summaryrefslogtreecommitdiffstats
path: root/arch/arm/include
Commit message (Collapse)AuthorAgeFilesLines
* OMAP5: emif/ddr: Change emif settings as required for ES1.0 silicon.SRICHARAN R2012-05-151-2/+70
| | | | | | | | | The OMAP5 silicon has new DDR PHY design, which includes a external PHY as well. So configuring the ext PHY parameters here. Also the EMIF timimg registers and a couple of DDR mode registers needs to be updated based on the testing from the actual silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: io: Configure the io settings for omap5430 sevm board.SRICHARAN R2012-05-151-24/+104
| | | | | | | | | The control module provides options to set various signal integrity parameters like the output impedance, slew rate, load capacitance for different pad groups. Configure these as required for the omap5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: board: Add pinmux data for omap5_evm board.SRICHARAN R2012-05-151-252/+250
| | | | | | Adding the full pinmux data for OMAP5430 sevm board. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP5: clocks: Change clock settings as required for ES1.0 silicon.SRICHARAN R2012-05-151-3/+16
| | | | | | | | Aligning all the clock related settings like the dpll frequencies, their respective clock outputs, etc to the ideal values recommended for OMAP5430 ES1.0 silicon. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* OMAP4460: TPS Ensure SET1 is selected after voltage configurationNishanth Menon2012-05-152-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms. Currently we control this pin with a mux configuration as part of boot sequence. Current configuration results in the following voltage waveform: |---------------| (SET1 default 1.4V) | --------(programmed voltage) | <- (This switch happens on mux7,pullup) vdd_mpu(TPS) -----/ (OPP boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -----------------------/ (OPP boot voltage) Problem 1) |<----- Tx ------>| timing violation for a duration Tx close to few milliseconds. Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP. By using GPIO as recommended as standard procedure by TI, the sequence changes to: -------- (programmed voltage) vdd_mpu(TPS) ------------/ (Opp boot voltage) --------- (programmed voltage) vdd_core(TWL6030) -------------/ (OPP boot voltage) NOTE: This does not attempt to address OMAP5 - Aneesh please confirm Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* OMAP3+: Introduce generic logic for OMAP voltage controllerNishanth Menon2012-05-154-30/+4
| | | | | | | | | | | | | | | | | | | | OMAP Voltage controller is used to generically talk to PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code in multiple SoC code, introduce a common voltage controller logic which can be re-used from elsewhere. With this change, we replace setup_sri2c with omap_vc_init which has the same functionality, and replace the voltage scale replication in do_scale_vcore and do_scale_tps62361 with omap_vc_bypass_send_value. omap_vc_bypass_send_value can also now be used with any configuration of PMIC. NOTE: Voltage controller controlling I2C_SR is a write-only data path, so no register read operation can be implemented. Reported-by: Isabelle Gros <i-gros@ti.com> Reported-by: Jerome Angeloni <j-angeloni@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM:OMAP+:MMC: Add parameters to MMC initJonathan Solnit2012-05-154-5/+9
| | | | | | | | | | Add parameters to the OMAP MMC initialization function so the board can mask host capabilities and set the maximum clock frequency. While the OMAP supports a certain set of MMC host capabilities, individual boards may be more restricted and the OMAP may need to be configured to match the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example. Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
* serial: add LPC32X0 high-speed UART devices supportVladimir Zapolskiy2012-05-151-0/+60
| | | | | | | | | This change adds an implementation of high-speed UART found on NXP LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* arm926ejs: add NXP LPC32x0 cpu series supportVladimir Zapolskiy2012-05-158-0/+606
| | | | | | | | This change adds initial support for NXP LPC32x0 SoC series. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Marek Vasut <marek.vasut@gmail.com>
* i2c: Add support for designware i2c controllerVipin KUMAR2012-04-241-146/+0
| | | | | | | | | | | | | Earlier, a driver exists in the u-boot source for designware i2c interface. That driver was specific to spear platforms. This patch implements the i2c controller as a generic driver which can be used by multiple platforms The driver files are now renamed to designware_i2c.c and designware_i2c.h and these are moved into drivers/i2c folder for reusability by other platforms Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
