7a1faf01cfe566ca4ac511319d With many, many deletions so as to enable compilation under u-boot Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* Marvell MV88E61XX Switch Driver supportPrafulla Wadaskar2009-06-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | Chips supported:- 1. 88E6161 6 port gbe swtich with 5 integrated PHYs 2. 88E6165 6 port gbe swtich with 5 integrated PHYs 2. 88E6132 3 port gbe swtich with 2 integrated PHYs Platform specific configuration supported for:- default or router port vlan configuration led_init configuration mdip/n polarity reversal configuration Note: This driver is supported and tested against kirkwood egiga interface Contributors: Yotam Admon <yotam@marvell.com> Michael Blostein <michaelbl@marvell.com Reviewed by: Ronen Shitrit <rshitrit@marvell.com> Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* miiphyutil: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2008-08-291-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* miiphybb: move to drivers/net/phyJean-Christophe PLAGNIOL-VILLARD2008-08-291-0/+46
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
OpenPOWER on IntegriCloud