summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* odroid: usbhost - Add missing gpio_request callSuriyan Ramasami2014-11-241-2/+11
| | | | | | | | | | | | | | | | The USB host code was missing gpio_request() calls before using the gpio functions, causing errors to be printed out. As a side note calls to max77686_set_buck_mode(OPMODE_OFF/OPMODE_ON) have been removed, as they did not have any effect. This is as per Przemyslaw: I looked into the documentation and there is a "ENB8" pin in PMIC package. This pin allows steering BUCK8 ON/OFF by the hardware. If ENB8 is set to low then you can do on/off. If high, then you cannot change its state by I2C write, which seems to be the case with the Odroids. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* odroid: Update README with USB host usageSuriyan Ramasami2014-11-241-0/+169
| | | | | | | | | Add information wrt using the USB host interface for loading kernel over ethernet and/or usb mass storage. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* arm: odroid: usb: add support for usb host including ethernetSuriyan Ramasami2014-11-175-8/+116
| | | | | | | | | This change adds support for enabling the USB host features of the board. This includes the USB3503A hub and the SMC LAN9730 ethernet controller as well. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* arm: odroid: enable/disable usb host phy for exynos4412Suriyan Ramasami2014-11-172-0/+34
| | | | | | | | Enable/disable the usb host phy on the odroid U/X2 boards which are based on the Exynos4412 SOC. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* arm: odroid: pmic77686: allow buck voltage settingsSuriyan Ramasami2014-11-172-3/+52
| | | | | | | | Allow to set the buck voltage for the max77686. This will be used to reset the SMC LAN9730 ethernet on the odroids. Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* SMDK2410: convert to generic boardDavid Müller (ELSOFT AG)2014-11-171-0/+2
| | | | | | | | Compile-time tested only, as I currently don't have access to the eval board. Signed-off-by: David Müller <d.mueller@elsoft.ch> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos: dts: Correct USB vbus-gpio numbering for SnowSjoerd Simons2014-11-171-2/+2
| | | | | | | | | | | | The current vbus GPIOs on snow make very little sense, their number is far above the maximum. As a result, USB doesn't work on snow. Correct the GPIO numbering so they match the current scheme for exynos5. Tested both EHCI and XHCI to correctly work after this change. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos: Increase command line buffer size (CONFIG_SYS_CBSIZE)Ian Campbell2014-11-171-2/+2
| | | | | | | | | | | I was running into this limit with a not overly long PXE append line. Since the PXE code wants to print the resulting command line increase CONFIG_SYS_PBSIZE too. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Acked-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos5: Use config_distro_bootcmd.hIan Campbell2014-11-175-22/+47
| | | | | | | | | | | | | | | | This replaces the existing CONFIG_BOOTCOMMAND for exynos5250 and 5420. exynos4 platforms seem to have existing complex extra env configuration for booting and so are excluded here. Hence the bootcmd.h is added to exynos5-common.h. I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot tested on arndale. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Guillaume GARDET <guillaume.gardet@free.fr> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* exynos: Enable config_distro_defaults.hIan Campbell2014-11-173-24/+2
| | | | | | | | | | | | | | | ...and remove explicit setting of things which this implies. This is done for all exynos platforms (4 & 5) so it is added to exynos-common.h I'm mainly interested in CONFIG_CMD_BOOTZ and CONFIG_SUPPORT_RAW_INITRD I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot tested on arndale. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Guillaume GARDET <guillaume.gardet@free.fr> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Peach-Pi: Use the enhanced usb_copy() prototypeVadim Bendebury2014-11-171-2/+8
| | | | | | | | | | | | | Exynos5800 IROM has a different, from 5250 and 5420, prototype of the usb_copy() function. Luckily the earlier version did not expect any arguments, which means the same code could be used with old and new SoCs, the old ones just ignoring the arguments. Signed-off-by: Vadim Bendebury <vbendeb@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos5: ddr3: Choose between single or double channel configAkshay Saraswat2014-11-171-0/+10
| | | | | | | | | | | | Add a 4G configuration and choose it based on the number of banks declared in config file. A board with 4 SDRAM banks declared (as per CONFIG_NR_DRAM_BANKS) will end up with the 2G confiuration. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Config: Exynos5420: Refactor SDRAM Bank and SizeAkshay Saraswat2014-11-174-4/+12
