summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2009-09-3013-1678/+2175
|\
| * ppc/85xx: get_law_entry isn't used in CONFIG_NAND_SPLKumar Gala2009-09-301-0/+4
| | | | | | | | | | | | | | Don't include get_law_entry as part of the NAND_SPL build since the code isnt used. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * Add README.mpc8536dsMingkai Hu2009-09-301-0/+127
| | | | | | | | | | | | | | Add boot from NAND/eSDHC/eSPI description Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * On-chip ROM boot: MPC8536DS supportMingkai Hu2009-09-304-1/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MPC8536E is capable of booting from the on-chip ROM - boot from eSDHC and boot from eSPI. When power on, the porcessor excutes the ROM code to initialize the eSPI/eSDHC controller, and loads the mian U-Boot image from the memory device that interfaced to the controller, such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or L2SRAM, then boot from it. The memory device should contain a specific data structure with control word and config word at the fixed address. The config word direct the process how to config the memory device, and the control word direct the processor where to find the image on the memory device, or where copy the main image to. The user can use any method to store the data structure to the memory device, only if store it on the assigned address. The on-chip ROM code will map the whole 4GB address space by setting entry0 in the TLB1, so the main image need to switch to Address space 1 to disable this mapping and map the address space again. This patch implements loading the mian U-Boot image into L2SRAM, so the image can configure the system memory by using SPD EEPROM. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * NAND boot: MPC8536DS supportMingkai Hu2009-09-307-18/+307
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MPC8536E can support booting from NAND flash which uses the image u-boot-nand.bin. This image contains two parts: a 4K NAND loader and a main U-Boot image. The former is appended to the latter to produce u-boot-nand.bin. The 4K NAND loader includes the corresponding nand_spl directory, along with the code twisted by CONFIG_NAND_SPL. The main U-Boot image just like a general U-Boot image except the parts that included by CONFIG_SYS_RAMBOOT. When power on, eLBC will automatically load from bank 0 the 4K NAND loader into the FCM buffer RAM where CPU can execute the boot code directly. In the first stage, the NAND loader copies itself to RAM or L2SRAM to free up the FCM buffer RAM, then loads the main image from NAND flash to RAM or L2SRAM and boot from it. This patch implements the NAND loader to load the main image into L2SRAM, so the main image can configure the RAM by using SPD EEPROM. In the first stage, the NAND loader copies itself to the second to last 4K address space, and uses the last 4K address space as the initial RAM for stack. Obviously, the size of L2SRAM shouldn't be less than the size of the image used. If so, the workaround is to generate another image that includes the code to configure the RAM by SPD and load it to L2SRAM first, then relocate the main image to RAM to boot up. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * mpc8536: fix board config file line lengthMingkai Hu2009-09-301-68/+79
| | | | | | | | | | Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * sbc8548: reclaim wasted sector in boot flashPaul Gortmaker2009-09-303-4/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | By nature of being based off the MPC8548CDS board, this board inherited an ENV_SIZE setting of 256k. But since it has a smaller flash device (8MB soldered on), it has a native sector size of 128k, and hence the ENV_SIZE was causing 2 sectors to be used for the environment. By removing the unused sector, we can push TEXT_BASE up closer to the end of address space and reclaim that sector for any other application. This also fixes the mismatch between TEXT_BASE and MONITOR_LEN reported by Kumar earlier. Since this board also supports the ability to boot off the 64MB SODIMM flash, this change is forward looking with that in mind; i.e. the settings for MONITOR_LEN and ENV_SIZE will work when the 512k sectors of the SODIMM flash are used for alternate boot in the future. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/85xx: Clean up immap_85xx.hKumar Gala2009-09-281-1589/+1586
| | | | | | | | | | | | | | | | | | * Converted all white space to tabs * Converted all types to u8/u16/u32 * Reduce lines to fit in 80 columns * Renamed MPC85xx_{Q,B}MAN -> FSL_CORENET_{Q,B}MAN Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk2009-09-306-23/+42
|\ \