* DMA: Split the APBH DMA init into block and channel initMarek Vasut2012-04-161-1/+3
| | | | | | | | | | | | | | | | | | | | | | | This fixes the issue where mxs_dma_init() was called either twice or never, without introducing any new init hooks. The idea is to allow each and every device using the APBH DMA block to configure and request only the channels it uses, instead of making it call init for all the channels as is now. The common DMA block init part, which only configures the block, is then called from CPUs arch_cpu_init() call. NOTE: This patch depends on: http://patchwork.ozlabs.org/patch/150957/ Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* imx: Remove unneeded/repititive definitions from imx headersVikram Narayanan2012-04-163-6/+0
| | | | | | | Remove gpio related unused/repititive definitions from imx headers. Signed-off-by: Vikram Narayanan <vikram186@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
* i.MX6: define CACHELINE_SIZEEric Nelson2012-04-161-0/+2
| | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de>
* tegra: i2c: Add I2C driverYen Lin2012-03-291-0/+157
| | | | | | | | | | | | | Add basic i2c driver for Tegra2 with 8- and 16-bit address support. The driver requires CONFIG_OF_CONTROL to obtain its configuration from the device tree. (Simon Glass: sjg@chromium.org modified for upstream) Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Enhance clock support to handle 16-bit clock divisorsSimon Glass2012-03-291-2/+8
| | | | | | | | I2C ports have a 16-bit clock divisor. Add code to handle this special case so that I2C speeds below 150KHz are supported. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASESimon Glass2012-03-291-2/+2
| | | | | | | | | Change this name to fit with the current convention in the Tegra header file. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: usb: Add support for Tegra USB peripheralSimon Glass2012-03-292-0/+254
| | | | | | | | | | | | | | | | | | This adds basic support for the Tegra2 USB controller. Board files should call board_usb_init() to set things up. Configuration is performed through the FDT, with aliases used to set the order of the ports, like this fragment: aliases { /* This defines the order of our USB ports */ usb0 = "/usb@0xc5008000"; usb1 = "/usb@0xc5000000"; }; drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* tegra: fdt: Add function to return peripheral/clock IDSimon Glass2012-03-291-0/+13
| | | | | | | | | A common requirement is to find the clock ID for a peripheral. This is the second cell of the 'clocks' property (the first being the phandle itself). Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* EXYNOS: Add structure for Exynos4 DMCChander Kashyap2012-03-271-0/+109
| | | | | | | Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC). Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* arm: Add Prep subcommand support to bootmSimon Schwarz2012-03-271-0/+26
| | | | | | | | | | | | | Adds prep subcommand to bootm implementation of ARM. When bootm is called with the subcommand prep the function stops right after ATAGS creation and before announce_and_cleanup. This is used in command "cmd_spl export" Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* omap-common/spl: Add linux boot to SPLSimon Schwarz2012-03-271-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | This adds Linux booting to the SPL This depends on CONFIG_MACH_TYPE patch by Igor Grinberg (http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809) Related CONFIGs: CONFIG_SPL_OS_BOOT Activates/Deactivates the OS booting feature CONFIG_SPL_OS_BOOT_KEY defines the IO-pin number u-boot switch - if pressed u-boot is booted CONFIG_SYS_NAND_SPL_KERNEL_OFFS Offset in NAND of direct boot kernel image to use in SPL CONFIG_SYS_SPL_ARGS_ADDR Address where the kernel boot arguments are expected - this is normaly RAM-begin + 0x100 Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* devkit8000/spl: init GPMC for dm9000 in SPLSimon Schwarz2012-03-271-0/+1
| | | | | | | | | Linux crashes if the GPMC isn't configured for the dm9000. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* mx6: Read silicon revision from registerFabio Estevam2012-03-271-0/+142
| | | | | | | | | | | | | | | Instead of hardcoding the mx6 silicon revision, read it in run-time. Also, besides the silicon version print the mx6 variant type: quad,dual/solo or solo-lite. Tested on a mx6qsabrelite, where it shows: CPU: Freescale i.MX6Q rev1.0 at 792 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
* mx6: Remove duplicate definition of ANATOP_BASE_ADDRFabio Estevam2012-03-271-1/+0
