summaryrefslogtreecommitdiffstats
path: root/board/sunxi
Commit message (Collapse)AuthorAgeFilesLines
...
* sun6i: Make dram clk and zq value Kconfig optionsHans de Goede2015-01-141-0/+17
| | | | | | | | | | | | It turns out that there is a too large spread between boards to handle this with a default value, turn this into Kconfig options, and set the values the factory images are using for the Colombus and Mele_M9 boards. Note this changes the ZQ default when not overriden through defconfig from 120 to 123, as that is what most boards seem to actually use. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: remove redudant information from Kconfig filesMasahiro Yamada2015-01-121-1/+0
| | | | | | | | | - "string" type for SYS_* is defined in arch/Kconfig - SYS_CPU "armv7" has been replaced with "select CPU_V7" - SYS_SOC "tegra124" is already defined in tegra124/Kconfig Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Bo Shen <voice.shen@atmel.com>
* sun7i: Set ARMV7_BOOT_SEC_DEFAULT when OLD_SUNXI_KERNEL_COMPAT is setHans de Goede2014-11-251-0/+1
| | | | | | | | | | | Old kernels cannot handle booting in non-secure (hyp) mode, so when OLD_SUNXI_KERNEL_COMPAT is set, also set ARMV7_BOOT_SEC_DEFAULT. Note that whether to booting secure or non-secure can always be overriden using the bootm_boot_mode environment variable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Add gmac support for sun6i boardsHans de Goede2014-11-251-0/+45
| | | | | | | Hookup the gmac found on the sun6i / A31 SoCs. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: ahci: Add a delay after enabling target powerHans de Goede2014-11-251-0/+2
| | | | | | | | | | | | | | If the target power is connected through a gpio, then give the target some time to power up before continuing with ahci / sata probing, this avoids link timeouts, without penalizing other boards where there is no target power gpio. Why 500 ms ? I started with 200, that was not enough, then I went to 500 which worked, lowering it to 350 broke things again, so 500 seems the minimum my vertex2 needs to be ready to get probed. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add usb keyboard Kconfig optionHans de Goede2014-11-251-0/+7
| | | | | | | For use together with the hdmi console. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ian.campbell@citrix.com>
* sunxi: video: Add simplefb supportLuc Verhaegen2014-11-251-0/+10
| | | | | | | | | | | | Add simplefb support, note this depends on the kernel having support for the clocks property which has recently been added to the simplefb devicetree binding. Signed-off-by: Luc Verhaegen <libv@skynet.be> [hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as disussed on the devicetree list] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>.
* sunxi: video: Add cfb console driver for sunxiLuc Verhaegen2014-11-251-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | This adds a fixed mode hdmi driver for the sunxi platform. The fixed mode is a relatively safe 1024x768, more complete EDID handling is currently not provided. Only HDMI is supported today. This code is enabled when HPD detects an attached monitor. Current config is such that 8MB is shaved off at the top of the RAM. This avoids several memory handling issues, most significant is the fact that on linux on ARM you are not allowed to remap known RAM as IO. A clued in display driver will be able to recycle this reserved RAM in future though. cfbconsole was chosen as it provides the most important functionality: a working u-boot console, allowing for the debugging of certain issues without the need for a UART. Signed-off-by: Luc Verhaegen <libv@skynet.be> [hdegoede@redhat.com: Major cleanups and some small bugfixes] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Anatolij Gustschin <agust@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: Add arch/arm/cpu/armv7/Kconfig with non-secure and virt optionsHans de Goede2014-11-241-0/+2
| | | | | | | | | Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a preparation patch for adding an env variable to choose between secure / non-secure boot on non-secure boot capable systems, specifically this prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: gmac: Update bananapi fixup to the new CONFIG_TARGET_<BOARD> structureZoltan HERPAI2014-11-131-1/+1
| | | | | | | | The magic bit toucher needs to be updated to reflect the new board Kconfig structure Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sun6i: ehci: Add sun6i ehci supportHans de Goede2014-11-131-0/+2