| * | NAND: davinci: Fix warnings when 4-bit ECC not usedScott Wood2009-09-281-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | I accidentally left v2 of "NAND: DaVinci:Adding 4 BIT ECC support" applied when I pushed the tree last merge window, and missed these fixes which were in v3 of that patch. Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * | Refactor OneNAND IPL codeKyungmin Park2009-09-284-20/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Refactoring the OneNAND IPL code and some minor fixed: - Remove unnecessary header file - Fix wrong access at read interrupt - The recent OneNAND has 4KiB pagesize Also Board can override OneNAND IPL image Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
| * | MIPS: VCT: Remove read_spareram referenceShinya Kuribayashi2009-09-281-1/+0
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit ecad289fc6bd9d89ef4d5093cc7b6fd712fd0d29 (OneNAND: Remove unused read_spareram and add unlock_all as kernel does) forgot to remove a local reference to read_spareram in board/micronas/vct/ebi_onenand.c, which causes the following build failure when configured with OneNAND: ebi_onenand.c: In function 'onenand_board_init': ebi_onenand.c:196: error: 'struct onenand_chip' has no member named 'read_spareram' make[1]: *** [ebi_onenand.o] Error 1 make[1]: *** Waiting for unfinished jobs.... make: *** [board/micronas/vct/libvct.a] Error 2 Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com> Acked-by: Stefan Roese <sr@denx.de> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-ubiWolfgang Denk2009-09-301-1/+1
|\ \
| * | ubifs: Correct dereferencing of files-after-symlinksSimon Kagstrom2009-09-281-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Files in directories which are symlinked to were not dereferenced correctly in last commit. E.g., with a symlink /boot/lnk -> /boot/real_dir loading /boot/lnk/uImage will fail. This patch fixes that by simply seeing to it that the target base directory has a slash after it. Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net> Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2009-09-3085-1388/+1358
|\ \
| * | ppc4xx: Remove mtsdram0() marcos and use common mtsdram() insteadStefan Roese2009-09-282-22/+20
| | | | | | | | | | | | | | | | | | Additionally some whitespace coding style fixes. Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx: Convert PPC4xx SDRAM defines from lower case to upper caseStefan Roese2009-09-2826-357/+341
| | | | | | | | | | | | | | | | | | | | | | | | | | | The latest PPC4xx register cleanup patch missed some SDRAM defines. This patch now changes lower case UIC defines to upper case. Also some names are changed to match the naming in the IBM/AMCC users manuals (e.g. mem_mcopt1 -> SDRAM0_CFG). Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx: Convert PPC4xx UIC defines from lower case to upper caseStefan Roese2009-09-2872-1029/+1017
| |/ | | | | | | | | | | | | The latest PPC4xx register cleanup patch missed the UIC defines. This patch now changes lower case UIC defines to upper case. Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk2009-09-301-36/+69
|\ \
| * | fsl_i2c: Do not generate STOP after read.Joakim Tjernlund2009-09-281-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | __i2c_read always ends with a STOP condition thereby releasing the bus. It is cleaner to do the STOP magic in i2c_read(), like i2c_write() does. This may also help future multimaster systems which wants to hold on to the bus until all transactions are finished. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
| * | fsl_i2c: Impl. AN2919, rev 5 to calculate FDR/DFSRJoakim Tjernlund2009-09-281-35/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | The latest AN2919 has changed the way FDR/DFSR should be calculated. Update the driver according to spec. However, Condition 2 is not accounted for as it is not clear how to do so. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Wolfgang Grandegger <wg@grandegger.com>
| * | fsl_i2c: Add CONFIG_FSL_I2C_CUSTOM_{DFSR/FDR}Joakim Tjernlund2009-09-281-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Some boards need a higher DFSR value than the spec currently recommends so give these boards the means to define there own. For completeness, add CONFIG_FSL_I2C_CUSTOM_FDR too. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
| * | fsl_i2c: Wait for STOP condition to propagateJoakim Tjernlund2009-09-281-4/+8
| |/ | | | | | | | | | | | | | | | | | | | | | | | | After issuing a STOP one must wait until the STOP has completed on the bus before doing something new to the controller. Also add an extra read of SR as the manual mentions doing that is a good idea. Remove surplus write of CR just before a write, isn't required and could potentially disturb the I2C bus. Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk2009-09-3022-148/+292
|\ \
