summaryrefslogtreecommitdiffstats
path: root/Makefile
Commit message (Collapse)AuthorAgeFilesLines
...
| * Rename ads5121 board into mpc5121adsWolfgang Denk2009-06-121-3/+3
| | | | | | | | | | | | | | | | | | We rename the board so we use a consistent name in U-Boot and in Linux. Also, we use this opportunity to move the board into the Freecale vendor directory. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: John Rigby <jcrigby@gmail.com>
| * Add support for Linux-like kallsysmsMike Frysinger2009-06-121-4/+13
| | | | | | | | | | | | | | The kernel stores address<->symbol names in it so things can be decoded at runtime. Do it in U-Boot, and we get nice symbol decoding when crashing. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
| * dm355 evm supportDavid Brownell2009-06-121-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller: http://c6000.spectrumdigital.com/evmdm355/revd/ Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling: http://focus.ti.com/docs/prod/folders/print/tms320dm355.html This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
| * ZOOM2 Add initial support for Zoom2Tom Rix2009-06-121-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zoom2 is a new board from Texas Instruments and LogicPD The logicpd web site is a good source for general information on this board. Please start looking here if the below links are broken. http://www.logicpd.com This is a pdf of the product http://www.logicpd.com/sites/default/files/1012659A_Zoom_OMAP34x-II_MDP_Brief.pdf This is the product description web page http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp This patch provides a zoom2 base target by copying zoom1 and by making some obvious changes. To configure, run make omap3_zoom2_config Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
| * ppc4xx: Add Sequoia RAM-booting targetStefan Roese2009-06-121-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds another build target for the AMCC Sequoia PPC440EPx eval board. This RAM-booting version is targeted for boards without NOR FLASH (NAND booting) which need a possibility to initially program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000) configured to setup the SDRAM, this debugger can load this RAM- booting image to the target address in SDRAM (in this case 0x1000000) and start it there. Then U-Boot's standard NAND commands can be used to program the NAND FLASH (e.g. "nand write ..."). Here the commands to load and start this image from the BDI2000: 440EPX>reset halt 440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin 440EPX>go 0x1000000 Please note that this image automatically scans for an already initialized SDRAM TLB (detected by EPN=0). This TLB will not be cleared. This TLB doesn't need to be TLB #0, this RAM-booting version will detect it and preserve it. So booting via BDI2000 will work and booting with a complete different TLB init via U-Boot works as well. Signed-off-by: Stefan Roese <sr@denx.de>
* | Prepare v2009.06Wolfgang Denk2009-06-141-1/+1
|/ | | | | | Update CHANGELOG, fix minor coding stylke issue. Update Makefile. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Prepare 2009.06-rc3Wolfgang Denk2009-06-101-1/+1
| | | | | | Update CHANGELOG Signed-off-by: Wolfgang Denk <wd@denx.de>
* Prepare v2009.06-rc2Wolfgang Denk2009-05-151-1/+1
| | | | | | Update CHANGELOG. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Prepare v2009.06-rc1Wolfgang Denk2009-05-011-2/+2
| | | | | | Update CHANGELOG. Signed-off-by: Wolfgang Denk <wd@denx.de>
* at91: remove lowlevel_init.SJean-Christophe PLAGNIOL-VILLARD2009-05-011-1/+0
| | | | | | | | | | | | lowlevel_init.S is not used any more so remove it. As consequence, we also don't have to generate u-boot.lds but can use a static version as before. This also fixes the out-of-tree build problem introduced with commit f0a2c7b4 "at91: add support for the PM9263 board" Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
* at91: add support for the PM9263 board of Ronetix GmbHIlko Iliev2009-04-161-0/+4
| | | | | | | | | | The PM9263 board is based on the AT91SAM9263-EK board. Here is the page on Ronetix website: http://www.ronetix.at/starter_kit_9263.html Signed-off-by: Ilko Iliev <iliev@ronetix.at> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* drivers/usb: regorganisationJean-Christophe PLAGNIOL-VILLARD2009-04-061-1/+3
| | | | | | | | | | | | | move to linux usb driver organisation as following drivers/usb/gadget drivers/usb/host drivers/usb/musb Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
