summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2016-01-2779-502/+1630
|\
| * armv8/ls1043aqds: add QSPI boot supportQianyu Gong2016-01-277-7/+35
| | | | | | | | | | | | | | Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: add QSPI support in SD bootGong Qianyu2016-01-277-0/+69
| | | | | | | | | | | | | | | | | | QSPI and IFC are pin-multiplexed on LS1043A. So we use ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: add DSPI supportGong Qianyu2016-01-276-10/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable three DSPI flash memories on board. Commands: => sf probe 1:0 SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB => sf probe 1:1 SF: Detected SST25WF040B with page size 256 Bytes, erase size 4 KiB, total 512 KiB => sf probe 1:2 SF: Detected EN25S64 with page size 256 Bytes, erase size 64 KiB, total 8 MiB Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * dm: env_sf: fix saveenv() to use driver modelGong Qianyu2016-01-271-0/+29
| | | | | | | | | | | | | | | | | | | | It might be missed when converting spi_flash_probe() in cmd_sf.c. This patch refers to commit fbb099183e3a ("dm: Convert spi_flash_probe() and 'sf probe' to use driver model"). Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * spi: fsl_qspi: Fix qspi_op_rdsr memcpy issueGong Qianyu2016-01-271-3/+3
| | | | | | | | | | | | | | | | | | | | In current driver, we always copy 4 bytes to the dest memory. Actually the dest memory may be shorter than 4 bytes. Add an argument to indicate the dest memory length. Avoid writing memory outside of the bounds. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * spi: fsl_qspi: Fix qspi_op_rdid memcpy issueGong Qianyu2016-01-271-6/+6
| | | | | | | | | | | | | | | | | | | | | | In current driver everytime we memcpy 4 bytes to the dest memory regardless of the remaining length. This patch adds checking the remaining length before memcpy. If the length is shorter than 4 bytes, memcpy the actual length of data to the dest memory. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * spi: fsl_qspi: fix compile warning for 64-bit platformGong Qianyu2016-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following compile warning: drivers/spi/fsl_qspi.c: In function 'fsl_qspi_probe': drivers/spi/fsl_qspi.c:937:15: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] priv->regs = (struct fsl_qspi_regs *)plat->reg_base; ^ Just make the cast explicit. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * mmc: fsl_esdhc: set Abort command type for CMD12Yangbo Lu2016-01-271-4/+1
| | | | | | | | | | | | | | | | | | According to SD spec, CMD12, CMD52 for writing I/O abort in CCCR need to be set an Abort command type when they are sent. So, we remove all chip-specific #ifdefs and make it available for all platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: Add lpuart supportWenbin Song2016-01-276-0/+90
| | | | | | | | | | | | | | | | Add lpuart support using the driver model. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: Spilt off board device treeWenbin Song2016-01-274-3/+18
| | | | | | | | | | | | | | | | Move new /chosen node out of the board device tree. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: Select lpuart pins of various muxesShaohui Xie2016-01-271-0/+13
| | | | | | | | | | | | | | | | | | | | Set Board Configuration Register to select the lpuart pins of various muxes. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * mmc: fsl_esdhc: increase data transaction timeout to 500msYangbo Lu2016-01-271-1/+8
| | | | | | | | | | | | | | | | | | | | The MMC spec says "It is strongly recommended for hosts to implement more than 500ms timeout value even if the card indicates the 250ms maximum busy length." Even the previous value of 300ms is known to be insufficient for some cards. So, increase the timeout to 500ms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: fsl-mc: Remove portal id hard-codingPrabhakar Kushwaha2016-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Management Complex firmware 9.0 has fixed the issue of dprc_destroy_container i.e. the used portal is not return to the free pool. Which was resulting in error ethernet driver want to use this portal via either DPL or dynamically in Linux. Hard-coding of portal id is removed. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: ldpaa: Add debug info of printing DPMAC statsPrabhakar Kushwaha2016-01-271-0/+78
| | | | | | | | | | | | | | | | | | | | | | | | Add debug information prints to provide DPMAC statistics - Number of bytes received - Number of received and discard frames - Number of bytes transferred - Number of frames transferred etc. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: ldpaa: Increase num of buffers for a poolPrabhakar Kushwaha2016-01-271-1/+1
