summaryrefslogtreecommitdiffstats
path: root/board/atmel/at91sam9263ek/at91sam9263ek.c
Commit message (Collapse)AuthorAgeFilesLines
* Write MAC address automatically on MACB-based boardsBen Warren2010-07-121-7/+0
| | | | | | Also, remove all calls to eth_init() in boards that use MACB Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* ARM change name of defines for AT91 arm926ejsAchim Ehrlich2010-03-071-1/+1
| | | | | | | | | | Configuration defines should be preceeded with CONFIG_SYS_. Renamed some at91 specific defines to conform to this naming convention: AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
* update at91sam9263ek board to new SoC accessJens Scharsig2010-02-121-75/+76
| | | | | | | * convert at91sam9263ek board to use c stucture SoC access * change gpio access to at91_gpio syntax Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* at91sam9260/9263: add back up for the rst(reset controller).Sedji Gaouaou2009-07-061-1/+5
| | | | | | | | | On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was set to 0 after being set to 500 ms for the PHY reset. Do backup the old reset length and restore it after the MACB initialisation. Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: Stelian Pop <stelian@popies.net>
* at91sam9263ek: add nor flash supportJean-Christophe PLAGNIOL-VILLARD2009-06-211-1/+18
| | | | | | this will allow you to store use it for the env and to boot directly U-Boot from Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: improve clock frameworkJean-Christophe PLAGNIOL-VILLARD2009-04-161-1/+2
| | | | | | calculate dynamically the clock rate and pllb setting for usb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move nand drivers to drivers/mtd/nandJean-Christophe PLAGNIOL-VILLARD2009-03-221-2/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common macb initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-22/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common usb host initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-10/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common spi initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-15/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9/at91cap: move common serial initialisation to cpuJean-Christophe PLAGNIOL-VILLARD2009-03-221-28/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* AT91: Use AT91_CPU_CLOCK in displaysStelian Pop2008-11-211-1/+1
| | | | | | | | | | Introduce AT91_CPU_CLOCK and use it for displaying the CPU speed in the LCD driver. Also make AT91_MAIN_CLOCK and AT91_MASTER_CLOCK reflect the corresponding board clocks. Signed-off-by: Stelian Pop <stelian@popies.net>
* AT91: Replace AT91_BASE_EMAC by the board specific values.Stelian Pop2008-11-071-1/+1
| | | | | | | | AT91_BASE_EMAC is never used outside the board specific files, so replace its usage by the board specific AT91xxx_BASE_EMAC. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* AT91: Replace (undefined) AT91_ID_US* by the board specific values.Stelian Pop2008-11-071-3/+3
| | | | | | | | | | | | AT91_ID_US0 / AT91_ID_US1 / AT91_ID_US2 were used but never defined. Since they are never used outside the board specific files, they can be replaced by the board specific AT91xxx_ID_US0 / AT91xxx_ID_US1 / AT91xxx_ID_US2. Bug spotted by Jesus Alvarez <jalvarez@micromint.com>. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* lcd: Let the board code show board-specific infoHaavard Skinnemoen2008-10-271-0/+29
| | | | | | | | | | | | | The information displayed when CONFIG_LCD_INFO is set is inherently board-specific, so it should be done by the board code. The current code dealing with this only handles two cases, and is already a horrible mess of #ifdeffery. Yes, this duplicates some code, but it also allows boards to print more board-specific information; this used to be very difficult. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-181-2/+2
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Moved initialization of Ethernet controllers on Atmel AT91 to board_eth_init()Ben Warren2008-09-021-0/+11
| | | | | | Removed at91sam9_eth_initialize() from net/eth.c Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
* [AT91SAM9] Fix NAND FLASH timingsPatrice Vilchez2008-07-051-2/+2
| | | | | | | | | | | | Fix NAND FLASH timings for at91sam9x evaluation kits. New timings are based on application note "NAND Flash Support on AT91SAM9 Microcontrollers" available at http://atmel.com/dyn/resources/prod_documents/doc6255.pdf Signed-off-by: Patrice Vilchez <patice.vilchez@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Stelian Pop <stelian@popies.net>
* Fix boot from NOR due to incorrect reset delay.Stelian Pop2008-07-051-1/+6
| | | | | | | | | | | | | | | | | | | | | | AT91 RSTC registers are battery-backuped, so their values are not reset across power cycles. One of those registers, the AT91_RSTC_MR register, is being modified by U-Boot, in the ethernet initialisation routine, to generate a 500ms user reset. Unfortunately, this value is not being restored afterwards, causing subsequent resets to also last for 500ms. This long reset sequence causes problems (at least) in the boot sequence from NOR: by the time the CPU tries to load a program from the NOR flash, the latter is still in reset and not yet available. Additionaly, this patch fixes a bug in the original code which caused the reset delay to last for 2s instead of 500ms. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* AT91SAM9263EK: hook up the ATMEL LCD driverStelian Pop2008-05-101-0/+65
| | | | | | | | | This patch makes the necessary adaptations (PIO configurations and defines in config header file) to hook up the Atmel LCD driver to the AT91SAM9263EK board. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* AT91SAM9263EK supportStelian Pop2008-05-101-0/+240
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK board. Signed-off-by: Stelian Pop <stelian@popies.net> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
OpenPOWER on IntegriCloud