* ARM: fix out-of-tree build of imx31_phycore_eetGuennadi Liakhovetski2009-04-051-0/+1
| | | | | | | Fix out-of-tree build of the imx31_phycore_eet target. Reported-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
* Add support for the AT91RM9200EK Board.Ulf Samuelsson2009-04-041-0/+3
| | | | | | | | | | | | | | | | | | | The AT91RM9200-EK Evaluation Board supports the AT91RM9200 ARM9-based 32-bit RISC microcontroller and enables real-time code development and evaluation. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507 with - NOR (cfi driver) - DataFlash - USB OHCI - Net - I2C (hard) Signed-off-by: Ulf Samuelsson <ulf@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9: add watchdog supportJean-Christophe PLAGNIOL-VILLARD2009-04-041-0/+1
| | | | | Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* tools/Makefile: Remove symlinks for remaining source filesPeter Tyser2009-04-041-2/+1
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* tools/Makefile: Remove symlinks for fdt targetsPeter Tyser2009-04-041-2/+1
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* tools/Makefile: Add libfdt/ to the include search pathPeter Tyser2009-04-041-1/+1
| | | | | | | This change makes the process of symlinking libfdt_internal.h unnecessary Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* tools: Remove unecessary symlinking of zlib.hPeter Tyser2009-04-041-1/+1
| | | | | | | | crc32.c uses the zlib.h header in include/u-boot/zlib.h. The symlink was previously necessary to give U-Boot's version of zlib.h precedence over the host computer's version of zlib.h. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Makefile: Add removal of *.exe files to clean targetPeter Tyser2009-04-041-1/+1
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Makefile: Make autoconf.mk a dependency of the depend targetPeter Tyser2009-04-041-8/+8
| | | | | | | | The original code did not generate autoconf.mk until after some targets dependencies had already been calculated, for example the directories in the SUBDIRS variable Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Blackfin: bf518f-ezbrd: new board portMike Frysinger2009-04-021-3/+3
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf526-ezbrd: new board portMike Frysinger2009-04-021-3/+3
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf538f-ezkit: new board portMike Frysinger2009-04-021-3/+3
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf527-ezkit: new board portMike Frysinger2009-04-021-2/+3
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Blackfin: bf548-ezkit: new board portMike Frysinger2009-04-021-2/+3
| | | | Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-04-021-1/+1
|\
| * s3c4510b: move specific code to soc directoryJean-Christophe PLAGNIOL-VILLARD2009-03-291-1/+1
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | MPC85xx: Add MPC8569MDS board supportHaiying Wang2009-03-301-0/+3
| | | | | | | | | | | | | | | | | | This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | drivers/twserial: Add protocol driver for "three wire serial" interface.Detlev Zundel2009-03-301-1/+2
|/ | | | | | This pretty unintelligent interface is used on some RTC chips. Signed-off-by: Detlev Zundel <dzu@denx.de>
* at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.Nicolas Ferre2009-03-221-2/+12
| | | | | | | | | | | | | | AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed. The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board. It is essentially the same, with a few minor differences. Here is the chip page on Atmel website: http://www.atmel.com/dyn/products/product_card.asp?part_id=4337 Signed-off-by: Justin Waters <justin.waters@timesys.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* at91sam9xeek: fix soc nameJean-Christophe PLAGNIOL-VILLARD2009-03-221-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Merge branch 'next' of ../nextWolfgang Denk2009-03-211-1/+19
|\
| * UBIFS: Implement read-only UBIFS support in U-BootStefan Roese2009-03-201-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The U-Boot UBIFS implementation is largely a direct copy from the current Linux version (2.6.29-rc6). As already done in the UBI version we have an "abstraction layer" to redefine or remove some OS calls (e.g. mutex_lock() ...). This makes it possible to use the original Linux code with very little changes. And by this we can better update to later Linux versions. I removed some of the Linux features that are not used in the U-Boot version (e.g. garbage-collection, write support). Signed-off-by: Stefan Roese <sr@denx.de> CC: Artem Bityutskiy <dedekind@infradead.org> CC: Adrian Hunter <ext-Adrian.Hunter@nokia.com>
