summaryrefslogtreecommitdiffstats
path: root/arch/arm/include/asm/arch-sunxi
Commit message (Collapse)AuthorAgeFilesLines
* sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3Siarhei Siamashka2015-11-221-1/+6
| | | | | | | | | | | | | | | | | | | | | The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz on Allwinner H3 and using PLL6 as the clock source (PLL6/3). This can be verified by reading the value of the AHB1_APB1_CFG_REG register via /dev/mem. It always reads as 0x3180 regardless of the current cpufreq operating point. So this configuration should be safe for use in U-Boot too. PLL6 also needs to be configured before it is used as the clock source, according to the "CCU / Programming Guidelines" section of the Allwinner manual. The current low AHB1 clock speed is limiting the USB transfer speed when booting via FEL. This patch can increase the FEL USB transfer speed from ~510 KB/s to ~950 KB/s. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add H3 DRAM initialization supportJens Kuske2015-11-223-0/+190
| | | | | | | | Based on existing A23/A33 code and the original H3 boot0. Signed-off-by: Jens Kuske <jenskuske@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add basic H3 supportJens Kuske2015-11-221-0/+1
| | | | | | | | Add initial sun8i H3 support, only uart + mmc are supported for now. Signed-off-by: Jens Kuske <jenskuske@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: retrieve FEL-provided values to environment variablesBernhard Nortmann2015-09-291-0/+5
| | | | | | | | | | | | | | | | | | | This patch extends the misc_init_r() function on sunxi boards to test for the presence of a suitable "sunxi" SPL header. If found, and the loader ("fel" utility) provided a non-zero value for the boot.scr address, then the corresponding environment variable fel_scriptaddr gets set. misc_init_r() also sets (or clears) the "fel_booted" variable depending on the active boot device, using the same logic as spl_boot_device(). The goal is to provide sufficient information (within the U-Boot environment) to make intelligent decisions on how to continue the boot process, allowing specific customizations for the "FEL boot" case. Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: (mksunxiboot) signature to indicate "sunxi" SPL variantBernhard Nortmann2015-09-291-1/+18
| | | | | | | | | | | | | | | | | | | | | | This patch follows up on a discussion of ways to improve support for the sunxi FEL ("USB boot") mechanism, especially with regard to boot scripts, see: https://groups.google.com/d/msg/linux-sunxi/wBEGUoLNRro/rHGq6nSYCQAJ The idea is to convert the (currently unused) "pad" bytes in the SPL header into an area where data can be passed to U-Boot. To do this safely, we have to make sure that we're actually using our "sunxi" flavor of the SPL, and not the Allwinner boot0. The modified mksunxiboot introduces a special signature to the SPL header in place of the "pub_head_size" field. This can be used to reliably distinguish between compatible versions of sunxi SPL and anything else (older variants or Allwinner's boot0). Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: move SPL-related definitions to platform-specific includeBernhard Nortmann2015-09-291-12/+20
| | | | | | | | | | | | | The sunxi platform currently doesn't seem to make any use of the asm/arch-sunxi/spl.h file. This patch moves some declarations from tools/mksunxiboot.c into it. This enables us to reuse those definitions when extending the sunxi board code (boards/sunxi/boards.c). Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Enable non-secure access to RTC on sun6i (A31s)Chen-Yu Tsai2015-08-311-0/+23
| | | | | | | | | | | | | | On the A31s the RTC is by default secured. Thus when u-boot loads the kernel in non-secure world, the RTC is unavailable. The SoC has a TrustZone Protection Controller, which can be used to enable non-secure access to the RTC. On the A31 the TZPC doesn't seem to do anything, i.e. changes to its register contents do not affect access to the RTC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sun6i: clock: Add support for the mipi pllHans de Goede2015-08-142-0/+15
| | | | | | | | Add support for the mipi pll, this is necessary for getting higher dotclocks with lcd panels. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: clock: Add clock_get_pll3() helper functionHans de Goede2015-08-142-0/+8
| | | | | | | Add a helper function to get the pll3 clock rate. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: display: Fix composite video out on sun5iHans de Goede2015-08-142-1/+16
| | | | | | | | The tv-encoder on sun5i is slightly different compared to the one on sun4i/sun7i. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: display: Add a few extra register and constant definesHans de Goede2015-08-083-6/+42
| | | | | | | | | | | | | Add a few extra sunxi display registers and constant defines. Also rename some existing defines (e.g. dropping _GCTRL) and make some more generic (e.g. dropping the 2x scaling from SUNXI_LCDC_TCON1_TIMING_V_TOTAL). This is a preparation patch for adding composite video out support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb-phy: Never power off the usb portsHans de Goede2015-08-081-0/+1
