summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* SPEAr: Enable dcache for fast file transferShiraz Hashim2012-07-071-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable data cache with 1:1 mapping of DDR to enable fast file transfer over tty which was doing lot of copy. This feature is enabled only for flashing operation i.e. when CONFIG_SPEAR_USBTTY is enabled. This has been tested on SPEAr320, SPEAr600 and SPEAr900 evaluation boards. Following figures show an estimate on the performance improvements. The test setup was a Linux host (not Windows) and involved measurement of only binary transfer time, through kermit. The flash erase and flash copy time would be unaffected by these patches. Another thing is this that the timings remained more or less same across ARM9 and Cortex based devices, hence reporting only one of the cases. Before Enhancements =================== $ time ukermit.small -p /dev/ttyACM0 -f spear320_uImage.img Downloading file: 100.00% completed(2014080/2014080 bytes) real 0m41.228s user 0m0.002s sys 0m0.064s After Enhancements ================== $ time ukermit.large -p /dev/ttyACM0 -f spear320_uImage.img Downloading file: 100.00% completed(2014080/2014080 bytes) real 0m5.441s user 0m0.001s sys 0m0.001s Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Enable autoneg for ethernetShiraz Hashim2012-07-071-0/+1
| | | | | | | | | | | | | | | | Enabling autoneg avoids situation on few phys with fixed configuration. For example, in one situation, nfs boot timed out when phy configuration is 100Mbps. In another situtation, when traffic is directed to SPEAr, either thru cross-cable or thru switch, the TFTP or DHCP command in u-boot starts to timeout very often. When Autoneg is ON, same phys started working perfectly. Reported-by: Deepak Sikri <deepak.sikri@st.com> Reported-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Enable udc and usb-console support only for usbtty configurationVipin KUMAR2012-07-071-0/+3
| | | | | | | | | | This patch enables the UDC and usb-console support only for usbtty configurations Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Enable usb device high speed supportVipin KUMAR2012-07-071-0/+1
| | | | | | | | This patch enables the support for usb high speed device for spear platform SOCs Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Initialize SNOR in early_board_init_fAmit Virdi2012-07-072-0/+9
| | | | | | | | | | flash reading is required earlier than flash_init is called since the env_init is called before flash_init. This makes the smi_init necessary before env_init being called. Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Change the default environment variablesVipin KUMAR2012-07-073-9/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch modifies the default environment variables as: 1. Default bootargs: - console=ttyAMA0,115200 - For environment present in NOR flash root=/dev/mtdblock3 - For environment present in NAND flash root=/dev/mtdblock7 - Removes "mem=" option 2. Introduces CONFIG_EXTRA_ENV_USBTTY as default usbtty env var even when usbtty is not selected 3. Add default definitions for nfsboot and ramboot 4. Add a new default environment variable(CONFIG_EXTRA_ENV_UNLOCK) for SPEAr310 and SPEAr320 Signifacance of CONFIG_EXTRA_ENV_USBTTY: This environment variable is important for flashing utility to work. So if somebody accidently erases the env sector then also this variable must be preserved so that flashing utility functions properly. Signifacance of CONFIG_EXTRA_ENV_UNLOCK: This env variable is read by the cfi driver to unlock all flash sectors. This is necessary because the Parallel NOR flash connected on the spear310 and spear320 boards, M28W64, has all its sectors in locked state at reset and these have to be unlocked explicitly before being erased or written. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)Vipin KUMAR2012-07-071-1/+0
| | | | | | | | | SPEAr doesn't need CONFIG_SYS_HZ_CLOCK. This commit removes it. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Add configuration options for spear3xx and spear6xx boardsVipin KUMAR2012-07-079-186/+77
| | | | | | | | | | | | | | | | | This patch adds options for all the below mentioned configurations and subsequently renames the include/configs/spearxxx.h files to spear3xx_evb.h, spear6xx_evb.h etc to depict evaluation board configuration. SPEAr3xx and SPEAr6xx boards can be compiled in following configurations 1. Environment placed in NAND 2. Console on usb device 3. Console on usb device with environment placed in NAND 4. SPEAr310 and SPEAr320 support environment variables in parallel NOR flash. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Add basic arch related support for SPEAr SoCsVipin KUMAR2012-07-074-1/+93
| | | | | | | | | | | Earlier, architecture specific init code was mixed with board initialization code in board/spear/... This patch updates architecture support for SPEAr in latest u-boot and prints the SoC information. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Add interface information in initializationVipin Kumar2012-07-077-22/+61