| * Add LZO decompressor supportStefan Roese2009-03-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds LZO decompression support to U-Boot. It is needed for the upcoming UBIFS support, since UBIFS uses LZO as default compressor/ decompressor. Since we only support read-only in UBIFS, only the decompressor is needed. All this is copied with minor changes from the current Linux kernel version (2.6.28-rc8). This patch only implements this LZO decompressor support for PPC. Other platforms using UBIFS will have to add the required "include/asm/unaligned.h" as well. It should be fairly easy to copy this from the Linux source tree as I have done it for PPC in this patch. Signed-off-by: Stefan Roese <sr@denx.de>
| * Add support for the digsy MTC board.Grzegorz Bernacki2009-03-201-0/+16
| | | | | | | | | | | | This is the InterControl custom device based on the MPC5200B chip. Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
* | Prepare 2009.03Wolfgang Denk2009-03-211-1/+1
|/ | | | | | Update CHANGELOG Signed-off-by: Wolfgang Denk <wd@denx.de>
* 8xx: add support for new keymile kmsupx4 board.Heiko Schocher2009-03-181-0/+3
| | | | | | | | | | | | | This patch adds support for the kmsupx4 board from Keymile, based on a Freescale MPC852T CPU - serial console on SMC1 - 32 MB SDRAM - 32 MB NOR Flash - Ethernet over SCC3 - I2C Bitbang Signed-off-by: Heiko Schocher <hs@denx.de>
* 8xx, mgsuvd: rename board to a more generic nameHeiko Schocher2009-03-181-1/+1
| | | | | | | | | renaming the "mgsuvd" board port into "km8xx", because there come more similar boards from keymile. Compiling the mgsuvd board with "make mgsuvd_config" remains. Signed-off-by: Heiko Schocher <hs@denx.de>
* Prepare 2009.03-rc2Wolfgang Denk2009-03-151-1/+1
| | | | | | Update CHANEGLOG, fix minor coding style issue. Signed-off-by: Wolfgang Denk <wd@denx.de>
* sh: Add support 32-Bit Extended Address Mode to sh7785lcrYoshihiro Shimoda2009-03-121-1/+14
| | | | | | | | We can built 'make sh7785lcr_32bit_config'. And add new command "pmb" for this mode. This command changes PMB for using 512MB system memory. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* ARM: add an "eet" variant of the imx31_phycore boardGuennadi Liakhovetski2009-02-241-1/+5
| | | | | | | | | | The "eet" variant of the imx31_phycore board has an OLED display, using a s6e63d6 display controller on the first SPI interface, using GPIO57 as a chip-select for it. With this configuration you can display 256 colour BMP images in 16-bit RGB (RGB565) LCD mode. Signed-off-by: Guennadi Liakhovetski <lg@denx.de> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Update CHANGELOG; Prepare 2009.03-rc1Wolfgang Denk2009-02-231-2/+2
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Makefile: fix cleanupWolfgang Denk2009-02-221-1/+1
| | | | | | | Commit e4943ec5 moved the ARM boards to a vendor directory but forgot to adapt the cleanup rules in the Makefile Signed-off-by: Wolfgang Denk <wd@denx.de>
* sh: Fix rsk7203 in tree buildPeter Griffin2009-02-211-1/+1
| | | | Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-02-191-0/+4
|\
| * qong: support for Dave/DENX QongEVB-LITE boardIlya Yanok2009-02-101-0/+4
| | | | | | | | | | | | | | This patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board. Signed-off-by: Ilya Yanok <yanok@emcraft.com> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | MPC85xx: TQM8548: add support for the TQM8548_AG moduleWolfgang Grandegger2009-02-161-1/+2
| | | | | | | | | | | | | | | | The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory, CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module with "$ make TQM8548_AG_config". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
* | MPC85xx: TQM8548: add support for the TQM8548_BE moduleWolfgang Grandegger2009-02-161-4/+7
|/ | | | | | | | | The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN interface. With NAND support, the image is significantly larger and TEXT_BASE is adjusted accordingly. U-Boot can be built for this module with "$ make TQM8548_BE_config". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2009-02-011-7/+47
|\
OpenPOWER on IntegriCloud