summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-mvebu/dram.c
Commit message (Collapse)AuthorAgeFilesLines
* arm: mvebu: Move SoC selection (A38X vs AXP) into KconfigStefan Roese2016-01-141-7/+4
| | | | | | | | | | | | | | | | | | Until now, the SoC selection for the ARCH_MVEBU platforms has been done in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As it needed to get selected for AXP and A38x based boards. This patch now changes this to move the SoC selection to Kconfig. And also uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x. This makes things a bit clearer - especially for new board additions. Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available CONFIG_ARMADA_38X and CONFIG_ARMADA_XP. And CONFIG_DDR3 is removed, as its not referenced anywhere. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: Print CPU and SDRAM frequency upon startupStefan Roese2016-01-141-2/+9
| | | | | | | | | | | | | | | With this patch, the CPU and the DDR frequencies will get printed in the U-Boot startup messages. Resulting in such a log: U-Boot 2016.01-rc2-00188-gb8eeaec-dirty (Dec 21 2015 - 12:32:35 +0100) SoC: MV78460-B0 at 1600 MHz I2C: ready DRAM: 4 GiB (800 MHz, ECC not enabled) ... Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: Add complete SDRAM ECC scrubbingStefan Roese2015-08-171-6/+135
| | | | | | | | | | | | This patch introduces the SDRAM scrubbing for ECC enabled board to fill/initialize the ECC bytes. This is done via the XOR engine to speed up the process. The scrubbing is a 2-stage process: 1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot 2) U-Boot scrubs the remaining SDRAM area(s) Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: dram.c: Rework dram_init() and dram_init_banksize()Stefan Roese2015-08-171-9/+21
| | | | | | | | | | | | | Rework these functions so that dram_init_banksize() does not call dram_init() again. It only needs to set the banksize values in the bdinfo struct. Make sure to also clip the size of the last bank if it exceeds the maximum allowed value of 3 GiB (0xc000.0000). Otherwise other address windows (e.g. PCIe) will overlap with this memory window. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: Display ECC enabled / disabled upon bootupStefan Roese2015-08-171-0/+19
| | | | | | | | | This patch adds "(ECC enabled)" or "(ECC disabled)" to the DRAM bootup text. Making it easier for board with SPD DIMM's to see, if ECC is enabled or not. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu/armada100: dram.c: Remove CONFIG_SYS_BOARD_DRAM_INITStefan Roese2015-08-171-2/+0
| | | | | | | | CONFIG_SYS_BOARD_DRAM_INIT is not defined anywhere. So lets get rid of all references here. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
* arm: mvebu: Move mvebu-common into mach-mvebuStefan Roese2015-05-051-0/+144
Now that the mach-mvebu directory exists and is used by Armada XP we can move the mvebu-common files into this directory as well. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com> Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
OpenPOWER on IntegriCloud