| | | | | | | | Add support for the 2 ehci controllers found on the sun6i (A31) soc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Marek Vasut <marex@denx.de>
* sunxi: ehci: Add proper Kconfig options to select the usb Vbus gpio-sHans de Goede2014-11-131-0/+14
| | | | | | | | | Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to Kconfig being the right thing to do, an added advantage of this is that it allows for boards without Vbus gpio-s. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Add Mele M9 boardHans de Goede2014-11-132-0/+5
| | | | | Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Enable SPLHans de Goede2014-11-131-0/+1
| | | | | | | Enable the SPL now that we've all the necessary bits in place. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun6i: Add basic axp221 driverOliver Schinagl2014-11-131-0/+26
| | | | | | | | | | | | | | | | | | The A31 uses the AXP221 pmic for various voltages. Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> -- Changes in v2: -Rebase Changes in v3: -Add support for all dldo and aldo-s -Add Kconfig option to select building AXP221 and to select voltage of dldo and aldo-s Changes in v4: -Add axp221_setbits helper function -Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
* dm: sunxi: Make sure that GPIOs are requestedSimon Glass2014-11-051-0/+1
| | | | | | | | | | The scsi_init() function uses a GPIO so should request it. There is no way to return an error here, and the request may be made multiple times, so just ignore errors for now. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* dm: sunxi: Add a new config for an FDT-based pcDuino3Simon Glass2014-11-051-0/+1
| | | | | | | | | For now we won't want to mess with the existing configurations. Create a new one which will enable device tree and driver model. Note that this brings the device tree binary into u-boot-sunxi-with-spl.bin. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: kconfig: Introduce CONFIG_TARGET_<BOARD>Ian Campbell2014-11-052-22/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This was done automatically with the following bits of scripting. The Kconfig choice content was generated with this script snippet: for i in $(git grep -l CONFIG_ARCH_SUNXI configs/*) ; do TARGET=$(sed -n -e 's/CONFIG_SYS_EXTRA_OPTIONS="\([^,"]\+\).*/\1/p' $i); MACH=$(sed -n -e 's/.*CONFIG_\(MACH_SUN.I\)=./\1/p' $i) echo "config TARGET_$TARGET" echo " bool \"$TARGET\"" echo " depends on $MACH" echo done defconfigs were updated with a sed script (t): # Extract board from first entry of CONFIG_SYS_EXTRA_OPTIONS, /^CONFIG_SYS_EXTRA_OPTIONS/ { s/^\(CONFIG_SYS_EXTRA_OPTIONS="\)\([^,"]\+\),\?\(.*\)/\1\3\nCONFIG_TARGET_\2=y/; # Print and delete first line (CONFIG_SYS_EXTRA_OPTIONS), leaving # CONFIG_TARGET_<BOARD> in pattern space P;D; }; # Move CONFIG_TARGET_<BOARD> to hold space /^CONFIG_TARGET/{h;n} # Print CONFIG_TARGET_<BOARD> after CONFIG_MACH_<SOC> in either SPL or # normal mode. /^CONFIG_MACH/{p;g;p;n}; /^\+S:CONFIG_MACH/{p;g;s/^CONFIG_TARGET/+S:&/;p;n}; # Print any remaining lines normally p; Run as: sed -i -n -f t $(git grep -l CONFIG_ARCH_SUNXI configs/*) and then manually removing the one instance of CONFIG_SYS_EXTRA_OPTIONS="" from Colombus_defconfig board/sunxi/Makefile was updated with: sed -e 's/^\(obj-\$(CONFIG_\)\(.*\)\().*+= dram_.*\)/\1TARGET_\2\3/g' board/sunxi/Makefile and manually retabbing a few lines to line up again. The board descriptions could certainly be improved. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Kconfig: Make SPL_FEL a toplevel Kconfig optionIan Campbell2014-11-051-0/+5
| | | | | | | | | | | | | | It's unfortunate that this needs to be present in both .config and spl/.config since it makes it slightly hard to enable FEL mode for a regular defconfig. It can be done with: echo CONFIG_SPL_FEL=y >> .config echo CONFIG_SPL_FEL=y >> spl/.config Ideally only one of those would be needed. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: kconfig: Rename TARGET_SUN[45678]I to MACH_SUN[45678]I.Ian Campbell2014-11-051-10/+10
| | | | | | | | | | | | | Now we have CONFIG_ARCH_SUNXI as the toplevel, CONFIG_MACH_SUN[45678]I as the per-SoC option and leave CONFIG_TARGET_BLAH free for individual boards in the future. Done automatically with: sed -i -e 's/TARGET_\(SUN[45678]I\)/MACH_\1/g' $(git grep -l TARGET_SUN[45678]I) Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: kconfig: Add top-level ARCH_SUNXIIan Campbell2014-11-051-1/+29
