summaryrefslogtreecommitdiffstats
path: root/board/freescale/mpc8641hpcn
Commit message (Collapse)AuthorAgeFilesLines
* powerpc/86xx: remove empty board_early_init_f()Timur Tabi2011-04-281-5/+0
| | | | | | | Remove an empty board_early_init_f() from the MPC8641HPCN board. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Refactor fsl_ddr_get_spd into common code from boardKumar Gala2011-04-041-30/+0
| | | | | | | | | | | | | | Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards pretty much do the same thing. The only variations are in how many controllers or DIMMs per controller exist. To make this work we standardize on the names of the SPD_EEPROM_ADDRESS defines based on the use case of the board. We allow boards to override get_spd to either do board specific fixups to the SPD data or deal with any unique behavior of how the SPD eeproms are wired up. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Replace fsl_ddr_get_mem_data_rate with get_ddr_freq()Kumar Gala2011-04-041-6/+1
| | | | | | | | | | Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq() and every 86xx board uses get_bus_freq(). If implement get_ddr_freq() as a static inline to call get_bus_freq() we can remove fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq() directly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Move cpu specific lmb reserve to arch_lmb_reserveKumar Gala2011-04-041-10/+1
| | | | | | | | We've been utilizing board_lmb_reserve to reserve the boot page for MP systems. We can just move this into arch_lmb_reserve for 85xx & 86xx systems rather than duplicating in each board port. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Convert MPC8641HPCN to use common SRIO init codeKumar Gala2011-01-141-4/+1
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Rework MPC8641HPCN pci_init_board to use common FSL PCIe codeKumar Gala2011-01-142-53/+2
| | | | | | | | Remove duplicated code in MPC8641HPCN board and utilize the common fsl_pcie_init_board(). We also now dynamically setup the LAWs for PCI controllers based on which PCIe controllers are enabled. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Replace is_fsl_pci_cfg with is_serdes_configuredKumar Gala2011-01-141-3/+2
| | | | | | | Now that we have serdes support for all 85xx/86xx/Pxxx chips we can replace the is_fsl_pci_cfg() code with the is_serdes_configured(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* hwconfig: Fix dummy initialization of {board, cpu}_hwconfigKumar Gala2010-11-301-3/+0
| | | | | | | | | | | | | | | | Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a default value they will get put into the BSS if they aren't defined elsewhere. This is problematic as we try to utilize hwconfig before we've relocated and thus BSS isn't setup. Instead of giving dummy values in the board files that utilize this feature, we can just initialize the variables to an empty string and thus move them out of the BSS if they aren't defined elsewhere. Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated with string pointers vs arrays. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Switch from archive libraries to partial linkingSebastien Carlier2010-11-171-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | Before this commit, weak symbols were not overridden by non-weak symbols found in archive libraries when linking with recent versions of binutils. As stated in the System V ABI, "the link editor does not extract archive members to resolve undefined weak symbols". This commit changes all Makefiles to use partial linking (ld -r) instead of creating library archives, which forces all symbols to participate in linking, allowing non-weak symbols to override weak symbols as intended. This approach is also used by Linux, from which the gmake function cmd_link_o_target (defined in config.mk and used in all Makefiles) is inspired. The name of each former library archive is preserved except for extensions which change from ".a" to ".o". This commit updates references accordingly where needed, in particular in some linker scripts. This commit reveals board configurations that exclude some features but include source files that depend these disabled features in the build, resulting in undefined symbols. Known such cases include: - disabling CMD_NET but not CMD_NFS; - enabling CONFIG_OF_LIBFDT but not CONFIG_QE. Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
* fsl: Clean up printing of PCI boot infoPeter Tyser2010-11-141-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously boards used a variety of indentations, newline styles, and colon styles for the PCI information that is printed on bootup. This patch unifies the style to look like: ... NAND: 1024 MiB PCIE1: connected as Root Complex Scanning PCI bus 01 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex Scanning PCI bus 0d 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d In: serial ... Signed-off-by: Peter Tyser <ptyser@xes-inc.com> CC: wd@denx.de CC: sr@denx.de CC: galak@kernel.crashing.org
* 86xx: Create common linker scriptKumar Gala2010-10-201-133/+0
| | | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8641hpcn: Update PCI codePeter Tyser2010-10-201-75/+22
| | | | | | | Update to use the recent, common FSL PCI initialization code. Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Makefile: move all Power Architecture boards into boards.cfgWolfgang Denk2010-10-181-28/+0
