| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
* Remove symlinking of files located outside api_examples/
* Auto generate dependencies for files located outside api_examples/
* Update names of variables to be similar to those in tools/Makefile
* Fix out of tree build error
Dependencies are calculated for all files in the SRCS variable.
Previously, the SRCS variable contained files which were symlinked
into the api_examples/ directory. These symlinked files did not exist
when dependencies were calculated when building out of tree. This
resulted in errors such as:
make[1]: *** No rule to make target `/work/wd/tmp-ppc/api_examples/.depend', needed by `_depend'. Stop.
make[1]: Leaving directory `/home/wd/git/u-boot/work/api_examples'
make: *** [depend] Error 2
Since symlinked source files are no longer used, this bug no longer
exists.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Combining the two rules cleans up the Makefile a bit
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This cleans up the Makefile a bit and simplifies future changes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Rafal Jaworowski <raj@semihalf.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
|
| | |/ / /
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The current kallsyms code is using \\0 to escape the backslash in the awk
code, but the shell too needs escaping. This way we make sure gcc is
passed the \0. Then gcc itself will consume this as an octal, so we have
to use 000 so gcc will create the final NUL.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
| |/ / /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
| |/ /
| |
| |
| | |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |\ \ |
|
| | |\ \ |
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch makes pll_write on PPC405EP boards
global and callable from C code.
pll_write can be used to dynamically modify the PLB:PCI divider
as it is required for 33/66 MHz pci adapters based on the 405EP.
board_early_init_f() is a good place to do that (check M66EN signal
and call pll_write() when it is required).
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | | |
| | | |
| | | |
| | | | |
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch implements the is_pci_host() function in a similiar way
as it is used on 440 targets.
The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not
build on 405EP targets because checking the PCI arbiter is different.
So putting the fixed code into a separate function makes the code
more readable.
Also using is_pci_host() on 405 brings 405 and 440 PCI code
a little bit closer.
In preparation for an upcoming 405EP based PMC module I made this
function weak so that it can be overwritten from board specific code.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes a debug compilation error for PPC4xx platforms, all
other architectures are not affected by this change. The 'handler'
pointer was undefined. The fix is exercised and has effect only if
DEBUG is defined.
Signed-off-by: Alessio Centazzo acpatin@yahoo.com
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes printf format string compilation warnings in several
debug statements. It also fixes the dump of DDR controller MQ registers
found on some 44x and 46x platforms. The current register dump code
uses incorrect DCRs to access these registers.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
| |\ \ \
| |/ / |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If use the onenand boot, the env_relocate_spec() calls mtd->read(),
and the type of the argument #2 of mtd->read() was changed to loff_t.
But, the "env_addr" type is still unsigned long, thus this patch change
the type from unsigned long to loff_t.
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The bbt descriptors contains the pointer to the bbt pattern which
are statically initialized memory struct. When relocated to RAM,
these pointers will continue point to NOR flash(or L2 SRAM, or
other boot device). If the contents of NOR flash changed or L2
SRAM disabled, it'll hang the system.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When adding large page NAND support to this file, I had a misunderstanding
about the exact semantics of NAND_CTRL_CHANGE (which isn't documented
anywhere I can find) -- it is apparently just a hint to drivers,
which aren't required to preserve the old value for subsequent
non-"change" invocations.
This change makes nand_boot.c no longer assume this. Note that this
happened to work by chance with some NAND drivers, which don't preserve
the value, but treat 0 equivalently to NAND_CTRL_ALE.
I don't have hardware to test this, so any testing is appreciated.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The S3C2410 NAND driver source file is included in the makefile instead of
the object file.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
nand_util currently uses size_t which is arch dependent and not always a
unsigned long. Now use loff_t, as does the linux mtd layer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The "nand markbad" and "onenand markbad" commands did not check if an
argument was passed; if this was forgotten, no error was raised but
block 0 was marked as bad.
While fixing this bug, clean up the code a bit and allow to pass more
than one block address, thus allowing to mark several blocks as bad
in a single command invocation.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove an unused "total" variable in multiple functions.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does: as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:
Device 0: 2x nand0, sector size 128 KiB
Switch to use the default chipselect function unless the board
really needs its own. The logic for the Sonata board moves out
of the driver into board-specific code. (Which doesn't affect
current build breakage if its NAND support is enabled...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
All DaVinci SOC's use a CLE mask of 0x10 and an ALE mask of 0x8
except the DM646x. This was decided by the design team driving the design.
This patch updates the CLE and ALE values for DM646x.
Updated patches for DM646x will be sent shortly.
This applies to u-boot-nand-flash git
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The ALE mask used by DaVinci SOCs is wrong. The patch changes the mask value
from '0xa' to '0x8'. This is the mask we use for all TI releases.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Minor cleanup for DaVinci NAND code:
- Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
be defined when there are multiple chipselect lines in use
(as with common 2 GByte chips).
- Cleanup handling of EMIF control registers
* Only need one pointer pointing to them
* Remove incorrect and unused struct supersetting them
- Use the standard waitfunc; we don't need a custom version
- Partial legacy cleanup:
* Don't initialize every board like it's a DM6446 EVM
* #ifdef a bit more code for BROKEN_ECC
Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| |/
|
|
| |
Signed-off-by: Heiko Schocher <hs@denx.de>
|
| |\ |
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch allows the guard time parameter to be set in
the Atmel LCDC driver.
By default, the previous value of 1 is used, unless the
setting is defined elsewhere.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
|
| | |
| |
| |
| | |
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | | |
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
| | | |
| | |
| | |
| | | |
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| | | |
| | |
| | |
| | | |
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
This patch abstracts Kirkwood arch specific changes to support ehci-kirkwood driver
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Due to change in the usb_board_init() prototype, the USB for
the TrizepsIV was not correctly initialized.
Removed dummy print from usb_board_stop().
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch looks okay on u-boot-net.git/next branch
but when it was merged to u-boot.git/master the last line is missing
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
update against linux v2.6.30
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Correct define typo (. -> ,)
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
|