| | | | | | | | | | | | | | Since, not every board may have all memory channels configured and all available banks of DMC used, we wish to refactor configs for Memory Bank size and numbers as per board memory config. For Example, Peach-Pit has 2GB memory and will be using only 4 banks but Peach-Pi has 3.5GB memory and will be using all 7 available SDRAM banks. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* DMC: Exynos5: Enable update mode for DREX controllerAlim Akhtar2014-11-172-0/+20
| | | | | | | | | | | | | | | | As per Exynos5800 UM ver 0.00 section 17.13.2.1 CONCONTROL register bit 3 [update_mode], Exynos5800 does not support the PHY initiated update. And it is recommanded to set this field to 1'b1 during initialization. This patch sets this bit. Applying MC-initiated mode makes DDL tracking ON, that helps in compensate MIF voltage variation. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Config: Exynos5800: Enable build for Peach-PiAkshay Saraswat2014-11-177-4/+81
| | | | | | | | | | | | | This adds following things : - New config and defconfig for Peach-Pi board. - Alterations in Kconfig and MAINTAINERS. - Addition of CONFIG_EXYNOS5800. - ADdition of exynos5800-peach-pi in dts list. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos5800: Add DTS for new board Peach-PiAkshay Saraswat2014-11-172-1/+159
| | | | | | | | | | | | We have a new board Peach-Pi similar to Peach-Pit. Peach-Pi differs from Peach-Pit in configuration factors like display resolution, memory size, SoC version etc. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos5800: Introduce new proid for Exynos5800Akshay Saraswat2014-11-175-14/+23
| | | | | | | | | | | | | | This patch intends to add a new proid for Exynos5800 which is a variant of Exynos5420. Product id for Exynos5800 is 0x5422. Both Exynos5420 and Exynos5800 are pin to pin compitable. This gives us an advantage of reusing Exynos5420 clock, pinmux, memory and other settings. Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2014-11-1426-11/+411
|\
| * powerpc/85xx: enable some P1/P2 boards mtdparts for nor flashYangbo Lu2014-11-143-0/+75
| | | | | | | | | | | | | | | | | | | | Enable these boards mtdparts for nor flash: p1020rdb-pd, p1021rdb-pc, p1022ds, p1025twr, and p2020rdb-pc. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Scott Wood <scottwood@freescale.com>
| * keymile/powerpc: move to the architecture-generic board systemValentin Longchamp2014-11-143-0/+9
| | | | | | | | | | | | | | | | | | | | | | This converts all the Keymile powerpc boards to the generic board initialization. This includes the 3 Keymile powerpc subsystems: km82xx, km83xx, and kmp204x. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/mpc83xx: Zero boot_flags arg for calling board_init_f()Valentin Longchamp2014-11-141-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | The argument boot_flags of board_init_f() is not used at all in the powerpc specific board.c init sequence. Now with the generic init sequence, this boot_flags arg is used by board_init_f(). This patch sets the r3 register that is used to pass the boot_flags argument from the start.S board_init_f() call to 0 prior to the function call to avoid unknown content to end up in gd->flags. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/BSC9131RDB: Enable creation of dynamic partitions for NANDAshish Kumar2014-11-142-0/+28
| | | | | | | | | | | | | | | | | | | | * fdt_fixup_mtdparts is called from ft_board_setup * Run "mtdparts default" to create NAND partition on uboot * Use mtdparts to create partitions dynamically rather than using static partitions in device tree Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/BSC9132QDS: Enable creation of dynamic partition for NAND and NORAshish Kumar2014-11-142-0/+33
| | | | | | | | | | | | | | | | | | | | * fdt_fixup_mtdparts is called from ft_board_setup * run "mtdparts default" to create NAND, NOR partition on uboot * Use mtdparts to create partitions dynamically rather than using static partitions in device tree Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/mpc85xx: Use IFC accessor functionPrabhakar Kushwaha2014-11-142-4/+4
| | | | | | | | | | | | | | | | | | | | IFC registers can be of type Little Endian or big Endian depending upon Freescale SoC. Here SoC defines the register type of IFC IP. So use IFC acessor functions instead of in_be32(). Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * t104xrdb: Add Errata A_007662, A_008007 workaround in pbi.cfgPriyanka Jain2014-11-141-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | -A_007662 states that for x1 link width, PCIe2 controller trains in Gen1 speed while configured for Gen2 speed. Workaround:Set the width to x1 and speed to Gen2 by writing to CCSR registers in PBI phase -A_008007 states that PVR register may show random value. Workaround: Reset PVR register using DCSR space in PBI phase Add PBI based software workaround for A_007662 and A_008007 in t104x_pbi.cfg. This is required for SPL-based bootloaders like NAND-boot, SD-boot, SPI-boot Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * powerpc/t4rdb: Add support of CPLDChunhe Lan2014-11-147-0/+229