| | | | | | Remove duplicate definition of ANATOP_BASE_ADDR. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* IXP: Fix GPIO_INT_ACT_LOW_SET()Marek Vasut2012-03-261-2/+8
| | | | | | | | | The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7. This is due to the fact that there are two registers for total of 16 lines. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* SPL: Add YMODEM over UART load supportMatt Porter2012-03-261-0/+3
| | | | | | | | | | Adds support for loading U-Boot from UART using YMODEM protocol. If YMODEM support is enabled in SPL and the romcode indicates that SPL loaded via UART then SPL will wait for start of a YMODEM transfer via the console port. Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
* Fix erroneous 32-bit access to hw_clkctrl_frac0 and hw_clkctrl_frac1 registersRobert Delien2012-03-261-31/+13
| | | | | | | | | This patch fixes erroneous 32-bit access to registers hw_clkctrl_frac0 and hw_clkctrl_frac1. Signed-off-by: Robert Delien <robert@delien.nl> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
* Introducing 8-bit wide register, mx28_register_8Robert Delien2012-03-261-0/+16
| | | | | | | | | | This patch introduces an 8-bit register, mx28_register_8, in order to prepare for fixing erroneous 32-bit wide access of registers hw_clkctrl_frac0 and hw_clkctrl_frac1. Signed-off-by: Robert Delien <robert@delien.nl> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
* Renamed mx28_register to mx28_register_32 to prepare for mx28_register_8Robert Delien2012-03-2614-417/+421
| | | | | | | | | This patch renames mx28_register to mx28_register_32 in order to prepare for the introduction of an 8-bit register, mx28_register_8. Signed-off-by: Robert Delien <robert@delien.nl> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Marek Vasut <marex@denx.de>
* usb/ehci: Add USB support for the MX6QWolfgang Grandegger2012-03-262-0/+4
| | | | | | | Currently, only USB Host 1 is supported. Cc: Remy Bohmer <linux@bohmer.net> Signed-off-by: Wolfgang Grandegger <wg@denx.de>
* i.mx28: Added register definitions for DIGCTL registersRobert Delien2012-03-262-0/+156
| | | | | | | This patch adds register definitions for the registers of the DIGCTL IP-block. Signed-off-by: Robert Delien <robert@delien.nl>
* USB: Armada100: EHCI Driver for Armada100 SOCsAjay Bhargav2012-03-191-0/+1
| | | | | | This patch adds support for USB EHCI driver for Armada100 SOCs. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* USB: Armada100: Add UTMI PHY interface driverAjay Bhargav2012-03-192-0/+87
| | | | | | | This patch adds USB host controller's UTMI PHY interface driver for Armada100 SOCs. Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
* tt01: add video supportHelmut Raiger2012-02-271-0/+1
| | | | | | | | The video setup for the Epson display is provided. Addtionally some extra info is displayed next to the Linux logo. Make get_cpu_rev() publicly available (added to sys_proto.h). Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* net: fec_mxc: add 1000 Mbps selectionTroy Kisky2012-02-271-0/+1
| | | | | | | | Define FEC_QUIRK_ENET_MAC and add to arch-mx6/imx-regs.h Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
* am33xx: ddr_defs.h: Change DDR timingsChase Maupin2012-02-271-1/+1
| | | | | | | | * For cold silicon the DDR timings need to be relaxed in order for the device to boot with DDR at 266MHz * Fix proposed by James Doublesin Signed-off-by: Chase Maupin <Chase.Maupin@ti.com>
* mx6q: Add support for ECSPI through mxc_spi driverEric Nelson2012-02-271-0/+44
| | | | | | | Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org>
* mxc_spi: move machine specifics into CPU headersEric Nelson2012-02-273-0/+82
| | | | | | | | | | | | | | Move (E)CSPI register declarations into the imx-regs.h files for each supported CPU Introduce two new macros to control conditional setup MXC_CSPI - Used for processors with the Configurable Serial Peripheral Interface (MX3x) MXC_ECSPI - For processors with Enhanced Configurable... (MX5x, MX6x) Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <jason.hui@linaro.org> Tested-by: Jason Liu <jason.hui@linaro.org>
* mx6q: define GPIO macros for translating between ordinals and port:indexEric Nelson2012-02-271-0/+4
| | | | | | | | | | | | | | | | | The interface to the mxc_gpio driver uses integer (ordinal) values to refer to all GPIOs on the i.MX processors. The registers themselves and much of the i.MX documentation are banked in groups of 32, and these macros allow the use of the port:index numbering for clarity. GPIO_NUMBER() converts to ordinal value from port:index GPIO_PORT() returns the port of an ordinal value GPIO_INDEX() returns the index or offset of the ordinal. Discussion on the mailing list at http://lists.denx.de/pipermail/u-boot/2012-January/116927.html Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* omap_hsmmc: Wait for CMDI to be clearTom Rini2012-02-154-4/+4
