summaryrefslogtreecommitdiffstats
path: root/board/ti/am335x
Commit message (Collapse)AuthorAgeFilesLines
* board/ti/am335x: add support for BeagleBone Greenrobertcnelson@gmail.com2015-11-181-3/+9
| | | | | | | | | | | | | | | | | | | | | SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus the HDMI port and addition of two Grove connectors (i2c2 and usart2). This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom: 1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|] http://beagleboard.org/green http://www.seeedstudio.com/wiki/Beaglebone_green In Mainline Kernel as of: https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6 Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model) Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* board/ti/am335x: beaglebone stop muxing i2c1_pin_muxrobertcnelson@gmail.com2015-11-121-2/+0
| | | | | | | | | | | On the BeagleBone these i2c1 pins are routed to the expanasion header, where they can be defined as either pr1_usart0_Xxd/pwm0/spi0/i2c1, dont assume i2c1 Fixes: https://e2e.ti.com/support/arm/sitara_arm/f/791/p/313894/1387696 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com> CC: Tom Rini <trini@konsulko.com>
* board/ti: Update MAINTAINERS entries with more boardsTom Rini2015-11-101-0/+1
| | | | | | | A few config files have been added without updating MAINTAINERS. Reported-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: AM335x: mux: change mmc0 cd pinmux from mmc0_sdcd to gpioMugunthan V N2015-10-221-1/+1
| | | | | | | | | | Currently omap_hsmmc driver doesn't use sdcd pin to detect whether the card is present or not. Instead the same pin is used as GPIO to detect card presence. So change the pin mux mode from mmc0_sdcd to gpio0_6. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* am335x_evm: prepare for eth driver model supportMugunthan V N2015-10-221-0/+7
| | | | | | | | Prepare board file so that ethernet registration are commented for DM conversion Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSBPaul Kocialkowski2015-08-051-1/+1
| | | | | | | | | USB-related options are usually prefixed with CONFIG_USB and platform-specific adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* net: cosmetic: Name ethaddr variables consistentlyJoe Hershberger2015-04-181-3/+3
| | | | | | | | Use "_ethaddr" at the end of variables and drop CamelCase. Make constant values actually 'const'. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
* dm: select CONFIG_DM* optionsMasahiro Yamada2015-04-181-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As mentioned in the previous commit, adding default values in each Kconfig causes problems because it does not co-exist with the "depends on" syntax. (Please note this is not a bug of Kconfig.) We should not do so unless we have a special reason. Actually, for CONFIG_DM*, we have no good reason to do so. Generally, CONFIG_DM is not a user-configurable option. Once we convert a driver into Driver Model, the board only works with Driver Model, i.e. CONFIG_DM must be always enabled for that board. So, using "select DM" is more suitable rather than allowing users to modify it. Another good thing is, Kconfig warns unmet dependencies for "select" syntax, so we easily notice bugs. Actually, CONFIG_DM and other related options have been added without consistency: some into arch/*/Kconfig, some into board/*/Kconfig, and some into configs/*_defconfig. This commit prefers "select" and cleans up the following issues. [1] Never use "CONFIG_DM=n" in defconfig files It is really rare to add "CONFIG_FOO=n" to disable CONFIG options. It is more common to use "# CONFIG_FOO is not set". But here, we do not even have to do it. Less than half of OMAP3 boards have been converted to Driver Model. Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is weird. Instead, add "select DM" only to appropriate boards, which eventually eliminates "CONFIG_DM=n", etc. [2] Delete redundant CONFIGs Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again in configs/sandbox_defconfig. Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and defines it also in omap3_beagle_defconfig and devkit8000_defconfig. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* malloc_f: enable SYS_MALLOC_F by default if DM is onMasahiro Yamada2015-03-281-3/+0
| | | | | | | | | | | | | | This option has a bool type, not hex. Fix it and enable it if CONFIG_DM is on because Driver Model always requires malloc memory. Devices are scanned twice, before/after relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc memory before relocation. As it is board-independent, handle it globally. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Robert Baldyga <r.baldyga@samsung.com>
