summaryrefslogtreecommitdiffstats
path: root/board
Commit message (Collapse)AuthorAgeFilesLines
* mx23_olinuxino: Do not set voltage selection bit for SSP padsFabio Estevam2013-05-061-1/+1
| | | | | | mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx23evk: Do not set voltage selection bit for SSP padsFabio Estevam2013-05-061-1/+1
| | | | | | mx23 SSP pad registers do not contain voltage selection bit, so just remove it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: m53evk: Convert to iomux-v3Benoît Thébaudeau2013-05-051-200/+120
| | | | | | | | | There is no change of behavior, except for the folloing line that has been removed because the iomux mode was not set accordingly and the pad used for OTG OC is not this one: mxc_iomux_set_input(MX53_USBOH3_IPP_IND_OTG_OC_SELECT_INPUT, 1); Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx53smd: Convert to iomux-v3Benoît Thébaudeau2013-05-051-104/+48
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx53loco: Convert to iomux-v3Benoît Thébaudeau2013-05-052-223/+113
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx53evk: Convert to iomux-v3Benoît Thébaudeau2013-05-051-206/+83
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx53ard: Convert to iomux-v3Benoît Thébaudeau2013-05-051-186/+141
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: ima3-mx53: Convert to iomux-v3Benoît Thébaudeau2013-05-051-155/+73
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: vision2: Convert to iomux-v3Benoît Thébaudeau2013-05-051-362/+223
| | | | | | | There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx51_efikamx/sb: Convert to iomux-v3Benoît Thébaudeau2013-05-051-53/+69
| | | | | | | | There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Matt Sealey <matt@genesi-usa.com>
* imx: mx51evk: Convert to iomux-v3Benoît Thébaudeau2013-05-052-239/+131
| | | | | | | There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: iomux-mx51: Fix MX51_PAD_EIM_CS2__GPIO2_27Benoît Thébaudeau2013-05-051-1/+1
| | | | | | | In ALT1 mode, EIM_CS2 is GPIO2[27], not ESDHC1.CD. Hence, rename MX51_PAD_EIM_CS2__SD1_CD to MX51_PAD_EIM_CS2__GPIO2_27. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: woodburn: Convert to iomux-v3Benoît Thébaudeau2013-05-051-32/+37
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx35pdk: Convert to iomux-v3Benoît Thébaudeau2013-05-051-99/+74
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx35pdk: Fix WDOG_RST iomux functionBenoît Thébaudeau2013-05-051-1/+1
| | | | | | | The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not ALT1 (which even corresponds to nothing). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: flea3: Convert to iomux-v3Benoît Thébaudeau2013-05-051-43/+48
| | | | | | There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: zmx25: Convert to iomux-v3Benoît Thébaudeau2013-05-051-71/+72
| | | | | | | There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: tx25: Convert to iomux-v3Benoît Thébaudeau2013-05-051-39/+68
| | | | | | | There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx25pdk: Fix GPIO assignmentsBenoît Thébaudeau2013-05-051-2/+2
| | | | Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: mx25pdk: Convert to iomux-v3Benoît Thébaudeau2013-05-051-53/+75
| | | | | | | There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* arm: mx5: Add support for DENX M53EVKMarek Vasut2013-05-053-0/+556
| | | | | | | | | | | | | | | | Add basic support for the DENX M53EVK board. Currently supported is: MMC (incl. booting) NAND (incl. booting) Ethernet, I2C, USB, SATA, RTC. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de>
* mx23_olinuxino: Fix DDR pin iomux settingsFabio Estevam2013-05-051-1/+1
| | | | | | | Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx23evk: Fix DDR pin iomux settingsFabio Estevam2013-05-051-1/+1
| | | | | | | Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: iomux-v3: Include PKE and PUE to pad control pull definitionsBenoît Thébaudeau2013-04-288-99/+73
| | | | | | | | | | | | | | | | | PUE requires PKE to mean something, as do pull values with PUE, so do not compell users to explicitly use PKE and PUE everywhere. This is also what is done on Linux and what has already been done for i.MX51. By the way, remove some unused pad control definitions. There is no change of behavior. Note that SPI_PAD_CTRL was defined by several boards with a pull value, but without PKE or PUE, which means that no pull was actually enabled in the pad. This might be a bug in those boards, but this patch does not change the behavior, so it just removes the meaningless pull value from those definitions. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* imx: Homogenize and fix fuse register definitionsBenoît Thébaudeau2013-04-281-1/+4
