diff options
Diffstat (limited to 'include/configs')
68 files changed, 423 insertions, 9349 deletions
diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h index eeb0671ddb..6aaaaa43f0 100644 --- a/include/configs/BSC9131RDB.h +++ b/include/configs/BSC9131RDB.h @@ -433,6 +433,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ #define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 10 /* -1 disable auto-boot */ #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h index e8a8d299cd..59a8d1b5d1 100644 --- a/include/configs/BSC9132QDS.h +++ b/include/configs/BSC9132QDS.h @@ -675,6 +675,7 @@ combinations. this should be removed later #define CONFIG_UBOOTPATH "u-boot.bin" #define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 10 /* -1 disable auto-boot */ #ifdef CONFIG_SDCARD #define CONFIG_DEF_HWCONFIG "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h index ecb3d7b25f..e24b923368 100644 --- a/include/configs/C29XPCIE.h +++ b/include/configs/C29XPCIE.h @@ -581,4 +581,6 @@ #define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND +#include <asm/fsl_secure_boot.h> + #endif /* __CONFIG_H */ diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h deleted file mode 100644 index 27539d27d7..0000000000 --- a/include/configs/CATcenter.h +++ /dev/null @@ -1,750 +0,0 @@ -/* - * ueberarbeitet durch Christoph Seyfert - * - * (C) Copyright 2004-2005 DENX Software Engineering, - * Wolfgang Grandegger <wg@denx.de> - * (C) Copyright 2003 - * DAVE Srl - * - * http://www.dave-tech.it - * http://www.wawnet.biz - * mailto:info@wawnet.biz - * - * Credits: Stefan Roese, Wolfgang Denk - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */ -#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */ -#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */ -#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL -#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA -#endif - -/* Only one of the following two symbols must be defined (default is 25 MHz) - * CONFIG_PPCHAMELEON_CLK_25 - * CONFIG_PPCHAMELEON_CLK_33 - */ -#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_PPCHAMELEON_CLK_25 -#endif - -#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) -#error "* Two external frequencies (SysClk) are defined! *" -#endif - -#undef CONFIG_PPCHAMELEON_SMI712 - -/* - * Debug stuff - */ -#undef __DEBUG_START_FROM_SRAM__ -#define __DISABLE_MACHINE_EXCEPTION__ - -#ifdef __DEBUG_START_FROM_SRAM__ -#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4 -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405EP 1 /* This is a PPC405 CPU */ -#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */ -#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds" - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#else -# error "* External frequency (SysClk) not defined! *" -#endif - -#define CONFIG_CONS_INDEX 2 /* Use UART1 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_VERSION_VARIABLE 1 /* add version variable */ -#define CONFIG_IDENT_STRING "1" - -#undef CONFIG_BOOTARGS - -/* Ethernet stuff */ -#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */ -#define CONFIG_ETHADDR 00:50:C2:1E:AF:FE -#define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:50:C2:1E:AF:FD - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -#define CONFIG_PPC4xx_EMAC -#undef CONFIG_EXT_PHY - -#define CONFIG_MII 1 /* MII PHY management */ -#ifndef CONFIG_EXT_PHY -#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */ -#define CONFIG_PHY1_ADDR 16 /* EMAC1 PHY address */ -#else -#define CONFIG_PHY_ADDR 2 /* PHY address */ -#endif -#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/ -#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */ - -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -/*----------------------------------------------------------------------- - * NAND-FLASH stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_NAND0_BASE 0xFF400000 -#define CONFIG_SYS_NAND1_BASE 0xFF000000 -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE } -#define NAND_BIG_DELAY_US 25 - -/* For CATcenter there is only NAND on the module */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -#define NAND_NO_RB - -#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ -#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ - -#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */ -#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */ -#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ -#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ - - -#define MACRO_NAND_DISABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_ENABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRCLE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETCLE(nandptr) do { \ - switch((unsigned long)nandptr) { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -#ifdef NAND_NO_RB -/* constant delay (see also tR in the datasheet) */ -#define NAND_WAIT_READY(nand) do { \ - udelay(12); \ -} while (0) -#else -/* use the R/B pin */ -/* TBD */ -#endif - -#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0) -#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0) -#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr)) - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#if 0 /* No PCI on CATcenter */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ - -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ -#endif /* No PCI */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ -/* - * The following defines are added for buggy IOP480 byte interface. - * All other boards should use the standard values (CPCI405 etc.) - */ -#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ -#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ -#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/*----------------------------------------------------------------------- - * Environment Variable setup - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */ -#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/ -#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000 -#define CONFIG_ENV_SIZE_REDUND 0x2000 - -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ - -/*----------------------------------------------------------------------- - * I2C EEPROM (CAT24WC16) for environment - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x92015480 -#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ - -/* Memory Bank 1 (External SRAM) initialization */ -/* Since this must replace NOR Flash, we use the same settings for CS0 */ -#define CONFIG_SYS_EBC_PB1AP 0x92015480 -#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x92015480 -#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x92015480 -#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ - -#ifdef CONFIG_PPCHAMELEON_SMI712 -/* - * Video console (graphic: SMI LynxEM) - */ -#define CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_VIDEO_LOGO -/*#define CONFIG_VIDEO_BMP_LOGO*/ -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VGA_AS_SINGLE_DEVICE -/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ -#define CONFIG_SYS_ISA_IO 0xE8000000 -/* see also drivers/video/videomodes.c */ -#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303 -#endif - -/*----------------------------------------------------------------------- - * FPGA stuff - */ -/* FPGA internal regs */ -#define CONFIG_SYS_FPGA_MODE 0x00 -#define CONFIG_SYS_FPGA_STATUS 0x02 -#define CONFIG_SYS_FPGA_TS 0x04 -#define CONFIG_SYS_FPGA_TS_LOW 0x06 -#define CONFIG_SYS_FPGA_TS_CAP0 0x10 -#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 -#define CONFIG_SYS_FPGA_TS_CAP1 0x14 -#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 -#define CONFIG_SYS_FPGA_TS_CAP2 0x18 -#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a -#define CONFIG_SYS_FPGA_TS_CAP3 0x1c -#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e - -/* FPGA Mode Reg */ -#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000 -#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000 - -/* FPGA Status Reg */ -#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 -#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 -#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 -#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 -#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000 - -#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ - -/* FPGA program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in data cache) - */ -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs -> GPIO - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30] - EMAC0 input - * GPIO0[31] - EMAC1 reject packet as output - */ -#define CONFIG_SYS_GPIO0_OSRL 0x40000550 -#define CONFIG_SYS_GPIO0_OSRH 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 -/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ -#define CONFIG_SYS_GPIO0_ISR1H 0x15555444 -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 -#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 - -#define CONFIG_NO_SERIAL_EEPROM - -/*--------------------------------------------------------------------*/ - -#ifdef CONFIG_NO_SERIAL_EEPROM - -/* -!----------------------------------------------------------------------- -! Defines for entry options. -! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that -! are plugged in the board will be utilized as non-ECC DIMMs. -!----------------------------------------------------------------------- -*/ -#undef AUTO_MEMORY_CONFIG -#define DIMM_READ_ADDR 0xAB -#define DIMM_WRITE_ADDR 0xAA - -/* Defines for CPC0_PLLMR1 Register fields */ -#define PLL_ACTIVE 0x80000000 -#define CPC0_PLLMR1_SSCS 0x80000000 -#define PLL_RESET 0x40000000 -#define CPC0_PLLMR1_PLLR 0x40000000 - /* Feedback multiplier */ -#define PLL_FBKDIV 0x00F00000 -#define CPC0_PLLMR1_FBDV 0x00F00000 -#define PLL_FBKDIV_16 0x00000000 -#define PLL_FBKDIV_1 0x00100000 -#define PLL_FBKDIV_2 0x00200000 -#define PLL_FBKDIV_3 0x00300000 -#define PLL_FBKDIV_4 0x00400000 -#define PLL_FBKDIV_5 0x00500000 -#define PLL_FBKDIV_6 0x00600000 -#define PLL_FBKDIV_7 0x00700000 -#define PLL_FBKDIV_8 0x00800000 -#define PLL_FBKDIV_9 0x00900000 -#define PLL_FBKDIV_10 0x00A00000 -#define PLL_FBKDIV_11 0x00B00000 -#define PLL_FBKDIV_12 0x00C00000 -#define PLL_FBKDIV_13 0x00D00000 -#define PLL_FBKDIV_14 0x00E00000 -#define PLL_FBKDIV_15 0x00F00000 - /* Forward A divisor */ -#define PLL_FWDDIVA 0x00070000 -#define CPC0_PLLMR1_FWDVA 0x00070000 -#define PLL_FWDDIVA_8 0x00000000 -#define PLL_FWDDIVA_7 0x00010000 -#define PLL_FWDDIVA_6 0x00020000 -#define PLL_FWDDIVA_5 0x00030000 -#define PLL_FWDDIVA_4 0x00040000 -#define PLL_FWDDIVA_3 0x00050000 -#define PLL_FWDDIVA_2 0x00060000 -#define PLL_FWDDIVA_1 0x00070000 - /* Forward B divisor */ -#define PLL_FWDDIVB 0x00007000 -#define CPC0_PLLMR1_FWDVB 0x00007000 -#define PLL_FWDDIVB_8 0x00000000 -#define PLL_FWDDIVB_7 0x00001000 -#define PLL_FWDDIVB_6 0x00002000 -#define PLL_FWDDIVB_5 0x00003000 -#define PLL_FWDDIVB_4 0x00004000 -#define PLL_FWDDIVB_3 0x00005000 -#define PLL_FWDDIVB_2 0x00006000 -#define PLL_FWDDIVB_1 0x00007000 - /* PLL tune bits */ -#define PLL_TUNE_MASK 0x000003FF -#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ -#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ -#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ -#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ -#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ -#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ -#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ - -/* Defines for CPC0_PLLMR0 Register fields */ - /* CPU divisor */ -#define PLL_CPUDIV 0x00300000 -#define CPC0_PLLMR0_CCDV 0x00300000 -#define PLL_CPUDIV_1 0x00000000 -#define PLL_CPUDIV_2 0x00100000 -#define PLL_CPUDIV_3 0x00200000 -#define PLL_CPUDIV_4 0x00300000 - /* PLB divisor */ -#define PLL_PLBDIV 0x00030000 -#define CPC0_PLLMR0_CBDV 0x00030000 -#define PLL_PLBDIV_1 0x00000000 -#define PLL_PLBDIV_2 0x00010000 -#define PLL_PLBDIV_3 0x00020000 -#define PLL_PLBDIV_4 0x00030000 - /* OPB divisor */ -#define PLL_OPBDIV 0x00003000 -#define CPC0_PLLMR0_OPDV 0x00003000 -#define PLL_OPBDIV_1 0x00000000 -#define PLL_OPBDIV_2 0x00001000 -#define PLL_OPBDIV_3 0x00002000 -#define PLL_OPBDIV_4 0x00003000 - /* EBC divisor */ -#define PLL_EXTBUSDIV 0x00000300 -#define CPC0_PLLMR0_EPDV 0x00000300 -#define PLL_EXTBUSDIV_2 0x00000000 -#define PLL_EXTBUSDIV_3 0x00000100 -#define PLL_EXTBUSDIV_4 0x00000200 -#define PLL_EXTBUSDIV_5 0x00000300 - /* MAL divisor */ -#define PLL_MALDIV 0x00000030 -#define CPC0_PLLMR0_MPDV 0x00000030 -#define PLL_MALDIV_1 0x00000000 -#define PLL_MALDIV_2 0x00000010 -#define PLL_MALDIV_3 0x00000020 -#define PLL_MALDIV_4 0x00000030 - /* PCI divisor */ -#define PLL_PCIDIV 0x00000003 -#define CPC0_PLLMR0_PPFD 0x00000003 -#define PLL_PCIDIV_1 0x00000000 -#define PLL_PCIDIV_2 0x00000001 -#define PLL_PCIDIV_3 0x00000002 -#define PLL_PCIDIV_4 0x00000003 - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) - -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#else -#error "* External frequency (SysClk) not defined! *" -#endif - -#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) -/* Model HI */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 -#define CONFIG_SYS_OPB_FREQ 55555555 -/* Model ME */ -#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#else -/* Model BA (default) */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#endif - -#endif /* CONFIG_NO_SERIAL_EEPROM */ - -#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ -#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nand" -#define CONFIG_JFFS2_PART_SIZE 0x00200000 -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support - * - * Note: fake mtd_id used, no linux mtd map file - */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nand0=catcenter" -#define MTDPARTS_DEFAULT "mtdparts=catcenter:2m(nand)" -*/ - -#endif /* __CONFIG_H */ diff --git a/include/configs/ELPPC.h b/include/configs/ELPPC.h deleted file mode 100644 index debfc3697e..0000000000 --- a/include/configs/ELPPC.h +++ /dev/null @@ -1,337 +0,0 @@ -/* - * (C) Copyright 2002 ELTEC Elektronik AG - * Frank Gottschling <fgottschling@eltec.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define GTREGREAD(x) 0xffffffff /* needed for debug */ - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -/* these hardware addresses are pretty bogus, please change them to - suit your needs */ - -/* first ethernet */ -#define CONFIG_ETHADDR 00:00:5b:ee:de:ad - -#define CONFIG_IPADDR 192.168.0.105 -#define CONFIG_SERVERIP 192.168.0.100 - -#define CONFIG_ELPPC 1 /* this is an BAB740/BAB750 board */ - -#define CONFIG_BAUDRATE 9600 /* console baudrate */ - -#undef CONFIG_WATCHDOG - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#undef CONFIG_BOOTARGS -#define CONFIG_BOOTCOMMAND \ - "bootp 1000000; " \ - "setenv bootargs root=ramfs console=ttyS00,9600 " \ - "ip=${ipaddr}:${serverip}:${rootpath}:${gatewayip}:" \ - "${netmask}:${hostname}:eth0:none; " \ - "bootm" - -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH - -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_JFFS2 - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -/* - * choose between COM1 and COM2 as serial console - */ -#define CONFIG_CONS_INDEX 1 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 64 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -#define CONFIG_SYS_BOARD_ASM_INIT -#define CONFIG_MISC_INIT_R - -/* - * Address mapping scheme for the MPC107 mem controller is mapping B (CHRP) - */ -#undef CONFIG_SYS_ADDRESS_MAP_A - -#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_SIZE 0x40000000 - -#define CONFIG_SYS_PCI_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI_MEM_SIZE 0x7d000000 - -#define CONFIG_SYS_ISA_MEM_BUS 0x00000000 -#define CONFIG_SYS_ISA_MEM_PHYS 0xfd000000 -#define CONFIG_SYS_ISA_MEM_SIZE 0x01000000 - -#define CONFIG_SYS_PCI_IO_BUS 0x00800000 -#define CONFIG_SYS_PCI_IO_PHYS 0xfe800000 -#define CONFIG_SYS_PCI_IO_SIZE 0x00400000 - -#define CONFIG_SYS_ISA_IO_BUS 0x00000000 -#define CONFIG_SYS_ISA_IO_PHYS 0xfe000000 -#define CONFIG_SYS_ISA_IO_SIZE 0x00800000 - -/* driver defines FDC,IDE,... */ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_ISA_IO_PHYS -#define CONFIG_SYS_ISA_IO CONFIG_SYS_ISA_IO_PHYS -#define CONFIG_SYS_60X_PCI_IO_OFFSET CONFIG_SYS_ISA_IO_PHYS - -/* - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_USR_LED_BASE 0x78000000 -#define CONFIG_SYS_NVRAM_BASE 0xff000000 -#define CONFIG_SYS_UART_BASE 0xff400000 -#define CONFIG_SYS_FLASH_BASE 0xfff00000 - -#define MPC107_EUMB_ADDR 0xfce00000 -#define MPC107_EUMB_PI 0xfce41090 -#define MPC107_EUMB_GCR 0xfce41020 -#define MPC107_EUMB_IACKR 0xfce600a0 -#define MPC107_I2C_ADDR 0xfce03000 - -/* - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x00fd0000 /* above the memtest region */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Flash mapping/organization on the MPC10x. - */ -#define FLASH_BASE0_PRELIM 0xff800000 -#define FLASH_BASE1_PRELIM 0xffc00000 - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=elppc-0,nor1=elppc-1" -#define MTDPARTS_DEFAULT "mtdparts=elppc-0:-(jffs2),elppc-1:-(user)" -*/ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN 0x20000 /* Reserve 128 kB for malloc() */ -#undef CONFIG_SYS_MEMTEST - -/* - * Environment settings - */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ -#define CONFIG_SYS_NVRAM_SIZE 0x800 /* NVRAM size (2kB) */ -#define CONFIG_ENV_SIZE 0x400 /* Size of Environment vars (1kB) */ -#define CONFIG_ENV_ADDR 0x0 -#define CONFIG_ENV_MAP_ADRS 0xff000000 -#define CONFIG_SYS_NV_SROM_COPY_ADDR (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) -#define CONFIG_SYS_NVRAM_ACCESS_ROUTINE /* only byte accsess alowed */ -#define CONFIG_SYS_SROM_SIZE 0x100 /* shadow of revision info is in nvram */ - -/* - * Serial devices - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK 24000000 -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_UART_BASE + 0) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_UART_BASE + 8) - -/* - * PCI stuff - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* pci plug-and-play */ -#define CONFIG_PCI_HOST PCI_HOST_AUTO -#undef CONFIG_PCI_SCAN_SHOW - -/* - * Optional Video console (graphic: SMI LynxEM) - */ -#define CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define VIDEO_KBD_INIT_FCT (simple_strtol (getenv("console"), NULL, 10)) -#define VIDEO_TSTC_FCT serial_stub_tstc -#define VIDEO_GETC_FCT serial_stub_getc - -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_VIDEO_LOGO -#define CONFIG_CONSOLE_EXTRA_INFO - -/* - * Initial BATs - */ -#if 1 - -#define CONFIG_SYS_IBAT0L 0 -#define CONFIG_SYS_IBAT0U 0 -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT1U - -#define CONFIG_SYS_IBAT1L 0 -#define CONFIG_SYS_IBAT1U 0 -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -#define CONFIG_SYS_IBAT2L 0 -#define CONFIG_SYS_IBAT2U 0 -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -#define CONFIG_SYS_IBAT3L 0 -#define CONFIG_SYS_IBAT3U 0 -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -#else - -/* SDRAM */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_RW) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT1U - -/* address range for flashes */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_FLASH_BASE | BATL_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_FLASH_BASE | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* ISA IO space */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_ISA_IO | BATL_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_ISA_IO | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* ISA memory space */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_ISA_MEM | BATL_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_ISA_MEM | BATU_BL_16M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -#endif - -/* - * Speed settings are board specific - */ -#define CONFIG_SYS_BUS_CLK 100000000 -#define CONFIG_SYS_CPU_CLK 400000000 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * L2CR setup -- make sure this is right for your board! - * look in include/74xx_7xx.h for the defines used here - */ - -#define CONFIG_SYS_L2 - -#if 1 -#define L2_INIT 0 /* cpu 750 CXe*/ -#else -#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ - L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) -#endif -#define L2_ENABLE (L2_INIT | L2CR_L2E) - -#define CONFIG_EEPRO100 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_EEPRO100_SROM_WRITE - -#endif /* __CONFIG_H */ diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h deleted file mode 100644 index 1861aa86d9..0000000000 --- a/include/configs/IceCube.h +++ /dev/null @@ -1,403 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_ICECUBE 1 /* ... on IceCube board */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFFF00000 boot high (standard configuration) - * 0xFF000000 boot low for 16 MiB boards - * 0xFF800000 boot low for 8 MiB boards - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI - -#if defined(CONFIG_PCI) -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 -#endif - -#define CONFIG_SYS_XLB_PIPELINING 1 - -#define CONFIG_MII 1 -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - -/* USB */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE -#define CONFIG_SYS_OHCI_BE_CONTROLLER -#undef CONFIG_SYS_USB_OHCI_BOARD_INIT -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_USB - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - - -#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT16 1 -#endif -#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */ -#if defined(CONFIG_LITE5200B) -# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B -#else -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT08 1 -#endif -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "bootfile=/tftpboot/MPC5200/uImage\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#if defined(CONFIG_LITE5200B) -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#else -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,5200@0" -#define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * Flash configuration - */ -#if defined(CONFIG_LITE5200B) -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_SIZE 0x01000000 -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x01760000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#if defined(CONFIG_SYS_LOWBOOT08) -# error CONFIG_SYS_LOWBOOT08 is incompatible with the Lite5200B -#endif -#if defined(CONFIG_SYS_LOWBOOT16) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x01060000) -#endif -#endif /* CONFIG_SYS_LOWBOOT */ -#else /* !CONFIG_LITE5200B (IceCube)*/ -#define CONFIG_SYS_FLASH_BASE 0xFF000000 -#define CONFIG_SYS_FLASH_SIZE 0x01000000 -#if !defined(CONFIG_SYS_LOWBOOT) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00740000 + 0x00800000) -#else /* CONFIG_SYS_LOWBOOT */ -#if defined(CONFIG_SYS_LOWBOOT08) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000 + 0x00800000) -#endif -#if defined(CONFIG_SYS_LOWBOOT16) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000) -#endif -#endif /* CONFIG_SYS_LOWBOOT */ -#endif /* CONFIG_LITE5200B */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */ - -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */ - -#if defined(CONFIG_LITE5200B) -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_CS1_START,CONFIG_SYS_CS0_START} -#endif - - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#if defined(CONFIG_LITE5200B) -#define CONFIG_ENV_SECT_SIZE 0x20000 -#else -#define CONFIG_ENV_SECT_SIZE 0x10000 -#endif -#define CONFIG_ENV_OVERWRITE 1 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - */ -#ifdef CONFIG_MPC5200_DDR -#define CONFIG_SYS_GPS_PORT_CONFIG 0x90000004 -#else -#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004 -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#if defined(CONFIG_LITE5200B) -#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_CS1_CFG 0x00047800 -#define CONFIG_SYS_CS0_START (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE) -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_CS0_START -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047800 -#else /* IceCube aka Lite5200 */ -#ifdef CONFIG_MPC5200_DDR - -#define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS1_START + CONFIG_SYS_CS1_SIZE) -#define CONFIG_SYS_BOOTCS_SIZE 0x00800000 -#define CONFIG_SYS_BOOTCS_CFG 0x00047801 -#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS1_SIZE 0x00800000 -#define CONFIG_SYS_CS1_CFG 0x00047800 - -#else /* !CONFIG_MPC5200_DDR */ - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047801 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#endif /* CONFIG_MPC5200_DDR */ -#endif /*CONFIG_LITE5200B */ - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#define CONFIG_ATAPI 1 - -#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h deleted file mode 100644 index aefde74fc5..0000000000 --- a/include/configs/MPC8360EMDS.h +++ /dev/null @@ -1,735 +0,0 @@ -/* - * Copyright (C) 2006,2011 Freescale Semiconductor, Inc. - * - * Dave Liu <daveliu@freescale.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ -#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ -#define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */ - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */ -#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */ - -/* - * System Clock Setup - */ -#ifdef CONFIG_CLKIN_33MHZ -#ifdef CONFIG_PCISLAVE -#define CONFIG_83XX_PCICLK 33330000 /* in HZ */ -#else -#define CONFIG_83XX_CLKIN 33330000 /* in Hz */ -#endif - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 33330000 -#endif - -#elif defined(CONFIG_CLKIN_66MHZ) -#ifdef CONFIG_PCISLAVE -#define CONFIG_83XX_PCICLK 66000000 /* in HZ */ -#else -#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ -#endif - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 66000000 -#endif -#else -#error Unknown oscillator frequency. -#endif - -/* - * Hardware Reset Configuration Word - */ -#ifdef CONFIG_CLKIN_33MHZ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_1X1 |\ - HRCWL_CSB_TO_CLKIN_8X1 |\ - HRCWL_VCO_1X2 |\ - HRCWL_CE_PLL_VCO_DIV_4 |\ - HRCWL_CE_PLL_DIV_1X1 |\ - HRCWL_CE_TO_PLL_1X15 |\ - HRCWL_CORE_TO_CSB_2X1) -#elif defined(CONFIG_CLKIN_66MHZ) -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_1X1 |\ - HRCWL_CSB_TO_CLKIN_4X1 |\ - HRCWL_VCO_1X2 |\ - HRCWL_CE_PLL_VCO_DIV_4 |\ - HRCWL_CE_PLL_DIV_1X1 |\ - HRCWL_CE_TO_PLL_1X6 |\ - HRCWL_CORE_TO_CSB_2X1) -#endif - -#ifdef CONFIG_PCISLAVE -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_AGENT |\ - HRCWH_PCI1_ARBITER_DISABLE |\ - HRCWH_PCICKDRV_DISABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0XFFF00100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT) -#else -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_HOST |\ - HRCWH_PCI1_ARBITER_ENABLE |\ - HRCWH_PCICKDRV_ENABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0X00000100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT) -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH 0x00000000 -#define CONFIG_SYS_SICRL 0x40000000 - -#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ -#define CONFIG_BOARD_EARLY_INIT_R - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE - /* + 256M */ -#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ - | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CONFIG_SYS_83XX_DDR_USES_CS0 - -#define CONFIG_DDR_ECC /* support DDR ECC function */ -#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ - -/* - * DDRCDR - DDR Control Driver Register - */ -#define CONFIG_SYS_DDRCDR_VALUE 0x80080001 - -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#if defined(CONFIG_SPD_EEPROM) -/* - * Determine DDR configuration from I2C interface. - */ -#define SPD_EEPROM_ADDRESS 0x52 /* DDR SODIMM */ -#else -/* - * Manually set up DDR parameters - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#if defined(CONFIG_DDR_II) -#define CONFIG_SYS_DDRCDR 0x80080001 -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80330102 -#define CONFIG_SYS_DDR_TIMING_0 0x00220802 -#define CONFIG_SYS_DDR_TIMING_1 0x38357322 -#define CONFIG_SYS_DDR_TIMING_2 0x2f9048c8 -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_CLK_CNTL 0x02000000 -#define CONFIG_SYS_DDR_MODE 0x47d00432 -#define CONFIG_SYS_DDR_MODE2 0x8000c000 -#define CONFIG_SYS_DDR_INTERVAL 0x03cf0080 -#define CONFIG_SYS_DDR_SDRAM_CFG 0x43000000 -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#else -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_9) -#define CONFIG_SYS_DDR_CS1_CONFIG CONFIG_SYS_DDR_CS0_CONFIG -#define CONFIG_SYS_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */ -#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* may need tuning */ -#define CONFIG_SYS_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */ -#define CONFIG_SYS_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */ -#define CONFIG_SYS_DDR_INTERVAL 0x045b0100 /* page mode */ -#endif -#endif - -/* - * Memory test - */ -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * The reserved memory - */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CONFIG_SYS_FLASH_SIZE 32 /* max FLASH size is 32M */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - - /* Window base at flash base */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM - -/* - * BCSR on the Local Bus - */ -#define CONFIG_SYS_BCSR 0xF8000000 - /* Access window base at BCSR base */ -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_64KB) - -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ - | BR_PS_8 \ - | BR_MS_GPCM \ - | BR_V) -#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xFFFFE9F7 */ - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* SDRAM base address */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -#define CONFIG_SYS_LB_SDRAM /* if board has SRDAM on local bus */ - -#ifdef CONFIG_SYS_LB_SDRAM -#define CONFIG_SYS_LBLAWBAR2 0 -#define CONFIG_SYS_LBLAWAR2 (LBLAWAR_EN | LBLAWAR_64MB) - -/*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */ -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * - * For BR2, need: - * Base address = BR[0:16] = dynamic - * port size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * xxxx xxxx xxxx xxxx x001 1000 0110 0001 = 00001861 - */ - -/* Port size=32bit, MSEL=DRAM */ -#define CONFIG_SYS_BR2 (BR_PS_32 | BR_MS_SDRAM | BR_V) /* 0xF0001861 */ - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 - */ - -#define CONFIG_SYS_OR2 (MEG_TO_AM(CONFIG_SYS_LBC_SDRAM_SIZE) \ - | OR_SDRAM_XAM \ - | ((9 - OR_SDRAM_MIN_COLS) << OR_SDRAM_COLS_SHIFT) \ - | ((13 - OR_SDRAM_MIN_ROWS) << OR_SDRAM_ROWS_SHIFT) \ - | OR_SDRAM_EAD) - /* 0xFC006901 */ - - /* LB sdram refresh timer, about 6us */ -#define CONFIG_SYS_LBC_LSRT 0x32000000 - /* LB refresh timer prescal, 266MHz/32 */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 - -#define CONFIG_SYS_LBC_LSDMR_COMMON 0x0063b723 - -/* - * SDRAM Controller configuration sequence. - */ -#define CONFIG_SYS_LBC_LSDMR_1 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_PCHALL) -#define CONFIG_SYS_LBC_LSDMR_2 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_3 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_ARFRSH) -#define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW) -#define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL) - -#endif - -/* - * Windows to access Platform I/O Boards (PIB) via local bus - */ -#define CONFIG_SYS_PIB_BASE 0xF8008000 -#define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024) - -/* [RFC] This LBLAW only covers the 2nd window (CS5) */ -#define CONFIG_SYS_LBLAWBAR3_PRELIM \ - CONFIG_SYS_PIB_BASE + CONFIG_SYS_PIB_WINDOW_SIZE -#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) - -/* - * CS4 on Local Bus, to PIB - */ - /* CS4 base address at 0xf8008000 */ -#define CONFIG_SYS_BR4_PRELIM (CONFIG_SYS_PIB_BASE \ - | BR_PS_8 \ - | BR_MS_GPCM \ - | BR_V) - /* 0xF8008801 */ -#define CONFIG_SYS_OR4_PRELIM (OR_AM_32KB \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xffffe9f7 */ - -/* - * CS5 on Local Bus, to PIB - */ - /* CS5 base address at 0xf8010000 */ -#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_PIB_BASE + \ - CONFIG_SYS_PIB_WINDOW_SIZE) \ - | BR_PS_8 \ - | BR_MS_GPCM \ - | BR_V) - /* 0xF8010801 */ -#define CONFIG_SYS_OR5_PRELIM (CONFIG_SYS_PIB_BASE \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xffffe9f7 */ - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } - -/* - * Config on-board RTC - */ -#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 -#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 - - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_83XX_PCI_STREAMING - -#undef CONFIG_EEPRO100 -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -#endif /* CONFIG_PCI */ - - -#define CONFIG_HWCONFIG 1 - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" -#define CONFIG_PHY_MODE_NEED_CHANGE - -#define CONFIG_UEC_ETH1 /* GETH1 */ - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 -#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 0 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 -#endif - -#define CONFIG_UEC_ETH2 /* GETH2 */ - -#ifdef CONFIG_UEC_ETH2 -#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ -#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4 -#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH -#define CONFIG_SYS_UEC2_PHY_ADDR 1 -#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID -#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x20000 - #define CONFIG_ENV_SIZE 0x2000 -#else - #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_SDRAM - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_SYS_RAMBOOT) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS -#endif - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - - /* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ - -/* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ -#define CONFIG_BAT_RW - -/* DDR/LBC SDRAM: cacheable */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* IMMRBAR & PCI IO: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ - | BATU_BL_4M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* BCSR: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \ - | BATU_BL_128K \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ - | BATU_BL_32M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* DDR/LBC SDRAM next 256M: cacheable */ -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM_BASE2 \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM_BASE2 \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \ - | BATU_BL_128K \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U - -#ifdef CONFIG_PCI -/* PCI MEM space: cacheable */ -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -/* PCI MMIO space: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#else -#define CONFIG_SYS_IBAT6L (0) -#define CONFIG_SYS_IBAT6U (0) -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - -#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=ramfs.83xx\0" \ - "fdtaddr=780000\0" \ - "fdtfile=mpc836x_mds.dtb\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h deleted file mode 100644 index 1b8bad179b..0000000000 --- a/include/configs/MPC8360ERDK.h +++ /dev/null @@ -1,620 +0,0 @@ -/* - * Copyright (C) 2006 Freescale Semiconductor, Inc. - * Dave Liu <daveliu@freescale.com> - * - * Copyright (C) 2007 Logic Product Development, Inc. - * Peter Barada <peterb@logicpd.com> - * - * Copyright (C) 2007 MontaVista Software, Inc. - * Anton Vorontsov <avorontsov@ru.mvista.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ -#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ -#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */ - -#define CONFIG_SYS_TEXT_BASE 0xFF800000 - -/* - * System Clock Setup - */ -#ifdef CONFIG_CLKIN_33MHZ -#define CONFIG_83XX_CLKIN 33333333 -#define CONFIG_SYS_CLK_FREQ 33333333 -#define CONFIG_PCI_33M 1 -#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1 -#else -#define CONFIG_83XX_CLKIN 66000000 -#define CONFIG_SYS_CLK_FREQ 66000000 -#define CONFIG_PCI_66M 1 -#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1 -#endif /* CONFIG_CLKIN_33MHZ */ - -/* - * Hardware Reset Configuration Word - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_1X1 |\ - HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\ - HRCWL_CORE_TO_CSB_2X1 |\ - HRCWL_CE_TO_PLL_1X15) - -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_HOST |\ - HRCWH_PCI1_ARBITER_ENABLE |\ - HRCWH_PCICKDRV_ENABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0X00000100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_SECONDARY_DDR_DISABLE |\ - HRCWH_BIG_ENDIAN |\ - HRCWH_LALE_EARLY) - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH 0x00000000 -#define CONFIG_SYS_SICRL 0x40000000 - -#define CONFIG_BOARD_EARLY_INIT_R - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ - | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) - -#define CONFIG_SYS_83XX_DDR_USES_CS0 - -#define CONFIG_DDR_ECC /* support DDR ECC function */ -#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ - -/* - * DDRCDR - DDR Control Driver Register - */ -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \ - | DDRCDR_ODT \ - | DDRCDR_Q_DRN) - /* 0x80080001 */ - -#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ - -/* - * Manually set up DDR parameters - */ -#define CONFIG_DDR_II -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10 \ - | CSCONFIG_ODT_WR_ONLY_CURRENT) -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_ECC_EN) -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 -#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) -#define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \ - | (1115 << SDRAM_INTERVAL_REFINT_SHIFT)) -#define CONFIG_SYS_DDR_MODE 0x47800432 -#define CONFIG_SYS_DDR_MODE2 0x8000c000 - -#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ - (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ - (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ - (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ - (0 << TIMING_CFG0_WWT_SHIFT) | \ - (0 << TIMING_CFG0_RRT_SHIFT) | \ - (0 << TIMING_CFG0_WRT_SHIFT) | \ - (0 << TIMING_CFG0_RWT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \ - (2 << TIMING_CFG1_WRTORD_SHIFT) | \ - (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ - (3 << TIMING_CFG1_WRREC_SHIFT) | \ - (10 << TIMING_CFG1_REFREC_SHIFT) | \ - (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ - (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ - (3 << TIMING_CFG1_PRETOACT_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ - (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \ - (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ - (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ - (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ - (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ - (0 << TIMING_CFG2_CPO_SHIFT)) - -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -/* - * Memory test - */ -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* FLASH base address */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use intel Flash protection. */ - - /* Window base at flash base */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_UPM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM - -/* - * NAND flash on the local bus - */ -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_CMD_NAND 1 -#define CONFIG_NAND_FSL_UPM 1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_MTD_NAND_VERIFY_WRITE - -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE -/* - * [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB - * ... What's correct? - */ -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) - -/* Port size 8 bit, UPMA */ -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \ - | BR_PS_8 \ - | BR_MS_UPMA \ - | BR_V) - /* 0x60000881 */ -#define CONFIG_SYS_OR1_PRELIM (OR_AM_64MB | OR_UPM_EAD) - /* 0xFC000001 */ - -/* - * Fujitsu MB86277 (MINT) graphics controller - */ -#define CONFIG_SYS_VIDEO_BASE 0x70000000 - -#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VIDEO_BASE -#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) - -/* Port size 32 bit, UPMB */ -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VIDEO_BASE \ - | BR_PS_32 \ - | BR_MS_UPMB \ - | BR_V) - /* 0x000018a1 */ -#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB | OR_UPM_EAD) - /* 0xFC000001 */ - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_PCI - -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0xE0300000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -#endif /* CONFIG_PCI */ - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* GETH1 */ - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 -#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 2 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 -#endif - -#define CONFIG_UEC_ETH2 /* GETH2 */ - -#ifdef CONFIG_UEC_ETH2 -#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ -#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE -#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4 -#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH -#define CONFIG_SYS_UEC2_PHY_ADDR 4 -#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID -#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 -#endif - -/* - * Environment - */ - -#ifndef CONFIG_SYS_RAMBOOT -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ -#define CONFIG_ENV_SIZE 0x20000 -#else /* CONFIG_SYS_RAMBOOT */ -#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ -#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif /* CONFIG_SYS_RAMBOOT */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - -#if defined(CONFIG_SYS_RAMBOOT) -#undef CONFIG_CMD_SAVEENV -#undef CONFIG_CMD_LOADS -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else - #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - - /* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ - -/* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* DDR: cache cacheable */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* IMMRBAR & PCI IO: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ - | BATU_BL_4M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* NAND: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_NAND_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_NAND_BASE \ - | BATU_BL_64M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ - | BATU_BL_32M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR \ - | BATL_PP_RW) -#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \ - | BATU_BL_128K \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U - -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_VIDEO_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_VIDEO_BASE \ - | BATU_BL_64M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U - -#ifdef CONFIG_PCI -/* PCI MEM space: cacheable */ -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -/* PCI MMIO space: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#else /* CONFIG_PCI */ -#define CONFIG_SYS_IBAT6L (0) -#define CONFIG_SYS_IBAT6U (0) -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#define CONFIG_HAS_ETH3 -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADADDR a00000 -#define CONFIG_HOSTNAME mpc8360erdk -#define CONFIG_BOOTFILE "uImage" - -#define CONFIG_ROOTPATH "/nfsroot/" - -#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "loadaddr=a00000\0" \ - "fdtaddr=900000\0" \ - "fdtfile=mpc836x_rdk.dtb\0" \ - "fsfile=fs\0" \ - "ubootfile=u-boot.bin\0" \ - "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\ - "-(rootfs)\0" \ - "setbootargs=setenv bootargs console=$consoledev,$baudrate " \ - "$mtdparts panic=1\0" \ - "adddhcpargs=setenv bootargs $bootargs ip=on\0" \ - "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:" \ - "$gatewayip:$netmask:$hostname:$netdev:off " \ - "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \ - "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 " \ - "rootfstype=jffs2 rw\0" \ - "tftp_get_uboot=tftp 100000 $ubootfile\0" \ - "tftp_get_kernel=tftp $loadaddr $bootfile\0" \ - "tftp_get_dtb=tftp $fdtaddr $fdtfile\0" \ - "tftp_get_fs=tftp c00000 $fsfile\0" \ - "nand_erase_kernel=nand erase 0 400000\0" \ - "nand_erase_dtb=nand erase 400000 20000\0" \ - "nand_erase_fs=nand erase 420000 3be0000\0" \ - "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0" \ - "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0" \ - "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0" \ - "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0" \ - "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0" \ - "nor_reflash=protect off ff800000 ff87ffff ; " \ - "erase ff800000 ff87ffff ; " \ - "cp.b 100000 ff800000 $filesize\0" \ - "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel " \ - "nand_write_kernel\0" \ - "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\ - "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \ - "nand_reflash=run nand_reflash_kernel nand_reflash_dtb " \ - "nand_reflash_fs\0" \ - "boot_m=bootm $loadaddr - $fdtaddr\0" \ - "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\ - "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\ - "boot_m\0" \ - "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\ - "boot_m\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run dhcpboot" - -#endif /* __CONFIG_H */ diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 8ed0f7c21a..19e0e30eef 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -15,6 +15,8 @@ #define CONFIG_E300 1 /* E300 family */ #define CONFIG_MPC837x 1 /* MPC837x CPU specific */ #define CONFIG_MPC837XERDB 1 +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_SYS_GENERIC_BOARD #define CONFIG_SYS_TEXT_BASE 0xFE000000 diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h deleted file mode 100644 index c75638abda..0000000000 --- a/include/configs/P1_P2_RDB.h +++ /dev/null @@ -1,808 +0,0 @@ -/* - * Copyright 2009-2011 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * P1 P2 RDB board configuration file - * This file is intended to address a set of Low End and Ultra Low End - * Freescale SOCs of QorIQ series(RDB platforms). - * Currently only P2020RDB - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#ifdef CONFIG_36BIT -#define CONFIG_PHYS_64BIT -#endif - -#ifdef CONFIG_P1011RDB -#define CONFIG_P1011 -#define CONFIG_SYS_L2_SIZE (256 << 10) -#endif -#ifdef CONFIG_P1020RDB -#define CONFIG_P1020 -#define CONFIG_SYS_L2_SIZE (256 << 10) -#endif -#ifdef CONFIG_P2010RDB -#define CONFIG_P2010 -#define CONFIG_SYS_L2_SIZE (512 << 10) -#endif -#ifdef CONFIG_P2020RDB -#define CONFIG_P2020 -#define CONFIG_SYS_L2_SIZE (512 << 10) -#endif - -#ifdef CONFIG_SDCARD -#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT -#define CONFIG_SPL_ENV_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_MMC_SUPPORT -#define CONFIG_SPL_MMC_MINIMAL -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SYS_TEXT_BASE 0x11001000 -#define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_PAD_TO 0x20000 -#define CONFIG_SPL_MAX_SIZE (128 * 1024) -#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_MMC_U_BOOT_DST (0x11000000) -#define CONFIG_SYS_MMC_U_BOOT_START (0x11000000) -#define CONFIG_SYS_MMC_U_BOOT_OFFS (129 << 10) -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" -#define CONFIG_SPL_MMC_BOOT -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_COMMON_INIT_DDR -#endif -#endif - -#ifdef CONFIG_SPIFLASH -#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT -#define CONFIG_SPL_ENV_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_SPI_SUPPORT -#define CONFIG_SPL_SPI_FLASH_SUPPORT -#define CONFIG_SPL_SPI_FLASH_MINIMAL -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SYS_TEXT_BASE 0x11001000 -#define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_PAD_TO 0x20000 -#define CONFIG_SPL_MAX_SIZE (128 * 1024) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x11000000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x11000000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (128 << 10) -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" -#define CONFIG_SPL_SPI_BOOT -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SPL_COMMON_INIT_DDR -#endif -#endif - -#ifdef CONFIG_NAND -#ifdef CONFIG_TPL_BUILD -#define CONFIG_SPL_NAND_BOOT -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_ENV_SUPPORT -#define CONFIG_SPL_NAND_INIT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT -#define CONFIG_SPL_COMMON_INIT_DDR -#define CONFIG_SPL_MAX_SIZE (128 << 10) -#define CONFIG_SPL_TEXT_BASE 0xf8f81000 -#define CONFIG_SYS_MPC85XX_NO_RESETVEC -#define CONFIG_SYS_NAND_U_BOOT_SIZE (832 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000) -#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000) -#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10) -#elif defined(CONFIG_SPL_BUILD) -#define CONFIG_SPL_INIT_MINIMAL -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_FLUSH_IMAGE -#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" -#define CONFIG_SPL_TEXT_BASE 0xff800000 -#define CONFIG_SPL_MAX_SIZE 4096 -#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0xf8f80000 -#define CONFIG_SYS_NAND_U_BOOT_START 0xf8f80000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10) -#endif /* not CONFIG_TPL_BUILD */ - -#define CONFIG_SPL_PAD_TO 0x20000 -#define CONFIG_TPL_PAD_TO 0x20000 -#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" -#define CONFIG_SYS_TEXT_BASE 0x11001000 -#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" -#endif - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xeff40000 -#endif - -#ifndef CONFIG_RESET_VECTOR_ADDRESS -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc -#endif - -#ifndef CONFIG_SYS_MONITOR_BASE -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE -#else -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif -#endif - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */ - -#define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#if defined(CONFIG_PCI) -#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ -#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ -#endif /* #if defined(CONFIG_PCI) */ -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_PCI) -#define CONFIG_E1000 1 /* E1000 pci Ethernet card*/ -#endif - -#ifndef __ASSEMBLY__ -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif -#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1_P2 RDB */ -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /*sysclk for P1_P2 RDB */ - -#if defined(CONFIG_P2020) || defined(CONFIG_P1020) -#define CONFIG_MP -#endif - -#define CONFIG_HWCONFIG - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ - -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP 1 -#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ -#endif - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x1fffffff -#define CONFIG_PANIC_HANG /* do not reset board on panic */ - -/* - * Config the L2 Cache as L2 SRAM -*/ -#if defined(CONFIG_SPL_BUILD) -#if defined(CONFIG_SDCARD) || defined(CONFIG_SPIFLASH) -#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 -#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR -#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 112 * 1024) -#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 116 * 1024) -#define CONFIG_SPL_RELOC_STACK_SIZE (32 << 10) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 148 * 1024) -#if defined(CONFIG_P2020RDB) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (364 << 10) -#else -#define CONFIG_SPL_RELOC_MALLOC_SIZE (108 << 10) -#endif -#elif defined(CONFIG_NAND) -#ifdef CONFIG_TPL_BUILD -#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 -#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR -#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -#define CONFIG_SPL_RELOC_TEXT_BASE 0xf8f81000 -#define CONFIG_SPL_RELOC_STACK (CONFIG_SYS_INIT_L2_ADDR + 192 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SYS_INIT_L2_ADDR + 208 * 1024) -#define CONFIG_SPL_RELOC_MALLOC_SIZE (48 << 10) -#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L2_ADDR + 176 * 1024) -#else -#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 -#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR -#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) -#define CONFIG_SPL_RELOC_TEXT_BASE (CONFIG_SYS_INIT_L2_END - 0x2000) -#define CONFIG_SPL_RELOC_STACK ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF) -#endif /* CONFIG_TPL_BUILD */ -#endif -#endif - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE -#endif - -/* DDR Setup */ -#define CONFIG_SYS_FSL_DDR2 -#undef CONFIG_FSL_DDR_INTERACTIVE -#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#if defined(CONFIG_P1011RDB) || defined(CONFIG_P1020RDB) -/* - * P1020 and it's derivatives support max 32bit DDR width - * So Reduce available DDR size -*/ -#define CONFIG_SYS_SDRAM_SIZE 512 -#else -#define CONFIG_SYS_SDRAM_SIZE 1024 -#endif -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 1 - -#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d -#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 -#define CONFIG_SYS_DDR_SBE 0x00FF0000 - -/* - * Memory map - * - * 0x0000_0000 0x3fff_ffff DDR 1G cacheablen - * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable - * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable - * - * Localbus cacheable (TBD) - * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable - * - * Localbus non-cacheable - * 0xef00_0000 0xefff_ffff FLASH 16M non-cacheable - * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable - * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable - * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 - * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable - */ - -/* - * Local Bus Definitions - */ -#define CONFIG_SYS_FLASH_BASE 0xef000000 /* start of FLASH 16M */ - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_FLASH_BASE_PHYS 0xfef000000ull -#else -#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE -#endif - -#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ - BR_PS_16 | BR_V) -#define CONFIG_FLASH_OR_PRELIM 0xff000ff7 - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 - -#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ -#define CONFIG_MISC_INIT_R -#define CONFIG_HWCONFIG - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR -/* The assembler doesn't like typecast */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ - ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ - CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) -#else -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ - - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/ - -#define CONFIG_SYS_NAND_BASE 0xff800000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_NAND_BASE_PHYS 0xfff800000ull -#else -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE -#endif - -#define CONFIG_CMD_NAND -#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE} -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_MTD_NAND_VERIFY_WRITE -#define CONFIG_NAND_FSL_ELBC 1 -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) - -/* NAND flash config */ -#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ - | BR_PS_8 /* Port Size = 8 bit */ \ - | BR_MS_FCM /* MSEL = FCM */ \ - | BR_V) /* valid */ - -#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \ - | OR_FCM_CSCT \ - | OR_FCM_CST \ - | OR_FCM_CHT \ - | OR_FCM_SCY_1 \ - | OR_FCM_TRLX \ - | OR_FCM_EHTR) - -#ifdef CONFIG_NAND -#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ -#define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ -#define CONFIG_SYS_OR1_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#else -#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ -#endif - -#define CONFIG_SYS_VSC7385_BASE 0xffb00000 - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_VSC7385_BASE_PHYS 0xfffb00000ull -#else -#define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE -#endif - -#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_VSC7385_BASE) \ - | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ - OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \ - OR_GPCM_EHTR | OR_GPCM_EAD) - -/* Serial Port - controlled on board with jumper J8 - * open - index 2 - * shorted - index 1 - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) -#define CONFIG_NS16550_MIN_FUNCTIONS -#endif - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Pass open firmware flat tree - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* new uImage format support */ -#define CONFIG_FIT 1 -#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } - -/* - * I2C2 EEPROM - */ -#define CONFIG_ID_EEPROM -#ifdef CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#endif -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_BUS_NUM 1 - -#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 - -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_RTC_DS1337_NOOSC -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* eSPI - Enhanced SPI */ -#define CONFIG_FSL_ESPI -#define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_SPANSION -#define CONFIG_CMD_SF -#define CONFIG_SF_DEFAULT_SPEED 10000000 -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ - -#if defined(CONFIG_PCI) -/* controller 2, Slot 2, tgtid 2, Base address 9000 */ -#define CONFIG_SYS_PCIE2_NAME "Slot 1" -#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull -#else -#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 -#endif -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull -#else -#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 -#endif -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ - -/* controller 1, Slot 1, tgtid 1, Base address a000 */ -#define CONFIG_SYS_PCIE1_NAME "Slot 2" -#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull -#else -#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 -#endif -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull -#else -#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 -#endif -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP -#undef CONFIG_RTL8139 - -#ifdef CONFIG_RTL8139 -/* This macro is used by RTL8139 but not defined in PPC architecture */ -#define KSEG1ADDR(x) (x) -#define _IO_BASE 0x00000000 -#endif - - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_DOS_PARTITION - -#endif /* CONFIG_PCI */ - - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" - -#define TSEC1_PHY_ADDR 2 -#define TSEC2_PHY_ADDR 0 -#define TSEC3_PHY_ADDR 1 - -#define CONFIG_VSC7385_ENET - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 - -/* Vitesse 7385 */ - -#ifdef CONFIG_VSC7385_ENET -/* The size of the VSC7385 firmware image */ -#define CONFIG_VSC7385_IMAGE_SIZE 8192 -#endif - -#define CONFIG_ETHPRIME "eTSEC1" - -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#ifdef CONFIG_SPIFLASH -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 10000000 -#define CONFIG_ENV_SPI_MODE 0 -#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ -#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) -#elif defined(CONFIG_SDCARD) -#define CONFIG_ENV_IS_IN_MMC -#define CONFIG_FSL_FIXED_MMC_LOCATION -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_SYS_MMC_ENV_DEV 0 -#define CONFIG_ENV_OFFSET (512 * 0x800) -#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) -#elif defined(CONFIG_NAND) -#ifdef CONFIG_TPL_BUILD -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10)) -#else -#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#endif -#define CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_OFFSET (1024 * 1024) -#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) -#elif defined(CONFIG_SYS_RAMBOOT) -#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#else -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ -#endif - - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_SETEXPR -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_MMC 1 - -#ifdef CONFIG_MMC -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_CMD_MMC -#define CONFIG_DOS_PARTITION -#define CONFIG_FSL_ESDHC -#define CONFIG_GENERIC_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#ifdef CONFIG_P2020 -#define CONFIG_SYS_FSL_ESDHC_USE_PIO /* P2020 eSDHC DMA is not functional*/ -#endif -#endif - -#define CONFIG_HAS_FSL_DR_USB - -#if defined(CONFIG_HAS_FSL_DR_USB) -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI -#define CONFIG_CMD_USB -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_USB_EHCI_FSL -#define CONFIG_USB_STORAGE -#endif -#endif - -#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_DOS_PARTITION -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20)/* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#endif - -#define CONFIG_HOSTNAME P2020RDB -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */ - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 - -#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ - "loadaddr=1000000\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=rootfs.ext2.gz.uboot\0" \ - "fdtaddr=c00000\0" \ - "fdtfile=p2020rdb.dtb\0" \ - "bdev=sda1\0" \ - "jffs2nor=mtdblock3\0" \ - "norbootaddr=ef080000\0" \ - "norfdtaddr=ef040000\0" \ - "jffs2nand=mtdblock9\0" \ - "nandbootaddr=100000\0" \ - "nandfdtaddr=80000\0" \ - "nandimgsize=400000\0" \ - "nandfdtsize=80000\0" \ - "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ - "vscfw_addr=ef000000\0" \ - "othbootargs=ramdisk_size=600000\0" \ - "usbfatboot=setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "usb start;" \ - "fatload usb 0:2 $loadaddr $bootfile;" \ - "fatload usb 0:2 $fdtaddr $fdtfile;" \ - "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ - "usbext2boot=setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "usb start;" \ - "ext2load usb 0:4 $loadaddr $bootfile;" \ - "ext2load usb 0:4 $fdtaddr $fdtfile;" \ - "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ - "norboot=setenv bootargs root=/dev/$jffs2nor rw " \ - "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ - "bootm $norbootaddr - $norfdtaddr\0" \ - "nandboot=setenv bootargs root=/dev/$jffs2nand rw rootfstype=jffs2 " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "nand read 2000000 $nandbootaddr $nandimgsize;" \ - "nand read 3000000 $nandfdtaddr $nandfdtsize;" \ - "bootm 2000000 - 3000000;\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_HDBOOT \ - "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "usb start;" \ - "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ - "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT - -#endif /* __CONFIG_H */ diff --git a/include/configs/P2020COME.h b/include/configs/P2020COME.h deleted file mode 100644 index d414b84dd2..0000000000 --- a/include/configs/P2020COME.h +++ /dev/null @@ -1,547 +0,0 @@ -/* - * Copyright 2009-2010,2012 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* The P2020COME board is only booted via the Freescale On-Chip ROM */ -#define CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_EXTRA_ENV_RELOC - -#define CONFIG_SYS_TEXT_BASE 0xf8f80000 -#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc - -#ifdef CONFIG_SDCARD -#define CONFIG_RAMBOOT_SDCARD 1 -#endif - -#ifdef CONFIG_SPIFLASH -#define CONFIG_RAMBOOT_SPIFLASH 1 -#endif - -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_P2020 1 -#define CONFIG_P2020COME 1 -#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */ -#define CONFIG_MP - -#define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#if defined(CONFIG_PCI) -#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */ -#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */ -#define CONFIG_PCIE3 1 /* PCIE controller 3 (slot 3) */ - -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ -#endif /* #if defined(CONFIG_PCI) */ -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_PCI) -#define CONFIG_E1000 1 /* E1000 pci Ethernet card */ -#endif - -#ifndef __ASSEMBLY__ -extern unsigned long get_board_ddr_clk(unsigned long dummy); -extern unsigned long get_board_sys_clk(unsigned long dummy); -#endif - -/* - * For P2020COME DDRCLK and SYSCLK are from the same oscillator - * For DA phase the SYSCLK is 66MHz - * For EA phase the SYSCLK is 100MHz - */ -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) - -#define CONFIG_HWCONFIG - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch prediction */ - -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ - -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP 1 -#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ -#endif - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x1fffffff -#define CONFIG_PANIC_HANG /* do not reset board on panic */ - - /* - * Config the L2 Cache as L2 SRAM - */ -#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull -#else -#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR -#endif -#define CONFIG_SYS_L2_SIZE (512 << 10) -#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR \ - + CONFIG_SYS_L2_SIZE) - -#define CONFIG_SYS_CCSRBAR 0xffe00000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SYS_FSL_DDR3 -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#define CONFIG_DDR_SPD - -#define CONFIG_DDR_ECC -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_MEM_INIT_VALUE 0xdeadbeef - -#define CONFIG_SYS_SDRAM_SIZE 2048ULL /* DDR size on P2020COME */ -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d -#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 -#define CONFIG_SYS_DDR_SBE 0x00ff0000 - -#define CONFIG_SYS_SPD_BUS_NUM 1 -#define SPD_EEPROM_ADDRESS 0x53 - -/* - * Memory map - * - * 0x0000_0000 0x7fff_ffff DDR3 2G Cacheable - * 0x8000_0000 0x9fff_ffff PCI Express 3 Mem 1G non-cacheable - * 0xa000_0000 0xbfff_ffff PCI Express 2 Mem 1G non-cacheable - * 0xc000_0000 0xdfff_ffff PCI Express 1 Mem 1G non-cacheable - * 0xffc1_0000 0xffc1_ffff PCI Express 3 IO 64K non-cacheable - * 0xffc2_0000 0xffc2_ffff PCI Express 2 IO 64K non-cacheable - * 0xffc3_0000 0xffc3_ffff PCI Express 1 IO 64K non-cacheable - * - * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 - * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable - */ - -/* - * Local Bus Definitions - */ - -/* There is no NOR Flash on P2020COME */ -#define CONFIG_SYS_NO_FLASH - -#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ -#define CONFIG_HWCONFIG - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR -/* the assembler doesn't like typecast */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ - ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ - CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) -#else -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \ - - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) - -/* Serial Port - controlled on board with jumper J8 - * open - index 2 - * shorted - index 1 - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Pass open firmware flat tree - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* new uImage format support */ -#define CONFIG_FIT 1 -#define CONFIG_FIT_VERBOSE 1 - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } - -/* - * I2C2 EEPROM - */ -#define CONFIG_ID_EEPROM -#ifdef CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#endif -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_I2C_EEPROM_ADDR2 0x18 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_BUS_NUM 0 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * eSPI - Enhanced SPI - */ -#define CONFIG_FSL_ESPI -#define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_STMICRO -#define CONFIG_CMD_SF -#define CONFIG_SF_DEFAULT_SPEED 10000000 -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#if defined(CONFIG_PCI) - -/* controller 3, Slot 3, tgtid 3, Base address 8000 */ -#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc10000 -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc10000 -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ - -/* controller 2, Slot 2, tgtid 2, Base address 9000 */ -#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000 -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ - -/* controller 1, Slot 1, tgtid 1, Base address a000 */ -#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 -#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000 -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP -#undef CONFIG_RTL8139 - -#ifdef CONFIG_RTL8139 -/* This macro is used by RTL8139 but not defined in PPC architecture */ -#define KSEG1ADDR(x) (x) -#define _IO_BASE 0x00000000 -#endif - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_DOS_PARTITION - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" - -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 2 -#define TSEC3_PHY_ADDR 1 - -#undef CONFIG_VSC7385_ENET - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 - -#define CONFIG_ETHPRIME "eTSEC1" - -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#if defined(CONFIG_RAMBOOT_SDCARD) - #define CONFIG_ENV_IS_IN_MMC 1 - #define CONFIG_FSL_FIXED_MMC_LOCATION - #define CONFIG_ENV_SIZE 0x2000 - #define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_RAMBOOT_SPIFLASH) - #define CONFIG_ENV_IS_IN_SPI_FLASH - #define CONFIG_ENV_SPI_BUS 0 - #define CONFIG_ENV_SPI_CS 0 - #define CONFIG_ENV_SPI_MAX_HZ 10000000 - #define CONFIG_ENV_SPI_MODE 0 - #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ - #define CONFIG_ENV_SECT_SIZE 0x10000 - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_SETEXPR -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_MMC 1 - -#ifdef CONFIG_MMC -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_CMD_MMC -#define CONFIG_DOS_PARTITION -#define CONFIG_FSL_ESDHC -#define CONFIG_GENERIC_MMC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT -#endif /* CONFIG_MMC */ - -#define CONFIG_HAS_FSL_DR_USB -#ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI -#define CONFIG_CMD_USB -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#define CONFIG_USB_EHCI_FSL -#define CONFIG_USB_STORAGE -#endif -#endif - -#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_DOS_PARTITION -#endif - -/* Misc Extra Settings */ -#define CONFIG_CMD_DHCP 1 - -#define CONFIG_CMD_DATE 1 -#define CONFIG_RTC_M41T62 1 -#define CONFIG_SYS_RTC_BUS_NUM 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) -#define CONFIG_SYS_BOOTM_LEN (64 << 20) - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#define CONFIG_HAS_ETH3 -#endif - -#define CONFIG_HOSTNAME unknown -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH u-boot.bin - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 - -#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "hwconfig=fsl_ddr:ecc=on\0" \ - "bootcmd=run sdboot\0" \ - "sdboot=setenv bootargs root=/dev/mmcblk0p2 rw " \ - "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\ - "$othbootargs; mmcinfo; " \ - "ext2load mmc 0:2 $loadaddr /boot/$bootfile; " \ - "ext2load mmc 0:2 $fdtaddr /boot/$fdtfile; " \ - "bootm $loadaddr - $fdtaddr\0" \ - "sdfatboot=setenv bootargs root=/dev/ram rw " \ - "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\ - "$othbootargs; mmcinfo; " \ - "fatload mmc 0:1 $loadaddr $bootfile; " \ - "fatload mmc 0:1 $fdtaddr $fdtfile; " \ - "fatload mmc 0:1 $ramdiskaddr $ramdiskfile; " \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ - "usbboot=setenv bootargs root=/dev/sda1 rw " \ - "rootdelay=$rootdelaysecond console=$consoledev,$baudrate "\ - "$othbootargs; " \ - "usb start; " \ - "ext2load usb 0:1 $loadaddr /boot/$bootfile; " \ - "ext2load usb 0:1 $fdtaddr /boot/$fdtfile; " \ - "bootm $loadaddr - $fdtaddr\0" \ - "usbfatboot=setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "usb start; " \ - "fatload usb 0:2 $loadaddr $bootfile; " \ - "fatload usb 0:2 $fdtaddr $fdtfile; " \ - "fatload usb 0:2 $ramdiskaddr $ramdiskfile; " \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ - "usbext2boot=setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs; " \ - "usb start; " \ - "ext2load usb 0:4 $loadaddr $bootfile; " \ - "ext2load usb 0:4 $fdtaddr $fdtfile; " \ - "ext2load usb 0:4 $ramdiskaddr $ramdiskfile; " \ - "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \ - "upgradespi=sf probe 0; " \ - "setenv startaddr 0; " \ - "setenv erasesize a0000; " \ - "tftp 1000000 $tftppath/$uboot_spi; " \ - "sf erase $startaddr $erasesize; " \ - "sf write 1000000 $startaddr $filesize; " \ - "sf erase 100000 120000\0" \ - "clearspienv=sf probe 0;sf erase 100000 20000\0" \ - "othbootargs=ramdisk_size=700000 cache-sram-size=0x10000\0" \ - "netdev=eth0\0" \ - "rootdelaysecond=15\0" \ - "uboot_nor=u-boot-nor.bin\0" \ - "uboot_spi=u-boot-p2020.spi\0" \ - "uboot_sd=u-boot-p2020.bin\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=2000000\0" \ - "ramdiskfile=rootfs-dev.ext2.img\0" \ - "fdtaddr=c00000\0" \ - "fdtfile=uImage-2.6.32-p2020.dtb\0" \ - "tftppath=p2020\0" - -#define CONFIG_HDBOOT \ - "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "usb start;" \ - "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ - "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $tftppath/$bootfile;" \ - "tftp $fdtaddr $tftppath/$fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $tftppath/$ramdiskfile;" \ - "tftp $loadaddr $tftppath/$bootfile;" \ - "tftp $fdtaddr $tftppath/$fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT - -#endif /* __CONFIG_H */ diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h deleted file mode 100644 index 820b6332a6..0000000000 --- a/include/configs/P2020DS.h +++ /dev/null @@ -1,751 +0,0 @@ -/* - * Copyright 2007-2012 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * p2020ds board configuration file - * - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -#include "../board/freescale/common/ics307_clk.h" - -#ifdef CONFIG_36BIT -#define CONFIG_PHYS_64BIT -#endif - -#ifdef CONFIG_SDCARD -#define CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_EXTRA_ENV_RELOC -#define CONFIG_SYS_TEXT_BASE 0xf8f40000 -#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc -#endif - -#ifdef CONFIG_SPIFLASH -#define CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_EXTRA_ENV_RELOC -#define CONFIG_SYS_TEXT_BASE 0xf8f40000 -#define CONFIG_RESET_VECTOR_ADDRESS 0xf8fffffc -#endif - -/* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ -#define CONFIG_E500 1 /* BOOKE e500 family */ -#define CONFIG_P2020 1 -#define CONFIG_P2020DS 1 -#define CONFIG_MP 1 /* support multiple processors */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xeff40000 -#endif - -#ifndef CONFIG_RESET_VECTOR_ADDRESS -#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc -#endif - -#define CONFIG_SYS_SRIO -#define CONFIG_SRIO1 /* SRIO port 1 */ -#define CONFIG_SRIO2 /* SRIO port 2 */ - -#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */ -#define CONFIG_PCI 1 /* Enable PCI/PCIE */ -#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */ -#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */ -#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */ -#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ -#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ -#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ - -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ -#define CONFIG_E1000 1 /* Defind e1000 pci Ethernet card*/ - -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ -#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() /* ddrclk for MPC85xx */ -#define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 clock chip ref freq */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ - -#define CONFIG_ENABLE_36BIT_PHYS 1 - -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_ADDR_MAP 1 -#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */ -#endif - -#define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 -#define CONFIG_PANIC_HANG /* do not reset board on panic */ - -/* - * Config the L2 Cache - */ -#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_L2_ADDR_PHYS 0xff8f80000ull -#else -#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR -#endif -#define CONFIG_SYS_L2_SIZE (512 << 10) -#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) - -#define CONFIG_SYS_CCSRBAR 0xffe00000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_VERY_BIG_RAM -#ifdef CONFIG_DDR2 -#define CONFIG_SYS_FSL_DDR2 -#else -#define CONFIG_SYS_FSL_DDR3 1 -#endif - -/* ECC will be enabled based on perf_mode environment variable */ -/* #define CONFIG_DDR_ECC */ - -#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_NUM_DDR_CONTROLLERS 1 -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 2 - -/* I2C addresses of SPD EEPROMs */ -#define CONFIG_DDR_SPD -#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD EEPROM located on I2C bus 0 */ -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* These are used when DDR doesn't use SPD. */ -#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1GB */ - -/* Default settings for "stable" mode */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F -#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 -#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 -#define CONFIG_SYS_DDR_TIMING_3 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0 0x00330804 -#define CONFIG_SYS_DDR_TIMING_1 0x6f6b4846 -#define CONFIG_SYS_DDR_TIMING_2 0x0fa890d4 -#define CONFIG_SYS_DDR_MODE_1 0x00421422 -#define CONFIG_SYS_DDR_MODE_2 0x00000000 -#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000 -#define CONFIG_SYS_DDR_INTERVAL 0x61800100 -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_CLK_CTRL 0x02000000 -#define CONFIG_SYS_DDR_TIMING_4 0x00220001 -#define CONFIG_SYS_DDR_TIMING_5 0x03402400 -#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 -#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8655A608 -#define CONFIG_SYS_DDR_CONTROL 0xE7000000 /* Type = DDR3: ECC enabled, No Interleaving */ -#define CONFIG_SYS_DDR_CONTROL2 0x24400011 -#define CONFIG_SYS_DDR_CDR1 0x00040000 -#define CONFIG_SYS_DDR_CDR2 0x00000000 - -#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d -#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 -#define CONFIG_SYS_DDR_SBE 0x00010000 - -/* Settings that differ for "performance" mode */ -#define CONFIG_SYS_DDR_CS0_BNDS_PERF 0x0000007F /* Interleaving Enabled */ -#define CONFIG_SYS_DDR_CS1_BNDS_PERF 0x00000000 /* Interleaving Enabled */ -#define CONFIG_SYS_DDR_CS1_CONFIG_PERF 0x80014202 -#define CONFIG_SYS_DDR_TIMING_1_PERF 0x5d5b4543 -#define CONFIG_SYS_DDR_TIMING_2_PERF 0x0fa890ce -#define CONFIG_SYS_DDR_CONTROL_PERF 0xC7004000 /* Type = DDR3: ECC disabled, cs0-cs1 interleaving */ - -/* - * The following set of values were tested for DDR2 - * with a DDR3 to DDR2 interposer - * -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_TIMING_0 0x00260802 -#define CONFIG_SYS_DDR_TIMING_1 0x3935d322 -#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 -#define CONFIG_SYS_DDR_MODE_1 0x00480432 -#define CONFIG_SYS_DDR_MODE_2 0x00000000 -#define CONFIG_SYS_DDR_INTERVAL 0x06180100 -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 -#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 -#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xC3008000 -#define CONFIG_SYS_DDR_CONTROL2 0x04400010 - * - */ - -/* - * Memory map - * - * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable - * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable - * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable - * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable - * - * Localbus cacheable (TBD) - * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable - * - * Localbus non-cacheable - * 0xe000_0000 0xe80f_ffff Promjet/free 128M non-cacheable - * 0xe800_0000 0xefff_ffff FLASH 128M non-cacheable - * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable - * 0xffdf_0000 0xffdf_7fff PIXIS 32K non-cacheable TLB0 - * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 - * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable - */ - -/* - * Local Bus Definitions - */ -#define CONFIG_SYS_FLASH_BASE 0xe0000000 /* start of FLASH 128M */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull -#else -#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE -#endif - -#define CONFIG_FLASH_BR_PRELIM \ - (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V) -#define CONFIG_FLASH_OR_PRELIM 0xf8000ff7 - -#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) -#define CONFIG_SYS_OR1_PRELIM 0xf8000ff7 - -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} -#define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 - -#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ - -#define CONFIG_HWCONFIG /* enable hwconfig */ -#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */ - -#ifdef CONFIG_FSL_NGPIXIS -#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */ -#ifdef CONFIG_PHYS_64BIT -#define PIXIS_BASE_PHYS 0xfffdf0000ull -#else -#define PIXIS_BASE_PHYS PIXIS_BASE -#endif - -#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V) -#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32KB but only 4k mapped */ - -#define PIXIS_LBMAP_SWITCH 7 -#define PIXIS_LBMAP_MASK 0xf0 -#define PIXIS_LBMAP_SHIFT 4 -#define PIXIS_LBMAP_ALTBANK 0x20 -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR -/* The assembler doesn't like typecast */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ - ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ - CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) -#else -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */ -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 -#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (768 * 1024) -#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ - -#define CONFIG_SYS_NAND_BASE 0xffa00000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull -#else -#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE -#endif -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE,\ - CONFIG_SYS_NAND_BASE + 0x40000, \ - CONFIG_SYS_NAND_BASE + 0x80000,\ - CONFIG_SYS_NAND_BASE + 0xC0000} -#define CONFIG_SYS_MAX_NAND_DEVICE 4 -#define CONFIG_MTD_NAND_VERIFY_WRITE -#define CONFIG_CMD_NAND 1 -#define CONFIG_NAND_FSL_ELBC 1 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) - -/* NAND flash config */ -#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ - | BR_PS_8 /* Port Size = 8bit */ \ - | BR_MS_FCM /* MSEL = FCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_NAND_OR_PRELIM (0xFFFC0000 /* length 256K */ \ - | OR_FCM_PGS /* Large Page*/ \ - | OR_FCM_CSCT \ - | OR_FCM_CST \ - | OR_FCM_CHT \ - | OR_FCM_SCY_1 \ - | OR_FCM_TRLX \ - | OR_FCM_EHTR) - -#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ -#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ -#define CONFIG_SYS_BR2_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */ -#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ - -#define CONFIG_SYS_BR4_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \ - | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ - | BR_PS_8 /* Port Size = 8bit */ \ - | BR_MS_FCM /* MSEL = FCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR4_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ -#define CONFIG_SYS_BR5_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000) \ - | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ - | BR_PS_8 /* Port Size = 8bit */ \ - | BR_MS_FCM /* MSEL = FCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR5_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ - -#define CONFIG_SYS_BR6_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000) \ - | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ - | BR_PS_8 /* Port Size = 8bit */ \ - | BR_MS_FCM /* MSEL = FCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR6_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ - -/* Serial Port - controlled on board with jumper J8 - * open - index 2 - * shorted - index 1 - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Pass open firmware flat tree - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } - -/* - * I2C2 EEPROM - */ -#define CONFIG_ID_EEPROM -#ifdef CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_NXID -#endif -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_BUS_NUM 0 - -/* - * eSPI - Enhanced SPI - */ -#define CONFIG_FSL_ESPI - -#define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_SPANSION - -#define CONFIG_CMD_SF -#define CONFIG_SF_DEFAULT_SPEED 10000000 -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ - -/* controller 3, Slot 1, tgtid 3, Base address b000 */ -#define CONFIG_SYS_PCIE3_NAME "Slot 1" -#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc00000000ull -#else -#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 -#endif -#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 -#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE3_IO_PHYS 0xfffc00000ull -#else -#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 -#endif -#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ - -/* controller 2, direct to uli, tgtid 2, Base address 9000 */ -#define CONFIG_SYS_PCIE2_NAME "ULI" -#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull -#else -#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 -#endif -#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 -#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull -#else -#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 -#endif -#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ - -/* controller 1, Slot 2, tgtid 1, Base address a000 */ -#define CONFIG_SYS_PCIE1_NAME "Slot 2" -#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc40000000ull -#else -#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 -#endif -#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 -#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc20000ull -#else -#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 -#endif -#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ - -#if defined(CONFIG_PCI) - -/*PCIE video card used*/ -#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT - -/* video */ -#undef CONFIG_VIDEO - -#if defined(CONFIG_VIDEO) -#define CONFIG_BIOSEMU -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_ATI_RADEON_FB -#define CONFIG_VIDEO_LOGO -/*#define CONFIG_CONSOLE_CURSOR*/ -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET -#endif - -/* SRIO1 uses the same window as PCIE2 mem window */ -#define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull -#else -#define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 -#endif -#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */ - -/* SRIO2 uses the same window as PCIE1 mem window */ -#define CONFIG_SYS_SRIO2_MEM_VIRT 0xc0000000 -#ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc40000000ull -#else -#define CONFIG_SYS_SRIO2_MEM_PHYS 0xc0000000 -#endif -#define CONFIG_SYS_SRIO2_MEM_SIZE 0x20000000 /* 512M */ - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_DOS_PARTITION -#define CONFIG_SCSI_AHCI - -#ifdef CONFIG_SCSI_AHCI -#define CONFIG_LIBATA -#define CONFIG_SATA_ULI5288 -#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 -#define CONFIG_SYS_SCSI_MAX_LUN 1 -#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) -#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE -#endif /* SCSI */ - -#endif /* CONFIG_PCI */ - - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "eTSEC1" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "eTSEC2" -#define CONFIG_TSEC3 1 -#define CONFIG_TSEC3_NAME "eTSEC3" - -#define CONFIG_FSL_SGMII_RISER 1 -#define SGMII_RISER_PHY_OFFSET 0x1b - -#ifdef CONFIG_FSL_SGMII_RISER -#define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */ -#endif - -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC3_PHY_ADDR 2 - -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) - -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC3_PHYIDX 0 - -#define CONFIG_ETHPRIME "eTSEC1" - -#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#if defined(CONFIG_SDCARD) -#define CONFIG_ENV_IS_IN_MMC -#define CONFIG_FSL_FIXED_MMC_LOCATION -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_SPIFLASH) -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_BUS 0 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_MAX_HZ 10000000 -#define CONFIG_ENV_SPI_MODE 0 -#define CONFIG_ENV_SIZE 0x2000 /* 8KB */ -#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ -#define CONFIG_ENV_SECT_SIZE 0x10000 -#else -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_PING -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_SETEXPR -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#define CONFIG_CMD_NET -#define CONFIG_CMD_SCSI -#define CONFIG_CMD_EXT2 -#endif - -/* - * USB - */ -#define CONFIG_HAS_FSL_DR_USB -#ifdef CONFIG_HAS_FSL_DR_USB -#define CONFIG_USB_EHCI - -#ifdef CONFIG_USB_EHCI -#define CONFIG_CMD_USB -#define CONFIG_USB_STORAGE -#define CONFIG_USB_EHCI_FSL -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET -#endif -#endif - -/* - * SDHC/MMC - */ -#define CONFIG_MMC - -#ifdef CONFIG_MMC -#define CONFIG_FSL_ESDHC -#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR -#define CONFIG_CMD_MMC -#define CONFIG_GENERIC_MMC -#endif - -#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_DOS_PARTITION -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#endif - -#define CONFIG_IPADDR 192.168.1.254 - -#define CONFIG_HOSTNAME unknown -#define CONFIG_ROOTPATH "/opt/nfsroot" -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 1000000 - -#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_EXTRA_ENV_SETTINGS \ -"perf_mode=performance\0" \ - "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1;" \ - "usb1:dr_mode=host,phy_type=ulpi\0" \ -"netdev=eth0\0" \ -"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ -"tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \ -"satabootcmd=setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" \ -"consoledev=ttyS0\0" \ -"ramdiskaddr=2000000\0" \ -"ramdiskfile=p2020ds/ramdisk.uboot\0" \ -"fdtaddr=c00000\0" \ -"othbootargs=cache-sram-size=0x10000\0" \ -"fdtfile=p2020ds/p2020ds.dtb\0" \ -"bdev=sda3\0" \ -"partition=scsi 0:0\0" - -#define CONFIG_HDBOOT \ - "setenv bootargs root=/dev/$bdev rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "ext2load $partition $loadaddr $bootfile;" \ - "ext2load $partition $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT - -#endif /* __CONFIG_H */ diff --git a/include/configs/P3G4.h b/include/configs/P3G4.h deleted file mode 100644 index ac75d3ebfa..0000000000 --- a/include/configs/P3G4.h +++ /dev/null @@ -1,407 +0,0 @@ -/* - * (C) Copyright 2001 - * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#ifndef __ASSEMBLY__ -#include <galileo/core.h> -#endif - -#include "../board/evb64260/local.h" - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_P3G4 1 /* this is a P3G4 board */ -#define CONFIG_SYS_GT_6426x GT_64260 /* with a 64260 system controller */ - -#define CONFIG_SYS_TEXT_BASE 0xfff00000 - -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115200 */ - -#undef CONFIG_ECC /* enable ECC support */ -/* #define CONFIG_EVB64260_750CX 1 */ /* Support the EVB-64260-750CX Board */ - -/* which initialization functions to call for this board */ -#define CONFIG_MISC_INIT_R 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 - -#define CONFIG_SYS_BOARD_NAME "P3G4" - -#undef CONFIG_SYS_HUSH_PARSER - -/* - * The following defines let you select what serial you want to use - * for your console driver. - * - * to use the MPSC, #define CONFIG_MPSC. If you have wired up another - * mpsc channel, change CONFIG_MPSC_PORT to the desired value. - */ -#define CONFIG_MPSC -#define CONFIG_MPSC_PORT 0 - - -/* define this if you want to enable GT MAC filtering */ -#define CONFIG_GT_USE_MAC_HASH_TABLE - -#undef CONFIG_ETHER_PORT_MII /* use RMII */ - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=p3g4\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_74xx\0" \ - "bootfile=/tftpboot/p3g4/uImage\0" \ - "kernel_addr=ff000000\0" \ - "ramdisk_addr=ff010000\0" \ - "load=tftp 100000 /tftpboot/p3g4/u-boot.bin\0" \ - "update=protect off fff00000 fff3ffff;era fff00000 fff3ffff;" \ - "cp.b 100000 fff00000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#undef CONFIG_ALTIVEC /* undef to disable */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PCI -#define CONFIG_CMD_ELF -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_UNIVERSE -#define CONFIG_CMD_BSP - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00300000 /* default load address */ -#define CONFIG_SYS_BUS_CLK 133000000 /* 133 MHz */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_RAM_LOCK - - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xff000000 -#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ - -/* areas to map different things with the GT in physical space */ -#define CONFIG_SYS_DRAM_BANKS 1 -#define CONFIG_SYS_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */ - -/* What to put in the bats. */ -#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000 - -/* Peripheral Device section */ -#define CONFIG_SYS_GT_REGS 0xf8000000 -#define CONFIG_SYS_DEV_BASE 0xff000000 - -#define CONFIG_SYS_DEV0_SPACE CONFIG_SYS_DEV_BASE -#define CONFIG_SYS_DEV1_SPACE (CONFIG_SYS_DEV0_SPACE + CONFIG_SYS_DEV0_SIZE) -#define CONFIG_SYS_DEV2_SPACE (CONFIG_SYS_DEV1_SPACE + CONFIG_SYS_DEV1_SIZE) -#define CONFIG_SYS_DEV3_SPACE (CONFIG_SYS_DEV2_SPACE + CONFIG_SYS_DEV2_SIZE) - -#define CONFIG_SYS_DEV0_SIZE _8M /* Flash bank */ -#define CONFIG_SYS_DEV1_SIZE 0 /* unused */ -#define CONFIG_SYS_DEV2_SIZE 0 /* unused */ -#define CONFIG_SYS_DEV3_SIZE 0 /* unused */ - -#define CONFIG_SYS_16BIT_BOOT_PAR 0xc01b5e7c -#define CONFIG_SYS_DEV0_PAR CONFIG_SYS_16BIT_BOOT_PAR - -#if 0 /* Wrong?? NTL */ -#define CONFIG_SYS_MPP_CONTROL_0 0x53541717 /* InitAct EOT[4] DBurst TCEn[1] */ - /* DMAAck[1:0] GNT0[1:0] */ -#else -#define CONFIG_SYS_MPP_CONTROL_0 0x53547777 /* InitAct EOT[4] DBurst TCEn[1] */ - /* REQ0[1:0] GNT0[1:0] */ -#endif -#define CONFIG_SYS_MPP_CONTROL_1 0x44009911 /* TCEn[4] TCTcnt[4] GPP[13:12] */ - /* DMAReq[4] DMAAck[4] WDNMI WDE */ -#if 0 /* Wrong?? NTL */ -#define CONFIG_SYS_MPP_CONTROL_2 0x40091818 /* TCTcnt[0] GPP[22:21] BClkIn */ - /* DMAAck[1:0] GNT1[1:0] */ -#else -#define CONFIG_SYS_MPP_CONTROL_2 0x40098888 /* TCTcnt[0] */ - /* GPP[22] (RS232IntB or PCI1Int) */ - /* GPP[21] (RS323IntA) */ - /* BClkIn */ - /* REQ1[1:0] GNT1[1:0] */ -#endif - -#if 0 /* Wrong?? NTL */ -# define CONFIG_SYS_MPP_CONTROL_3 0x00090066 /* GPP[31:29] BClkOut0 */ - /* GPP[27:26] Int[1:0] */ -#else -# define CONFIG_SYS_MPP_CONTROL_3 0x22090066 /* MREQ MGNT */ - /* GPP[29] (PCI1Int) */ - /* BClkOut0 */ - /* GPP[27] (PCI0Int) */ - /* GPP[26] (RtcInt or PCI1Int) */ - /* CPUInt[25:24] */ -#endif - -#define CONFIG_SYS_SERIAL_PORT_MUX 0x00001102 /* 11=MPSC1/MPSC0 02=ETH 0 and 2 RMII */ - -#if 0 /* Wrong?? - NTL */ -# define CONFIG_SYS_GPP_LEVEL_CONTROL 0x000002c6 -#else -# define CONFIG_SYS_GPP_LEVEL_CONTROL 0x2c600000 /* 0010 1100 0110 0000 */ - /* gpp[29] */ - /* gpp[27:26] */ - /* gpp[22:21] */ - -# define CONFIG_SYS_SDRAM_CONFIG 0xd8e18200 /* 0x448 */ - /* idmas use buffer 1,1 - comm use buffer 0 - pci use buffer 1,1 - cpu use buffer 0 - normal load (see also ifdef HVL) - standard SDRAM (see also ifdef REG) - non staggered refresh */ - /* 31:26 25 23 20 19 18 16 */ - /* 110110 00 111 0 0 00 1 */ - /* refresh_count=0x200 - phisical interleaving disable - virtual interleaving enable */ - /* 15 14 13:0 */ - /* 1 0 0x200 */ -#endif - -#if 0 -#define CONFIG_SYS_DUART_IO CONFIG_SYS_DEV2_SPACE -#define CONFIG_SYS_DUART_CHAN 1 /* channel to use for console */ -#endif -#undef CONFIG_SYS_INIT_CHAN1 -#undef CONFIG_SYS_INIT_CHAN2 -#if 0 -#define SRAM_BASE CONFIG_SYS_DEV0_SPACE -#define SRAM_SIZE 0x00100000 /* 1 MB of sram */ -#endif - - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ - -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -/* PCI MEMORY MAP section */ -#define CONFIG_SYS_PCI0_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI0_MEM_SIZE _128M -#define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE) - -#define CONFIG_SYS_PCI1_MEM_BASE 0x88000000 -#define CONFIG_SYS_PCI1_MEM_SIZE _128M -#define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE) - -/* PCI I/O MAP section */ -#define CONFIG_SYS_PCI0_IO_BASE 0xfa000000 -#define CONFIG_SYS_PCI0_IO_SIZE _16M -#define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE) -#define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000 - -#define CONFIG_SYS_PCI1_IO_BASE 0xfb000000 -#define CONFIG_SYS_PCI1_IO_SIZE _16M -#define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE) -#define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000 - -/*---------------------------------------------------------------------- - * Initial BAT mappings - */ - -/* NOTES: - * 1) GUARDED and WRITE_THRU not allowed in IBATS - * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT - */ - -/* SDRAM */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* init ram */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* PCI0, PCI1 in one BAT */ -#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS -#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -/* GT regs, bootrom, all the devices, PCI I/O */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M) -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* I2C speed and slave address (for compatability) defaults */ -#define CONFIG_SYS_I2C_SPEED 400000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* I2C addresses for the two DIMM SPD chips */ -#ifndef CONFIG_EVB64260_750CX -#define DIMM0_I2C_ADDR 0x56 -#define DIMM1_I2C_ADDR 0x54 -#else /* CONFIG_EVB64260_750CX - only has 1 DIMM */ -#define DIMM0_I2C_ADDR 0x54 -#define DIMM1_I2C_ADDR 0x54 -#endif - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ - -#define CONFIG_SYS_EXTRA_FLASH_DEVICE BOOT_DEVICE -#define CONFIG_SYS_EXTRA_FLASH_WIDTH 2 /* 16 bit */ -#define CONFIG_SYS_BOOT_FLASH_WIDTH 2 /* 16 bit */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_CFI 1 - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR 0xFFFE0000 - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * L2CR setup -- make sure this is right for your board! - * look in include/74xx_7xx.h for the defines used here - */ - -#define CONFIG_SYS_L2 - -#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ - L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) - -#define L2_ENABLE (L2_INIT | L2CR_L2E) - -#define CONFIG_SYS_BOARD_ASM_INIT 1 - - -#endif /* __CONFIG_H */ diff --git a/include/configs/PM520.h b/include/configs/PM520.h deleted file mode 100644 index de46216422..0000000000 --- a/include/configs/PM520.h +++ /dev/null @@ -1,342 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 -#define CONFIG_PM520 1 /* PM520 board */ - -#define CONFIG_SYS_TEXT_BASE 0xfff00000 - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ - -#define CONFIG_MISC_INIT_R - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 9600 /* ... at 9600 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_MII 1 -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#undef CONFIG_NS8382X - - -/* Partitions */ -#define CONFIG_DOS_PARTITION - -/* USB */ -#if 1 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_USB - -#define CONFIG_CMD_PCI - - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=pm520\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk30/ppc_82xx\0" \ - "bootfile=/tftpboot/PM520/uImage\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 - -/* - * RTC configuration - */ -#define CONFIG_RTC_PCF8563 -#define CONFIG_SYS_I2C_RTC_ADDR 0x51 - -#define CONFIG_SYS_DOC_BASE 0xE0000000 -#define CONFIG_SYS_DOC_SIZE 0x00100000 - -#if defined(CONFIG_BOOT_ROM) -/* - * Flash configuration (8,16 or 32 MB) - * TEXT base always at 0xFFF00000 - * ENV_ADDR always at 0xFFF40000 - * FLASH_BASE at 0xFA000000 for 64 MB - * 0xFC000000 for 32 MB - * 0xFD000000 for 16 MB - * 0xFD800000 for 8 MB - */ -#define CONFIG_SYS_FLASH_BASE 0xFA000000 -#define CONFIG_SYS_FLASH_SIZE 0x04000000 -#define CONFIG_SYS_BOOTROM_BASE 0xFFF00000 -#define CONFIG_SYS_BOOTROM_SIZE 0x00080000 -#define CONFIG_ENV_ADDR (0xFDF00000 + 0x40000) -#else -/* - * Flash configuration (8,16 or 32 MB) - * TEXT base always at 0xFFF00000 - * ENV_ADDR always at 0xFFF40000 - * FLASH_BASE at 0xFC000000 for 64 MB - * 0xFE000000 for 32 MB - * 0xFF000000 for 16 MB - * 0xFF800000 for 8 MB - */ -#define CONFIG_SYS_FLASH_BASE 0xFC000000 -#define CONFIG_SYS_FLASH_SIZE 0x04000000 -#define CONFIG_ENV_ADDR (0xFFF00000 + 0x40000) -#endif -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ - -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ -#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ -#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ -#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ - -#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ - -#undef CONFIG_FLASH_16BIT /* Flash is 32-bit */ - - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x40000 -#define CONFIG_ENV_OVERWRITE 1 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xf0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#if defined(CONFIG_BOOT_ROM) -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_BOOTROM_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_BOOTROM_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047800 -#define CONFIG_SYS_CS0_START CONFIG_SYS_BOOTROM_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_BOOTROM_SIZE -#define CONFIG_SYS_CS1_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_CS1_CFG 0x0004FF00 -#else -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0004FF00 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_CS1_START CONFIG_SYS_DOC_BASE -#define CONFIG_SYS_CS1_SIZE CONFIG_SYS_DOC_SIZE -#define CONFIG_SYS_CS1_CFG 0x00047800 -#endif - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00005000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#undef CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/PPChameleonEVB.h b/include/configs/PPChameleonEVB.h deleted file mode 100644 index e277d0d933..0000000000 --- a/include/configs/PPChameleonEVB.h +++ /dev/null @@ -1,777 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, <wd@denx.de> - * - * (C) Copyright 2003 - * DAVE Srl - * - * http://www.dave-tech.it - * http://www.wawnet.biz - * mailto:info@wawnet.biz - * - * Credits: Stefan Roese, Wolfgang Denk - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PPCHAMELEON_MODULE_BA 0 /* Basic Model */ -#define CONFIG_PPCHAMELEON_MODULE_ME 1 /* Medium Model */ -#define CONFIG_PPCHAMELEON_MODULE_HI 2 /* High-End Model */ -#ifndef CONFIG_PPCHAMELEON_MODULE_MODEL -#define CONFIG_PPCHAMELEON_MODULE_MODEL CONFIG_PPCHAMELEON_MODULE_BA -#endif - - -/* Only one of the following two symbols must be defined (default is 25 MHz) - * CONFIG_PPCHAMELEON_CLK_25 - * CONFIG_PPCHAMELEON_CLK_33 - */ -#if (!defined(CONFIG_PPCHAMELEON_CLK_25) && !defined(CONFIG_PPCHAMELEON_CLK_33)) -#define CONFIG_PPCHAMELEON_CLK_25 -#endif - -#if (defined(CONFIG_PPCHAMELEON_CLK_25) && defined(CONFIG_PPCHAMELEON_CLK_33)) -#error "* Two external frequencies (SysClk) are defined! *" -#endif - -#undef CONFIG_PPCHAMELEON_SMI712 - -/* - * Debug stuff - */ -#undef __DEBUG_START_FROM_SRAM__ -#define __DISABLE_MACHINE_EXCEPTION__ - -#ifdef __DEBUG_START_FROM_SRAM__ -#define CONFIG_SYS_DUMMY_FLASH_SIZE 1024*1024*4 -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405EP 1 /* This is a PPC405 CPU */ -#define CONFIG_PPCHAMELEONEVB 1 /* ...on a PPChameleonEVB board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFFB0000 /* Reserve 320 kB for Monitor */ -#define CONFIG_SYS_LDSCRIPT "board/dave/PPChameleonEVB/u-boot.lds" - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -# define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) -# define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#else -# error "* External frequency (SysClk) not defined! *" -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#undef CONFIG_BOOTARGS - -/* Ethernet stuff */ -#define CONFIG_ENV_OVERWRITE /* Let the user to change the Ethernet MAC addresses */ -#define CONFIG_ETHADDR 00:50:c2:1e:af:fe -#define CONFIG_HAS_ETH1 -#define CONFIG_ETH1ADDR 00:50:c2:1e:af:fd - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#undef CONFIG_EXT_PHY - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#ifndef CONFIG_EXT_PHY -#define CONFIG_PHY_ADDR 1 /* EMAC0 PHY address */ -#define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ -#else -#define CONFIG_PHY_ADDR 2 /* PHY address */ -#endif -#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NAND -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SNTP - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#define CONFIG_RTC_M41T11 1 /* uses a M41T00 RTC */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 -#define CONFIG_SYS_M41T11_BASE_YEAR 1900 - -/* - * SDRAM configuration (please see cpu/ppc/sdram.