| | | | | | | | | | | And make TARGET_SUN[45678]I a choice variable under this. configs updated with: sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/* Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* ARM: sunxi: Fix Ippo-q8h-v5 defconfig filenameChen-Yu Tsai2014-11-051-1/+1
| | | | | | | | | | The defconfig for Ippo-q8h-v5 was incorrectly committed as "Ippo_q8h". This patch renames it correctly, as well as correct a typo in my name in the maintainers listing. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* kconfig: arm: introduce symbol for ARM CPUsGeorges Savoundararadj2014-10-291-3/+0
| | | | | | | | | | | | | | | | | This commit introduces a Kconfig symbol for each ARM CPU: CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136, CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100. Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected for CPU_ARM1176 and CPU_V7. For each target, the corresponding CPU is selected and the definition of SYS_CPU in the corresponding Kconfig file is removed. Also, it removes redundant "string" type in some Kconfig files. Signed-off-by: Georges Savoundararadj <savoundg@gmail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
* sunxi: Add CONFIG_OLD_SUNXI_KERNEL_COMPAT Kconfig optionHans de Goede2014-10-241-0/+7
| | | | | | | | | | | | | | Add a Kconfig option which users can select when they want to boot older kernels, e.g. the linux-sunxi 3.4 kernels. For now this just forces the pll5 "p" value to 1 (divide by 2) as that is what those kernels are hardcoded too, in the future this may enable further workarounds. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Tom Rini <trini@ti.com> -- Changes in v2: -s/CONFIG_OLD_KERNEL_COMPAT/CONFIG_OLD_SUNXI_KERNEL_COMPAT. -Move the code block setting P(1) for old kernels to where P gets cleared
* ARM: sunxi: Add Ippo-q8h-v5 A23 tablet board defconfigChen-Yu Tsai2014-10-241-0/+5
| | | | | | | | | | | Ippo q8h is a series of A23 tablet boards. This defconfig is for v5 of these boards, though for u-boot purposes they are mostly the same. See: http://linux-sunxi.org/Ippo_q8h Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: sunxi: Add basic A23 supportChen-Yu Tsai2014-10-241-1/+2
| | | | | | | | | | | The basic blocks of the A23 are similar to the A31 (sun6i). Re-use sun6i code for initial clock, gpio, and uart setup. There is no SPL support for A23, as we do not have any documentation or sample code for DRAM initialization. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Kconfig: Unify sunxi Kconfig codeHans de Goede2014-10-241-27/+5
| | | | | | | | Unify the sunxi Kconfig code, instead of having separate code blocks for each of sun4i - sun7i. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Use PG3 - PG8 as io-pins for mmc1Hans de Goede2014-10-241-3/+3
| | | | | | | | | | None of the known sunxi devices actually use mmc1 routed through PH, where as some devices do actually use mmc1 routed through PG, so change the routing of mmc1 to PG. If in the future we encounter devices with mmc1 routed through PH, we will need to change things to be a bit more flexible. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: When we've both mmc0 and mmc2, detect from which one we're bootingHans de Goede2014-10-241-2/+28
| | | | | | | | | | | | | sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're booting, and make that one "mmc dev 0" so that a single u-boot binary can be used for both the onboard eMMC and for external sdcards. When we're booting from mmc2, we make it dev 0 because that is where the SPL will load the tertiary payload (the actual u-boot binary in our case) from, see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Turn MMC_SUNXI_SLOT_EXTRA into a proper Kconfig optionHans de Goede2014-10-242-1/+9
| | | | | | | | | Note we also drop the SPL check for initializing the 2nd mmc slot, the SPL check is not necessary with Kconfig, because only options explicitly marked as also being for the SPL get set during SPL builds. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add mmc card-detect functionalityHans de Goede2014-10-241-0/+26
| | | | | Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: sun6i: Add Colombus board defconfigChen-Yu Tsai2014-10-241-0/+5