| | | | | | | | | | | | | | | | | Before we can send a command we need both the DATI (command inhibit on mmc_dat line) bit and CMDI (command inhibit on mmc_cmd line) are clear. The previous behavior of only checking on DATI was insufficient on some cards and incorrect behavior in any case. This makes the code check for both bits being clear and makes the error print more clear as to what happened. DATI_CMDDIS is removed as it was unused elsewhere in the code and stood for 'DATI is set, cmds are disabled still'. Fix originally spotted by Peter Bigot. Tested-by: Peter A. Bigot <bigotp@acm.org> Tested-by: Robert Nelson <robertcnelson@gmail.com> Signed-off-by: Tom Rini <trini@ti.com> Tested-by: Andreas Müller <schnitzeltony@googlemail.com>
* Changes to move hawkboard to the new spl infrastructureSughosh Ganu2012-02-121-0/+9
| | | | | | | | | | | | | | | | | | This patch moves hawkboard to the new spl infrastructure from the older nand_spl one. Removed the hawkboard_nand_config build option -- The spl code now gets compiled with hawkboard_config, after building the main u-boot image, using the CONFIG_SPL_TEXT_BASE. Modified the README.hawkboard to reflect the same. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Christian Riesch <christian.riesch@omicron.at> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Tom Rini <trini@ti.com> Acked-by: Christian Riesch <christian.riesch@omicron.at>
* ARMV7: Fix duplicate use of "b" parameter in ACTIM_CTRLA definitionPeter Barada2012-02-121-28/+29
| | | | | | | | ACTIM_CTRLA macro errently passes "b" parameter to ACTIM_CTRLA_TRAS() instead of "c". To make usage more clear, replace all single-letter macro parameters with more descriptive parameter names. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
* davinci: add support for printing clock frequencyHadli, Manjunath2012-02-121-0/+3
| | | | | | | | | add support for printing various clock frequency info found in SOC such as ARM core frequency, DSP core frequency and DDR frequency as part of bdinfo command. Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com> Cc: Tom Rini <trini@ti.com>
* AM3517: Changed default clock rate for AM3517Schuyler Patton2012-02-121-1/+1
| | | | | | | | | | | | AM3517: Changed default clock rate for AM3517 Changed #define MPU_M_13_ES2 from 0x1F4 to 0x258, this allows the AM3517 to boot up at 600MHz instead of 500 MHz Signed-off-by: Schuyler Patton <spatton@ti.com> CC: Tom Rini <tom.rini@gmail.com> CC: Simon Schwarz <simonschwarzcor@gmail.com> CC: Stefano Babic <sbabic@denx.de>
* OMAP3+: Clock: Adding ehci clock enablingGovindraj.R2012-02-121-0/+1
| | | | | | | | | | Adding ehci clock enabling mechanism part of clock framework. When essential clocks are enabled during init phase usb host clocks can also be enabled from clock framework. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Tested-by: Stefano Babic <sbabic@denx.de>
* ehci-omap: Clean up added ehci-omap.cGovindraj.R2012-02-123-24/+212
| | | | | | | | | | | | | | | | | | Clean up added ehci-omap.c and make it generic for re-use across omap-soc having same ehci ip block. Also pass the modes to be configured from board file and configure the ports accordingly. All usb layers are not cache aligned, till then keep cache off for usb ops as ehci will use internally dma for all usb ops. * Add a generic common header ehci-omap.h having common ip block data and reg shifts. * Rename and modify ehci-omap3 to ehci.h retain only conflicting sysc reg shifts remove others and move to common header file. * pass the board data for beagle/panda accordinly to use ehci ports. Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
* ARM: EXYNOS: Add support for Exynos5 based SoCsChander Kashyap2012-02-125-7/+651
| | | | | | | | Samsung's ARM Cortex-A15 based SoCs are known as Exynos5 series of SoCs. This patch adds the support for Exynos5. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* S5P: support generic watchdog timerMinkyu Kang2012-02-123-1/+64
| | | | | | | | This patch adds support the generic watchdog timer for s5pc1xx and exynos4 Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: HeungJun, Kim <riverful.kim@samsung.com>
* ARMV7: Exynos4: Add supoort power for Exynos4HeungJun, Kim2012-02-122-0/+231
| | | | | | | | This patch adds power.h and SAMSUNG_BASE() macro for using Exynos4 power. Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* ARMV7: Exynos4: Add watchdog.h for Exynos4HeungJun, Kim2012-02-121-0/+53
| | | | | | | | This patch add watchdog.h for Exynos4 Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
OpenPOWER on IntegriCloud