diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/B4860QDS.h | 12 | ||||
| -rw-r--r-- | include/configs/T104xRDB.h | 20 | ||||
| -rw-r--r-- | include/configs/ls1021aqds.h | 4 | ||||
| -rw-r--r-- | include/configs/ls2085a_common.h | 87 | ||||
| -rw-r--r-- | include/configs/ls2085a_emu.h | 1 | ||||
| -rw-r--r-- | include/configs/ls2085a_simu.h | 9 | ||||
| -rw-r--r-- | include/fdt_support.h | 12 | ||||
| -rw-r--r-- | include/fsl_ddr.h | 15 | ||||
| -rw-r--r-- | include/fsl_ddr_sdram.h | 18 |
9 files changed, 154 insertions, 24 deletions
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index 953d06b53c..9063c57b40 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -227,6 +227,7 @@ unsigned long get_board_ddr_clk(void); #endif /* EEPROM */ +#define CONFIG_ID_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_SYS_EEPROM_BUS_NUM 0 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 @@ -819,9 +820,16 @@ unsigned long get_board_ddr_clk(void); #define __USB_PHY_TYPE ulpi +#ifdef CONFIG_PPC_B4860 +#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \ + "bank_intlv=cs0_cs1;" \ + "en_cpc:cpc2;" +#else +#define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;" +#endif + #define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:ctlr_intlv=null," \ - "bank_intlv=cs0_cs1;" \ + HWCONFIG \ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h index d4c6f588b6..5e2c100d93 100644 --- a/include/configs/T104xRDB.h +++ b/include/configs/T104xRDB.h @@ -19,6 +19,9 @@ #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1040_rcw.cfg #endif #ifdef CONFIG_T1042RDB_PI +#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1042_pi_rcw.cfg +#endif +#ifdef CONFIG_T1042RDB #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t104xrdb/t1042_rcw.cfg #endif @@ -477,7 +480,7 @@ /* I2C bus multiplexer */ #define I2C_MUX_PCA_ADDR 0x70 -#ifdef CONFIG_T1040RDB +#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB) #define I2C_MUX_CH_DEFAULT 0x8 #endif @@ -634,7 +637,7 @@ #define CONFIG_SYS_DPAA_FMAN #define CONFIG_SYS_DPAA_PME -#ifdef CONFIG_T1040RDB +#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB) #define CONFIG_QE #define CONFIG_U_QE #endif @@ -663,7 +666,7 @@ #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 #endif -#ifdef CONFIG_T1040RDB +#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB) #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_QE_FW_ADDR 0x130000 #elif defined(CONFIG_SDCARD) @@ -687,7 +690,7 @@ #endif #ifdef CONFIG_FMAN_ENET -#ifdef CONFIG_T1040RDB +#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1042RDB) #define CONFIG_SYS_SGMII1_PHY_ADDR 0x03 #endif #define CONFIG_SYS_RGMII1_PHY_ADDR 0x01 @@ -789,13 +792,14 @@ #define CONFIG_BAUDRATE 115200 #define __USB_PHY_TYPE utmi +#define RAMDISKFILE "t104xrdb/ramdisk.uboot" #ifdef CONFIG_T1040RDB #define FDTFILE "t1040rdb/t1040rdb.dtb" -#define RAMDISKFILE "t1040rdb/ramdisk.uboot" -#elif CONFIG_T1042RDB_PI -#define FDTFILE "t1040rdb_pi/t1040rdb_pi.dtb" -#define RAMDISKFILE "t1040rdb_pi/ramdisk.uboot" +#elif defined(CONFIG_T1042RDB_PI) +#define FDTFILE "t1042rdb_pi/t1042rdb_pi.dtb" +#elif defined(CONFIG_T1042RDB) +#define FDTFILE "t1042rdb/t1042rdb.dtb" #endif #ifdef CONFIG_FSL_DIU_FB diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h index 657e3b6d48..bb47813345 100644 --- a/include/configs/ls1021aqds.h +++ b/include/configs/ls1021aqds.h @@ -49,10 +49,12 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_DDR_SPD #define SPD_EEPROM_ADDRESS 0x51 #define CONFIG_SYS_SPD_BUS_NUM 0 -#define CONFIG_SYS_DDR_RAW_TIMING #define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ +#ifndef CONFIG_SYS_FSL_DDR4 #define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */ +#define CONFIG_SYS_DDR_RAW_TIMING +#endif #define CONFIG_DIMM_SLOTS_PER_CTLR 1 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 diff --git a/include/configs/ls2085a_common.h b/include/configs/ls2085a_common.h index 2bd5a472b3..a72e1f3567 100644 --- a/include/configs/ls2085a_common.h +++ b/include/configs/ls2085a_common.h @@ -15,9 +15,11 @@ #define CONFIG_GICV3 /* Link Definitions */ -#define CONFIG_SYS_TEXT_BASE 0x30000000 +#define CONFIG_SYS_TEXT_BASE 0x30001000 +#ifdef CONFIG_EMU #define CONFIG_SYS_NO_FLASH +#endif #define CONFIG_SUPPORT_RAW_INITRD @@ -45,13 +47,27 @@ #define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ -/* SMP Definitions */ -#define CPU_RELEASE_ADDR CONFIG_SYS_INIT_SP_ADDR - #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL +#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 + +/* + * SMP Definitinos + */ +#define CPU_RELEASE_ADDR secondary_boot_func + +#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS +#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL +/* + * DDR controller use 0 as the base address for binding. + * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access. + */ +#define CONFIG_SYS_DP_DDR_BASE_PHY 0 +#define CONFIG_DP_DDR_CTRL 2 +#define CONFIG_DP_DDR_NUM_CTRLS 1 +#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 /* Generic Timer Definitions */ #define COUNTER_FREQUENCY 12000000 /* 12MHz */ @@ -118,6 +134,66 @@ #define CONFIG_SYS_NOR_FTIM3 0x04000000 #define CONFIG_SYS_IFC_CCR 0x01000000 +#ifndef CONFIG_SYS_NO_FLASH +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE +#define CONFIG_SYS_FLASH_QUIET_TEST +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#endif + +#define CONFIG_NAND_FSL_IFC +#define CONFIG_SYS_NAND_MAX_ECCPOS 256 +#define CONFIG_SYS_NAND_MAX_OOBFREE 2 +#define CONFIG_SYS_NAND_BASE 0x520000000 +#define CONFIG_SYS_NAND_BASE_PHYS 0x20000000 + +#define CONFIG_SYS_NAND_CSPR_EXT (0x0) +#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ + | CSPR_MSEL_NAND /* MSEL = NAND */ \ + | CSPR_V) +#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) + +#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ + | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ + | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ + | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ + | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ + | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ + | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ + +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* ONFI NAND Flash mode0 Timing Params */ +#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ + FTIM0_NAND_TWP(0x18) | \ + FTIM0_NAND_TWCHT(0x07) | \ + FTIM0_NAND_TWH(0x0a)) +#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ + FTIM1_NAND_TWBE(0x39) | \ + FTIM1_NAND_TRR(0x0e) | \ + FTIM1_NAND_TRP(0x18)) +#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ + FTIM2_NAND_TREH(0x0a) | \ + FTIM2_NAND_TWHRE(0x1e)) +#define CONFIG_SYS_NAND_FTIM3 0x0 + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND + +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR @@ -167,6 +243,7 @@ /* Miscellaneous configurable options */ #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) +#define CONFIG_ARCH_EARLY_INIT_R /* Physical Memory Map */ /* fixme: these need to be checked against the board */ @@ -174,7 +251,7 @@ #define CONFIG_SYS_CLK_FREQ 133333333 -#define CONFIG_NR_DRAM_BANKS 2 +#define CONFIG_NR_DRAM_BANKS 3 #define CONFIG_SYS_HZ 1000 diff --git a/include/configs/ls2085a_emu.h b/include/configs/ls2085a_emu.h index a5cea63b33..487cd99c5d 100644 --- a/include/configs/ls2085a_emu.h +++ b/include/configs/ls2085a_emu.h @@ -13,6 +13,7 @@ #define CONFIG_SYS_FSL_DDR_EMU /* Support emulator */ #define SPD_EEPROM_ADDRESS1 0x51 #define SPD_EEPROM_ADDRESS2 0x52 +#define SPD_EEPROM_ADDRESS3 0x53 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 #define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD on I2C bus 1 */ diff --git a/include/configs/ls2085a_simu.h b/include/configs/ls2085a_simu.h index 46d47b06e4..0f40b787b4 100644 --- a/include/configs/ls2085a_simu.h +++ b/include/configs/ls2085a_simu.h @@ -13,4 +13,13 @@ #define CONFIG_SMC91111 #define CONFIG_SMC91111_BASE (0x2210000) +#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 + #endif /* __LS2_SIMU_H */ diff --git a/include/fdt_support.h