| | | | | | | | | | | | | | | | | | | | | | This support of CPLD includes - Files and register definitions - Command to switch alternate bank - Command to switch default bank Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * 85xx/b4:Correct USB DR controller liodn entryramneek mehresh2014-11-141-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | LIODN entry for B4860/B4420 mentions USB controller as "mph" insread of "dr". This results in PAMU not permitting bus transactions for USB DR controller on B4860 resulting in USB function failure. Replacing "fsl-usb2-mph" with "fsl-usb2-dr" allows USB DR controller bus transactions Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Reviewed-by: Sethi Varun-B16395 <Varun.Sethi@freescale.com> Reviewed-by: Sun Yusong-R58495 <yorksun@freescale.com>
| * sbc8548: enable and test CONFIG_SYS_GENERIC_BOARDPaul Gortmaker2014-11-141-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tested on the following baseline (note "dirty" since I enabled ALT_BOOT in the config in order to use the alternate boot bank.) Everything seems to work fine with no additional changes. The banner warning message is now gone. --- U-Boot 2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15) CPU: 8548E, Version: 2.1, (0x80390021) Core: e500, Version: 2.2, (0x80210022) Clock Configuration: CPU0:990 MHz, CCB:396 MHz, DDR:198 MHz (396 MT/s data rate), LBC:99 MHz L1: D-cache 32 KiB enabled I-cache 32 KiB enabled I2C: ready DRAM: Detected UDIMM SDRAM: 128 MiB 256 MiB (DDR2, 64-bit, CL=3, ECC off) Flash: 72 MiB L2: 512 KiB enabled *** Warning - bad CRC, using default environment PCI: Host, 64 bit, 66 MHz, sync, arbiter 00:01.0 - 8086:1026 - Network controller PCI1: Bus 00 - 00 PCIe1: Root Complex, x1 gen1, regs @ 0xe000a000 02:00.0 - 1148:9e00 - Network controller PCIe1: Bus 01 - 02 In: serial Out: serial Err: serial Net: eTSEC0 [PRIME], eTSEC1 Hit any key to stop autoboot: 0 => ver U-Boot 2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15) powerpc-linux-gcc (GCC) 4.5.2 GNU ld (GNU Binutils) 2.21 => --- Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * driver/net/fm/memac_phy: set NEG bit for external MDIOsShaohui Xie2014-11-142-1/+5
| | | | | | | | | | | | | | | | | | | | NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure on XAUI PHY, so set this bit definitely to align with the RM. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * Fman/mEMAC: mEMAC fix for 10G MAC and PHYShaohui Xie2014-11-143-3/+12
| | | | | | | | | | | | | | | | | | | | | | | | 1. use Payload length check disable when enable MAC; 2. add XGMII support for setting MAC interface mode; 3. only enable auto negotiation for Non-XGMII mode; 4. return 0xffff if clause 22 is used to read 10G phy_id; Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-By: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * mpc85xx/kmp204x: raise u-boot size to 768KBValentin Longchamp2014-11-141-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Until now this defined to be 512KB and the total binary size actually was on the edge of this limit. Most of the powerpc boards have thus moved to 768KB. Since on the current kmp204x boards there is 1MB reserved for u-boot on the SPI boot flash, there is no problem to set the limit to 768KB as well to be on line with the other powerpc boards and to eventually configure in some additional features (and binary size) to u-boot. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini2014-11-141-0/+9
|\ \
| * | video: speedup writing strings to fb consoleSoeren Moch2014-10-301-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With enabled framebuffer console the printenv command can take several seconds to complete. This patch temporarily disables cache flush when writing strings to fb console. Then there is no noticable delay anymore. Tested with imx6 hdmi framebuffer. Signed-off-by: Soeren Moch <smoch@web.de> Acked-by: Stefano Babic <sbabic@denx.de>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2014-11-1422-22/+1056
|\ \ \ | |_|/ |/| |
| * | arm: mx6: add support for TBS2910 Matrix ARM miniPCSoeren Moch2014-11-137-0/+683
| | | | | | | | | | | | | | | | | | | | | Add initial support for TBS2910 Matrix ARM miniPC. Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC. Signed-off-by: Soeren Moch <smoch@web.de>
| * | mx6sabresd: Staticize when possibleFabio Estevam2014-11-131-6/+6
| | | | | | | | | | | | | | | | | | Annotate 'static' when appropriate for the variables used locally. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6sabresd: Fix error handling in board_mmc_init()Fabio Estevam2014-11-131-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | When an invalid USDHC port is passed we should return -EINVAL instead of 0. Also, return the error immediately on fsl_esdhc_initialize() failure. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | mx6: video_skip: Fix crash on NULL pointerNikolay Dimitrov2014-11-131-1/+5
| | | | | | | | | | | | | | | Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg> Cc: Stefano Babic <sbabic@denx.de>
| * | imx6: SPL support for iMX6 SabreSDJohn Tobias2014-11-131-2/+184
