summaryrefslogtreecommitdiffstats
path: root/board
Commit message (Collapse)AuthorAgeFilesLines
* arm: mx6: cm-fx6: print PCB revisionNikita Kiryanov2015-09-021-0/+7
| | | | | | | | | Print board revision for cm-fx6. Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* arm: mx6: cm-fx6: force host mode on usb controllerNikita Kiryanov2015-09-021-0/+6
| | | | | | | | | | | | | | | | | | On some CM-FX6 modules U-Boot attempts to configure the usb0 controller in device mode, which renders it unavailable: USB0: Port not available. and also causes usb stop to report an error EHCI failed to shut down host controller. This happens mostly on MX6 Dual based modules, and is caused by the USBPHY_CTRL register reporting USBPHY_CTRL_OTG_ID to be 1, even when it is pulled down. Since we do not support device mode in cm-fx6 u-boot, force all controllers to be configured as hosts. Cc: Stefano Babic <sbabic@denx.de> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* arm, imx6: add aristainetos 2b board versionHeiko Schocher2015-09-023-8/+65
| | | | | | | | | | | | there is a 2b board version of the aristainetos2 board. Differences to the v2: - spi cs for the nor flash and display controller changed - some pinmux changes - LED gpio settings changed Signed-off-by: Heiko Schocher <hs@denx.de>
* imx: mx6slevk: add SPL supportPeng Fan2015-09-021-0/+164
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add SPL boot support for mx6slevk board. 1. Introduce a configuration file mx6slevk_spl_defconfig. 2. i.MX6SL has same DRAM space with i.MX6SX, need to change SPL DRAM SPACE. 3. Include imx6_spl.h and related SPL macro in mx6slevk.h. 4. select SUPPORT_SPL for TARGET_MX6SLEVK. 5. Add SPL board code to do related initialization. Boot Log: U-Boot SPL 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59) reading u-boot.img reading u-boot.img U-Boot 2015.07-00544-g1594a76 (Aug 17 2015 - 01:56:59 +0000) CPU: Freescale i.MX6SL rev1.2 996 MHz (running at 396 MHz) CPU: Commercial temperature grade (0C to 95C) at 50C Reset cause: POR Board: MX6SLEVK I2C: ready DRAM: 1 GiB PMIC: PFUZE100 ID=0x10 MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
* imx: mx6: ddr init MMDC according to ddr_typePeng Fan2015-09-027-0/+7
| | | | | | | | | | | | | | | | | To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper. The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg when ddr_type is for DDR3. Later we can use ddr_type to initialize MMDC for LPDDR2. Initialize ddr_type for different boards which enable SPL. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Stefan Roese <sr@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Stefan Roese <sr@denx.de>
* tbs2910: remove SYS_SOC from board specific KconfigSoeren Moch2015-09-021-3/+0
| | | | | | | SYS_SOC is already defined in arch/arm/cpu/armv7/mx6/Kconfig, no need to define it again Signed-off-by: Soeren Moch <smoch@web.de>
* tbs2910: remove deprecated CONFIG_SYS_EXTRA_OPTIONSSoeren Moch2015-09-021-0/+6
| | | | | | move options from CONFIG_SYS_EXTRA_OPTIONS to board specific Kconfig Signed-off-by: Soeren Moch <smoch@web.de>
* arm, imx6: aristainetos board updatesHeiko Schocher2015-09-022-10/+6
| | | | | | | | | | some small updates for the aristainetos boards: - fix display timings for the aristainetos board - fix pinmux for the aristainetos board - fix pinmux for the aristainetos2 board - fix default environment Signed-off-by: Heiko Schocher <hs@denx.de>
* imx: mx6ul_14x14_evk add ENET supportPeng Fan2015-09-021-0/+110
| | | | | | | | | | | Add enet support for mx6ul_14x14_evk board: 1. add pinmux settings 2. implement board_eth_init 3. implement board_phy_config Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
* imx: clock support enet2 anatop clock supportPeng Fan2015-09-026-6/+6
| | | | | | | | | | | | | | | | To i.MX6SX/UL, two ethernet interfaces are supported. Add ENET2 clock support: 1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed. To value 1, only i.MX6SX/UL can pass the check. 2. Modify board code who use this api to follow new api prototype. Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Cc: Heiko Schocher <hs@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefan Roese <sr@denx.de> Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
* ARM: ts4800: add ethernet supportDamien Riegel2015-09-021-0/+103
| | | | | | | | | | This commit adds ethernet support to the TS4800. Note that the MAC address is not fused on this board and have to be read from FEC PALR PAUR registers (this is how the kernel provided by Technologic Systems does it). signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com> Cc: Stefano Babic <sbabic@denx.de>