* malloc_f: remove redundant defalut values of CONFIG_SYS_MALLOC_F_LENMasahiro Yamada2015-03-281-3/+0
| | | | | | | | | | The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig as 0x400. Each defconfig or Kconfig need not repeat the same value. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Robert Baldyga <r.baldyga@samsung.com>
* MAINTAINERS, git-mailrc: Update my email addressTom Rini2015-03-021-6/+1
| | | | Signed-off-by: Tom Rini <trini@konsulko.com>
* kconfig: remove unneeded dependency on !SPL_BUILDMasahiro Yamada2015-02-241-5/+5
| | | | | | | Now CONFIG_SPL_BUILD is not defined in Kconfig, so "!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to KconfigSimon Glass2015-02-121-0/+6
| | | | | Move this option to Kconfig and update all boards. Signed-off-by: Simon Glass <sjg@chromium.org>
* dm: omap3: Move driver model CONFIGs to KconfigSimon Glass2015-02-121-0/+10
| | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
* doc: fix spelling errors in am335x/READMEJeremiah Mahler2015-01-081-3/+3
| | | | | | | Fix several spelling errors and replace the invalid word "architectured" with "designed". Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
* am335x_evm: Convert NOR_BOOT to KconfigTom Rini2014-11-051-0/+8
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* am335x_evm: Add NOR to KconfigTom Rini2014-11-051-0/+7
| | | | | | | Make enabling support for NOR (and describe where it's seen) be done via Kconfig. Signed-off-by: Tom Rini <trini@ti.com>
* kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-291-3/+0
| | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* am335x_boneblack: Only modify NAND/NOR/MMC1 pinmux on BBB in boneblack builds.Tom Rini2014-10-231-2/+2
| | | | | | | | | | In the case of Beaglebone Black we only want to set the NAND or NOR cape pinmux when the config has been specifically modified by the user for this non-default case. Make the default be to set the MMC1 (eMMC) pinmux. We don't need similar changes for Beaglebone White as there is nothing on MMC1 by default there. Signed-off-by: Tom Rini <trini@ti.com>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-131-5/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* arm: am335x: add Kconfig range attribute to prevent invalid CONS_INDEXMasahiro Yamada2014-09-041-0/+1
| | | | | | | | The help message in board/ti/am335x/Kconfig says AM335x has 6 UARTs, so the valid number for CONFIG_CONS_INDEX is from 1 to 6. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
* am335x_evm: Convert CONFIG_CONS_INDEX into a menu choiceTom Rini2014-08-253-18/+17
| | | | | | | | | | - Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead - Add choice and help text to board/ti/am335x/Kconfig - Correct comment about IDK in board/ti/am335x/mux.c - Remove am335x_evm_uart* defconfig files as they're just variations on a config option now. Signed-off-by: Tom Rini <trini@ti.com>
* board/ti/am335x: add support for beaglebone NOR Capepekon gupta2014-08-251-60/+35
| | | | | | | | | | | | | This patch adds support of NOR cape[1] for both Beaglebone (white) and Beaglebone(Black) boards. NOR Flash on this cape is connected to GPMC chip-select[0] and accesses as external memory-mapped device. This cape has 128Mbits(16MBytes), x16, CFI compatible NOR Flash device. As GPMC chip-select[0] can be shared by multiple capes so NOR profile is not enabled by default in boards.cfg. Following changes are required to enable NOR cape detection when building am335x_boneblack board profile. Signed-off-by: Tom Rini <trini@ti.com>
* board/ti/am335x: add support for beaglebone NAND capepekon gupta2014-08-251-20/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beaglebone Board can be connected to expansion boards to add devices to them. These expansion boards are called 'capes'. This patch adds support for following versions of Beaglebone(AM335x) NAND capes (a) NAND Device with bus-width=16, block-size=128k, page-size=2k, oob-size=64 (b) NAND Device with bus-width=16, block-size=256k, page-size=4k, oob-size=224 Further information and datasheets can be found at [1] and [2] * How to boot from NAND using Memory Expander + NAND Cape ? * - Important: As BOOTSEL values are sampled only at POR, so after changing any setting on SW2 (DIP switch), disconnect and reconnect all board power supply (including mini-USB console port) to POR the beaglebone. - Selection of ECC scheme for NAND cape(a), ROM code