| | | | | | | | | | | | | | | | | | | | | | | | This patch will enable the support for SPL on iMX6 SabreSD. It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6) Signed-off-by: John Tobias <john.tobias.ph@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | imx6: add spl in the header fileJohn Tobias2014-11-131-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | add the spl info in the header file. Also, added a macro statement in m6sabre_common.h to avoid compiler warning. Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
| * | kconfig: imx6: add SUPPORT_SPLJohn Tobias2014-11-131-0/+1
| | | | | | | | | | | | | | | | | | | | | add SUPPORT_SPL feature for iMX6 SabreSD. It need to use mx6sabresd_spl_defconfig to compile it. Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
| * | imx6: add data configuration file for SPLJohn Tobias2014-11-131-0/+58
| | | | | | | | | | | | | | | | | | | | | It's a trim version of mx6q_4x_mt41j128.cfg. It just removed the related settings for DDR Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
| * | imx6: add spl config for mx6sabresdJohn Tobias2014-11-131-0/+5
| | | | | | | | | | | | | | | | | | add a build configuration file for mx6sabresd with spl support Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
| * | imx: mx6q/dlsabreauto: And NAND flash supportYe.Li2014-11-132-0/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The i.MX6Q/DL sabreauto board has one NAND socket, set the CONFIG_NAND_MXS and relevant NAND configurations to enable the MXS NAND flash driver. Add board level codes to set IOMUX and clock for GPMI-NAND and BCH module. Signed-off-by: Ye.Li <B37916@freescale.com> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | imx: mx6q/dl sabre_common: Move MMC ENV offset to 512KB positionYe.Li2014-11-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the CONFIG_ENV_OFFSET from 384KB to 512KB offset, so we will have larger space for u-boot image. When enabling NAND flash support feature, the u-boot image size has exceeded the 384KB, which causes overlay to the environment variables storage. Signed-off-by: Ye.Li <B37916@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | ot1200: fix card detect for usdhc4Christian Gmeiner2014-11-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Today I got the final board and found out that a different connector is used as the one on my development board. The new connector has swaped pins for cd and wp. This change is tested on a production ready board. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * | mx53loco: Change 'fdt_file' dynamicallyFabio Estevam2014-11-132-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since kernel 3.15 there are two dtb's for the imx53-qsb board: imx53-qsb.dtb - For the boards with DA9053 PMIC imx53-qsrb.dtb - For the boards with MC34708 PMIC Change the 'fdt_file' dynamically, so that the correct dtb can be used depending on the board variant. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| * | ot1200: add support for EHCIChristian Gmeiner2014-11-131-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | U-Boot 2014.10-17457-g0b23780-dirty (Nov 10 2014 - 11:41:04) CPU: Freescale i.MX6D rev1.2 at 792 MHz Reset cause: WDOG Board: ot1200 I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB In: serial Out: serial Err: serial Net: using phy at 0 FEC [PRIME] Hit any key to stop autoboot: 0 => usb start (Re)start USB... USB0: Port not available. USB1: USB EHCI 1.00 scanning bus 1 for devices... 4 USB Device(s) found => usb tree USB device tree: 1 Hub (480 Mb/s, 0mA) | u-boot EHCI Host Controller | +-2 Hub (480 Mb/s, 2mA) | +-3 Mass Storage (480 Mb/s, 80mA) | USBest Technology USB Mass Storage Device 0000000000028B | +-4 Vendor specific (480 Mb/s, 2mA) => Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
| * | mx28evk: README: Revision C is also supportedFabio Estevam2014-11-121-1/+1
| | | | | | | | | | | | | | | | | | Adjust the text to mention that rev C of the board is also supported. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * | arm: imx: make bmode command work with SPL/U-Boot comboNikita Kiryanov2014-11-122-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The bmode command forces the SoC to use a specific boot device by writing its boot mode into SRC_GPR9, and notifying the SoC of the change using SRC_GPR10[28] bit: if the bit is on, bootROM uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine the boot device. SPL on the other hand is oblivious to this distinction, so once the bootROM loads SPL from the device configured in SRC_GPR10, SPL will attempt to load U-Boot from the device configured in SRC_SMBR1, which is not updated by the bootROM to the value in SRC_GPR9. The result is that the selected boot device is not used across all the boot stages. Update spl_boot_device() to look at gpr9 when necessary. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefano Babic <sbabic@denx.de> Cc: Troy Kisky <troy.kisky@boundarydevices.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Eric Nelson <eric.nelson@boundarydevices.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Heiko Schocher <hs@denx.de>
OpenPOWER on IntegriCloud