* ARM: ts4800: add basic board supportLucile Quirion2015-09-025-0/+198
| | | | | | | | | | | | This commit adds basic support including: MMC, Serial console, TS4800 watchdog The config use CONFIG_SKIP_LOWLEVEL_INIT as U-boot is used as a second stage bootloader. Signed-off-by: Lucile Quirion <lucile.quirion@savoirfairelinux.com> signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com> Cc: Stefano Babic <sbabic@denx.de>
* nitrogen6x: change maintainerEric Nelson2015-09-021-1/+1
| | | | | | | Troy Kisky will be maintaining the Nitrogen6x board going forward. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
* cgtqmx6eval: Add Ethernet supportOtavio Salvador2015-09-021-0/+207
| | | | | | | | | cgtqmx6eval can be populated with a AR8035 or KSZ9031 depending on the board revision. Add Ethernet support. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* arm: mx6: Remove SPI support from WRU-IV baseboardStefan Roese2015-09-021-0/+1
| | | | | | | | | | | | This patch removes the SPI support from the WRU-IV baseboard as its not used at all. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Clemens Gruber <clemens.gruber@pqgruber.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de> Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* udoo: Switch to SPL supportvpeter42015-09-028-245/+328
| | | | | | | | | | | | | | | | | | | Currently we need to build one U-boot image for each of the udoo variants: quad and dual-lite. By switching to SPL we can support all two variants with a single binary. Based on the SPL for wandboard. Tested with OpenELEC (Open Embedded Linux Entertainment Center) on both boards. Signed-off-by: Peter Vicman <peter.vicman@gmail.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Peter Vicman <peter.vicman@gmail.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2015-08-313-11/+34
|\
| * sunxi: Fix MAINTAINERS board sortingHans de Goede2015-08-311-1/+1
| | | | | | | | | | | | | | | | The boards are sorted by SoC, move the Mele_A1000G_quad entry to the list of sun6i boards where it belongs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi: Add support for the Olimex A20 EVBMarcus Cooper2015-08-311-0/+5
| | | | | | | | | | | | Signed-off-by: Marcus Cooper <codekipper@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * sunxi: Add inet98v_rev2 defconfig and dts fileHans de Goede2015-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | The inet98v_rev2 is a pcb used in generic A13 based tablets. It features volume buttons, a power barrel, micro-usb otg, headphone connector and a power button. The dts file is identical to the one submitted to the upstream kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi: Add inet97fv2_defconfigHans de Goede2015-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | The inet97fv2 is a board found in the first generation of cheap allwinner A10 based 7" tablets. Note that this patch does not add a dts file as we already have one from our dts syncs with the kernel. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi_nand_spl: Rename SPL_NAND_SUNXI to NAND_SUNXIHans de Goede2015-08-311-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We eventually want to add full nand support, since it makes no sense to build SPL with nand support and u-boot without, or the other way around, a single option will suffice. Renaming the Kconfig option now makes things easier when we add full nand support in the future. The "obj-$(CONFIG_NAND_SUNXI) += sunxi_nand_spl.o" is moved to an "ifdef CONFIG_SPL_BUILD" block in the Makefile. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi_nand_spl: Add support for sun4i and sun5i SoCsHans de Goede2015-08-311-3/+9
| | | | | | | | | | | | | | | | | | | | | | | | Other then having a few less chip-select lines the nand controller on sun4i, sun5i and sun7i is identical. Note this patch also muxes GPC7 to the NAND on sun7i where as before it was not muxed this way. GPC7 is a standard NAND pin, so it should always be muxed to the NAND when in use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi_nand_spl: Make sure the DMA controller is enabledHans de Goede2015-08-311-0/+6
| | | | | | | | | | | | | | | | We use DMA for nand data transfers in the SPL, so make sure the DMA controller is enabled. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi_nand_spl: Use SYS_NAND_SELF_INIT and only do nand init when necessaryHans de Goede2015-08-311-5/+7