| | | | | | | | | | Clean up Makefile, and drop a lot of the config.mk files on the way. We now also automatically pick all boards that are listed in boards.cfg (and with all configurations), so we can drop the redundant entries from MAKEALL to avoid building these twice. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-181-1/+1
| | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* powerpc/8xxx: Fix bug in memctrl interleaving & bank interleaving on cs0~cs4york2010-07-261-0/+2
| | | | | | | | | Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual rank with 512MB each rank. Also check dimm size and rank size for memory controller interleaving Signed-off-by: York Sun <yorksun@freescale.com>
* powerpc/85xx & 86xx: Rework ft_fsl_pci_setup to not require aliasesKumar Gala2010-07-201-6/+1
| | | | | | | | | | | Previously we used an alias the pci node to determine which node to fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to find the node to update. Additionally, we replace the code in each board with a single macro call that makes assumes uniform naming and reduces duplication in this area. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Rename PCI1/2 to PCIE1/2 on MPC8641HPCN & SBC8641Kumar Gala2010-07-202-38/+38
| | | | | | | | The MPC8641 boards actually only have PCIE not PCI. Rename so we are uniform with regards to names so we can replace this code with templated code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/86xx: Move PCI/PCIe address defines into common immap_86xx.hKumar Gala2010-07-201-2/+2
| | | | | | | | Remove dupliacted setting of PCI/PCIe address and offsets in board config.h. Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on MPC8641 boards since its really PCIE controllers and not PCI. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move arch/ppc to arch/powerpcStefan Roese2010-04-211-7/+7
| | | | | | | | | | | | | | | | | As discussed on the list, move "arch/ppc" to "arch/powerpc" to better match the Linux directory structure. Please note that this patch also changes the "ppc" target in MAKEALL to "powerpc" to match this new infrastructure. But "ppc" is kept as an alias for now, to not break compatibility with scripts using this name. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Anatolij Gustschin <agust@denx.de>
* ppc: Move cpu/$CPU to arch/ppc/cpu/$CPUPeter Tyser2010-04-131-6/+6
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Rename lib_generic/ to lib/Peter Tyser2010-04-131-2/+2
| | | | | | | | Now that the other architecture-specific lib directories have been moved out of the top-level directory there's not much reason to have the '_generic' suffix on the common lib directory. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Move lib_$ARCH directories to arch/$ARCH/libPeter Tyser2010-04-131-1/+1
| | | | | | | | | Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk This change is intended to clean up the top-level directory structure and more closely mimic Linux's directory organization. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* fsl: improve the PIXIS code and fix a few bugsTimur Tabi2010-04-071-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Refactor and document the Freescale PIXIS code, used on most 85xx and 86xx boards. This makes the code easier to read and more flexible. Delete pixis.h, because none of the exported functions were actually being used by any other file. Make all of the functions in pixis.c 'static'. Remove "#include pixis.h" from every file that has it. Remove some unnecessary #includes. Make 'pixis_base' into a macro, so that we don't need to define it in every function. Add "while(1);" loops at the end of functions that reset the board, so that execution doesn't continue while the reset is in progress. Replace in_8/out_8 calls with clrbits_8, setbits_8, or clrsetbits_8, where appropriate. Replace ulong/uint with their spelled-out equivalents. Remove unnecessary typecasts, changing the types of some variables if necessary. Add CONFIG_SYS_PIXIS_VCFGEN0_ENABLE and CONFIG_SYS_PIXIS_VBOOT_ENABLE to make it easier for specific boards to support variations in the PIXIS registers sets. No current boards appears to need this feature. Fix the definition of CONFIG_SYS_PIXIS_VBOOT_MASK for the MPC8610 HPCD. Apparently, "pixis_reset altbank" has never worked on this board. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc86xx: set the DDR BATs after calculating true DDR sizeTimur Tabi2010-03-301-0/+2
| | | | | | | | | | | | | | | | | | | | After determining how much DDR is actually in the system, set DBAT0 and IBAT0 accordingly. This ensures that the CPU won't attempt to access (via speculation) addresses outside of actual memory. On 86xx systems, DBAT0 and IBAT0 (the BATs for DDR) are initialized to 2GB and kept that way. If the system has less than 2GB of memory (typical for an MPC8610 HPCD), the CPU may attempt to access this memory during speculation. The zlib code is notorious for generating such memory reads, and indeed on the MPC8610, uncompressing the Linux kernel causes a machine check (without this patch). Currently we are limited to power of two sized DDR since we only use a single bat. If a non-power of two size is used that is less than CONFIG_MAX_MEM_MAPPED u-boot will crash. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 86xx: Remove redundant code in initdramBecky Bruce2009-11-041-5/+0
| | | | | | | | The same code exists both inside an #ifdef and outside of it. Remove the extra code for all the 86xx boards. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc: Enable full relocation to RAMPeter Tyser2009-10-031-1/+0