b/include/fdt_support.h index 1bda686a0b..c3d1fbcf35 100644 --- a/include/fdt_support.h +++ b/include/fdt_support.h @@ -133,6 +133,18 @@ static inline int fdt_status_fail_by_alias(void *fdt, const char *alias) return fdt_set_status_by_alias(fdt, alias, FDT_STATUS_FAIL, 0); } +/* Helper to read a big number; size is in cells (not bytes) */ +static inline u64 of_read_number(const fdt32_t *cell, int size) +{ + u64 r = 0; + while (size--) + r = (r << 32) | fdt32_to_cpu(*(cell++)); + return r; +} + +void of_bus_default_count_cells(void *blob, int parentoffset, + int *addrc, int *sizec); + #endif /* ifdef CONFIG_OF_LIBFDT */ #ifdef USE_HOSTCC diff --git a/include/fsl_ddr.h b/include/fsl_ddr.h index 5c49b229da..675557ad1f 100644 --- a/include/fsl_ddr.h +++ b/include/fsl_ddr.h @@ -15,6 +15,11 @@ #include <common_timing_params.h> +#ifndef CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS +/* All controllers are for main memory */ +#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS CONFIG_NUM_DDR_CONTROLLERS +#endif + #ifdef CONFIG_SYS_FSL_DDR_LE #define ddr_in32(a) in_le32(a) #define ddr_out32(a, v) out_le32(a, v) @@ -57,6 +62,13 @@ typedef struct { memctl_options_t memctl_opts[CONFIG_SYS_NUM_DDR_CTLRS]; common_timing_params_t common_timing_params[CONFIG_SYS_NUM_DDR_CTLRS]; fsl_ddr_cfg_regs_t fsl_ddr_config_reg[CONFIG_SYS_NUM_DDR_CTLRS]; + unsigned int first_ctrl; + unsigned int num_ctrls; + unsigned long long mem_base; + unsigned int dimm_slots_per_ctrl; + int (*board_need_mem_reset)(void); + void (*board_mem_reset)(void); + void (*board_mem_de_reset)(void); } fsl_ddr_info_t; /* Compute steps */ @@ -72,7 +84,6 @@ typedef struct { unsigned long long fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, unsigned int size_only); - const char *step_to_string(unsigned int step); unsigned int compute_fsl_memctl_config_regs(const memctl_options_t *popts, @@ -102,7 +113,7 @@ void fsl_ddr_set_lawbar( int fsl_ddr_interactive_env_var_exists(void); unsigned long long fsl_ddr_interactive(fsl_ddr_info_t *pinfo, int var_is_set); void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd, - unsigned int ctrl_num); + unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl); int do_reset(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]); unsigned int check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr); diff --git a/include/fsl_ddr_sdram.h b/include/fsl_ddr_sdram.h index 987119b014..5b03c14c55 100644 --- a/include/fsl_ddr_sdram.h +++ b/include/fsl_ddr_sdram.h @@ -51,7 +51,6 @@ typedef ddr2_spd_eeprom_t generic_spd_eeprom_t; #define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR2 #endif #elif defined(CONFIG_SYS_FSL_DDR3) -#define FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR (3) /* FIXME */ typedef ddr3_spd_eeprom_t generic_spd_eeprom_t; #ifndef CONFIG_FSL_SDRAM_TYPE #define CONFIG_FSL_SDRAM_TYPE SDRAM_TYPE_DDR3 @@ -352,7 +351,6 @@ typedef struct memctl_options_s { unsigned int twot_en; unsigned int threet_en; unsigned int bstopre; - unsigned int tcke_clock_pulse_width_ps; /* tCKE */ unsigned int tfaw_window_four_activates_ps; /* tFAW -- FOUR_ACT */ /* Rtt impedance */ @@ -379,12 +377,20 @@ typedef struct memctl_options_s { unsigned int trwt; /* read-to-write turnaround */ } memctl_options_t; -extern phys_size_t fsl_ddr_sdram(void); -extern phys_size_t fsl_ddr_sdram_size(void); +phys_size_t fsl_ddr_sdram(void); +phys_size_t fsl_ddr_sdram_size(void); +phys_size_t fsl_other_ddr_sdram(unsigned long long base, + unsigned int first_ctrl, + unsigned int num_ctrls, + unsigned int dimm_slots_per_ctrl, + int (*board_need_reset)(void), + void (*board_reset)(void), + void (*board_de_reset)(void)); extern int fsl_use_spd(void); -extern void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, - unsigned int ctrl_num, int step); +void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs, + unsigned int ctrl_num, int step); u32 fsl_ddr_get_intl3r(void); +void print_ddr_info(unsigned int start_ctrl); static void __board_assert_mem_reset(void) { |