| | | | | | | | | | | | | | | | | | | | | USB devices are not really designed to get the power bounced off and on at them. Esp. USB powered harddisks do not like this. Currently we power off the USB ports both on a "usb reset" and when booting the kernel, causing the usb-power to bounce off and then back on again. This patch removes the powering off calls, fixing the undesirable power bouncing. Note this requires some special handling for the OTG port: 1) We must skip the external vbus check if we've already enabled our own vbus to avoid false positives 2) If on an usb reset we no longer detect that the id-pin is grounded, turn off vbus as that means an external vbus may be present now Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: nand: Add pinmux and clock settings for NAND supportKarol Gugala2015-08-082-0/+3
| | | | | | | | | | To enable NAND flash in sunxi SPL, pins 0-6, 8-22 and 24 on port C are configured. Signed-off-by: Karol Gugala <kgugala@antmicro.com> Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSBPaul Kocialkowski2015-08-051-1/+1
| | | | | | | | | USB-related options are usually prefixed with CONFIG_USB and platform-specific adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* sunxi: musb: Move musb config and platdata to the sunxi-musb glueHans de Goede2015-07-251-0/+7
| | | | | | | | | Move the musb config and platdata to the sunxi-musb glue, which is where it really belongs. This is preparation patch for adding device-model support for the sunxi-musb-host code. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb-phy: Add support for reading otg id pin valueHans de Goede2015-07-251-0/+1
| | | | | | | | Add support for reading the id pin value of the otg connector to the usb phy code. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Create helper function veryfing valid boot signature on MMCDaniel Kochmański2015-07-241-0/+1
| | | | | | | | | | | | | | | This patch extracts checking for valid SD card "eGON.BT0" signature from `board_mmc_init` into function `sunxi_mmc_has_egon_boot_signature`. Buffer for mmc sector is allocated and freed at runtime. `panic` is triggered on malloc failure. Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu> CC: Roy Spliet <r.spliet@ultimaker.com> Cc: Ian Campbell <ijc@hellion.org.uk> [hdegoede@redhat.com: Small bugfix to make it work for devs other then mmc0] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add support for UART0 in PB pin group on A33Chen-Yu Tsai2015-07-051-0/+1
| | | | | | | | The A33 adds a pinmux function for UART0 in the PB pin group. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Revert "sunxi/nand: Add support to the SPL for loading u-boot from internal ↵Ian Campbell2015-06-282-69/+0
| | | | | | | | | | | | | | NAND memory" This reverts commit f76eba38b3eda905ff3bdc18dd1240d3dcbc6e5a. This patch did not have a full and proper copyright/S-o-b chain. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Conflicts: include/configs/sun6i.h include/configs/sun8i.h
* sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memoryDaniel Kochmański2015-05-292-0/+69
| | | | | | | | | | | This commit adds support to the sunxi SPL to load u-boot from the internal NAND. Note this only adds support to access the boot partitions to load u-boot, full NAND support to load the kernel, etc. from the nand data partition will come later. Signed-off-by: Roy Spliet <r.spliet@ultimaker.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Match sun4i, sun6i, sun9i CCI definitions for NAND and DMARoy Spliet2015-05-293-3/+10
| | | | | | | | | Make sure definitions for NAND clock and DMA gate bits are the same across boards. Signed-off-by: Roy Spliet <r.spliet@ultimaker.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Add DMA definitionsRoy Spliet2015-05-292-0/+84
| | | | | | Signed-off-by: Roy Spliet <r.spliet@ultimaker.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sun9i: Basic sun9i (A80) supportHans de Goede2015-05-291-0/+1
| | | | | | | Add initial sun9i (A80) support, only uart + mmc are supported for now. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: video: Fix lvds panel support for sun6i+Hans de Goede2015-05-192-0/+15
| | | | | | | | | We've never tested the lvds panel support on sun6i+ SoCs until now, and unsurprisingly the lvds code needed some fixes to work on my ga10h A33 tablet with lvds panel. This makes the panel on that tablet actually work. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Make DRAM_ODT_EN Kconfig setting a boolHans de Goede2015-05-192-2/+2
| | | | | | | | | | | | | | | | | Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of only in dram_sun4i.c and hardcoding odt_en elsewhere. Note this commit makes no functional changes for existing boards, its purpose is to allow changing the odt_en value on future A33 boards. For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs currently do) this patch turns on odt for both the DQ and the DQS lines, whereas previously it was possibly (but not desirable) to turn odt on only for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
* sunxi: add support for UART2 on A23/A33Laurent Itti2015-05-191-0/+1
| | | | | | | | | | Add support for UART2 (2-pin version but note that RTS/CTS pins are available pn that port for possible future use), can be selected in config by using CONFIG_CONS_INDEX=3 Signed-off-by: Laurent Itti <laurentitti@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: ohci: Add ohci usb host controller supportHans de Goede2015-05-142-0/+4