| | | | | | | | | | | | | | | | | | | | Management Complex FW 9.0 set the hardware depletion to be 20 buffers in order to support multiple pools in DPNI. This requires driver to fill the pool with at least 21 to be able to receive frames. So, Increase number of buffers for a pool. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: ldpaa: Report back only error frames for txPrabhakar Kushwaha2016-01-271-0/+12
| | | | | | | | | | | | | | | | | | | | | | Management Complex FW 9.0 puts a new requirement to provide Tx confirmation and error queue configuration by calling dpni_set_tx_conf API. Configure report of only error frames for a tx frame. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: fsl-mc: Prepare extended cfg for DPNI createPrabhakar Kushwaha2016-01-271-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | Management Complex FW 9.0 puts a new requirement to prepare extended parameters which should be provided as input in dpni_create. extended parameters includes traffic class and IP reassembly configurations. So prepare extended parameters with default "0" as input for dpni_create. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: fsl-mc: flib changes for MC FW 9.0.0Prabhakar Kushwaha2016-01-279-169/+565
| | | | | | | | | | | | | | | | | | | | | | | | | | MC firmware version 9.0.0 contains - Support of new APIs - Update in existing APIs - Change in Major and minor version of DPAA2 objects This patch contains modifications in FLIB files to support new MC firmware version. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver: net: fsl-mc: Add version check for MC objectsPrabhakar Kushwaha2016-01-272-1/+78
| | | | | | | | | | | | | | | | Check and compare version of management complex's object with the version supported by Freescale ldpaa2 ethernet driver. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: change error handler for esbc_validateAneesh Bansal2016-01-272-1/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | In case of error while executing esbc_validate command, SNVS transition and issue of reset is required only for secure-boot. If boot mode is non-secure, this is not required. Similarly, esbc_halt command which puts the core in Spin Loop is applicable only for Secure Boot. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: enable chain of trust for PowerPC platformsAneesh Bansal2016-01-272-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Chain of Trust is enabled for PowerPC platforms for Secure Boot. CONFIG_BOARD_LATE_INIT is defined. In board_late_init(), fsl_setenv_chain_of_trust() is called which will perform the following: - If boot mode is non-secure, return (No Change) - If boot mode is secure, set the following environmet variables: bootdelay = 0 (To disable Boot Prompt) bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script) Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: enable chain of trust for ARM platformsAneesh Bansal2016-01-276-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Chain of Trust is enabled for ARM platforms (LS1021 and LS1043). In board_late_init(), fsl_setenv_chain_of_trust() is called which will perform the following: - If boot mode is non-secure, return (No Change) - If boot mode is secure, set the following environmet variables: bootdelay = 0 (To disable Boot Prompt) bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script) Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: create function to determine boot modeAneesh Bansal2016-01-274-0/+61
| | | | | | | | | | | | | | | | | | A function is created to detrmine if the boot mode is secure or non-secure for differnt SoC's. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: split the secure boot functionality in two partsAneesh Bansal2016-01-273-55/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two phases in Secure Boot 1. ISBC: In BootROM, validate the BootLoader (U-Boot). 