| * | mpc83xx: retain POR values of non-configured ACR, SPCR, SCCR, and LCRR bitfieldsKim Phillips2009-09-2617-123/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | some LCRR bits are not documented throughout the 83xx family RMs. New board porters copying similar board configurations might omit setting e.g., DBYP since it was not documented in their SoC's RM. Prevent them bricking their board by retaining power on reset values in bit fields that the board porter doesn't explicitly configure via CONFIG_SYS_<registername>_<bitfield> assignments in the board config file. also move LCRR assignment to cpu_init_r[am] to help ensure no transactions are being executed via the local bus while CLKDIV is being modified. also start to use i/o accessors. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | sbc8349: tidy up Makefile to use new configuration script.Paul Gortmaker2009-09-252-14/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 804d83a5 allows us to move all the configuration variation tweaks out of the top level Makefile and down into the board config header. This takes advantage of that for the sbc8349 board. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: mpc8360emds: Add QE USB device tree fixupsAnton Vorontsov2009-09-252-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | With this patch we can change QE USB mode without need to hand-edit the device tree. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: mpc8360emds: Use RGMII-ID mode, add workarounds for rev. 2.1 CPUsAnton Vorontsov2009-09-252-8/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes various ethernet issues with gigabit links handling in U-Boot. The workarounds originally implemented by Kim Phillips for Linux kernel. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | mpc83xx: mpc8360emds: Don't use LBC SDRAM when DDR is availableAnton Vorontsov2009-09-251-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 5c2ff323a94e27e481f70c44838d43fcd844dd46 ("mpc8360emds: rework LBC SDRAM setup"), LBC SDRAM is available for use in Linux. Though, it appears that QE Ethernet in Gigabit mode can't transmit large packets when it tries to work with a data in LBC SDRAM (memtest didn't discover any issues, is LBC SDRAM just too slow?). With this patch we can still use the board without DDR memory, but if DDR is available, we don't use LBC SDRAM. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | net: uec: Fix uccf.h and uec.h headers to include headers they depend onAnton Vorontsov2009-09-252-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | Headers should include headers containing prototypes and defines they depend on, don't assume that they're included by somebody else. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
| * | net: uec_phy: Implement TXID and RXID RGMII modes for Marvell PHYsAnton Vorontsov2009-09-252-2/+14
| |/ | | | | | | | | | | | | This will be needed for MPC8360E-MDS boards with rev. 2.1 CPUs. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-fdtWolfgang Denk2009-09-301-8/+15
|\ \ | |/ |/|
| * cmd_fdt.c: fix parse of byte streams and stringsKen MacLeod2009-09-241-8/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 4abd844d8e extended the fdt command parser to handle property strings which are split across multiple arguments but it was broken for byte streams and strings. Byte stream parsing: * Fixes where it would terminate early or go into an endless loop. * Fixes a 0x00 being inserted into the data if there is a space after '[' or a separate argument. * Fixes dereferencing the argument pointer after the last argument. * Checks for bad characters. String parsing: * Treat multiple arguments as a string list. This fixes an issue where only the last argument was stored. Signed-off-by: Ken MacLeod <ken@bitsko.slc.ut.us>
* | mpc5121ads: fix breakage introduced when reordering elpida_mddrc_config[]Wolfgang Denk2009-09-251-1/+1
|/ | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* mucmc52, uc101: delete ata@3a00 node, if no CF card is detectedHeiko Schocher2009-09-255-0/+41
| | | | | | | | | | | U-Boot can detect if an IDE device is present or not. If not, and this new config option is activated, U-Boot removes the ATA node from the DTS before booting Linux, so the Linux IDE driver does not probe the device and crash. This is needed for buggy hardware (uc101) where no pull down resistor is connected to the signal IDE5V_DD7. Signed-off-by: Heiko Schocher <hs@denx.de>
* mpc5200, mucmc52, uc101: config cleanupHeiko Schocher2009-09-256-504/+404
| | | | | | | | | | | | | | - As these boards are similiar, collect common config options in manroland/common.h and manroland/mpc52xx-common.h for mpc5200 specific common options for this manufacturer. - add OF support - update default environment Signed-off-by: Heiko Schocher <hs@denx.de> Minor edit of commit message. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Fix "ppc/85xx: Clean up use of LAWAR defines" breakageWolfgang Denk2009-09-251-1/+1
| | | | | | | | | Commit 002741ae86 modified include/asm-ppc/mmu.h such that the LAWAR_ defines were only enabled for the 83xx platform, but they are also needed on MPC512x system. Enabling these for E300 systems seems thus more appropriate. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Add Elpida Memory Configuration to mpc5121ads BoardsMartha M Stan2009-09-252-4/+130
