summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* OMAP3: mt_ventoux: sets its own mtdpartsStefano Babic2012-03-271-0/+10
| | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
* OMAP3: mt_ventoux: updated timing for FPGAStefano Babic2012-03-271-6/+5
| | | | | | | Fix chipselect timing for FPGA Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
* twl4030: fix potential power supply handling issuesGrazvydas Ignotas2012-03-271-4/+14
| | | | | | | | | | | | | | twl4030_pmrecv_vsel_cfg currently first sets up device group (effectively enabling the supply), and only then sets vsel (selects voltage). This could lead to wrong voltage for a short time, or even long time if second i2c write fails. Fix this by writing vsel first and device group after that. Also introduce error checking to not enable the supply if we failed to set the voltage, and start logging errors as power supply problems are usually important. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
* NAND: TI: fix warnings in omap_gpmc.cStefano Babic2012-03-271-6/+8
| | | | | | | | | | | | | | The following warnings are reported for boards using SOFT ECC. omap_gpmc.c:33:30: warning: 'hw_nand_oob' defined but not used omap_gpmc.c:78:13: warning: 'omap_hwecc_init' defined but not used omap_gpmc.c:116:12: warning: 'omap_correct_data' defined but not used omap_gpmc.c:182:12: warning: 'omap_calculate_ecc' defined but not used omap_gpmc.c:208:13: warning: 'omap_enable_hwecc' defined but not used Signed-off-by: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Scott Wood <scottwood@freescale.com>
* cam_enc_4xx: Rename 'images' to 'imgs'Tom Rini2012-03-271-24/+24
| | | | | | | | | | | To avoid a conflict with common/cmd_bootm.c's 'images' (which is exposed as part of the Linux SPL series), rename the board-specific 'images' to 'imgs'. Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Heiko Schocher <hs@denx.de>
* arm: Add Prep subcommand support to bootmSimon Schwarz2012-03-272-169/+206
| | | | | | | | | | | | | Adds prep subcommand to bootm implementation of ARM. When bootm is called with the subcommand prep the function stops right after ATAGS creation and before announce_and_cleanup. This is used in command "cmd_spl export" Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: twister: add support to boot Linux from SPLStefano Babic2012-03-272-0/+35
| | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* SPL: call cleanup_before_linux() before booting LinuxStefano Babic2012-03-271-1/+1
| | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* OMAP3: SPL: do not call I2C init if no I2C is set.Stefano Babic2012-03-271-0/+2
| | | | | | | | | | Call i2c initialization in spl_board_init only if I2C is configured for the board. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* Add cache functions to SPL for armv7Stefano Babic2012-03-273-4/+5
| | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de> CC: Simon Schwarz <simonschwarzcor@gmail.com>
* devkit8000: Implement and activate direct OS bootSimon Schwarz2012-03-272-2/+23
| | | | | | | | | | - Implements spl_start_uboot() for devkit8000 - Add configs to activate direct OS boot from SPL Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* omap/spl: change output of spl_parse_image_headerSimon Schwarz2012-03-271-1/+1
| | | | | | | | | This only outputs "Assuming u-boot.bin..." if debug is active. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* omap-common/spl: Add linux boot to SPLSimon Schwarz2012-03-273-23/+75
| | | | | | | | | | | | | | | | | | | | | | | | This adds Linux booting to the SPL This depends on CONFIG_MACH_TYPE patch by Igor Grinberg (http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809) Related CONFIGs: CONFIG_SPL_OS_BOOT Activates/Deactivates the OS booting feature CONFIG_SPL_OS_BOOT_KEY defines the IO-pin number u-boot switch - if pressed u-boot is booted CONFIG_SYS_NAND_SPL_KERNEL_OFFS Offset in NAND of direct boot kernel image to use in SPL CONFIG_SYS_SPL_ARGS_ADDR Address where the kernel boot arguments are expected - this is normaly RAM-begin + 0x100 Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* devkit8000/spl: init GPMC for dm9000 in SPLSimon Schwarz2012-03-272-0/+20
| | | | | | | | | Linux crashes if the GPMC isn't configured for the dm9000. Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* omap-common: Add NAND SPL linux bootingSimon Schwarz2012-03-271-16/+50
| | | | | | | | | | | | | | | | This implements booting of Linux from NAND in SPL Related config parameters: CONFIG_SYS_NAND_SPL_KERNEL_OFFS Offset in NAND of direct boot kernel image to use in SPL CONFIG_SYS_SPL_ARGS_ADDR Address where the kernel boot arguments are expected - this is normally RAM-start + 0x100 (on ARM) Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* devkit8000: add config for spl commandSimon Schwarz2012-03-271-0/+8
| | | | | | | | | This adds some configs for devkit8000 to use the new spl command Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> CC: Tom Rini <tom.rini@gmail.com> CC: Stefano Babic <sbabic@denx.de> CC: Wolfgang Denk <wd@denx.de>
* Add cmd_spl commandSimon Schwarz2012-03-275-0/+253
