summaryrefslogtreecommitdiffstats
path: root/board/atmel/at91sam9x5ek/at91sam9x5ek.c
Commit message (Collapse)AuthorAgeFilesLines
* ARM: atmel: at91sam9x5ek: enable spl supportBo Shen2015-04-011-0/+74
| | | | | | | Enable SPL support for at91sam9x5ek board. Now, it supports boot up from NAND flash and SPI flash. Signed-off-by: Bo Shen <voice.shen@atmel.com>
* arm: atmel: at91sam9x5: cleanup cs configure for spiBo Shen2013-12-171-1/+0
| | | | | | | | | As the cs for spi is worked in gpio mode, so no need to configure it as peripheral and then configure to gpio. Configure it to gpio directly. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* at91sam9x5: enable USB support for 9x5ek board.Richard Genoud2012-12-091-0/+3
| | | | | | Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* ARM: at91sam9x5: enable MCI0 support for 9x5ek board.Wu, Josh2012-10-171-0/+10
| | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91sam9x5: set default EBI I/O drive configuration.Wu, Josh2012-09-131-0/+4
| | | | | | | This patch configure at91sam9x5's EBI drive I/O. Without this, When SD card boot, the nand flash read/write are not stable. Which will cause kernel MTD test fail (Since mainline kernel doesn't configure the EBI register). Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* at91: 9x5: change SMC config timing that both works for PMECC & non-PMECC.Wu, Josh2012-09-011-6/+6
| | | | | | Signed-off-by: Josh Wu <josh.wu@atmel.com> Tested-by: voice.shen@atmel.com Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm : at91sam9x5 : fix a small bug for NANDBo Shen2012-09-011-0/+2
| | | | | | | | | fix a bug: when not boot from NAND, the NAND flash can not be detected. Using this to fix it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm : Atmel : add at91sam9x5ek board supportBo Shen2012-09-011-0/+293
Add at91sam9x5ek board support, this board support the following SoCs AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35 Using at91sam9x5ek_nandflash to configure for the board Now only supports NAND with software ECC boot up Signed-off-by: Bo Shen <voice.shen@atmel.com> [move MAINTAINERS entry to right place] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
OpenPOWER on IntegriCloud