expects BCH8_HW ecc-scheme for NAND cape(b), ROM code expects BCH16_HW ecc-scheme - Selction of boot modes can be controlled via DIP switch(SW2) present on Memory Expander cape. SW2[SWITCH_BOOT] == OFF follow default boot order MMC-> SPI -> UART -> USB SW2[SWITCH_BOOT] == ON boot mode selected via DIP switch(SW2) So to flash NAND, first boot via MMC or other sources and then switch to SW2[SWITCH_BOOT]=ON to boot from NAND Cape. - For NAND boot following switch settings need to be followed SW2[ 1] = OFF (SYSBOOT[ 0]==1: NAND boot mode selected ) SW2[ 2] = OFF (SYSBOOT[ 1]==1: -- do -- ) SW2[ 3] = ON (SYSBOOT[ 2]==0: -- do -- ) SW2[ 4] = ON (SYSBOOT[ 3]==0: -- do -- ) SW2[ 5] = OFF (SYSBOOT[ 4]==1: -- do -- ) SW2[ 6] = OFF (SYSBOOT[ 8]==1: 0:x8 device, 1:x16 device ) SW2[ 7] = ON (SYSBOOT[ 9]==0: ECC done by ROM ) SW2[ 8] = ON (SYSBOOT[10]==0: Non Muxed device ) SW2[ 9] = ON (SYSBOOT[11]==0: -- do -- ) [1] http://beagleboardtoys.info/index.php?title=BeagleBone_Memory_Expansion [2] http://beagleboardtoys.info/index.php?title=BeagleBone_4Gb_16-Bit_NAND_Module *IMPORTANT NOTE* As Beaglebone board shares the same config as AM335x EVM, so following changes are required in addition to this patch for Beaglebone NAND cape. (1) Enable NAND in am335x_beaglebone board profile (2) Add CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config because: - AM335x EVM has NAND device with datawidth=8, whereas - Beaglebone NAND cape has NAND device with data-width=16
* Add board MAINTAINERS filesMasahiro Yamada2014-07-301-0/+17
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-301-0/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* am335x_evm / gumstix pepper: Correct DDR settingsTom Rini2014-07-251-27/+3
| | | | | | | | | | | | | | As noted by clang, we have been shifting certain values out of 32bit range when setting some DDR registers. Upon further inspection these had been touching reserved fields (and having no impact). These came in from historical bring-up code and can be discarded. Similarly, we had been declaring some fields as 0 when they will be initialized that way. Tested on Beaglebone White. Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Ash Charles <ash@gumstix.com> Signed-off-by: Tom Rini <trini@ti.com> Tested-By: Ash Charles <ashcharles@gmail.com>
* ti: am335x: Fix the U-Boot binary outputSimon Glass2014-06-111-1/+2
| | | | | | | This should include the hash so that image_binary_size is really at the end of the image, and not some 300 bytes earlier. Signed-off-by: Simon Glass <sjg@chromium.org>
* arm: move exception handling out of start.S filesAlbert ARIBAUD2014-05-151-0/+1
| | | | | | | | Exception handling is basically identical for all ARM targets. Factorize it out of the various start.S files and into a single vectors.S file, and adjust linker scripts accordingly. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOTTom Rini2014-04-172-2/+2
| | | | | | | | | | In the case of SPL or NOR_BOOT (no SPL involved) we need to include certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to make supporting XIP QSPI boot clearer in the code. Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Wolfgang Denk <wd@denx.de>
* am335x_evm: Make SPL_OS also check the boot_os variable for falcon modeTom Rini2014-04-171-1/+12
| | | | | | | | | We use the same variable as a3m071 in the environment to determine if we should boot into Linux or U-Boot. This is useful on boards like Beaglebone Black or AM335x GP EVM where we have persistent storage for the environment. Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2014-04-081-2/+16
|\ | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile include/configs/trats.h include/configs/trats2.h include/mmc.h
| * am335x_evm: Clarify when we build board_eth_initTom Rini2014-03-281-2/+16
| | | | | | | | | | | | | | | | If we build this function in cases where we would be discarding it anyhow we still end up with maybe unused warnings. Rather than litter the function with __maybe_unused, just spell out when to build it. Signed-off-by: Tom Rini <trini@ti.com>
* | arm: Handle .gnu.hash section in ldscriptsAndreas Färber2014-04-071-0/+1
|/ | | | | | | | | | Avoids "could not find output section .gnu.hash" ld.bfd errors on openSUSE. Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2014-03-101-2/+17
|\
| * ARM: AM335x: add support for reading cpsw 2nd mac address from efuseMugunthan V N2014-03-041-0/+15
| | | | | | | | | | | | | | | | | | Adding support for reading cpsw 2nd mac address from efuse and pass it to kernel via dtb which will be used in dual emac mode of cpsw. Also adding mii command support to am335x common config. Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