| | | | | | | | | | | | | The Colombus board is an A31 evaluation board from WITS Technology. Maxime has kindly agreed to maintain this board. [1] http://lists.denx.de/pipermail/u-boot/2014-September/190043.html Signed-off-by: Chen-Yu Tsai <wens@csie.org> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: sunxi: Add basic A31 supportMaxime Ripard2014-10-241-1/+9
| | | | | | | | | | | Add a new sun6i machine that supports UART and MMC. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: use SPDX labels, adapt to Kconfig system, drop ifdef around mmc and smp code, drop MACH_TYPE] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add support for the Mele M3 boardHans de Goede2014-10-242-0/+2
| | | | | | | | | | | | | The Mele M3 is yet another Allwinnner based Android top set box from Mele. It uses a housing similar to the A2000, but without the USM sata storage slot at the top. It features an A20 SoC, 1G RAM, 4G eMMC (unique for Allwinner devices), 100Mbit ethernet, HDMI out, 3 USB A receptacles, VGA, and A/V OUT connections. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun7i: Add support for Olimex A20-OLinuXino-LIME2Iain Paton2014-10-243-0/+38
| | | | | | | | | | This adds support for the Olimex A20-OLinuXino-Lime2 https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXIno-LIME2 Differences to previous Lime boards are 1GB RAM and gigabit ethernet Signed-off-by: Iain Paton <ipaton0@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Fix gmac not working reliable on the BananapiHans de Goede2014-10-081-0/+9
| | | | | | | | | | | | | | | | | | | | | In order for the gmac nic to work reliable on the Bananapi, we need to set bits 10-12 GTXDC "GMAC Transmit Clock Delay Chain" of the GMAC clk register (0x01c20164) to 3. Without this about 9 out of 10 ethernet packets get lost, with this setting there is no packet loss. So far setting these bits is only necessary on the Bananapi, so this commit solves this with a bit of #ifdef CONFIG_BANANAPI code. If in the future we need to do something similar for other boards, we can create a specific CONFIG_FOO option for this then. Reported-by: Karsten Merker <merker@debian.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Karsten Merker <merker@debian.org> Tested-by: Zoltan HERPAI <wigyori@openwrt.org> Tested-by: Tony Zhang <tony.zhang@lemaker.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* kconfig: remove redundant "string" type in arch and board KconfigsMasahiro Yamada2014-09-131-6/+0
| | | | | | | | | | | | | | | | | | Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME} are specified in arch/Kconfig. We can delete the ones in arch and board Kconfig files. This commit can be easily reproduced by the following command: find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e ' /config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ { N s/\n[[:space:]]*string// } ' Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* sun7i: Add support for Olimex A20-OLinuXino-LIMEFUKAUMI Naoki2014-09-053-0/+38
| | | | | | | This patch adds support for Olimex A20-OLinuXino-LIME board. Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Correct typo CONFIG_FTDFILE => CONFIG_FDTFILEIan Campbell2014-09-051-2/+2
| | | | | | | | | | | | Patch is the result of: sed -i -e 's/FTDFILE/FDTFILE/g' board/sunxi/Kconfig configs/* include/configs/sunxi-common.h sed -i -e 's/ftdfile/fdtfile/g' board/sunxi/Kconfig Reported-by: Vagrant Cascadian <vagrant@debian.org> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> [ ijc -- s/Spotted-by/Reported-by/ and resolve conflict vs "remove redundant "SPL" from CONFIG_SYS_EXTRA_OPTIONS" ]
* sunxi: Add environment settings to make extlinux.conf booting workHans de Goede2014-08-121-0/+3
| | | | | | | | | | | | Automatic booting using an extlinux.conf file requires various environment variables to be set. Also modify CONFIG_SYS_LOAD_ADDR and CONFIG_STANDALONE_LOAD_ADDR to match the value chosen for kernel_addr_r, see the added comment for why the new value is chosen. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Stephen Warren <swarren@nvidia.com>
* sunxi: Kconfig: move common settings into a shared code blockHans de Goede2014-08-121-26/+6
| | | | | | | | SYS_CPU, SYS_BOARD and SYS_SOC are identical for all sunxi boards, move them to a shared code block. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun7i: Add bananapi boardHans de Goede2014-07-313-0/+33
| | | | | | | | | | | The Banana Pi is an A20 based development board using Raspberry Pi compatible IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi and stereo audio out + various expansion headers: http://www.lemaker.org/ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun7i: Add support for a number of new sun7i boardsHans de Goede2014-07-315-0/+102
