summaryrefslogtreecommitdiffstats
path: root/board/freescale/common/vid.c
Commit message (Collapse)AuthorAgeFilesLines
* armv8/ls2080ardb: Enable VID supportRai Harninder2016-03-291-1/+14
| | | | | | | | This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder <harninder.rai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* freescale: vid: Return i2c mux to default channelWenbin Song2016-03-211-3/+9
| | | | | | | | IR chip is on one of the channels on multiplexed I2C-bus. Reset to default channel after accessing. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* powerpc/board/t4240rdb: Enable VID supportYing Zhang2016-01-251-1/+1
| | | | | | | | | | | | The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
* board/freescale/common: Check IR chip mode for VID supportYing Zhang2016-01-251-1/+16
| | | | | | | | | IR chip on all the boards are required to be used in Intel mode to support VID. VDD will not be adjusted if IR chip is used in other modes. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8/ls1043aqds: add LS1043AQDS board supportShaohui Xie2015-11-301-0/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1043AQDS Specification: ------------------------- Memory subsystem: * 2GByte DDR4 DIMM * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two RGMII ports * XFI 10G port * SGMII * QSGMII with 4x 1G ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> [York Sun: Add CONFIG_SYS_NS16550=y in defconfig] Reviewed-by: York Sun <yorksun@freescale.com>
* powerpc/t208xqds: VID supportYing Zhang2014-12-051-0/+491
The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
OpenPOWER on IntegriCloud