| * drivers: net: cpsw: add support to have phy address from cpsw platform dataMugunthan V N2014-03-041-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | Some platforms like AM437x have different EVMs with different phy addresses, so this patch adds support for passing phy address via cpsw plaform data. Also renamed phy_id to phy_addr so better understanding of the code. Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> [trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335 pengwyn boards] Signed-off-by: Tom Rini <trini@ti.com>
* | board/ti/am335x/README: update for NAND bootpekon gupta2014-03-031-17/+36
|/ | | | | | | | | NAND boot mode on AM335x EVM has been verified, and steps to use it has been documented and update in this README Signed-off-by: Pekon Gupta <pekon@ti.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Acked-by: Tom Rini <trini@ti.com>
* arm: make _end compiler-generatedAlbert ARIBAUD2014-02-261-2/+7
| | | | | | | | | This prevents references to _end from generating absolute relocation records. This change is binary invariant for ARM targets. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* ARM: AM33xx+: Update ioregs to pass different valuesLokesh Vutla2013-12-181-4/+36
| | | | | | | | | | | Currently same value is programmed for all ioregs. This is not the case for all SoC's like AM4372. So adding a structure for ioregs and updating in all board files. And also return from config_cmd_ctrl() and config_ddr_data() functions if data is not passed. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [trini: Fixup dxr2, cm_t335, adapt pcm051 rev3] Signed-off-by: Tom Rini <trini@ti.com>
* Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-12-102-15/+3
|\ | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/armv7/rmobile/Makefile doc/README.scrapyard Needed manual fix: arch/arm/cpu/armv7/omap-common/Makefile board/compulab/cm_t335/u-boot.lds
| * Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini2013-11-251-13/+1
| |\
| | * am335x: fix GPMC config for NAND and NOR SPL bootpekon gupta2013-11-211-13/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GPMC controller is common IP to interface with both NAND and NOR flash devices. Also, it supports max 8 chip-selects, which can be independently connected to any of the devices. But ROM code expects the boot-device to be connected to only chip-select[0]. Thus to resolve conflict between NOR and NAND boot. This patch: - combines NOR and NAND configs spread in board files to common gpmc_init() - configures GPMC based on boot-mode selected for SPL boot. Signed-off-by: Pekon Gupta <pekon@ti.com>
| * | Makefile: rename all libraries to built-in.oMasahiro Yamada2013-11-171-1/+1
| | | | | | | | | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
| * | i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher2013-11-131-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
* | arm: keep all sections in ELF fileAlbert ARIBAUD2013-12-071-6/+9
| | | | | | | | | | | | | | | | | | | | Current LDS files /DISCARD/ a lot of sections when linking ELF files, causing diagnostic tools such as readelf or objdump to produce partial output. Keep all section at link stage, filter only at objcopy time so that .bin remains minimal. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* | am33xx: Stop modifying certain EMIF4D registersTom Rini2013-12-041-17/+0
|/ | | | | | | | | | | | | | | Based on the definitive guide to EMIF configuration[1] certain registers that we have been modifying (and are documented registers) should be left in their reset values rather than modified. This has been tested on AM335x GP EVM and Beaglebone White. [1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Javier Martinez Canillas <javier@dowhile0.org> Cc: Heiko Schocher <hs@denx.de> Cc: Lars Poeschel <poeschel@lemonage.de> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Matt Porter <matt.porter@linaro.org>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-091-0/+6
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * am335x: Enable CONFIG_OMAP_WATCHDOG supportTom Rini2013-11-011-0/+6
| | | | | | | | | | | | | | There is a board-specific portion for calling watchdog enable itself, in main U-Boot. Signed-off-by: Tom Rini <trini@ti.com>
* | board: ti: convert makefiles to Kbuild styleMasahiro Yamada2013-10-311-27/+2
|/ | | | | Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
OpenPOWER on IntegriCloud