| | | | | | | | | | | | | | | | | | IIM: - Homogenize prg_p naming (the reference manuals are not always self-consistent for that). - Add missing SCSx and bank registers. - Fix the number of banks on i.MX53. OCOTP: - Rename iim to ocotp in order to avoid confusion. - Rename fuse_data to read_fuse_data, and sticky to sw_sticky, according to the reference manual. - Merge the existing spinoff gp1 fuse definition on i.MX6. - Fix the number of banks on i.MX6. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx53ard: Move register masks into imx-regs.hFabio Estevam2013-04-251-2/+0
| | | | | | | imx-regs.h is more appropriate location for containing register masks. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
* wandboard: Add boot selection supportOtavio Salvador2013-04-251-0/+19
| | | | | | | | Adds support for 'bmode' command which let user to choose where to boot from; this allows U-Boot to load system from another storage without messing with jumpers. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* wandboard: Add support for Carrier Board MicroSD cardOtavio Salvador2013-04-251-7/+52
| | | | | | | | Allow use of the carrier board MicroSD card available in the Wandboard; this allow for loading alternative system from the other card for testing or upgrade proposes. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* wandboard: Add card detection for SOM MicroSD cardOtavio Salvador2013-04-251-0/+18
| | | | | | | | This add support to identify if the card is connected or not; so it does not try to communicate with the controller if no card is available. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* mx6qsabresd: Return status when initializing MMCOtavio Salvador2013-04-251-6/+7
| | | | Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
* nitrogen6x: Setup CCM_CCOSR registerFabio Estevam2013-04-251-0/+11
| | | | | | | | | | | | CKO1 drives sgtl5000 codec clock on nitrogen boards and wandboard. Doing this setup in the bootloader will allow us to remove a lot of code in arch/arm/mach-imx/mach-imx6q.c from the mainline kernel. Also, according to Eric Nelson: "enabling the clock <in the bootloader> will remove squeal after an ungraceful reboot (watchdog) if hooked up to speakers." Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: mx6q_4x_mt41j128.cfg: Setup CCM_CCOSR registerFabio Estevam2013-04-251-0/+11
| | | | | | | | | | | | | Setup CCM_CCOSR register to provide a CKO1 clock frequency of 16.5 MHz. CKO1 drives sgtl5000 codec clock on mx6qsabrelite and doing this setup in the bootloader will allow us to remove a lot of code in arch/arm/mach-imx/mach-imx6q.c from the mainline kernel. mx6q_4x_mt41j128.cfg is also used by mx6qsabresd, and it is safe to use it for this board as well. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: Add titanium board support (i.MX6 based)Stefan Roese2013-04-223-0/+560
| | | | | | | | | | Titanium is a i.MX6 based board from ProjectionDesign / Barco. This patch adds support for this board with the newly introduced NAND support for i.MX6. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
* mx6sl: Add initial support for mx6slevk boardFabio Estevam2013-04-223-0/+248
| | | | | | | | | | mx6slevk board is a development board from Freescale based on the mx6 solo-lite processor. For details about mx6slevk, please refer to: http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=IMX6SLEVK&parentCode=i.MX6SL&fpsp=1 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* exynos: fdt: Add TMU node for snowSimon Glass2013-04-171-0/+14
| | | | | | | | Snow is missing a TMU node, and with TMU support this is not allowed, so it fails to boot. Add it. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos5: Add support for USB download boot modeVivek Gautam2013-04-171-2/+38
| | | | | | | | | | | | Exynos5250 supports secondary USB device boot mode. If the iROM fails to download u-boot from the primary boot device (such as SD or eMMC), it will try to retrieve from the secondary boot device (such as USB). Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Tegra: T30: Beaver board support.Tom Warren2013-04-151-0/+71
| | | | | | | | Beaver is a Tegra30 board that is nearly 100% compatible w/Cardhu. Add a Beaver build so it can begin to be differentiated, if need be. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: Split tegra_get_chip_type() into soc & sku funcsTom Warren2013-04-151-1/+1