| | | | | | | | | | | | | The following changes allow U-Boot to fully relocate from flash to RAM: - Remove linker scripts' .fixup sections from the .text section - Add -mrelocatable to PLATFORM_RELFLAGS for all boards - Define CONFIG_RELOC_FIXUP_WORKS for all boards Previously, U-Boot would partially relocate, but statically initialized pointers needed to be manually relocated. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* ppc/8xxx: Refactor code to determine if PCI is enabled & agent/hostKumar Gala2009-09-081-3/+2
| | | | | | | | | | | Refactor the code into a simple bitmask lookup table that determines if a given PCI controller is enabled and if its in host/root-complex or agent/end-point mode. Each processor in the PQ3/MPC86xx family specified different encodings for the cfg_host_agt[] and cfg_IO_ports[] boot strapping signals. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 86xx: Remove redudant PLATFORM_CPPFLAGSKumar Gala2009-08-281-3/+0
| | | | | | | | | | | | For historic reasons we had defined some additional PLATFORM_CPPFLAGS like: PLATFORM_CPPFLAGS += -DCONFIG_MPC86xx=1 PLATFORM_CPPFLAGS += -DCONFIG_MPC8641=1 However these are all captured in the config.h and thus redudant. Also moved common 86xx flags into cpu/mpc86xx/config.mk. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* pci/fsl_pci_init: Fold fsl_pci_setup_inbound_windows into fsl_pci_initKumar Gala2009-08-281-6/+0
| | | | | | | | Every platform that calls fsl_pci_init calls fsl_pci_setup_inbound_windows before it calls fsl_pci_init. There isn't any reason to just call it from fsl_pci_init and simplify things a bit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* pci/fsl_pci_init: Fold pci_setup_indirect into fsl_pci_initKumar Gala2009-08-281-4/+2
| | | | | | | | Every platform that calls fsl_pci_init calls pci_setup_indirect before it calls fsl_pci_init. There isn't any reason to just call it from fsl_pci_init and simplify things a bit. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 85xx/86xx: Replace in8/out8 with in_8/out_8 on FSL boardsKumar Gala2009-07-221-6/+9
| | | | | | | The pixis code used in8/out8 all over the place. Replace it with in_8/out_8 macros. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 86xx: Rename ccsr_ddr's sdram_mode_1, sdram_cfg_1 fieldsPeter Tyser2009-07-221-3/+3
| | | | | | | | Rename sdram_mode_1 to sdram_mode and sdram_cfg_1 to sdram_cfg to match the 86xx user's manual and other Freescale architectures Signed-off-by: Peter Tyser <ptyser@xes-inc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 86xx: Report which "bank" of NOR flash we are booting from on MPC8641HPCNKumar Gala2009-07-221-4/+14
| | | | | | | | | | | | | | The MPC8641HPCN board is capable of swizzling the upper address bit of the NOR flash we boot out of which creates the concept of "virtual" banks. This is useful in that we can flash a test of image of u-boot and reset to one of the virtual banks while still maintaining a working image in "bank 0". The PIXIS FPGA exposes registers on LBC which we can use to determine which "bank" we are booting out of (as well as setting which bank to boot out of). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl_pci: Move prototypes into fsl_pci.h and remove explicit externsKumar Gala2009-04-041-6/+0
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl_pci: Renamed immap_fsl_pci.h to fsl_pci.hKumar Gala2009-04-041-1/+1
| | | | | | | Rename the pci header for FSL HW so we can move some prototypes in there and stop doing explicit externs Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 86xx: Cleanup MP supportKumar Gala2009-04-011-1/+1
| | | | | | | | | | | | | | * Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx * Introduce determine_mp_bootpg() helper. We'll need this to address a bug introduced in v2009.03 with 86xx MP booting. We have to make sure to reserve the region of memory used for the MP bootpg() so other u-boot code doesn't use it. * Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to allow cmd_mp.c to build and work. In the future we should look at implementing all these functions. This could be common w/85xx if we use spin tables on 86xx. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8641hpcn/sbc8641d: Add missing board_lmb_reservesBecky Bruce2009-03-311-0/+9
| | | | | | | | | | | | We're missing the board_lmb_reserve definitions that allow cpu_mp_lmb_reserve to be called; this means that Linux is free to reallocate reserved pages. Linux currently boots because we're getting lucky - the page we've reserved is high enough in memory that it isn't allocated by Linux while we still need it to be in existence. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix all linker script to handle all rodata sectionsTrent Piepho2009-03-201-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A recent gcc added a new unaligned rodata section called '.rodata.str1.1', which needs to be added the the linker script. Instead of just adding this one section, we use a wildcard ".rodata*" to get all rodata linker section gcc has now and might add in the future. However, '*(.rodata*)' by itself will result in sub-optimal section ordering. The sections will be sorted by object file, which causes extra padding between the unaligned rodata.str.1.1 of one object file and the aligned rodata of the next object file. This is easy to fix by using the SORT_BY_ALIGNMENT command. This patch has not be tested one most of the boards modified. Some boards have a linker script that looks something like this: *(.text) . = ALIGN(16); *(.rodata) *(.rodata.str1.4) *(.eh_frame) I change this to: *(.text) . = ALIGN(16); *(.eh_frame) *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) This means the start of rodata will no longer be 16 bytes aligned. However, the boundary between text and rodata/eh_frame is still aligned to 16 bytes, which is what I think the real purpose of the ALIGN call is. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