| | | | | | | | | | Few Designware peripheral registers need to be modified based on the ethernet interface selected by the board. This patch supports interface information in ethernet driver Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Add macb driver support for spear310 and spear320Vipin KUMAR2012-07-075-6/+78
| | | | | | | | | | | SPEAr310 and SPEAr320 SoCs have an extra ethernet controller. The driver for this device is already supported by u-boot, so configuring board configuration file and defining base addresses etc to make use of the common driver Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Configure network support for spear SoCsVipin KUMAR2012-07-077-2/+56
| | | | | | Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Place ethaddr write and read within CONFIG_CMD_NETVipin KUMAR2012-07-072-8/+29
| | | | | | | | | | ethaddr can be optionally read from i2c memory. So, chip_config command supports reading/writing hw mac id into i2c memory. Placing this code within CONFIG_CMD_NET as this would only be needed when network interface is configured Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Eliminate dependency on Xloader tableAmit Virdi2012-07-073-115/+0
| | | | | | | | | | Xloader table was used primarily to inform u-boot about the DDR size. However, now the ddr size is calculated at runtime which eliminates any need for the Xloader table. So removing this unnecessary code. Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* SPEAr: Fix ARM relocation supportAmit Virdi2012-07-071-19/+1
| | | | | | | | | | | | | | | While the u-boot code is running from the flash, it is essential that no access is made to the bss segment. This is due to the fact that .rel.dyn and .bss areas overlap and former contains information used in relocation. In SPEAr, this was not taken into consideration. As a result, while the relocation wasn't complete, dram_init populated an uninitialized global variable resulting in corruption of .rel.dyn area, which resulted in u-boot crash. This commit fixes this problem by removing code that accesses bss segment Signed-off-by: Amit Virdi <amit.virdi@st.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fixed page size for Winbond W25Q128FV flashArmando Visconti2012-07-071-1/+1
| | | | | | Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change timeout loop implementationAmit Virdi2012-07-071-10/+17
| | | | | | | | | | | There are two problems in the current timeout loop implementation: 1. In case initial test failing, there will always be a delay of 1 ms 2. The delay duration is not tunable The new implementation addresses both these limitations. Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fix bug in flash_print_info()Armando Visconti2012-07-071-2/+7
| | | | | | | | | If the flash size was smaller than 1MB then flash_print_info() was erroneously reporting 0 MB. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change the flash probing methodArmando Visconti2012-07-071-27/+65
| | | | | | | | | | THis patch introduces a new methodology for flash probing in which flash_devices[] table, looked-up thru the dev_id, is used to locate the flash geometry and information. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Removed no needed dependency on ST_M25Pxx_IDArmando Visconti2012-07-071-32/+18
| | | | | | | | | | Since the smi erase code is very generic and works for any kind of flash, there is no need to test for ST_M25Pxx_ID flash types like m25p40 flashes). Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Fix smi read statusVipin Kumar2012-07-071-6/+2
| | | | | | | | | | | | smi_read_sr fails sometimes because of TFF not getting set within assumed time. This condition may arise because of, for example, smi memory being in a erase mode. This fix is to enable reading the status register until timeout. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Move status register read before modifying ctrl registerShiraz Hashim2012-07-071-2/+4
| | | | | | Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Read status until timeout happensVipin KUMAR2012-07-071-1/+1
| | | | | | | | | SMI driver read status fails because the control register could not be overwritten. Instead, the read status should be tried until timeout. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Enhance the error handlingAmit Virdi2012-07-071-13/+21
| | | | | | | | | | | This commit does the following: - Reports error if SNOR flash is not found on the board - Changes smi_read_sr to return error using which a retry mechanism is implemented for reading flash status Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Change SMI timeout valuesAmit Virdi2012-07-071-2/+2
| | | | | Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Return error in case TFF is not setAmit Virdi2012-07-071-8/+14
| | | | | | | | | | Curently the code makes wrong assumption that the Transfer finished flag shall be set within the stipulated time. However, there may occur a scenario in which the TFF flag is not set. Return error in that case. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* st_smi: Add support for SPEAr SMI driverVipin KUMAR2012-07-074-9/+12