| | | | | | | | | | | As suggested by Stephen Warren, use tegra_get_chip() to return the pure CHIPID for a Tegra SoC (i.e. 0x20 for Tegra20, 0x30 for Tegra30, etc.) and rename tegra_get_chip_type() to reflect its true function, i.e. tegra_get_chip_sku(), which returns an ID like TEGRA_SOC_T25, TEGRA_SOC_T33, etc. Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* Tegra: All Tamonten-derived boards use onboard NANDThierry Reding2013-04-152-11/+11
| | | | | | | | | Move the nand-controller node to the tegra20-tamonten.dtsi so that it can be shared between all derived boards. Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* smdk5250, snow: convert to CONFIG_SPL_MAX_FOOTPRINTAlbert ARIBAUD2013-04-141-1/+1
| | | | | | | | This target wants to check full SPL size, BSS included. Remove CONFIG_SPL_MAX_SIZE definition and instead define CONFIG_SPL_MAX_FOOTPRINT. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* da850evm, da850_am18xxevm: convert to CONFIG_SPL_MAX_FOOTPRINTAlbert ARIBAUD2013-04-141-1/+1
| | | | | | | | This target wants to check full SPL size, BSS included. Remove CONFIG_SPL_MAX_SIZE definition and instead define CONFIG_SPL_MAX_FOOTPRINT. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* cam_enc_4xx: convert to CONFIG_SPL_MAX_FOOTPRINTAlbert ARIBAUD2013-04-141-1/+1
| | | | | | | | This target wants to check full SPL size, BSS included. Remove CONFIG_SPL_MAX_SIZE definition and instead define CONFIG_SPL_MAX_FOOTPRINT. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* ARM: Fix __bss_start and __bss_end in linker scriptsAlbert ARIBAUD2013-04-135-20/+50
| | | | | | | | | | | | | | Commit 3ebd1cbc introduced compiler-generated __bss_start and __bss_end__ and commit c23561e7 rewrote all __bss_end__ as __bss_end. Their merge caused silent and harmless but potentially bug-inducing clashes between compiler- and linker- generated __bss_end symbols. Make __bss_end and __bss_start compiler-only, and create __bss_base and __bss_limit for linker-only use. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reported-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-1270-200/+104
|\ | | | | | | | | Conflicts: drivers/video/exynos_fb.c
| * nand: Extend nand_(read|write)_skip_bad with *actual and limit parametersTom Rini2013-04-101-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We make these two functions take a size_t pointer to how much space was used on NAND to read or write the buffer (when reads/writes happen) so that bad blocks can be accounted for. We also make them take an loff_t limit on how much data can be read or written. This means that we can now catch the case of when writing to a partition would exceed the partition size due to bad blocks. To do this we also need to make check_skip_len count not just complete blocks used but partial ones as well. All callers of nand_(read|write)_skip_bad are adjusted to call these with the most sensible limits available. The changes were started by Pantelis and finished by Tom. Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
| * replace last __bss_end__ occurrences with __bss_endAlbert ARIBAUD2013-04-0235-35/+35
| | | | | | | | | | | | | | | | | | | | Simon Glass' commit 3929fb0a141530551b3fce15ee08629f80d5ef2a, which changed all occurrences of __bss__end__ into __bss_end, left behind some untouched __bss_end__ occurrences in all 33 u-boot.lds.debug files, in board/mousse/u-boot.lds.ram and in board/mousse/u-boot.lds.rom. These are replaced here. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
| * Consolidate bool typeYork Sun2013-04-0131-134/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | 'bool' is defined in random places. This patch consolidates them into a single header file include/linux/types.h, using stdbool.h introduced in C99. All other #define, typedef and enum are removed. They are all consistent with true = 1, false = 0. Replace FALSE, False with false. Replace TRUE, True with true. Skip *.py, *.php, lib/* files. Signed-off-by: York Sun <yorksun@freescale.com>
| * Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini2013-03-311-1/+2
| |\
| | * menu: Add support for user defined item choice functionPali Rohár2013-03-291-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Selecting menu items is currently done in menu_interactive_choice() by reading the user input strings from standard input. Extend menu_interactive_choice() to support user defined function for selecting menu items. This function and its argument can be specified when creating the menu. Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
| * | Merge branch 'for-v2013.04'Anatolij Gustschin2013-03-292-30/+2
| |\ \ | | |/ | |/| | | | | | | | | | | | | Conflicts: drivers/video/Makefile Signed-off-by: Anatolij Gustschin <agust@denx.de>
OpenPOWER on IntegriCloud