| | | | | | | | | | | | | | | This adds a spl command to the u-boot. Related config: CONFIG_CMD_SPL activate/deactivate the command CONFIG_CMD_SPL_NAND_OFS Offset in NAND to use Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com> Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Tom Rini <tom.rini@gmail.com> CC: Wolfgang Denk <wd@denx.de>
* mx53ard: Initialize return code with errorFabio Estevam2012-03-271-1/+1
| | | | | | | | | The variable "rc" is the return of board_eth_init() function. Initialize it with an error code, so that this function can return an error when CONFIG_SMC911X is not set. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx53: Make PLL2 to be the parent of UART clockFabio Estevam2012-03-271-3/+17
| | | | | | | | | | | | | | | | | | Change the parent UART clock to be PLL2, so that U-boot can also boot a Freescale 2.6.35 kernel for mx53. FSL kernel and U-boot changed the UART parent from PLL3 to PLL2 to avoid conflicts with IPU clocks, so that the video resolution can be changed without affecting the UART clock. On a 2.6.35 kernel the serial console is messed up after IPU driver is loaded and this patch fixes this problem. Tested on a mx53loco board booting a FSL kernel and also a mainline kernel. Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
* configs: imx: Use CONFIG_SF_DEFAULT_CSFabio Estevam2012-03-273-3/+3
| | | | | | | | | | CONFIG_SPI_FLASH_CS is not used anywhere. Use CONFIG_SF_DEFAULT_CS instead. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* mx28evk: Provide default values for SPI bus and chip selectFabio Estevam2012-03-271-0/+2
| | | | | | | | | | Provide default values for SPI bus and chip select. This allows the command "sf probe" to work without passing SPI bus and chip select numbers as arguments. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
* USB: ehci-mx6: Add proper IO accessorsFabio Estevam2012-03-271-9/+4
| | | | | | | | | Add proper IO accessors for mx6 usb registers. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
* mx6: Read silicon revision from registerFabio Estevam2012-03-273-3/+171
| | | | | | | | | | | | | | | Instead of hardcoding the mx6 silicon revision, read it in run-time. Also, besides the silicon version print the mx6 variant type: quad,dual/solo or solo-lite. Tested on a mx6qsabrelite, where it shows: CPU: Freescale i.MX6Q rev1.0 at 792 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Jason Liu <r64343@freescale.com>
* i.MX28: Drop __naked function from spl_mem_initMarek Vasut2012-03-271-7/+3
| | | | | | | | | | | | | Instead of compiling the function and using the result as a constant, simply use the constant. NOTE: This patch works around bug: http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546 Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
* mxs_spi: Return proper timeout errorFabio Estevam2012-03-271-3/+3
| | | | | | | Instead of returning -1, it is preferred to return -ETIMEDOUT in case of timeouts. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
* i.MX28: Make the stabilization delays shorterMarek Vasut2012-03-271-4/+4
| | | | | | | | | | | | | Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be enough according to the datasheet and bootlets. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Robert Deliën <robert@delien.nl> Cc: Fabio Estevam <festevam@gmail.com> Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
* pmic_i2c: Return error in case of invalid pmic_i2c_tx_numFabio Estevam2012-03-271-0/+6
| | | | | | | | | Return error in case of invalid pmic_i2c_tx_num. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Stefano Babic <sbabic@denx.de>
* mx6: Remove duplicate definition of ANATOP_BASE_ADDRFabio Estevam2012-03-271-1/+0
| | | | | | Remove duplicate definition of ANATOP_BASE_ADDR. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx6: Fix reset cause for Power On Reset caseFabio Estevam2012-03-271-0/+1
| | | | | | | | | | | | | After booting mx6qsabrelite from POR the following is reported: CPU: Freescale i.MX61 family rev1.0 at 792 MHz Reset cause: unknown reset This is because both the POR and WDOG bits are set after reset. Fix this by also checking both bits in the POR case. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITEEric Nelson2012-03-271-0/+2
| | | | | | Allow non-dt kernels to boot Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
* i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAGEric Nelson2012-03-272-0/+6
| | | | | | | | | | | | | | This is needed to support Freescale-supplied userspaces. At the moment, both the IPU and VPU libraries provided by Freescale in the "imx-lib" package contain routines which scrape the system revision from /proc/cpuinfo. In the VPU library, this information is used to load the proper firmware, allowing a single binary to be used across various i.MX processors. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Stefano Babic <sbabic@denx.de>
* i.MX28: Enable additional DRAM address bitsMarek Vasut2012-03-271-1/+1
| | | | | | | | Enables all fourteen address lines for DRAM Signed-off-by: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Marek Vasut <marek.vasut@gmail.com>
* mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use ↵Eric Nelson2012-03-271-4/+4