| | | | | | | | | | | | | This commit adds support for the OHCI companion controller, which makes usb-1 devices directly plugged into to usb root port work. Note for now this switches usb-keyboard support for sunxi back from int-queue support to the old interrupt polling method. Adding int-queue support to the ohci code and switching back to int-queue support is in the works. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb: Do not call phy_probe from hcd codeHans de Goede2015-05-041-2/+2
| | | | | | | | | | | | | | | | | | | The 2/3 usb-phys on the sunxi SoCs are really a single separate functional block, and are modelled as such in devicetree. So once we've moved all the sunxi usb code to the driver-model then phy_probe will be called once for the entire block from the driver-model enumeration code. Move to this now as this also avoids problems with phy_probe being called multiple times once we introduce ohci support. This also allows us to get rid of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed to be called only once. Since we're effectively rewriting the probe / remove functions, move them to the end of the file while we are at it, as that is the most logical place for them. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb: Rename the usbc.? files to usb_phy.?Hans de Goede2015-05-041-0/+0
| | | | | | | | The usbc.? files now only contain usb-phy related code, rename them to make this clear. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb: Rename sunxi_usbc_foo functions to sunxi_usb_phy_barHans de Goede2015-05-041-14/+11
| | | | | | | | | | | Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear that these are usb-phy functions. Also change the verbs & nouns in the suffix to match the verbs & nouns used in the Linux kernels generic phy framework. This patch purely renames things, it contains no functional changes. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb: Remove sunxi_usbc_get_io_base functionHans de Goede2015-05-041-1/+0
| | | | | | | | | | | This is the only function left in sunxi/usbc.c which is not phy related, so remove it. This is a preparation patch for turning the usbc.c code into a proper usb phy driver. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp: Remove non driver-model support from the axp gpio codeHans de Goede2015-05-041-7/+0
| | | | | | | | | | | | | | Now that all sunxi boards are using driver-model for gpio (*), we can remove the non driver-model support from the axp gpio code, and the glue to call into the axp gpio code from the sunxi_gpio non driver-model code. *) For the regular u-boot build, SPL still uses non driver-model gpio for now, but the SPL never uses axp gpios support and we were already not building axp-gpio support for the SPL. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: gmac: Move sunxi_gmac_initialize proto out of netdev.hHans de Goede2015-05-041-0/+3
| | | | | | | | | | | netdev.h should not be included in driver-model enabled builds (doing so causes compiler warnings about struct eth_driver not being declared), but we do use sunxi_gmac_initialize in the driver-model case, so move it out of netdev.h . Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp: Add driver-model support to the axp_gpio codeHans de Goede2015-05-041-2/+4
| | | | | | | | | | Add driver-model support to the axp_gpio code, note that this needs a small tweak to the driver-model version of sunxi_name_to_gpio to deal with the vbus detect and enable pins which are not standard numbered gpios. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp: Move axp gpio code to a separate axpi-gpio driverHans de Goede2015-05-041-0/+13
| | | | | | | | | | | | | | | | | | | | Move the axp-gpio code out of the drivers/power/axp*.c code, and into a new separate axpi-gpio driver. This change drops supports for the gpio3 pin on the axp209, as that requires special handling, and no boards are using it. Besides cleaning things up by moving the code to a separate driver, as a bonus this change also adds support for the (non vusb) gpio pins on the axp221 and the gpio pins on the axp152. The new axp-gpio driver gets its own Kconfig option, and is only enabled on boards which need it. Besides that it only gets enabled in the regular u-boot build and not for the SPL as we never need it in the SPL. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: axp: Move axp pmic register helpers to a separate fileHans de Goede2015-05-041-0/+18
| | | | | | | | | | | Move the register helpers used to access the registers via p2wi resp. rsb bus on the otherwise identical axp221 and axp223 pmics to a separate file, so that they can be used by the upcoming standalone axp gpio driver too. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add a33 dram init codeVishnu Patekar2015-05-042-0/+181
| | | | | | | | | | | | Based on Allwinner dram init code from the a33 bsp: https://github.com/allwinner-zh/bootloader/blob/master/basic_loader/bsp/bsp_for_a33/init_dram/mctl_hal.c Initial u-boot port by Vishnu Patekar, major cleanup / rewrite by Hans de Goede. Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Add support for A33 PLL11 (second DRAM pll)Hans de Goede2015-05-041-3/+28