| | | | | | | | | | Add support for boards which I own and which already have a dts file in the upstream kernel. Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun5i: Add support for a number of new sun5i boardsHans de Goede2014-07-314-0/+69
| | | | | | | | | | Add support for boards which I own and which already have a dts file in the upstream kernel. Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sun4i: Add support for a number of new sun4i boardsHans de Goede2014-07-317-2/+169
| | | | | | | | | | Add support for boards which I own and which already have a dts file in the upstream kernel. Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ahci: provide sunxi SATA driver using AHCI platform frameworkIan Campbell2014-07-312-0/+85
| | | | | | | | | | | | | | | | | | | | | This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done for sun7i only since I don't have access to any other sunxi platforms with sata included. The PHY setup is derived from the Alwinner releases and Linux, but is mostly undocumented. The Allwinner AHCI controller also requires some magic (and, again, undocumented) DMA initialisation when starting a port. This is added under a suitable ifdef. This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on contents of Linux DTS files, including SATA power pin config taken from the DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Add board MAINTAINERS filesMasahiro Yamada2014-07-301-0/+19
| | | | | | | | | | | | | | | | | | | | We have switched to Kconfig and the boards.cfg file is going to be removed. We have to retrieve the board status and maintainers information from it. The MAINTAINERS format as in Linux Kernel would be nice because we can crib the scripts/get_maintainer.pl script. After some discussion, we chose to put a MAINTAINERS file under each board directory, not the top-level one because we want to collect relevant information for a board into a single place. TODO: Modify get_maintainer.pl to scan multiple MAINTAINERS files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Suggested-by: Tom Rini <trini@ti.com> Acked-by: Simon Glass <sjg@chromium.org>
* kconfig: add board Kconfig and defconfig filesMasahiro Yamada2014-07-301-0/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds: - arch/${ARCH}/Kconfig provide a menu to select target boards - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig set CONFIG macros to the appropriate values for each board - configs/${TARGET_BOARD}_defconfig default setting of each board (This commit was automatically generated by a conversion script based on boards.cfg) In Linux Kernel, defconfig files are located under arch/${ARCH}/configs/ directory. It works in Linux Kernel since ARCH is always given from the command line for cross compile. But in U-Boot, ARCH is not given from the command line. Which means we cannot know ARCH until the board configuration is done. That is why all the "*_defconfig" files should be gathered into a single directory ./configs/. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
* sunxi: add Cubieboard2 supportIan Campbell2014-07-182-0/+32
| | | | | | | | This is a sun7i (A20) based followup to the sun4i (A10) Cubieboard. It has GMAC using MII mode. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: use random parts of SID to set ethaddrJonathan Liu2014-07-181-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | Similar to the USB NIC found on OMAP5uEVM, PandaBoard and BeagleBoard-XM boards, the sunxi SoCs have a NIC onboard without an embedded MAC address. Just like the omap used on these boards, the sunxi SoCs do have a unique chip id, in the form of the 128 bit SID register: http://linux-sunxi.org/SID_Register_Guide So mimick the BeagleBoard-XM board code (commit 548a64d8) and use the chip id to generate a unique fixed MAC address. We check for the SID not being all 0, since some early A20 batches shipped without having there SID programmed. Note we use specific parts of the 128 bits, since some parts indicate the SoC family / revision, and thus are fixed. The algorithm for this was taken from the linux-sunxi.org kernels. Signed-off-by: Jonathan Liu <net147@gmail.com> [hdegoede@redhat.com: Expanded the commit message with some more info] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
OpenPOWER on IntegriCloud