| | | | | | for environment Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* mx31: add "ARM11P power gating" to get_reset_causeHelmut Raiger2012-03-271-0/+2
| | | | | | Add missing reset reason 7 to get_reset_cause(). Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
* mx31pdk: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-271-1/+1
| | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* efikamx: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-271-1/+1
| | | | | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Cc: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Marek Vasut <marek.vasut@gmail.com>
* mx53smd: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-271-1/+1
| | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx53evk: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-271-1/+1
| | | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Cc: Jason Liu <r64343@freescale.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* mx51evk: Fix CONFIG_SYS_MEMTEST_ENDFabio Estevam2012-03-271-1/+1
| | | | | | CONFIG_SYS_MEMTEST_END should be higher than CONFIG_SYS_MEMTEST_START. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* i.MX6: mx6qsabrelite: add ext2 supportEric Nelson2012-03-271-0/+1
| | | | | | Current Ubuntu releases from Freescale contain a boot script in ext3 filesystem. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
* imximage: Remove overwriting of flash_offsetDirk Behme2012-03-272-4/+15
| | | | | | | | | | | | | | | | | | | | The flash header supports different flash offsets for different boot devices. E.g. parallel NOR or OneNAND use a different offset than FLASH_OFFSET_STANDARD (== 0x400). The flash offset is correctly read from the configuration in parse_cfg_cmd(). But is then overwritten wrongly in set_imx_hdr_v1/2(). Fix this by removing this overwriting. Use the flash offset correctly read from the configuration, instead. If there is no flash_offset read from the configuration file, i.e. the BOOT_FROM tag is missing, exit with an error message. Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Jason Liu <liu.h.jason@gmail.com> CC: Stefano Babic <sbabic@denx.de> Tested-by: Stefano Babic <sbabic@denx.de>
* IXP: Fix GPIO_INT_ACT_LOW_SET()Marek Vasut2012-03-261-2/+8
| | | | | | | | | The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7. This is due to the fact that there are two registers for total of 16 lines. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* IXP: Fix NAND build warning on PDNB3 and SCPUMarek Vasut2012-03-261-13/+3
| | | | | | | | | | | | | | nand.c: In function ‘pdnb3_nand_read_buf’: nand.c:107:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing] nand.c: In function ‘pdnb3_nand_dev_ready’: nand.c:124:18: warning: variable ‘val’ set but not used [-Wunused-but-set-variable] Remove the 4-byte-at-time read mode altogether, the most is bogus and will likely cause unaligned accesses. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* IXP: Move PDNB3 and SCPU from Makefile to boards.cfgMarek Vasut2012-03-262-12/+2
| | | | | | Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* IXP: Squash warnings in IXP NPEMarek Vasut2012-03-263-7/+1
| | | | | | | | | | | | | IxEthAcc.c: In function ‘ixEthAccInit’: IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare] IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’: IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable] IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’: IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}Marek Vasut2012-03-2612-13/+12
| | | | | | | | | These symbols are no longer defined in Linux-ARM's mach-types files. Replace these with CONFIG_MACH_TYPE instead. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* IXP: Make IXP buildable with arm-linux- toolchainsMarek Vasut2012-03-261-0/+3
| | | | | | | | | | | Add -EB flag to LD to switch endianness of the linker. This should make armeb targets buildable again. Also, make use of U-Boot's internal libgcc instead of toolchain's one, this works around the use of libraries from GCC, which might be little endian. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* Examples: Properly append LDFLAGS to LD commandMarek Vasut2012-03-261-1/+1
| | | | | | | | | The LD command in examples/standalone/Makefile ignored platform specific LDFLAGS setup. Pass these LDFLAGS to the command. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Bryan Hundven <bryanhundven@gmail.com> Cc: Michael Schwingen <rincewind@discworld.dascon.de>
* SPL: Enable YMODEM support on BeagleBone and AM335x EVMMatt Porter2012-03-261-0/+1
| | | | | | Cc: Chandan Nath <chandan.nath@ti.com> Tested-by: Tom Rini <trini@ti.com> Signed-off-by: Matt Porter <mporter@ti.com>
* SPL: Add YMODEM over UART load supportMatt Porter2012-03-266-0/+93
| | | | | | | | | | Adds support for loading U-Boot from UART using YMODEM protocol. If YMODEM support is enabled in SPL and the romcode indicates that SPL loaded via UART then SPL will wait for start of a YMODEM transfer via the console port. Signed-off-by: Matt Porter <mporter@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
OpenPOWER on IntegriCloud