| | | | | | | Add support for the new second DRAM PLL found on the A33 SoC. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: s/sun8i/sun8i_a23/Hans de Goede2015-05-042-2/+2
| | | | | | | | This is a preparation patch for adding A33 support, which will have a mach name of sun8i-a33. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig boolHans de Goede2015-05-043-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i have a various things in common, like having separate ahb reset control registers, the SID living inside the pmic, custom pmic busses, new style watchdog, etc. This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be used to check for these features avoiding the need for an ever growing list of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more "new style" sunxi SoCs. Note that this commit changes the behavior of the gmac and hdmi code for sun8i and the upcoming sun9i devices. This does not matter as sun8i does not have gmac nor hdmi, and sun9i has new hardware-blocks for these so the old code will not work there. Also this is intentional as if a sun8i / sun9i variant which does use the old hwblocks shows up then the GEN_SUN6I code paths will be the right ones to use. For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Complete i2c support for each supported platformPaul Kocialkowski2015-04-153-1/+36
| | | | | | | | | | | Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms even have up to 5. This adds support for every controller on each supported platform, which is especially useful when using expansion ports on single-board- computers. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* i2c: mvtwsi: Support for up to 4 different controllersPaul Kocialkowski2015-04-151-1/+1
| | | | | | | | | | | | Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI controller. However, other platforms using MVTWSI may come with more: this is the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found on the same chip. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Heiko Schocher <hs@denx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: Complete mmc pin mux for each supported platform, configured with KconfigPaul Kocialkowski2015-04-151-1/+12
| | | | | | | | | | | | | Sunxi platforms have different possible mmc pin mux setups (except for mmc0), which are different across platforms. This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig options. This is especially relevant when a second (in addition to mmc0) port is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: GPIO pin mux hardware-feature-specific function index definesPaul Kocialkowski2015-04-151-41/+19
| | | | | | | | | | | Each hardware feature exposed through the GPIO pin mux is usually using the same function index (for a given port), so there is no need to define one value per pin: one value per hardware feature per port is sufficient, avoids duplication and makes everything easier to understand. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: common VBUS detection logic in usbcPaul Kocialkowski2015-04-151-0/+1
| | | | | | | | | | | | | VBUS detection could be needed not only by the musb code (to prevent host mode), but also by e.g. gadget drivers to start only when a cable is connected. In addition, this allows more flexibility in vbus detection, as it could easily be extended to other USBC indexes. Eventually, this would help making musb support independent from a hardcoded USB controller index (0). Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* power: axp221: Virtual VBUS detect and enable GPIOs to replace separate logicPaul Kocialkowski2015-04-151-0/+4
| | | | | | | | | This converts the VBUS detection and enable logic to GPIO instead of separate axp functions and checks that have to be used aside usual GPIO functions. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: gpio: Indentation fixPaul Kocialkowski2015-04-151-2/+2
| | | | | | Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* sunxi: musb: Fix some lo speed devices not working with musb hostHans de Goede2015-03-291-0/+1
| | | | | | | | | | | | | | | | The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a high speed squelch on usb reset deassert when a lo speed device is plugged in. The android kernel has a work around for this in the form of temporary disabling the phy's squelch detection on reset deassert, this commit adds the same workaround to the u-boot sunxi musb code, thereby fixing various usb lo speed devices not working. Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless keyboard/mouse combo receiver. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Fix sun5i mbus speed when booting old kernelsHans de Goede2015-02-211-0/+9
| | | | | | | | | Older linux-sunxi-3.4 kernels override our PLL6 setting with 300 MHz, halving the mbus frequency, so set it to 300 MHz ourselves and base the mbus divider on that. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: Normalise FEL supportSimon Glass2015-02-161-0/+10
| | | | | | | | | | | | Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of creating its own. There are some #ifdefs required in start.S. Future work will hopefully remove these. This series is available at u-boot-dm, branch sunxi-working. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
OpenPOWER on IntegriCloud