| | | | | | | | | | | | | | SMI is the serial memory interface controller provided by ST. Earlier, a driver exists in the u-boot source code for the SMI IP. However, it was specific to spear platforms. This commit converts the same driver to a more generic driver. As a result, the driver files are renamed to st_smi.c and st_smi.h and moved into drivers/mtd folder for reusability by other platforms using smi controller peripheral. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de>
* mtd/NAND: Remove obsolete SPEAr specific NAND driversVipin KUMAR2012-07-072-181/+0
| | | | | | | | | | | Since, SPEAr platform uses generic FSMC driver now, so spear specific files drivers/mtd/nand/spr_nand.c, arch/arm/include/asm/arch-spear/spr_nand.h are removed Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Scott Wood <scottwood@freescale.com>
* SPEAr: Configure FSMC driver for NAND interfaceVipin KUMAR2012-07-078-24/+49
| | | | | | | | | | | Since FSMC is a standard IP and it supports different memory interfaces, it is supported independent of spear platform and spear is configured to use that driver for interfacing with the NAND device Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Scott Wood <scottwood@freescale.com>
* mtd/NAND: Add FSMC driver supportVipin KUMAR2012-07-073-0/+588
| | | | | | | | | | | | | | Flexible static memory controller is a peripheral provided by ST, which controls the access to NAND chips along with many other memory device chips eg NOR, SRAM. This patch adds the driver support for FSMC controller interfacing with NAND memory. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Scott Wood <scottwood@freescale.com>
* arm/km: remove calls to kw_gpio_* in board_early_init_fHolger Brunck2012-07-072-15/+29
| | | | | | | | | | | | | | | | | | | | These functions tried to access two static tables before relocation (board_early_init_f is executed before relocation). But these static tables lie in the bss section which is not valid before relocation. These accesses then overwrote some parts of u-boot binary before it was relocated. For the kmnusa build, this results in a corrupted important env variable (bootcmd) but it may be that some other parts of the u-boot binary are corrupted. This patch solves this problem by moving all the kw_gpio_* calls to board_init, which should be early enough in the boot sequence. The only calls that could not be moved is the one for the SOFT (bitbang) I2C, and they have been replaced by a direct access to the GPIO dataout Control register to set the two GPIOs as output. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: add implementation for read_dip_switchThomas Herzmann2012-07-072-4/+13
| | | | | | | | | Add a function to read the dip_switch on kmcoge5un. If the switch is set the actual_bank is set to 0 and this SW is booted. Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
* arm/km: support the 2 PCIe fpga resetsValentin Longchamp2012-07-071-4/+9
| | | | | | | | | The PCIe FPGAs now have to support 2 resets: one for the non traffic affecting part (PCIe) and one for the traffic affecting part. When the FPGA is not reconfigured, we only reset the PCIe part. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* arm/km: skip FPGA config when already configuredValentin Longchamp2012-07-071-1/+40
| | | | | | | | | | | | | | | | In order to be able to perform board resets without interrupting the traffic, the configuration of an already properly configured FPGA is skipped. This is because some PCIe FPGAs embed some other function that must continue to work over reset. It is then the responsibility of the application to trigger a reconfiguration when needed. This is done by lowering the FPGA_INIT_B pin for delaying the configuration to u-boot @ next reboot, and then lower the FPGA_PROGRAM_B signal. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
* arm/km: redefine piggy 4 reg names to avoid conflictsValentin Longchamp2012-07-071-11/+11
| | | | | | | | | Some very similar #defines for reg addresses are used in a later patch (managed_switch support for km_arm). Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: cleanup km_kirkwood boardsHolger Brunck2012-07-072-3/+8
| | | | | | | | | | | | Remove config options from boards.cfg and simply add one switch per board and differ afterwards in km_kirkwood.h between the features. More boards are upcoming and therefore it's easier to have this at one place. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: enable BOCO2 FPGA download supportValentin Longchamp2012-07-077-10/+245
| | | | | | | | | | | | | | | | | | | | | | | This adds a first support of the FPGA download for a PCIe FPGA based on the BOCO2 CPLD. This takes place in 3 steps, all done accessing the SPICTRL reg of the BOCO2: 1) start the FPGA config with an access to the FPGA_PROG bit 2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to 1 for the end of the FPGA configuration (with a timeout) 3) reset the FPGA 4) finally remove the access to its config EEPROM from the FPGA so that the CPU can update the FPGA configuration when the kernel is running The boards with a PCIe FPGA but without BOCO2 still are supported. The config option name is CONFIG_KM_FPGA_CONFIG Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: remove portl2.h and use km_kirkwood insteadHolger Brunck2012-07-074-87/+10