| | | | | | | | | | | | | | | | Use SYS_NAND_SELF_INIT and only setup the pinmux and clocks when we are actually using the nand. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi: Drop LCD_MODE from A13-OLinuxIno defconfigsHans de Goede2015-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With the unified / cleaned up default display output selection changes, which were done as part of adding composite video out support, our example LCD_MODE line in the A13-OLinuxIno defconfigs causes the display code to setup a LCD console by default, rather then a VGA console. Given that the LCD console is only useful for people who have hooked up the exact lcd-panel from the config, while most people will not have any lcd panel connected to these boards, this is not a good default. Dropping the LCD_MODE line which was intended as an example fixes this, instead add a link to the LCD_MODE help text pointing to http://linux-sunxi.org/LCD which contains the removed and other example modes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi: Add support for gt90h-v4 tabletsHans de Goede2015-08-311-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot. The pmic setup on this board is somewhat special, dcdc2 MUST be set to 1.1V instead of the usual 1.2V otherwise the board is very unstable. aldo1 is used to power the micro sd slot, dldo1 is used for wifi. This commit adds a defconfig + dts (as submitted to the kernel) for the gt90h-v4 pcb. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
| * sunxi: axp221: Allow specifying dcdc2 voltage via KconfigHans de Goede2015-08-311-1/+1
| | | | | | | | | | | | | | | | Allow specifying the axp221 dcdc2 voltage via Kconfig, this is necessary because on some boards the 1.2V default does not work reliable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | exynos: Rise ARM voltage to 1.1V for chained bootloadersMisha Komarovskiy2015-08-311-3/+4
|/ | | | | | | | | If board uses downstream Chrome OS U-Boot as first stage bootloader and upstream version is chained second stage, 1.1V is minimum voltage borderline. Signed-off-by: Misha Komarovskiy <zombah@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
* board: ti: invoke clock API to enable and disable clocksKishon Vijay Abraham I2015-08-284-0/+10
| | | | | | | | invoke enable_usb_clocks during board_usb_init and disable_usb_clocks during board_usb_exit to enable and disable clocks respectively. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: OMAP5: added USB initializtion codeKishon Vijay Abraham I2015-08-281-0/+75
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in omap5 board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: beagle_x15: added USB initializtion codeKishon Vijay Abraham I2015-08-281-0/+111
| | | | | | | | | Implemented board_usb_init(), board_usb_cleanup() and usb_gadget_handle_interrupts() in beagle_x15 board file that can be invoked by various gadget drivers. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board: ti: remove duplicate initialization of vbus_id_statusKishon Vijay Abraham I2015-08-282-4/+0
| | | | | | | | vbus_id_status is initialized in board_usb_init. So remove it while creating dwc3_device objects. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* at91sam9260ek: add missing files to MAINTAINERSAndreas Bießmann2015-08-281-0/+1
| | | | | | | | | | | This fixes the following genboardscfg.py warnings: ---8<--- WARNING: no status for 'at91sam9g20ek_2mmc' WARNING: no maintainers for 'at91sam9g20ek_2mmc' --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91sam9rlek: add missing files to MAINTAINERSAndreas Bießmann2015-08-281-0/+1
| | | | | | | | | | | This fixes following genboardscfg.py warning: ---8<--- WARNING: no status for 'at91sam9rlek_mmc' WARNING: no maintainers for 'at91sam9rlek_mmc' --->8--- Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm: spear: Fix booting - relocate vector table to 0 (low-vector)Stefan Roese2015-08-281-5/+0
| | | | | | | | | | | | Booting SPEAr600 eval board doesn't work with current mainline U-Boot. With this patch the low-vector bit is left to '0'. Resulting in the common relocation of the vectors to 0 (SDRAM) to work correctly. Tested on the SPEAr600 EVB. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com>
* ARM: k2l: Fix device speedsLokesh Vutla2015-08-281-1/+1
| | | | | | | | | | | ARM supported speeds and init value of core_pll for SDP1200 are programmed wrong as part for the device speed cleanups. Fixing it here. Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection") Tested-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Update READMELokesh Vutla2015-08-281-11/+15
| | | | | | | Update README to include uart boot mode support and makefile changes. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: keystone2: Rename u-boot-nand.gph to MLOLokesh Vutla2015-08-281-5/+5