* mpc8641hpcn: Indicate 36-bit addr map in boot messagesBecky Bruce2009-02-231-0/+3
| | | | | | | If 36-bit addressing is enabled, print a message on the console when we boot. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* 86xx: Reset updatePeter Tyser2009-02-161-0/+8
| | | | | | | | | | Update the 86xx reset sequence to try executing a board-specific reset function. If the board-specific reset is not implemented or does not succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard reset procedure than the previous method and allows all board peripherals to be reset if needed. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* mpc8641hpcn: Clean up PCI mapping conceptsBecky Bruce2009-02-101-5/+5
| | | | | | | | | Clean up PCI mapping concepts in the 8641 config - rename _BASE to _BUS, as it's actually a PCI bus address, separate virtual and physical addresses into _VIRT and _PHYS, and use each appopriately. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* mpc8641hpcn: Set up outbound pci windows before inboundBecky Bruce2009-02-101-6/+6
| | | | | | | | | | Because the inbound pci windows are mapped generously, set up the more specific outbound windows first. This way, when we search the pci regions for something, we will hit on the more specific region. This can actually be a problem on systems with large amounts of RAM. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
* fsl-ddr: use the 1T timing as default configurationDave Liu2009-01-231-0/+2
| | | | | | | | | For light loaded system, we use the 1T timing to gain better memory performance, but for some heavily loaded system, you have to add the 2T timing options to board files. Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com>
* Align end of bss by 4 bytesSelvamuthukumar2008-11-181-0/+1
| | | | | | | | | | Most of the bss initialization loop increments 4 bytes at a time. And the loop end is checked for an 'equal' condition. Make the bss end address aligned by 4, so that the loop will end as expected. Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc8641: fix address-cells default in old .dts detectionBecky Bruce2008-11-111-3/+3
| | | | | | | | address-cells defaults to 2, not 1; so in the unlikely event that it isn't specified, this patch is required for correct operation. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc8641: Try to detect old .dts filesBecky Bruce2008-11-101-0/+27
| | | | | | | | | | | | | Since we've changed the memory map of the board, be nice and add some checking to try to catch out-of-date .dts files. We do this by checking the CCSRBAR location in the .dts and comparing it to the CCSRBAR location in u-boot. If they don't match, a warning msg is printed. This isn't foolproof, but it's simple and will catch most of the cases where an out-of-date .dts is present, including all of the cases where a new u-boot is used with an old standard MPC8641 .dts file as supplied with Linux. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc8641: Support 36-bit physical addressingBecky Bruce2008-11-101-6/+7
| | | | | | | | | | | | | | | | | | This patch creates a memory map with all the devices in 36-bit physical space, in addition to the 32-bit map. The CCSR relocation is moved (again, sorry) to allow for the physical address to be 36 bits - this requires translation to be enabled. With 36-bit physical addressing enabled, we are no longer running with VA=PA translations. This means we have to distinguish between the two in the config file. The existing region name is used to indicate the virtual address, and a _PHYS variety is created to represent the physical address. Large physical addressing is not enabled by default. Set CONFIG_PHYS_64BIT in the config file to turn this on. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc8641: Change 32-bit memory mapBecky Bruce2008-11-102-11/+14
| | | | | | | | | | | | | | | | | | | | | | The memory map on the 8641hpcn is modified to look more like the 85xx boards; this is a step towards a more standardized layout going forward. As part of this change, we now relocate the flash. The regions for some of the mappings were far larger than they needed to be. I have reduced the mappings to match the actual sizes supported by the hardware. In addition I have removed the comments at the head of the BAT blocks in the config file, rather than updating them. These get horribly out of date, and it's a simple matter to look at the defines to see what they are set to since everything is right here in the same file. Documentation has been changed to reflect the new map, as this change is user visible, and affects the OS which runs post-uboot. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* mpc8641: Drop imaginary second flash bank, map 8MBBecky Bruce2008-11-101-1/+1
| | | | | | | | | There's a lot of setup and foo for the second flash bank. The problem is, this board doesn't actually have one. Clean this up. Also, the flash is 8M in size. Get rid of the confusing aliased overmapping, and just map 8M. Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* Merge commit 'wd/master'Jon Loeliger2008-11-102-9/+9
|\
OpenPOWER on IntegriCloud