| | | | | | | | Signed-off-by: Martha M Stan <mmarx@silicontkx.com> Minor coding style cleanup. Signed-off-by: Wolfgang Denk <wd@denx.de>
* mpc512x: Streamlined fixed_sdram() init sequence.Martha M Stan2009-09-259-82/+109
| | | | | | | | | | | | | | | | | | | Signed-off-by: Martha M Stan <mmarx@silicontkx.com> Minor cleanup: Re-ordered default_mddrc_config[] to have matching indices. This allows to use the same index "N" for source and target fields; before, we had code like this out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]); which always looked like a copy & paste error because 2 != 3. Also, use NULL when meaning a null pointer. Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk2009-09-2457-774/+1559
|\
| * ppc/p4080: Determine various chip frequencies on CoreNet platformsKumar Gala2009-09-243-4/+133
| | | | | | | | | | | | | | | | | | | | The means to determine the core, bus, and DDR frequencies are completely new on CoreNet style platforms. Additionally on p4080 we can have different frequencies for FMAN and PME IP blocks. We need to keep track of the FMAN & PME frequencies since they are used for time stamping capabilities inside each block. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/p4080: Handle timebase enabling and frequency reportingKumar Gala2009-09-243-1/+22
| | | | | | | | | | | | | | | | | | On CoreNet style platforms the timebase frequency is the bus frequency defined by 16 (on PQ3 it is divide by 8). Also on the CoreNet platforms the core not longer controls the enabling of the timebase. We now need to enable the boot core's timebase via CCSR register writes. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/p4080: Add various p4080 related defines (and p4040)Kumar Gala2009-09-245-2/+15
| | | | | | | | | | | | | | | | | | | | | | There are various locations that we have chip specific info: * Makefile for which ddr code to build * Added p4080 & p4040 to cpu_type_list and SVR list * Added number of LAWs for p4080 * Set CONFIG_MAX_CPUS to 8 for p4080 Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/p4080: CoreNet platfrom style secondary core releaseKumar Gala2009-09-241-3/+65
| | | | | | | | | | | | | | | | | | The CoreNet platform style of bringing secondary cores out of reset is a bit different that the PQ3 style. Mostly the registers that we use to setup boot translation, enable time bases, and boot release the cores have moved around. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/p4080: CoreNet platfrom style CCSRBAR settingKumar Gala2009-09-241-18/+54
| | | | | | | | | | | | | | | | On CoreNet based platforms the CCSRBAR address is split between an high & low register and we no longer shift the address. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
| * ppc/p4080: Add support for CoreNet style platform LAWsKumar Gala2009-09-242-11/+146
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On CoreNet based platforms the LAW address is split between an high & low register and we no longer shift the address. Also, the target IDs on CoreNet platforms have been completely re-assigned. Additionally, added a new find_law() API to which LAW an address hits in. This is need for the CoreNet style boot release code since it will need to determine what the target ID should be set to for boot window translation. Finally, enamed LAWAR_EN to LAW_EN and moved to header so we can use it elsewhere. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/p4080: Add p4080 platform immap definitionsKumar Gala2009-09-242-20/+271
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The p4080 SoC has a significant amount of commonality with the 85xx/PQ3 platform. We reuse the 85xx immap and just add new definitions for local access and global utils. The global utils is now broken into global utils, clocking and run control/power management. The offsets from CCSR for a number of blocks have also changed. We introduce the CONFIG_FSL_CORENET define to distinquish the PQ3 style of platform from the new p4080 platform. We don't use QoirQ as there are products (like p2020) that are PQ3 based platforms but have the QoirQ name. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/85xx: Fix enabling of L2 cacheKumar Gala2009-09-242-3/+4
| | | | | | | | | | | | | | We need to flash invalidate the locks in addition to the cache before we enable. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * 85xx-fdt: Fixed l2-ctlr's compatible prop for QorIQVivek Mahajan2009-09-241-3/+10
| | | | | | | | | | | | | | | | The code assumed names where just numbers and always prefixed 'mpc'. However newer QorIQ don't follow the mpc naming scheme. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * ppc/85xx: add cpu init config file for boot from NANDMingkai Hu2009-09-241-0/+63
| | | | | | | | | | | | | | | | | | When boot from NAND, the NAND flash must be connected to br/or0. Also init RAM(L2 SRAM or DDR SDRAM) for load the second image to it. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
OpenPOWER on IntegriCloud