| | | | | | | | | | | | | | NAND boot mode, ROM expects an image with a gp header in the beginning and an 8bytes filled with zeros at the end. The same is true for SD boot on K2G platforms but the file name should be MLO. Renaming u-boot-nand.gph to MLO, so that same image can be used for NAND and SD boots. And also not including all the u-boot only images under CONFIG_SPL_BUILD. Reported-by: Nishanth Menon <nm@ti.com> Reviewed-by: Nishanth Menon <nm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* ARM: DRA74-evm: Use SMA_1 spare register to workaround DP83865 phy on SR2.0Nishanth Menon2015-08-281-0/+3
| | | | | | | | | | | | | | | | | | | DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet provided IODELAY values for standard RGMII phys do not work. Silicon Revision(SR) 2.0 provides an alternative bit configuration that allows us to do a "gross adjustment" to launch the data off a different internal clock edge. Manual IO Delay overrides are still necessary to fine tune the clock-to-data delays. This is a necessary workaround for the quirky ethernet Phy we have on the platform. NOTE: SMA registers are spare "kitchen sink" registers that does contain bits for other workaround as necessary as well. Hence the control for the same is introduced in a generic SoC specific, board generic location. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: DRA74-evm: Add iodelay values for SR2.0Nishanth Menon2015-08-282-11/+83
| | | | | | | | | | | | | | | Silicon revision 2.0 has new signal routing hence has an updated set of iodelay parameters to be used. Update the configuration for the same. Padmux remains the same. Based on data from VayuES2_EVM_Base_Config-20150807. NOTE: With respect to the RGMII values, the Manual IODelay values are used for the fine adjusments needed to meet the tight RGMII specification. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* NDS32: Generic Board Support and UnsupportKun-Hua Huang2015-08-289-312/+0
| | | | | | Remove ag101 and ag102 support Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
* NDS32: Generic Board Support and UnsupportKun-Hua Huang2015-08-281-1/+0
| | | | | | Add nds32 ag101p generic board support. Signed-off-by: Kun-Hua Huang <kunhua@andestech.com>
* x86: crownbay: Enable on-board SMSC superio keyboard controllerBin Meng2015-08-261-3/+4
| | | | | | | | | | | | | | | So far we only enabled one legacy serial port on the SMSC LPC47m superio chipset on Intel Crown Bay board. As the board also has dual PS/2 ports routed out, enable the keyboard controller which is i8042 compatible so that we can use PS/2 keyboard and mouse. In order to make PS/2 keyboard work with the VGA console, remove CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode using PIRQ routing table, adjust the mask in the device tree to reserve irq12 which is used by PS/2 mouse. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Merge git://git.denx.de/u-boot-socfpgaTom Rini2015-08-2328-3205/+2749
|\ | | | | | | | | | | | | | | | | | | | | Conflicts: configs/socfpga_arria5_defconfig configs/socfpga_cyclone5_defconfig configs/socfpga_socrates_defconfig Merged these by hand and re-ran savedefconfig on them. Signed-off-by: Tom Rini <trini@konsulko.com>
| * arm: socfpga: Fix ArriaV SoCDK PLL configMarek Vasut2015-08-231-13/+13
| | | | | | | | | | | | | | | | Pull out the ArriaV SoCDK clock config from ancient Altera U-Boot "rel_socfpga_v2013.01.01_15.05.01_pr" and implant those values into mainline to get a booting ArriaV SoCDK. Signed-off-by: Marek Vasut <marex@denx.de>
| * arm: socfpga: Fix MAINTAINERS entry for CV/AV SoCDKMarek Vasut2015-08-232-9/+4
| | | | | | | | | | | | Repair the maintainer entries so they match the current state of code. Signed-off-by: Marek Vasut <marex@denx.de>
| * arm: socfpga: Make the pinmux table const u8Marek Vasut2015-08-232-2/+2
| | | | | | | | | | | | | | | | | | | | | | Now that we're actually converting the QTS-generated header files, we can even adjust their data types. A good candidate for this is the pinmux table, where each entry can have value in the range of 0..3, but each element is declared as unsigned long. By changing the type to u8, we can save over 600 Bytes from the SPL, so do it. This patch also constifies the array. Signed-off-by: Marek Vasut <marex@denx.de>
| * arm: socfpga: Switch to filtered QTS filesMarek Vasut2015-08-2320-2952/+2538
| | | | | | | | Signed-off-by: Marek Vasut <marex@denx.de>
| * arm: socfpga: Remove AV-specific parts from CV-SoCDKMarek Vasut2015-08-238-1153/+0
| | | | | | | | | | | | | | Just remove the ArriaV specific parts from the CycloneV SoCDK board and they are no longer needed now. Signed-off-by: Marek Vasut <marex@denx.de>
OpenPOWER on IntegriCloud