| | | | | | | | | | | | The additional headerfile is unneeded here, we can use the generic km_kirkwood.h instead. And we can use the better config option KM_PIGGY4_88E6061 for the specific features for boards with this design in km_arm.c. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: convert mgcoge3un target to km_kirkwoodHolger Brunck2012-07-074-93/+51
| | | | | | | | | | | | Use the generic header km_kirkwood.h and get rid of the board specific header. changes for v2: rebased because of changes in other patches Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: add kmcoge5un board supportHolger Brunck2012-07-075-2/+316
| | | | | | | | | | | | | For u-boot this board is similar to mgcoge3un. But some differences are present. We have a different SDRAM on it and therefore a new SDRAM config file. Additionaly this board has a direct MAC/MAC connection from the kirkwood to a marvell simple switch without a phy inbetween, this needs a new configuration for the mvgbe driver. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm/km: add kmnusa board supportHolger Brunck2012-07-076-23/+391
| | | | | | | | | | | | | | | | This board is similar to portl2, but it has the u-boot environment in a SPI NOR flash and not in an i2c eeprom like portl2 have. Some other details: - IVM EEPROM is at adress: pca9547:70:9 - PCI is enabled - PIGGY4 is connected via MV88E6352 simple switch. There is no phy between the simple switch and the kirkwood. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> cc: Gerlando Falauto <gerlando.falauto@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com>
* arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0Tetsuyuki Kobayashi2012-07-071-1/+7
| | | | | | | | save_boot_params_default() in cpu.c accesses uninitialized stack area when it compiled with -O0 (not optimized). Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Acked-by: Tom Rini <trini@ti.com>
* cm-t35: fix incorrect NAND_ECC layout selectionNikita Kiryanov2012-07-071-1/+1
| | | | | | | | The current configuration selects an incorrect NAND ECC layout, which causes u-boot to write HW ECC data incorrectly. This patch selects the right layout. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.SRICHARAN R2012-07-072-7/+0
| | | | | | | | | | | | Currently on OMAP4/5 platforms, many kernel drivers are dependent upon the bootloaders for mux, dpll and clock configurations. This should not be the case and bootloaders should set only the minimum required for the uboot functionality and kernel boot. Note that this is going to break the kernel drivers. But this is the only way to get things fixed in the kernel. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4/5: Move USB pads to essential list.SRICHARAN R2012-07-072-22/+21
| | | | | | | | | USB module pads are getting enabled under non-essential group. These will be required for fastboot, tftp support. So move this to essential list to have them working when non-essential pads are no more muxed. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4/5: Move USB clocks to essential group.SRICHARAN R2012-07-072-9/+7
| | | | | | | | | USB clocks will be required for fastboot, tftp related functionalities. Move these clocks to essential group inorder to have the functionality working when non-essential clocks are not enabled. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4/5: Move gpmc clocks to essential group.SRICHARAN R2012-07-072-2/+2
| | | | | | | | | | GPMC clocks are currently getting enabled as a part non-essential clocks. This will be required during NOR boot. Move this to essential group to keep the functionality, when non-essential clocks are not enabled. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* ARM: OMAP4+: Move external phy initialisations to arch specific place.SRICHARAN R2012-07-074-27/+39
| | | | | | | | | | The external phy is present in the case OMAP5 soc is currently configured in emif-common.c. This results in having dummy structures for those Socs which do not have a external phy. So by having a weak function in emif-common and overriding it in OMAP5, avoids the use of dummy structures. Signed-off-by: R Sricharan <r.sricharan@ti.com>
* omap4: Use a smaller M,N couple for IVA DPLLSebastien Jan2012-07-071-1/+1
| | | | | | | | | | This reduced M,N couple corresponds to the advised value from TI HW team. Tested on 4460 Pandaboard, it also provides peripheral clocks closer to the advised values. Signed-off-by: Sebastien Jan <s-jan@ti.com>
* da850/omap-l138: Enable auto negotiation in RMII modeRajashekhara, Sudhakar2012-07-071-0/+8
| | | | | | | | | | | | On DA850/OMAP-L138 it was observed that in RMII mode, auto negotiation was not performed. This patch enables auto negotiation in RMII mode. Without this patch, EMAC initialization takes more time and sometimes tftp fails in RMII mode. Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com> Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com> Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
OpenPOWER on IntegriCloud