2. ESBC: In U-Boot, continuing the Chain of Trust by validating and booting LINUX. For ESBC phase, there is no difference in SoC's based on ARM or PowerPC cores. But the exit conditions after ISBC phase i.e. entry conditions for U-Boot are different for ARM and PowerPC. PowerPC: If Secure Boot is executed, a separate U-Boot target is required which must be compiled with a diffrent Text Base as compared to Non-Secure Boot. There are some LAW and TLB settings which are required specifically for Secure Boot scenario. ARM: ARM based SoC's have a fixed memory map and exit conditions from BootROM are same irrespective of boot mode (Secure or Non-Secure). Thus the current Secure Boot functionlity has been split into two parts: CONFIG_CHAIN_OF_TRUST This will have the following functionality as part of U-Boot: 1. Enable commands like esbc_validate, esbc_halt 2. Change the environment settings based on bootmode, determined at run time: - If bootmode is non-secure, no change - If bootmode is secure, set the following: - bootdelay = 0 (Don't give boot prompt) - bootcmd = Validate and execute the bootscript. CONFIG_SECURE_BOOT This is defined only for creating a different compile time target for secure boot. Traditionally, both these functionalities were defined under CONFIG_SECURE_BOOT. This patch is aimed at removing the requirement for a separate Secure Boot target for ARM based SoC's. CONFIG_CHAIN_OF_TRUST will be defined and boot mode will be determine at run time. Another Security Requirement for running CHAIN_OF_TRUST is that U-Boot environemnt must not be picked from flash/external memory. This cannot be done based on bootmode at run time in current U-Boot architecture. Once this dependency is resolved, no separate SECURE_BOOT target will be required for ARM based SoC's. Currently, the only code under CONFIG_SECURE_BOOT for ARM SoC's is defining CONFIG_ENV_IS_NOWHERE Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: include/configs: move definition of CONFIG_CMD_BLOBAneesh Bansal2016-01-2718-71/+2
| | | | | | | | | | | | | | | | | | | | CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was earlier defined in all config files. The definition has been moved to a common file which is included by all configs. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * secure_boot: include/configs: make secure boot header file uniformAneesh Bansal2016-01-2713-16/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The file fsl_secure_boot.h must be included in config file for Secure Boot. This is not required to be protected by any macro. CONFIG_FSL_CAAM must be defined and CONFIG_CMD_HASH should be turned on. The above was missing in some config files and all files have been made uniform in this respect. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * drivers: net: fsl_mc: Compare pointer value qbman_swp_mc_startPratiyush Mohan Srivastava2016-01-251-1/+3
| | | | | | | | | | | | | | | | | | | | Current code compares the return pointer of function qbman_cena_write_start with NULL. Instead the value of the return pointer should be compared. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls2080a: Increase MC's DDR size to 512 MBPratiyush Mohan Srivastava2016-01-251-1/+1
| | | | | | | | | | | | | | | | | | Freescale's management complex (MC) uses System DDR for internal usage. Increase used System DDR size from 256MB to 512 MB. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls2040a: Add support of LS2040A SoCPratiyush Mohan Srivastava2016-01-252-0/+2
| | | | | | | | | | | | | | | | | | Freescale's LS2040A is a another personality of LS2080A SoC without AIOP support consisting of 4 armv8 cores. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: Enable all 8 DPMAC ports in LS2080A PersonalityPratiyush Mohan Srivastava2016-01-251-5/+0
| | | | | | | | | | | | | | | | | | | | LS2080A has support for 8 DPMAC ports out of which only 5 ports can be used at a time. Enabling all 8 DPMAC ports of LS2080A personality. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com> Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * SECURE BOOT: support for validation of dynamic imageAneesh Bansal2016-01-253-18/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some images to be validated are relocated to a dynamic address at run time. So, these addresses cannot be known befor hand while signing the images and creating the header offline. So, support is required to pass the image address to the validate function as an argument. If an address is provided to the function, the address field in Header is not read and is treated as a reserved field. Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * SECURE BOOT: separate function created for signatureAneesh Bansal2016-01-251-44/+54
| | | | | | | | | | | | | | | | | | | | | | The code for image hash calculation, hash calculation from RSA signature and comparison of hashes has been mobed to a separate function. Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * SECURE BOOT: separate functions for reading keysAneesh Bansal2016-01-251-73/+96
| | | | | | | | | | | | | | | | | | | | | | | | | | Separate functions are created for reading and checking the sanity of Public keys: - read_validate_single_key - read_validate_ie_tbl - read_validate_srk_table Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * SECURE BOOT: change prototype of fsl_secboot_validate functionAneesh Bansal2016-01-253-15/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The prototype and defination of function fsl_secboot_validate has been changed to support calling this function from another function within u-boot. Only two aruments needed: 1) header address - Mandatory 2) SHA256 string - optional Signed-off-by: Saksham Jain <saksham@freescale.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * drivers/ddr/fsl: fsl_ddr_sdram_size remove unused controllersEd Swarthout2016-01-251-0/+1
| | | | | | | | | | | | | | | | Following commit 61bd2f75, exclude unused DDR controller from calculating RAM size for SPL boot. Signed-off-by: Ed Swarthout <Ed.Swarthout@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-layerscape: fixes lsch2 serdes registers defineShaohui Xie2016-01-251-20/+47
| | | | | | | | | | | | | | Fixes lsch2 SerDes registers define according to LS1043A RM Rev D. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * arm: ls1021a: Adjust sata register default valuesTang Yuantian2016-01-251-5/+5
| | | | | | | | | | | | | | | | Updated the default sata register values to enhance the performance and stability. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * driver/ddr/fsl: Add workaround for A009663Shengzhou Liu2016-01-256-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0 before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE] to the desired value after DDR initialization has completed. When DDR controller is configured to operate in auto-precharge mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: fsl-lsch3: fixup SYSCLK frequency in device treePrabhakar Kushwaha2016-01-251-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | SYSCLK frequency is dependent on on-board switch settings. It may vary as per requirement. boot-loader is aware of board switch configurations. So Fixup Linux device tree from boot-loader. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> CC: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: enable qixis_reset command to boot from NAND/SDGong Qianyu2016-01-251-0/+4
| | | | | | | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: fix qixis_reset command issueGong Qianyu2016-01-251-1/+1
| | | | | | | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * freescale/qixis: Add support for booting from SD/QSPIGong Qianyu2016-01-251-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1.Use "qixis_reset sd" to boot from SD 2.Use "qixis_reset sd_qspi" to boot from SD with QSPI support 3.Use "qixis_reset qspi" to boot from QSPI flash On some SoCs such as LS1021A and LS1043A, IFC and QSPI could be pin-multiplexed. So the switches are different between SD boot with IFC support and SD boot with QSPI support. The default booting from SD is with IFC support. Once QSPI is enabled(IFC disabled), only use I2C to access QIXIS. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: Add support for >2GB memoryShaohui Xie2016-01-253-4/+27
| | | | | | | | | | | | | | This patch also exposes the complete DDR region(s) to Linux. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * fsl/ddr: Add workaround for ERRATUM_A009942Shengzhou Liu2016-01-252-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | During the receive data training, the DDRC may complete on a non-optimal setting that could lead to data corruption or initialization failure. Workaround: before setting MEM_EN, set DEBUG_29 register with specific value for different data rates. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2016-01-27108-1263/+1164
|\ \
| * | ppc: xilinx-ppc440-generic: Wire LL_TEMAC driverRicardo Ribalda Delgado2016-01-274-6/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the xparameters file contains a LL_TEMAC definition compile its driver and the net commands. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
| * | net: xilinx_ll_temac: Fix string overflowRicardo Ribalda Delgado2016-01-271-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Size of this snprintf "lltemac.%lx" is bigger than 16 characters. Replacing it with "ll_tem.%lx" Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
| * | ppc: xilinx_ppc440_generic: Remove uncalled functionsRicardo Ribalda Delgado2016-01-271-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not set. Remove unused function. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
| * | ppc: xilinx_ppc405_generic: Remove uncalled functionsRicardo Ribalda Delgado2016-01-271-5/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not set. Remove unused function. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
OpenPOWER on IntegriCloud