[ch]) - */ -#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ - -/* SDRAM timings used in datasheet */ -#define CONFIG_SYS_SDRAM_CL 2 -#define CONFIG_SYS_SDRAM_tRP 20 -#define CONFIG_SYS_SDRAM_tRC 65 -#define CONFIG_SYS_SDRAM_tRCD 20 -#undef CONFIG_SYS_SDRAM_tRFC - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ -#define CONFIG_SYS_BASE_BAUD 691200 - -/* The following table includes the supported baudrates */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ - 57600, 115200, 230400, 460800, 921600 } - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ - -/*----------------------------------------------------------------------- - * NAND-FLASH stuff - *----------------------------------------------------------------------- - */ - -/* - * nand device 1 on dave (PPChameleonEVB) needs more time, - * so we just introduce additional wait in nand_wait(), - * effectively for both devices. - */ -#define PPCHAMELON_NAND_TIMER_HACK - -#define CONFIG_SYS_NAND0_BASE 0xFF400000 -#define CONFIG_SYS_NAND1_BASE 0xFF000000 -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND0_BASE, CONFIG_SYS_NAND1_BASE } -#define NAND_BIG_DELAY_US 25 -#define CONFIG_SYS_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ - -#define CONFIG_SYS_NAND0_CE (0x80000000 >> 1) /* our CE is GPIO1 */ -#define CONFIG_SYS_NAND0_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */ -#define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */ -#define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */ - -#define CONFIG_SYS_NAND1_CE (0x80000000 >> 14) /* our CE is GPIO14 */ -#define CONFIG_SYS_NAND1_RDY (0x80000000 >> 31) /* our RDY is GPIO31 */ -#define CONFIG_SYS_NAND1_CLE (0x80000000 >> 15) /* our CLE is GPIO15 */ -#define CONFIG_SYS_NAND1_ALE (0x80000000 >> 16) /* our ALE is GPIO16 */ - -#define MACRO_NAND_DISABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_ENABLE_CE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETALE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_ALE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_ALE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_CLRCLE(nandptr) do \ -{ \ - switch((unsigned long)nandptr) \ - { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -#define MACRO_NAND_CTL_SETCLE(nandptr) do { \ - switch((unsigned long)nandptr) { \ - case CONFIG_SYS_NAND0_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND0_CLE); \ - break; \ - case CONFIG_SYS_NAND1_BASE: \ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_NAND1_CLE); \ - break; \ - } \ -} while(0) - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#undef CONFIG_PCI_PNP /* do pci plug-and-play */ - /* resource configuration */ - -#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: --- */ -#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/ - -#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CONFIG_SYS_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */ -#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ -#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -/* Reserve 256 kB for Monitor */ -/* -#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) -*/ - -/* Reserve 320 kB for Monitor */ -#define CONFIG_SYS_FLASH_BASE 0xFFFB0000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MONITOR_LEN (320 * 1024) - -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ -/* - * The following defines are added for buggy IOP480 byte interface. - * All other boards should use the standard values (CPCI405 etc.) - */ -#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ -#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ -#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/*----------------------------------------------------------------------- - * Environment Variable setup - */ -#ifdef ENVIRONMENT_IN_EEPROM - -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x100 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x700 /* 2048-256 bytes may be used for env vars (total size of a CAT24WC16 is 2048 bytes)*/ - -#else /* DEFAULT: environment in flash, using redundand flash sectors */ - -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_ADDR 0xFFFF8000 /* environment starts at the first small sector */ -#define CONFIG_ENV_SECT_SIZE 0x2000 /* 8196 bytes may be used for env vars*/ -#define CONFIG_ENV_ADDR_REDUND 0xFFFFA000 -#define CONFIG_ENV_SIZE_REDUND 0x2000 - -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -#endif /* ENVIRONMENT_IN_EEPROM */ - - -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xF0000500 /* NVRAM base address */ -#define CONFIG_SYS_NVRAM_SIZE 242 /* NVRAM size */ - -/*----------------------------------------------------------------------- - * I2C EEPROM (CAT24WC16) for environment - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -/*#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07*/ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ - /* 16 byte page write mode using*/ - /* last 4 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */ - -/*----------------------------------------------------------------------- - * External Bus Controller (EBC) Setup - */ - -/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB0AP 0x92015480 -#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ - -/* Memory Bank 1 (External SRAM) initialization */ -/* Since this must replace NOR Flash, we use the same settings for CS0 */ -#define CONFIG_SYS_EBC_PB1AP 0x92015480 -#define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 2 (Flash Bank 1, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB2AP 0x92015480 -#define CONFIG_SYS_EBC_PB2CR 0xFF458000 /* BAS=0xFF4,BS=4MB,BU=R/W,BW=8bit */ - -/* Memory Bank 3 (Flash Bank 2, NAND-FLASH) initialization */ -#define CONFIG_SYS_EBC_PB3AP 0x92015480 -#define CONFIG_SYS_EBC_PB3CR 0xFF058000 /* BAS=0xFF0,BS=4MB,BU=R/W,BW=8bit */ - -#ifdef CONFIG_PPCHAMELEON_SMI712 -/* - * Video console (graphic: SMI LynxEM) - */ -#define CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_SMI_LYNXEM -#define CONFIG_VIDEO_LOGO -/*#define CONFIG_VIDEO_BMP_LOGO*/ -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VGA_AS_SINGLE_DEVICE -/* This is the base address (on 405EP-side) used to generate I/O accesses on PCI bus */ -#define CONFIG_SYS_ISA_IO 0xE8000000 -/* see also drivers/video/videomodes.c */ -#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x303 -#endif - -/*----------------------------------------------------------------------- - * FPGA stuff - */ -/* FPGA internal regs */ -#define CONFIG_SYS_FPGA_MODE 0x00 -#define CONFIG_SYS_FPGA_STATUS 0x02 -#define CONFIG_SYS_FPGA_TS 0x04 -#define CONFIG_SYS_FPGA_TS_LOW 0x06 -#define CONFIG_SYS_FPGA_TS_CAP0 0x10 -#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 -#define CONFIG_SYS_FPGA_TS_CAP1 0x14 -#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 -#define CONFIG_SYS_FPGA_TS_CAP2 0x18 -#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a -#define CONFIG_SYS_FPGA_TS_CAP3 0x1c -#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e - -/* FPGA Mode Reg */ -#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100 -#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000 -#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000 - -/* FPGA Status Reg */ -#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 -#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 -#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 -#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 -#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000 - -#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/ - -/* FPGA program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ -#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */ -#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in data cache) - */ -/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 - -/* On Chip Memory location */ -#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Definitions for GPIO setup (PPC405EP specific) - * - * GPIO0[0] - External Bus Controller BLAST output - * GPIO0[1-9] - Instruction trace outputs -> GPIO - * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs - * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO - * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs - * GPIO0[24-27] - UART0 control signal inputs/outputs - * GPIO0[28-29] - UART1 data signal input/output - * GPIO0[30] - EMAC0 input - * GPIO0[31] - EMAC1 reject packet as output - */ -#define CONFIG_SYS_GPIO0_OSRL 0x40000550 -#define CONFIG_SYS_GPIO0_OSRH 0x00000110 -#define CONFIG_SYS_GPIO0_ISR1L 0x00000000 -/*#define CONFIG_SYS_GPIO0_ISR1H 0x15555445*/ -#define CONFIG_SYS_GPIO0_ISR1H 0x15555444 -#define CONFIG_SYS_GPIO0_TSRL 0x00000000 -#define CONFIG_SYS_GPIO0_TSRH 0x00000000 -#define CONFIG_SYS_GPIO0_TCR 0xF7FF8014 - -#define CONFIG_NO_SERIAL_EEPROM - -/*--------------------------------------------------------------------*/ - -#ifdef CONFIG_NO_SERIAL_EEPROM - -/* -!----------------------------------------------------------------------- -! Defines for entry options. -! Note: Because the 405EP SDRAM controller does not support ECC, ECC DIMMs that -! are plugged in the board will be utilized as non-ECC DIMMs. -!----------------------------------------------------------------------- -*/ -#undef AUTO_MEMORY_CONFIG -#define DIMM_READ_ADDR 0xAB -#define DIMM_WRITE_ADDR 0xAA - -/* Defines for CPC0_PLLMR1 Register fields */ -#define PLL_ACTIVE 0x80000000 -#define CPC0_PLLMR1_SSCS 0x80000000 -#define PLL_RESET 0x40000000 -#define CPC0_PLLMR1_PLLR 0x40000000 - /* Feedback multiplier */ -#define PLL_FBKDIV 0x00F00000 -#define CPC0_PLLMR1_FBDV 0x00F00000 -#define PLL_FBKDIV_16 0x00000000 -#define PLL_FBKDIV_1 0x00100000 -#define PLL_FBKDIV_2 0x00200000 -#define PLL_FBKDIV_3 0x00300000 -#define PLL_FBKDIV_4 0x00400000 -#define PLL_FBKDIV_5 0x00500000 -#define PLL_FBKDIV_6 0x00600000 -#define PLL_FBKDIV_7 0x00700000 -#define PLL_FBKDIV_8 0x00800000 -#define PLL_FBKDIV_9 0x00900000 -#define PLL_FBKDIV_10 0x00A00000 -#define PLL_FBKDIV_11 0x00B00000 -#define PLL_FBKDIV_12 0x00C00000 -#define PLL_FBKDIV_13 0x00D00000 -#define PLL_FBKDIV_14 0x00E00000 -#define PLL_FBKDIV_15 0x00F00000 - /* Forward A divisor */ -#define PLL_FWDDIVA 0x00070000 -#define CPC0_PLLMR1_FWDVA 0x00070000 -#define PLL_FWDDIVA_8 0x00000000 -#define PLL_FWDDIVA_7 0x00010000 -#define PLL_FWDDIVA_6 0x00020000 -#define PLL_FWDDIVA_5 0x00030000 -#define PLL_FWDDIVA_4 0x00040000 -#define PLL_FWDDIVA_3 0x00050000 -#define PLL_FWDDIVA_2 0x00060000 -#define PLL_FWDDIVA_1 0x00070000 - /* Forward B divisor */ -#define PLL_FWDDIVB 0x00007000 -#define CPC0_PLLMR1_FWDVB 0x00007000 -#define PLL_FWDDIVB_8 0x00000000 -#define PLL_FWDDIVB_7 0x00001000 -#define PLL_FWDDIVB_6 0x00002000 -#define PLL_FWDDIVB_5 0x00003000 -#define PLL_FWDDIVB_4 0x00004000 -#define PLL_FWDDIVB_3 0x00005000 -#define PLL_FWDDIVB_2 0x00006000 -#define PLL_FWDDIVB_1 0x00007000 - /* PLL tune bits */ -#define PLL_TUNE_MASK 0x000003FF -#define PLL_TUNE_2_M_3 0x00000133 /* 2 <= M <= 3 */ -#define PLL_TUNE_4_M_6 0x00000134 /* 3 < M <= 6 */ -#define PLL_TUNE_7_M_10 0x00000138 /* 6 < M <= 10 */ -#define PLL_TUNE_11_M_14 0x0000013C /* 10 < M <= 14 */ -#define PLL_TUNE_15_M_40 0x0000023E /* 14 < M <= 40 */ -#define PLL_TUNE_VCO_LOW 0x00000000 /* 500MHz <= VCO <= 800MHz */ -#define PLL_TUNE_VCO_HI 0x00000080 /* 800MHz < VCO <= 1000MHz */ - -/* Defines for CPC0_PLLMR0 Register fields */ - /* CPU divisor */ -#define PLL_CPUDIV 0x00300000 -#define CPC0_PLLMR0_CCDV 0x00300000 -#define PLL_CPUDIV_1 0x00000000 -#define PLL_CPUDIV_2 0x00100000 -#define PLL_CPUDIV_3 0x00200000 -#define PLL_CPUDIV_4 0x00300000 - /* PLB divisor */ -#define PLL_PLBDIV 0x00030000 -#define CPC0_PLLMR0_CBDV 0x00030000 -#define PLL_PLBDIV_1 0x00000000 -#define PLL_PLBDIV_2 0x00010000 -#define PLL_PLBDIV_3 0x00020000 -#define PLL_PLBDIV_4 0x00030000 - /* OPB divisor */ -#define PLL_OPBDIV 0x00003000 -#define CPC0_PLLMR0_OPDV 0x00003000 -#define PLL_OPBDIV_1 0x00000000 -#define PLL_OPBDIV_2 0x00001000 -#define PLL_OPBDIV_3 0x00002000 -#define PLL_OPBDIV_4 0x00003000 - /* EBC divisor */ -#define PLL_EXTBUSDIV 0x00000300 -#define CPC0_PLLMR0_EPDV 0x00000300 -#define PLL_EXTBUSDIV_2 0x00000000 -#define PLL_EXTBUSDIV_3 0x00000100 -#define PLL_EXTBUSDIV_4 0x00000200 -#define PLL_EXTBUSDIV_5 0x00000300 - /* MAL divisor */ -#define PLL_MALDIV 0x00000030 -#define CPC0_PLLMR0_MPDV 0x00000030 -#define PLL_MALDIV_1 0x00000000 -#define PLL_MALDIV_2 0x00000010 -#define PLL_MALDIV_3 0x00000020 -#define PLL_MALDIV_4 0x00000030 - /* PCI divisor */ -#define PLL_PCIDIV 0x00000003 -#define CPC0_PLLMR0_PPFD 0x00000003 -#define PLL_PCIDIV_1 0x00000000 -#define PLL_PCIDIV_2 0x00000001 -#define PLL_PCIDIV_3 0x00000002 -#define PLL_PCIDIV_4 0x00000003 - -#ifdef CONFIG_PPCHAMELEON_CLK_25 -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 25.0 MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#elif (defined (CONFIG_PPCHAMELEON_CLK_33)) - -/* CPU - PLB/SDRAM - EBC - OPB - PCI (assuming a 33.3MHz input clock to the 405EP) */ -#define PPCHAMELEON_PLLMR0_133_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_1 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_133_133_33_66_33 (PLL_FBKDIV_4 | \ - PLL_FWDDIVA_6 | PLL_FWDDIVB_6 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_200_100_50_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_200_100_50_33 (PLL_FBKDIV_6 | \ - PLL_FWDDIVA_4 | PLL_FWDDIVB_4 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_266_133_33_66_33 (PLL_CPUDIV_1 | PLL_PLBDIV_2 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_4 | \ - PLL_MALDIV_1 | PLL_PCIDIV_4) -#define PPCHAMELEON_PLLMR1_266_133_33_66_33 (PLL_FBKDIV_8 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_LOW) - -#define PPCHAMELEON_PLLMR0_333_111_37_55_55 (PLL_CPUDIV_1 | PLL_PLBDIV_3 | \ - PLL_OPBDIV_2 | PLL_EXTBUSDIV_3 | \ - PLL_MALDIV_1 | PLL_PCIDIV_2) -#define PPCHAMELEON_PLLMR1_333_111_37_55_55 (PLL_FBKDIV_10 | \ - PLL_FWDDIVA_3 | PLL_FWDDIVB_3 | \ - PLL_TUNE_15_M_40 | PLL_TUNE_VCO_HI) - -#else -#error "* External frequency (SysClk) not defined! *" -#endif - -#if (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_HI) -/* Model HI */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_333_111_37_55_55 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_333_111_37_55_55 -#define CONFIG_SYS_OPB_FREQ 55555555 -/* Model ME */ -#elif (CONFIG_PPCHAMELEON_MODULE_MODEL == CONFIG_PPCHAMELEON_MODULE_ME) -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_266_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_266_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#else -/* Model BA (default) */ -#define PLLMR0_DEFAULT PPCHAMELEON_PLLMR0_133_133_33_66_33 -#define PLLMR1_DEFAULT PPCHAMELEON_PLLMR1_133_133_33_66_33 -#define CONFIG_SYS_OPB_FREQ 66666666 -#endif - -#endif /* CONFIG_NO_SERIAL_EEPROM */ - -#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */ -#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */ - -/* - * JFFS2 partitions - */ - -/* No command line, one static partition */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nand0" -#define CONFIG_JFFS2_PART_SIZE 0x00400000 -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=PPChameleon-0,nand0=ppchameleonevb-nand" -*/ - -/* 256 kB U-boot image */ -/* -#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \ - "1792k(user),256k(u-boot);" \ - "ppchameleonevb-nand:-(nand)" -*/ - -/* 320 kB U-boot image */ -/* -#define MTDPARTS_DEFAULT "mtdparts=PPChameleon-0:1m(kernel1),1m(kernel2)," \ - "1728k(user),320k(u-boot);" \ - "ppchameleonevb-nand:-(nand)" -*/ - -#endif /* __CONFIG_H */ diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h index c2bdbb99ed..3f02cede32 100644 --- a/include/configs/T102xQDS.h +++ b/include/configs/T102xQDS.h @@ -35,7 +35,10 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_DEEP_SLEEP +#if defined(CONFIG_DEEP_SLEEP) #define CONFIG_SILENT_CONSOLE +#define CONFIG_BOARD_EARLY_INIT_F +#endif #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h index 82b669ba6e..bd40d6ac93 100644 --- a/include/configs/T102xRDB.h +++ b/include/configs/T102xRDB.h @@ -36,7 +36,10 @@ /* support deep sleep */ #define CONFIG_DEEP_SLEEP +#if defined(CONFIG_DEEP_SLEEP) #define CONFIG_SILENT_CONSOLE +#define CONFIG_BOARD_EARLY_INIT_F +#endif #ifdef CONFIG_RAMBOOT_PBL #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg @@ -51,7 +54,7 @@ #define CONFIG_SPL_I2C_SUPPORT #define CONFIG_SPL_DRIVERS_MISC_SUPPORT #define CONFIG_FSL_LAW /* Use common FSL init code */ -#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SYS_TEXT_BASE 0x30001000 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 #define CONFIG_SPL_PAD_TO 0x40000 #define CONFIG_SPL_MAX_SIZE 0x28000 @@ -67,21 +70,21 @@ #ifdef CONFIG_NAND #define CONFIG_SPL_NAND_SUPPORT #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 -#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_DST 0x30000000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x30000000 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" #define CONFIG_SPL_NAND_BOOT #endif #ifdef CONFIG_SPIFLASH -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC +#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC #define CONFIG_SPL_SPI_SUPPORT #define CONFIG_SPL_SPI_FLASH_SUPPORT #define CONFIG_SPL_SPI_FLASH_MINIMAL #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) -#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x30000000) +#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x30000000) #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" #ifndef CONFIG_SPL_BUILD @@ -91,12 +94,12 @@ #endif #ifdef CONFIG_SDCARD -#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC +#define CONFIG_RESET_VECTOR_ADDRESS 0x30000FFC #define CONFIG_SPL_MMC_SUPPORT #define CONFIG_SPL_MMC_MINIMAL #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) -#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) -#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) +#define CONFIG_SYS_MMC_U_BOOT_DST (0x30000000) +#define CONFIG_SYS_MMC_U_BOOT_START (0x30000000) #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds" #ifndef CONFIG_SPL_BUILD @@ -759,8 +762,10 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_FMAN_ENET #define CONFIG_PHYLIB_10G #define CONFIG_PHY_REALTEK +#define CONFIG_PHY_AQUANTIA #define RGMII_PHY1_ADDR 0x2 #define RGMII_PHY2_ADDR 0x6 +#define SGMII_PHY1_ADDR 0x2 #define FM1_10GEC1_PHY_ADDR 0x1 #endif diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h index b70bdfe5e7..92f5f56718 100644 --- a/include/configs/T1040QDS.h +++ b/include/configs/T1040QDS.h @@ -47,7 +47,10 @@ /* support deep sleep */ #define CONFIG_DEEP_SLEEP +#if defined(CONFIG_DEEP_SLEEP) #define CONFIG_SILENT_CONSOLE +#define CONFIG_BOARD_EARLY_INIT_F +#endif #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0xeff40000 @@ -689,6 +692,12 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ #endif +/* Enable VSC9953 L2 Switch driver */ +#define CONFIG_VSC9953 +#define CONFIG_VSC9953_CMD +#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x14 +#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x18 + /* * Dynamic MTD Partition support with mtdparts */ diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h index 57cdf7213c..d47f1be685 100644 --- a/include/configs/T104xRDB.h +++ b/include/configs/T104xRDB.h @@ -726,6 +726,14 @@ #define CONFIG_SYS_RGMII1_PHY_ADDR 0x01 #define CONFIG_SYS_RGMII2_PHY_ADDR 0x02 +/* Enable VSC9953 L2 Switch driver on T1040 SoC */ +#ifdef CONFIG_T1040RDB +#define CONFIG_VSC9953 +#define CONFIG_VSC9953_CMD +#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x04 +#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x08 +#endif + #define CONFIG_MII /* MII PHY management */ #define CONFIG_ETHPRIME "FM1@DTSEC4" #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h deleted file mode 100644 index a58eecab84..0000000000 --- a/include/configs/Total5200.h +++ /dev/null @@ -1,386 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004 - * Mark Jonas, Freescale Semiconductor, mark.jonas@freescale.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Check valid setting of revision define. - * Total5100 and Total5200 Rev.1 are identical except for the processor. - */ -#if (CONFIG_TOTAL5200_REV!=1 && CONFIG_TOTAL5200_REV!=2) -#error CONFIG_TOTAL5200_REV must be 1 or 2 -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_TOTAL5200 1 /* ... on Total5200 board */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFFF00000 boot high (standard configuration) - * 0xFE000000 boot low - * 0x00100000 boot from RAM (for testing only) - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Video console - */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_SED13806 -#define CONFIG_VIDEO_SED13806_16BPP - -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -/* #define CONFIG_VIDEO_BMP_LOGO */ -#define CONFIG_CONSOLE_EXTRA_INFO -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_SPLASH_SCREEN - - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_MII 1 -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* USB */ -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI - -#define CONFIG_CMD_BMP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_PING -#define CONFIG_CMD_USB - - -#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */ -# define CONFIG_SYS_LOWBOOT 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT \ - "setenv stdout serial;setenv stderr serial;" \ - "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "flash_nfs=run nfsargs addip;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "bootfile=/tftpboot/MPC5200/uImage\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#if CONFIG_TOTAL5200_REV==2 -# define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max num of flash banks */ -# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS5_START, CONFIG_SYS_CS4_START, CONFIG_SYS_BOOTCS_START } -#else -# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } -#endif -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ - -#if CONFIG_TOTAL5200_REV==1 -# define CONFIG_SYS_FLASH_BASE 0xFE000000 -# define CONFIG_SYS_FLASH_SIZE 0x02000000 -#elif CONFIG_TOTAL5200_REV==2 -# define CONFIG_SYS_FLASH_BASE 0xFA000000 -# define CONFIG_SYS_FLASH_SIZE 0x06000000 -#endif /* CONFIG_TOTAL5200_REV */ - -#if defined(CONFIG_SYS_LOWBOOT) -# define CONFIG_ENV_ADDR 0xFE040000 -#else /* CONFIG_SYS_LOWBOOT */ -# define CONFIG_ENV_ADDR 0xFFF40000 -#endif /* CONFIG_SYS_LOWBOOT */ - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x40000 -#define CONFIG_ENV_SECT_SIZE 0x40000 -#define CONFIG_ENV_OVERWRITE 1 - -/* - * Memory map - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 -#define CONFIG_SYS_MBAR 0xF0000000 /* 64 kB */ -#define CONFIG_SYS_FPGA_BASE 0xF0010000 /* 64 kB */ -#define CONFIG_SYS_CPLD_BASE 0xF0020000 /* 64 kB */ -#define CONFIG_SYS_LCD_BASE 0xF1000000 /* 4096 kB */ - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_SEVENWIRE -/* dummy, 7-wire FEC does not have phy address */ -#define CONFIG_PHY_ADDR 0x00 - -/* - * GPIO configuration - * - * CS1: SDRAM CS1 disabled, gpio_wkup_6 enabled 0 - * Reserved 0 - * ALTs: CAN1/2 on PSC2, SPI on PSC3 00 - * CS7: Interrupt GPIO on PSC3_5 0 - * CS8: Interrupt GPIO on PSC3_4 0 - * ATA: reset default, changed in ATA driver 00 - * IR_USB_CLK: IrDA/USB 48MHz clock gen. int., pin is GPIO 0 - * IRDA: reset default, changed in IrDA driver 000 - * ETHER: reset default, changed in Ethernet driver 0000 - * PCI_DIS: reset default, changed in PCI driver 0 - * USB_SE: reset default, changed in USB driver 0 - * USB: reset default, changed in USB driver 00 - * PSC3: SPI and UART functionality without CD 1100 - * Reserved 0 - * PSC2: CAN1/2 001 - * Reserved 0 - * PSC1: reset default, changed in AC'97 driver 000 - * - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x00000C10 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#if CONFIG_TOTAL5200_REV==1 -# define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -# define CONFIG_SYS_CS0_SIZE 0x02000000 /* 32 MB */ -#else -# define CONFIG_SYS_BOOTCS_START (CONFIG_SYS_CS4_START + CONFIG_SYS_CS4_SIZE) -# define CONFIG_SYS_BOOTCS_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_BOOTCS_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CONFIG_SYS_CS4_START (CONFIG_SYS_CS5_START + CONFIG_SYS_CS5_SIZE) -# define CONFIG_SYS_CS4_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_CS4_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -# define CONFIG_SYS_CS5_START CONFIG_SYS_FLASH_BASE -# define CONFIG_SYS_CS5_SIZE 0x02000000 /* 32 MB */ -# define CONFIG_SYS_CS5_CFG 0x0004DF00 /* 4WS, MX, AL, CE, AS_25, DS_32 */ -#endif - -#define CONFIG_SYS_CS1_START CONFIG_SYS_FPGA_BASE -#define CONFIG_SYS_CS1_SIZE 0x00010000 /* 64 kB */ -#define CONFIG_SYS_CS1_CFG 0x0019FF00 /* 25WS, MX, AL, AA, CE, AS_25, DS_32 */ - -#define CONFIG_SYS_CS2_START CONFIG_SYS_LCD_BASE -#define CONFIG_SYS_CS2_SIZE 0x00400000 /* 4096 kB */ -#define CONFIG_SYS_CS2_CFG 0x0032FD0C /* 50WS, MX, AL, AA, CE, AS_25, DS_16, endian swapping */ - -#if CONFIG_TOTAL5200_REV==1 -# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE -# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ -# define CONFIG_SYS_CS3_CFG 0x000ADF00 /* 10WS, MX, AL, CE, AS_25, DS_32 */ -#else -# define CONFIG_SYS_CS3_START CONFIG_SYS_CPLD_BASE -# define CONFIG_SYS_CS3_SIZE 0x00010000 /* 64 kB */ -# define CONFIG_SYS_CS3_CFG 0x000AD800 /* 10WS, MX, AL, CE, AS_24, DS_8 */ -#endif - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_ATA_CS_ON_I2C2 -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/ZUMA.h b/include/configs/ZUMA.h deleted file mode 100644 index cac6a677ba..0000000000 --- a/include/configs/ZUMA.h +++ /dev/null @@ -1,370 +0,0 @@ -/* - * (C) Copyright 2001 - * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_GT_6426x GT_64260 /* with a 64260 system controller */ -#define CONFIG_ETHER_PORT_MII /* use two MII ports */ -#define CONFIG_INTEL_LXT97X /* Intel LXT97X phy */ - -#ifndef __ASSEMBLY__ -#include <galileo/core.h> -#endif - -#include "../board/evb64260/local.h" - -#define CONFIG_EVB64260 1 /* this is an EVB64260 board */ -#define CONFIG_ZUMA_V2 1 /* always define this for ZUMA v2 */ - -#define CONFIG_SYS_TEXT_BASE 0xfff00000 - -/* #define CONFIG_ZUMA_V2_OLD 1 */ /* backwards compat for old V2 board */ - -#define CONFIG_BAUDRATE 38400 /* console baudrate = 38400 */ - -#define CONFIG_ECC /* enable ECC support */ - -#define CONFIG_750CX /* we have a 750CX/CXe (override local.h) */ - -/* which initialization functions to call for this board */ -#define CONFIG_MISC_INIT_R -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_SYS_BOARD_ASM_INIT - -#define CONFIG_SYS_BOARD_NAME "Zuma APv2" - -#define CONFIG_SYS_HUSH_PARSER - -/* - * The following defines let you select what serial you want to use - * for your console driver. - * - * what to do: - * to use the DUART, undef CONFIG_MPSC. If you have hacked a serial - * cable onto the second DUART channel, change the CONFIG_SYS_DUART port from 1 - * to 0 below. - * - * to use the MPSC, #define CONFIG_MPSC. If you have wired up another - * mpsc channel, change CONFIG_MPSC_PORT to the desired value. - */ -#define CONFIG_MPSC - -#define CONFIG_MPSC_PORT 0 - - -/* define this if you want to enable GT MAC filtering */ -#define CONFIG_GT_USE_MAC_HASH_TABLE - -#if 1 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#undef CONFIG_BOOTARGS - -#define CONFIG_BOOTCOMMAND \ - "tftpboot && " \ - "setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:" \ - "$netmask:$hostname:eth0:none panic=5 && bootm" - -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#undef CONFIG_ALTIVEC /* undef to disable */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - -#define CONFIG_MII /* enable MII commands */ - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BSP -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_DATE - - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor1=zuma-1,nor2=zuma-2" -#define MTDPARTS_DEFAULT "mtdparts=zuma-1:-(jffs2),zuma-2:-(user)" -*/ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00300000 /* default load address */ - -#define CONFIG_SYS_BUS_CLK 133000000 /* 133 MHz */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_RAM_LOCK - - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xfff00000 -#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ - -/* areas to map different things with the GT in physical space */ -#define CONFIG_SYS_DRAM_BANKS 4 -#define CONFIG_SYS_DFL_GT_REGS 0x14000000 /* boot time GT_REGS */ - -/* What to put in the bats. */ -#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000 - -/* Peripheral Device section */ -#define CONFIG_SYS_GT_REGS 0xf8000000 /* later mapped GT_REGS */ -#define CONFIG_SYS_DEV_BASE 0xf0000000 -#define CONFIG_SYS_DEV0_SIZE _64M /* zuma flash @ 0xf000.0000*/ -#define CONFIG_SYS_DEV1_SIZE _8M /* zuma IDE @ 0xf400.0000 */ -#define CONFIG_SYS_DEV2_SIZE _8M /* unused */ -#define CONFIG_SYS_DEV3_SIZE _8M /* unused */ - -#define CONFIG_SYS_DEV0_PAR 0xc498243c - /* c 4 9 8 2 4 3 c */ - /* 33 22|2222|22 22|111 1|11 11|1 1 | | */ - /* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */ - /* 11|00|0100|10 01|100|0 00|10 0|100 0|011 1|100 */ - /* 3| 0|.... ..| 1| 4 | 0 | 4 | 8 | 7 | 4 */ - -#define CONFIG_SYS_DEV1_PAR 0xc01b6ac5 - /* c 0 1 b 6 a c 5 */ - /* 33 22|2222|22 22|111 1|11 11|1 1 | | */ - /* 10 98|7654|32 10|987 6|54 32|1 098|7 654|3 210 */ - /* 11|00|0000|00 01|101|1 01|10 1|010 1|100 0|101 */ - /* 3| 0|.... ..| 1| 5 | 5 | 5 | 5 | 8 | 5 */ - - -#define CONFIG_SYS_8BIT_BOOT_PAR 0xc00b5e7c - -#define CONFIG_SYS_MPP_CONTROL_0 0x00007777 /* GPP[7:4] : REQ0[1:0] GNT0[1:0] */ -#define CONFIG_SYS_MPP_CONTROL_1 0x00000000 /* GPP[15:12] : GPP[11:8] */ -#define CONFIG_SYS_MPP_CONTROL_2 0x00008888 /* GPP[23:20] : REQ1[1:0] GNT1[1:0] */ -#define CONFIG_SYS_MPP_CONTROL_3 0x00000000 /* GPP[31:28] (int[3:0]) */ - /* GPP[27:24] (27 is int4, rest are GPP) */ - -#define CONFIG_SYS_SERIAL_PORT_MUX 0x00001101 /* 11=MPSC1/MPSC0 01=ETH, 0=only MII */ -#define CONFIG_SYS_GPP_LEVEL_CONTROL 0xf8000000 /* interrupt inputs: GPP[31:27] */ - -#define CONFIG_SYS_SDRAM_CONFIG 0xe4e18200 /* 0x448 */ - /* idmas use buffer 1,1 - comm use buffer 1 - pci use buffer 0,0 (pci1->0 pci0->0) - cpu use buffer 1 (R*18) - normal load (see also ifdef HVL) - standard SDRAM (see also ifdef REG) - non staggered refresh */ - /* 31:26 25 23 20 19 18 16 */ - /* 111001 00 111 0 0 00 1 */ - - /* refresh count=0x200 - phy interleave disable (by default, - set later by dram config..) - virt interleave enable */ - /* 15 14 13:0 */ - /* 1 0 0x200 */ - -#define CONFIG_SYS_DEV0_SPACE CONFIG_SYS_DEV_BASE -#define CONFIG_SYS_DEV1_SPACE (CONFIG_SYS_DEV0_SPACE + CONFIG_SYS_DEV0_SIZE) -#define CONFIG_SYS_DEV2_SPACE (CONFIG_SYS_DEV1_SPACE + CONFIG_SYS_DEV1_SIZE) -#define CONFIG_SYS_DEV3_SPACE (CONFIG_SYS_DEV2_SPACE + CONFIG_SYS_DEV2_SIZE) - -/*----------------------------------------------------------------------- - * PCI stuff - */ - -#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -/* PCI MEMORY MAP section */ -#define CONFIG_SYS_PCI0_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI0_MEM_SIZE _128M -#define CONFIG_SYS_PCI1_MEM_BASE 0x88000000 -#define CONFIG_SYS_PCI1_MEM_SIZE _128M - -#define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE) -#define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE) - -/* PCI I/O MAP section */ -#define CONFIG_SYS_PCI0_IO_BASE 0xfa000000 -#define CONFIG_SYS_PCI0_IO_SIZE _16M -#define CONFIG_SYS_PCI1_IO_BASE 0xfb000000 -#define CONFIG_SYS_PCI1_IO_SIZE _16M - -#define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE) -#define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000 -#define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE) -#define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000 - - -/*---------------------------------------------------------------------- - * Initial BAT mappings - */ - -/* NOTES: - * 1) GUARDED and WRITE_THRU not allowed in IBATS - * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT - */ - -/* SDRAM */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* init ram */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* PCI0, PCI1 memory space (starting at PCI0 base, mapped in one BAT) */ -#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS -#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -/* GT regs, bootrom, all the devices, PCI I/O */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M) -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ - - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 130 /* max number of sectors on one chip */ - -#define CONFIG_SYS_EXTRA_FLASH_DEVICE DEVICE0 /* extra flash at device 0 */ -#define CONFIG_SYS_EXTRA_FLASH_WIDTH 2 /* 16 bit */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_CFI 1 - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ -#define CONFIG_ENV_ADDR (0xfff80000 - CONFIG_ENV_SECT_SIZE) - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * L2CR setup -- make sure this is right for your board! - * look in include/74xx_7xx.h for the defines used here - */ - -#define CONFIG_SYS_L2 - -#ifdef CONFIG_750CX -#define L2_INIT 0 -#else -#define L2_INIT (L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \ - L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT) -#endif - -#define L2_ENABLE (L2_INIT | L2CR_L2E) - -/*------------------------------------------------------------------------ - * Real time clock - */ -#define CONFIG_RTC_DS1302 - - -/*------------------------------------------------------------------------ - * Galileo I2C driver - */ -#define CONFIG_GT_I2C - -#endif /* __CONFIG_H */ diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 0004750518..76ce7deb95 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -19,13 +19,11 @@ #include <configs/ti_am335x_common.h> #ifndef CONFIG_SPL_BUILD +#ifndef CONFIG_FIT # define CONFIG_FIT +#endif # define CONFIG_TIMESTAMP # define CONFIG_LZO -# ifdef CONFIG_ENABLE_VBOOT -# define CONFIG_FIT_SIGNATURE -# define CONFIG_RSA -# endif #endif #define CONFIG_SYS_BOOTM_LEN (16 << 20) diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index b00585c47b..7ccbf36b0b 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -39,6 +39,7 @@ #define CONFIG_POWER #define CONFIG_POWER_I2C #define CONFIG_POWER_TPS65218 +#define CONFIG_POWER_TPS62362 /* SPL defines. */ #define CONFIG_SPL_TEXT_BASE 0x40300350 @@ -235,6 +236,8 @@ "setenv fdtfile am437x-gp-evm.dtb; fi; " \ "if test $board_name = AM43__SK; then " \ "setenv fdtfile am437x-sk-evm.dtb; fi; " \ + "if test $board_name = AM43_IDK; then " \ + "setenv fdtfile am437x-idk-evm.dtb; fi; " \ "if test $fdtfile = undefined; then " \ "echo WARNING: Could not determine device tree; fi; \0" diff --git a/include/configs/arndale.h b/include/configs/arndale.h index d68993bb1f..3ad4a9ba91 100644 --- a/include/configs/arndale.h +++ b/include/configs/arndale.h @@ -51,8 +51,6 @@ /* PMIC */ #define CONFIG_PMIC #define CONFIG_POWER_I2C -#define CONFIG_POWER_MAX77686 - #define CONFIG_PREBOOT diff --git a/include/configs/chromebook_link.h b/include/configs/chromebook_link.h index 7e6d239d13..7b460e83c4 100644 --- a/include/configs/chromebook_link.h +++ b/include/configs/chromebook_link.h @@ -20,6 +20,7 @@ #define CONFIG_DCACHE_RAM_MRC_VAR_SIZE 0x4000 #define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MISC_INIT_R #define CONFIG_NR_DRAM_BANKS 8 #define CONFIG_X86_MRC_ADDR 0xfffa0000 @@ -63,6 +64,13 @@ #define CONFIG_CMD_CROS_EC #define CONFIG_ARCH_EARLY_INIT_R +#undef CONFIG_ENV_IS_NOWHERE +#undef CONFIG_ENV_SIZE +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_ENV_SECT_SIZE 0x1000 +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x003f8000 + #define CONFIG_STD_DEVICES_SETTINGS "stdin=usbkbd,vga,serial\0" \ "stdout=vga,serial\0" \ "stderr=vga,serial\0" diff --git a/include/configs/corvus.h b/include/configs/corvus.h index 5b50c1d6dd..ace511f765 100644 --- a/include/configs/corvus.h +++ b/include/configs/corvus.h @@ -18,6 +18,7 @@ #define MACH_TYPE_CORVUS 2066 +#define CONFIG_MACH_TYPE MACH_TYPE_CORVUS #define CONFIG_SYS_GENERIC_BOARD /* * Warning: changing CONFIG_SYS_TEXT_BASE requires @@ -106,6 +107,7 @@ /* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8 #endif /* Ethernet */ @@ -171,7 +173,6 @@ #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_GPIO_SUPPORT -#define CONFIG_SYS_NAND_ENABLE_PIN_SPL (2*32 + 14) #define CONFIG_SPL_NAND_SUPPORT #define CONFIG_SPL_NAND_DRIVERS #define CONFIG_SPL_NAND_BASE @@ -184,7 +185,6 @@ #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_SIZE (256*1024*1024) #define CONFIG_SYS_NAND_PAGE_SIZE 2048 #define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) #define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ diff --git a/include/configs/cpci5200.h b/include/configs/cpci5200.h deleted file mode 100644 index ec926fd22d..0000000000 --- a/include/configs/cpci5200.h +++ /dev/null @@ -1,390 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - - */ - -/************************************************************************* - * (c) 2005 esd gmbh Hannover - * - * - * from IceCube.h file - * by Reinhard Arlt reinhard.arlt@esd-electronics.com - * - *************************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_ICECUBE 1 /* ... on IceCube board */ -#define CONFIG_CPCI5200 1 /* ... on CPCI5200 board */ -#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */ -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#if 1 -#define CONFIG_PCI 1 -#if 1 -#define CONFIG_PCI_PNP 1 -#endif -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 -#endif - -#define CONFIG_MII -#if 0 /* test-only !!! */ -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 -#endif - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* USB */ -#if 0 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#endif - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_IDE -#define CONFIG_CMD_I2C -#define CONFIG_CMD_BSP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_DATE - -#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT16 1 -#endif -#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT08 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Welcome to esd CPU CPCI/5200;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \ - "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \ - "net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \ - "vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \ - "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \ - "loadaddr=01000000\0" \ - "serverip=192.168.2.99\0" \ - "gatewayip=10.0.0.79\0" \ - "user=mu\0" \ - "target=cpci5200.esd\0" \ - "script=cpci5200.bat\0" \ - "image=/tftpboot/vxWorks_cpci5200\0" \ - "ipaddr=10.0.13.196\0" \ - "netmask=255.255.0.0\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_vxworks0" - -#define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfd010000 -#define CONFIG_SYS_NVRAM_SIZE 32*1024 - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 -/* - * Flash configuration - */ - -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#define CONFIG_SYS_FLASH_INCREMENT 0x01000000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000) -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 - -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* - * Environment settings - */ -#if 1 /* test-only */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x20000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_OVERWRITE 1 -#else -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */ - /* total size of a CAT24WC32 is 8192 bytes */ -#define CONFIG_ENV_OVERWRITE 1 -#endif - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_FEC_10MBIT to force FEC at 10Mb - */ -/* #define CONFIG_FEC_10MBIT 1 */ -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_UDP_CHECKSUM 1 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00 - -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS1_START 0xfd000000 -#define CONFIG_SYS_CS1_SIZE 0x00010000 -#define CONFIG_SYS_CS1_CFG 0x10101410 - -#define CONFIG_SYS_CS3_START 0xfd010000 -#define CONFIG_SYS_CS3_SIZE 0x00010000 -#define CONFIG_SYS_CS3_CFG 0x10109410 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -/*----------------------------------------------------------------------- - * CPLD stuff - */ -#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */ -#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */ - -/* CPLD program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */ -#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */ - -#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */ -#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */ -#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */ -#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */ - -#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00) -#define JTAG_GPIO_CFG_SET 0x00000000 -#define JTAG_GPIO_CFG_RESET 0x00F00000 - -#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04) -#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */ -#define JTAG_GPIO_TMS_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C) -#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */ -#define JTAG_GPIO_TMS_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00) -#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */ -#define JTAG_GPIO_TCK_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08) -#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */ -#define JTAG_GPIO_TCK_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00) -#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */ -#define JTAG_GPIO_TDI_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08) -#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */ -#define JTAG_GPIO_TDI_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04) -#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */ -#define JTAG_GPIO_TDO_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C) -#define JTAG_GPIO_TDO_DDR_SET 0x00000000 -#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index 77e2f587bd..1c69551d16 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -16,12 +16,8 @@ #define __CONFIG_H /* High Level Configuration Options */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ #define CONFIG_OMAP3_DEVKIT8000 1 /* working with DevKit8000 */ #define CONFIG_MACH_TYPE MACH_TYPE_DEVKIT8000 -#define CONFIG_OMAP_GPIO -#define CONFIG_OMAP_COMMON -#define CONFIG_SYS_GENERIC_BOARD /* * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM @@ -31,31 +27,31 @@ */ #define CONFIG_SYS_TEXT_BASE 0x80100000 -#define CONFIG_SDRC /* The chip has SDRC controller */ +#define CONFIG_SPL_BSS_START_ADDR 0x80000500 /* leave space for bootargs*/ +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 + +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ + +#define CONFIG_NAND + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ -#include <asm/arch/cpu.h> /* get chip and board defs */ -#include <asm/arch/omap3.h> +#include <configs/ti_omap3_common.h> /* Display CPU and Board information */ #define CONFIG_DISPLAY_CPUINFO 1 #define CONFIG_DISPLAY_BOARDINFO 1 -/* Clock Defines */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - #define CONFIG_MISC_INIT_R -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 #define CONFIG_REVISION_TAG 1 -#define CONFIG_OF_LIBFDT 1 - /* Size of malloc() pool */ #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */ /* Sector */ +#undef CONFIG_SYS_MALLOC_LEN #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) /* Hardware drivers */ @@ -69,39 +65,18 @@ #define CONFIG_DM9000_NO_SROM 1 #undef CONFIG_DM9000_DEBUG -/* NS16550 Configuration */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -/* select serial console configuration */ -#define CONFIG_CONS_INDEX 3 -#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 -#define CONFIG_SERIAL3 3 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ - 115200} - -/* MMC */ -#define CONFIG_GENERIC_MMC 1 -#define CONFIG_MMC 1 -#define CONFIG_OMAP_HSMMC 1 -#define CONFIG_DOS_PARTITION 1 +/* SPI */ +#undef CONFIG_SPI +#undef CONFIG_OMAP3_SPI /* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 -#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#undef CONFIG_SYS_I2C_OMAP24XX #define CONFIG_SYS_I2C_OMAP34XX /* TWL4030 */ -#define CONFIG_TWL4030_POWER 1 #define CONFIG_TWL4030_LED 1 /* Board NAND Info */ -#define CONFIG_SYS_NO_FLASH /* no NOR flash */ -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ #define MTDIDS_DEFAULT "nand0=nand" #define MTDPARTS_DEFAULT "mtdparts=nand:" \ "512k(x-loader)," \ @@ -110,14 +85,8 @@ "4m(kernel)," \ "-(fs)" -#define CONFIG_NAND_OMAP_GPMC #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ /* to access nand */ -#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ - /* to access nand at */ - /* CS0 */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ - /* devices */ #define CONFIG_JFFS2_NAND /* nand device jffs2 lives on */ #define CONFIG_JFFS2_DEV "nand0" @@ -127,20 +96,20 @@ /* partition */ /* commands to include */ -#include <config_cmd_default.h> - #define CONFIG_CMD_DHCP /* DHCP support */ -#define CONFIG_CMD_EXT2 /* EXT2 Support */ -#define CONFIG_CMD_FAT /* FAT support */ -#define CONFIG_CMD_I2C /* I2C serial bus support */ #define CONFIG_CMD_JFFS2 /* JFFS2 Support */ -#define CONFIG_CMD_MMC /* MMC support */ -#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ -#define CONFIG_CMD_NAND /* NAND support */ #define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */ #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ #undef CONFIG_CMD_IMI /* iminfo */ +#undef CONFIG_CMD_SPI +#undef CONFIG_CMD_GPIO +#undef CONFIG_CMD_ASKENV +#undef CONFIG_CMD_BOOTZ +#undef CONFIG_SUPPORT_RAW_INITRD +#undef CONFIG_FAT_WRITE +#undef CONFIG_CMD_EXT4 +#undef CONFIG_CMD_FS_GENERIC /* BOOTP/DHCP options */ #define CONFIG_BOOTP_SUBNETMASK @@ -157,10 +126,6 @@ #undef CONFIG_BOOTP_VENDOREX /* Environment information */ -#define CONFIG_ENV_OVERWRITE /* allow to overwrite serial and ethaddr */ - -#define CONFIG_BOOTDELAY 3 - #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ "console=ttyO2,115200n8\0" \ @@ -228,88 +193,29 @@ #define CONFIG_BOOTCOMMAND "run autoboot" -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ -#define CONFIG_AUTO_COMPLETE 1 -#define CONFIG_SYS_PROMPT "OMAP3 DevKit8000 # " -#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 128 /* max number of command args */ - /* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) - #define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0 + 0x07000000) #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ 0x01000000) /* 16MB */ -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0 + 0x02000000) - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/* Physical Memory Map */ -#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - /* NAND and environment organization */ -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ - #define CONFIG_ENV_IS_IN_NAND 1 #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - /* SRAM config */ #define CONFIG_SYS_SRAM_START 0x40200000 #define CONFIG_SYS_SRAM_SIZE 0x10000 /* Defines for SPL */ -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_NAND_SIMPLE - -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBDISK_SUPPORT -#define CONFIG_SPL_BOARD_INIT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT -#define CONFIG_SPL_POWER_SUPPORT -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SPL_MMC_SUPPORT -#define CONFIG_SPL_FAT_SUPPORT -#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" -#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#undef CONFIG_SPL_MTD_SUPPORT +#undef CONFIG_SPL_TEXT_BASE #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ -#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ +#undef CONFIG_SPL_STACK #define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK -#define CONFIG_SPL_BSS_START_ADDR 0x80000500 /* leave space for bootargs*/ -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 - /* NAND boot config */ #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16 #define CONFIG_SYS_NAND_5_ADDR_CYCLE @@ -325,30 +231,23 @@ #define CONFIG_SYS_NAND_ECCBYTES 3 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE - #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #define CONFIG_SYS_NAND_U_BOOT_SIZE 0x200000 -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* 1 MB */ - /* SPL OS boot options */ -#define CONFIG_SPL_OS_BOOT - -#define CONFIG_CMD_SPL #define CONFIG_CMD_SPL_WRITE_SIZE 0x400 /* 1024 byte */ #define CONFIG_CMD_SPL_NAND_OFS (CONFIG_SYS_NAND_SPL_KERNEL_OFFS+\ 0x400000) #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000 -#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" -#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" - +#undef CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR +#undef CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR +#undef CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x500 /* address 0xa0000 */ #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x8 /* address 0x1000 */ #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 8 /* 4KB */ +#undef CONFIG_SYS_SPL_ARGS_ADDR #define CONFIG_SYS_SPL_ARGS_ADDR (PHYS_SDRAM_1 + 0x100) #endif /* __CONFIG_H */ diff --git a/include/configs/dockstar.h b/include/configs/dockstar.h index 46a42b3087..ec7f721ff3 100644 --- a/include/configs/dockstar.h +++ b/include/configs/dockstar.h @@ -12,6 +12,8 @@ #ifndef _CONFIG_DOCKSTAR_H #define _CONFIG_DOCKSTAR_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ diff --git a/include/configs/exynos5-common.h b/include/configs/exynos5-common.h index ad63f3c549..0ba39a23dd 100644 --- a/include/configs/exynos5-common.h +++ b/include/configs/exynos5-common.h @@ -126,12 +126,11 @@ #define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) /* I2C */ -#define CONFIG_SYS_I2C_INIT_BOARD -#define CONFIG_SYS_I2C +#define CONFIG_DM_I2C +#define CONFIG_DM_I2C_COMPAT #define CONFIG_CMD_I2C -#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */ #define CONFIG_SYS_I2C_S3C24X0 -#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 /* 100 Kbps */ #define CONFIG_SYS_I2C_S3C24X0_SLAVE 0x0 #define CONFIG_I2C_EDID diff --git a/include/configs/exynos5250-common.h b/include/configs/exynos5250-common.h index 671431397f..ae0e5ff47b 100644 --- a/include/configs/exynos5250-common.h +++ b/include/configs/exynos5250-common.h @@ -28,9 +28,6 @@ #define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK -/* PMIC */ -#define CONFIG_POWER_MAX77686 - /* Sound */ #define CONFIG_CMD_SOUND #ifdef CONFIG_CMD_SOUND diff --git a/include/configs/goflexhome.h b/include/configs/goflexhome.h index 5ed949791f..836515d178 100644 --- a/include/configs/goflexhome.h +++ b/include/configs/goflexhome.h @@ -15,6 +15,8 @@ #ifndef _CONFIG_GOFLEXHOME_H #define _CONFIG_GOFLEXHOME_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ diff --git a/include/configs/guruplug.h b/include/configs/guruplug.h index a56a4cb982..8e53af8c04 100644 --- a/include/configs/guruplug.h +++ b/include/configs/guruplug.h @@ -1,5 +1,6 @@ /* - * (C) Copyright 2009 + * (C) Copyright 2009-2014 + * Gerald Kerma <dreagle@doukki.net> * Marvell Semiconductor <www.marvell.com> * Written-by: Siddarth Gore <gores@marvell.com> * @@ -9,6 +10,8 @@ #ifndef _CONFIG_GURUPLUG_H #define _CONFIG_GURUPLUG_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ @@ -23,17 +26,36 @@ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ /* + * Compression configuration + */ +#define CONFIG_BZIP2 +#define CONFIG_LZMA +#define CONFIG_LZO + +/* + * Enable device tree support + */ +#define CONFIG_OF_LIBFDT + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ + +/* * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ #include <config_cmd_default.h> +#define CONFIG_CMD_BOOTZ #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV -#define CONFIG_CMD_FAT +#define CONFIG_CMD_IDE +#define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_PING #define CONFIG_CMD_USB -#define CONFIG_CMD_IDE +#define CONFIG_CMD_FAT /* * mv-common.h should be defined after CMD configs since it used them @@ -55,24 +77,38 @@ * it has to be rounded to sector size */ #define CONFIG_ENV_SIZE 0x20000 /* 128k */ -#define CONFIG_ENV_ADDR 0x60000 -#define CONFIG_ENV_OFFSET 0x60000 /* env starts here */ +#define CONFIG_ENV_OFFSET 0xE0000 /* env starts here */ /* * Default environment variables */ -#define CONFIG_BOOTCOMMAND "setenv ethact egiga0; " \ - "${x_bootcmd_ethernet}; setenv ethact egiga1; " \ - "${x_bootcmd_ethernet}; ${x_bootcmd_usb}; ${x_bootcmd_kernel}; "\ - "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \ - "bootm 0x6400000;" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "x_bootcmd_ethernet=ping 192.168.2.1\0" \ - "x_bootcmd_usb=usb start\0" \ - "x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000\0" \ - "x_bootargs=console=ttyS0,115200\0" \ - "x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0" +#define CONFIG_BOOTCOMMAND \ + "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \ + "ubi part root; " \ + "ubifsmount ubi:rootfs; " \ + "ubifsload 0x800000 ${kernel}; " \ + "ubifsload 0x700000 ${fdt}; " \ + "ubifsumount; " \ + "fdt addr 0x700000; fdt resize; fdt chosen; " \ + "bootz 0x800000 - 0x700000" + +#define CONFIG_MTDPARTS \ + "mtdparts=orion_nand:" \ + "896K(uboot),128K(uboot_env)," \ + "-@1M(root)\0" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "console=console=ttyS0,115200\0" \ + "mtdids=nand0=orion_nand\0" \ + "mtdparts="CONFIG_MTDPARTS \ + "kernel=/boot/zImage\0" \ + "fdt=/boot/guruplug-server-plus.dtb\0" \ + "bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rw\0" + +#define MTDIDS_DEFAULT "nand0=orion_nand" + +#define MTDPARTS_DEFAULT \ + "mtdparts="CONFIG_MTDPARTS /* * Ethernet Driver configuration @@ -89,6 +125,20 @@ #define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET #endif /*CONFIG_MVSATA_IDE*/ +/* + * File system + */ +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_RBTREE +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_MTDPARTS + #define CONFIG_SYS_ALT_MEMTEST #endif /* _CONFIG_GURUPLUG_H */ diff --git a/include/configs/ib62x0.h b/include/configs/ib62x0.h index f4c748a91d..f1ddf21580 100644 --- a/include/configs/ib62x0.h +++ b/include/configs/ib62x0.h @@ -9,6 +9,8 @@ #ifndef _CONFIG_IB62x0_H #define _CONFIG_IB62x0_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ diff --git a/include/configs/iconnect.h b/include/configs/iconnect.h index 9f4a4b83a3..2baf50cc4e 100644 --- a/include/configs/iconnect.h +++ b/include/configs/iconnect.h @@ -9,6 +9,8 @@ #ifndef _CONFIG_ICONNECT_H #define _CONFIG_ICONNECT_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h index f08483487d..2384864eb0 100644 --- a/include/configs/ids8313.h +++ b/include/configs/ids8313.h @@ -575,12 +575,9 @@ #define CONFIG_VERSION_VARIABLE -#define CONFIG_FIT -#define CONFIG_FIT_SIGNATURE #define CONFIG_IMAGE_FORMAT_LEGACY #define CONFIG_CMD_FDT #define CONFIG_CMD_HASH -#define CONFIG_RSA #define CONFIG_SHA1 #define CONFIG_SHA256 diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h index 8dc04f2e57..2874ccc6fa 100644 --- a/include/configs/ls1021aqds.h +++ b/include/configs/ls1021aqds.h @@ -19,6 +19,11 @@ #define CONFIG_SKIP_LOWLEVEL_INIT #define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DEEP_SLEEP +#if defined(CONFIG_DEEP_SLEEP) +#define CONFIG_SILENT_CONSOLE +#endif + /* * Size of malloc() pool */ @@ -72,7 +77,8 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_SPL_PAD_TO 0x1c000 #define CONFIG_SYS_TEXT_BASE 0x82000000 -#define CONFIG_SYS_SPL_MALLOC_START 0x80200000 +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ + CONFIG_SYS_MONITOR_LEN) #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 @@ -365,11 +371,16 @@ unsigned long get_board_ddr_clk(void); /* * Serial Port */ +#ifdef CONFIG_LPUART +#define CONFIG_FSL_LPUART +#define CONFIG_LPUART_32B_REG +#else #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() +#endif #define CONFIG_BAUDRATE 115200 @@ -385,6 +396,7 @@ unsigned long get_board_ddr_clk(void); */ #define I2C_MUX_PCA_ADDR_PRI 0x77 #define I2C_MUX_CH_DEFAULT 0x8 +#define I2C_MUX_CH_CH7301 0xC /* * MMC @@ -427,6 +439,25 @@ unsigned long get_board_ddr_clk(void); #endif /* + * Video + */ +#define CONFIG_FSL_DCU_FB + +#ifdef CONFIG_FSL_DCU_FB +#define CONFIG_VIDEO +#define CONFIG_CMD_BMP +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO + +#define CONFIG_FSL_DIU_CH7301 +#define CONFIG_SYS_I2C_DVI_BUS_NUM 0 +#define CONFIG_SYS_I2C_QIXIS_ADDR 0x66 +#define CONFIG_SYS_I2C_DVI_ADDR 0x75 +#endif + +/* * eTSEC */ #define CONFIG_TSEC_ENET @@ -508,11 +539,19 @@ unsigned long get_board_ddr_clk(void); #define CONFIG_SYS_QE_FW_ADDR 0x67f40000 +#ifdef CONFIG_LPUART +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ + "fdt_high=0xcfffffff\0" \ + "initrd_high=0xcfffffff\0" \ + "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=null\0" +#else #define CONFIG_EXTRA_ENV_SETTINGS \ "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ "fdt_high=0xcfffffff\0" \ "initrd_high=0xcfffffff\0" \ "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=null\0" +#endif /* * Miscellaneous configurable options diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h index 66954d0a40..0a0bb5f109 100644 --- a/include/configs/ls1021atwr.h +++ b/include/configs/ls1021atwr.h @@ -186,11 +186,16 @@ /* * Serial Port */ +#ifdef CONFIG_LPUART +#define CONFIG_FSL_LPUART +#define CONFIG_LPUART_32B_REG +#else #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_serial_clock() +#endif #define CONFIG_BAUDRATE 115200 @@ -325,10 +330,17 @@ #define CONFIG_BOOTDELAY 3 +#ifdef CONFIG_LPUART +#define CONFIG_EXTRA_ENV_SETTINGS \ + "bootargs=root=/dev/ram0 rw console=ttyLP0,115200\0" \ + "initrd_high=0xcfffffff\0" \ + "fdt_high=0xcfffffff\0" +#else #define CONFIG_EXTRA_ENV_SETTINGS \ "bootargs=root=/dev/ram0 rw console=ttyS0,115200\0" \ "initrd_high=0xcfffffff\0" \ "fdt_high=0xcfffffff\0" +#endif /* * Miscellaneous configurable options diff --git a/include/configs/malta.h b/include/configs/malta.h index a29b86b4f6..354672ecf8 100644 --- a/include/configs/malta.h +++ b/include/configs/malta.h @@ -38,8 +38,6 @@ #define CONFIG_SYS_MHZ 250 /* arbitrary value */ #define CONFIG_SYS_MIPS_TIMER_FREQ (CONFIG_SYS_MHZ * 1000000) -#define CONFIG_SWAP_IO_SPACE - /* * Memory map */ @@ -73,6 +71,7 @@ sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_HUSH_PARSER #define CONFIG_AUTO_COMPLETE #define CONFIG_CMDLINE_EDITING @@ -109,6 +108,16 @@ (CONFIG_SYS_FLASH_BASE + (4 << 20) - CONFIG_ENV_SIZE) /* + * IDE/ATA + */ +#define CONFIG_SYS_IDE_MAXBUS 1 +#define CONFIG_SYS_IDE_MAXDEVICE 2 +#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01f0 +#define CONFIG_SYS_ATA_DATA_OFFSET 0 +#define CONFIG_SYS_ATA_REG_OFFSET 0 + +/* * Commands */ #include <config_cmd_default.h> @@ -120,6 +129,8 @@ #define CONFIG_CMD_DATE #define CONFIG_CMD_DHCP +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IDE #define CONFIG_CMD_PCI #define CONFIG_CMD_PING diff --git a/include/configs/mecp5200.h b/include/configs/mecp5200.h deleted file mode 100644 index b270429dd8..0000000000 --- a/include/configs/mecp5200.h +++ /dev/null @@ -1,319 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - - -/************************************************************************* - * (c) 2005 esd gmbh Hannover - * - * - * from IceCube.h file - * by Reinhard Arlt reinhard.arlt@esd-electronics.com - * - *************************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_ICECUBE 1 /* ... on IceCube board */ -#define CONFIG_MECP5200 1 /* ... on MECP5200 board */ -#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#if 0 /* test-only */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#else -#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */ -#endif -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#define CONFIG_MII -#if 0 /* test-only !!! */ -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 -#endif - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* USB */ -#if 0 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_BSP -#define CONFIG_CMD_ELF - - -#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT16 1 -#endif -#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT08 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Welcome to CBX-CPU5200 (mecp5200);" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \ - "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \ - "net_vxworks=tftp $(loadaddr) $(image);run vxworks_args;bootvx\0" \ - "vxworks_args=setenv bootargs fec(0,0)$(host):$(image) h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script)\0" \ - "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=$(serverip) e=$(ipaddr) g=$(gatewayip) u=$(user) $(pass) tn=$(target) s=$(script) o=fec0 \0" \ - "loadaddr=01000000\0" \ - "serverip=192.168.2.99\0" \ - "gatewayip=10.0.0.79\0" \ - "user=mu\0" \ - "target=mecp5200.esd\0" \ - "script=mecp5200.bat\0" \ - "image=/tftpboot/vxWorks_mecp5200\0" \ - "ipaddr=10.0.13.196\0" \ - "netmask=255.255.0.0\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_vxworks0" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xFFC00000 -#define CONFIG_SYS_FLASH_SIZE 0x00400000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x003E0000) -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* - * Environment settings - */ -#if 1 /* test-only */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_OVERWRITE 1 -#else -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars*/ - /* total size of a CAT24WC32 is 8192 bytes */ -#define CONFIG_ENV_OVERWRITE 1 -#endif - -#define CONFIG_FLASH_CFI_DRIVER 1 /* Flash is CFI conformant */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware protection */ -#if 0 -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#endif -#define CONFIG_SYS_FLASH_INCREMENT 0x00400000 /* size of flash bank */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_FLASH_EMPTY_INFO 1 /* show if bank is empty */ - - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_UDP_CHECKSUM 1 - - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00085d00 - -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS1_START 0xfd000000 -#define CONFIG_SYS_CS1_SIZE 0x00010000 -#define CONFIG_SYS_CS1_CFG 0x10101410 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#endif /* __CONFIG_H */ diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h deleted file mode 100644 index 0308c52bc7..0000000000 --- a/include/configs/mpc7448hpc2.h +++ /dev/null @@ -1,386 +0,0 @@ -/* - * Copyright (c) 2005 Freescale Semiconductor, Inc. - * - * (C) Copyright 2006 - * Alex Bounine , Tundra Semiconductor Corp. - * Roy Zang , <tie-fei.zang@freescale.com> Freescale Corp. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board specific configuration options for Freescale - * MPC7448HPC2 (High-Performance Computing II) (Taiga) board - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* Board Configuration Definitions */ -/* MPC7448HPC2 (High-Performance Computing II) (Taiga) board */ - -#define CONFIG_MPC7448HPC2 - -#define CONFIG_74xx -#define CONFIG_HIGH_BATS /* High BATs supported */ -#define CONFIG_ALTIVEC /* undef to disable */ - -#define CONFIG_SYS_TEXT_BASE 0xFF000000 - -#define CONFIG_SYS_BOARD_NAME "MPC7448 HPC II" -#define CONFIG_IDENT_STRING " Freescale MPC7448 HPC II" - -#define CONFIG_SYS_OCN_CLK 133000000 /* 133 MHz */ -#define CONFIG_SYS_BUS_CLK 133000000 - -#define CONFIG_SYS_CLK_SPREAD /* Enable Spread-Spectrum Clock generation */ - -#undef CONFIG_ECC /* disable ECC support */ - -#ifndef __ASSEMBLY__ -#include <galileo/core.h> -#endif - -/* Board-specific Initialization Functions to be called */ -#define CONFIG_SYS_BOARD_ASM_INIT -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_BOARD_EARLY_INIT_R -#define CONFIG_MISC_INIT_R - -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 - -#define CONFIG_ENV_OVERWRITE - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_BAUDRATE 115200 /* console baudrate = 115000 */ - -/*#define CONFIG_SYS_HUSH_PARSER */ -#undef CONFIG_SYS_HUSH_PARSER - - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_TSI "tsi108@c0000000" -#define OF_TBCLK (bd->bi_busfreq / 8) -#define OF_STDOUT_PATH "/tsi108@c0000000/serial@7808" - -/* - * The following defines let you select what serial you want to use - * for your console driver. - * - * what to do: - * If you have hacked a serial cable onto the second DUART channel, - * change the CONFIG_SYS_DUART port from 1 to 0 below. - * - */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_OCN_CLK * 8 - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_TSI108_CSR_RST_BASE+0x7808) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_TSI108_CSR_RST_BASE+0x7C08) - -#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */ -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#undef CONFIG_BOOTARGS -/* #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo" */ - -#if (CONFIG_BOOTDELAY >= 0) -#define CONFIG_BOOTCOMMAND "tftpboot 0x400000 zImage.initrd.elf;\ - setenv bootargs $(bootargs) $(bootargs_root) nfsroot=$(serverip):$(rootpath) \ - ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000; " - -#define CONFIG_BOOTARGS "console=ttyS0,115200" -#endif - -#undef CONFIG_EXTRA_ENV_SETTINGS - -#define CONFIG_SERIAL "No. 1" - -/* Networking Configuration */ - -#define CONFIG_TSI108_ETH -#define CONFIG_TSI108_ETH_NUM_PORTS 2 - - -#define CONFIG_BOOTFILE "zImage.initrd.elf" -#define CONFIG_LOADADDR 0x400000 - -/*-------------------------------------------------------------------------- */ - -#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate changes */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_PCI -#define CONFIG_CMD_I2C -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_CMD_DATE - - -/*set date in u-boot*/ -#define CONFIG_RTC_M48T35A -#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 -#define CONFIG_SYS_NVRAM_SIZE 0x8000 -/* - * Miscellaneous configurable options - */ -#define CONFIG_VERSION_VARIABLE 1 -#define CONFIG_TSI108_I2C -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* I2C EEPROM page 1 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)/* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00400000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ - -/* - * When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS - * To an unused memory region. The stack will remain in cache until RAM - * is initialized - */ -#undef CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0x07d00000 /* unused memory region */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000/* larger space - we have SDRAM initialized */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* first 256 MB of SDRAM */ -#define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* next 256MB of SDRAM */ - -#define CONFIG_SYS_SDRAM2_BASE 0x40000000 /* beginning of non-cacheable alias for SDRAM - first 256MB */ -#define CONFIG_SYS_SDRAM3_BASE 0x50000000 /* next Non-Cacheable 256MB of SDRAM */ - -#define CONFIG_SYS_PCI_PFM_BASE 0x80000000 /* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */ - -#define CONFIG_SYS_PCI_MEM32_BASE 0xE0000000 /* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */ - -#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000 /* Base Address for (PCI/X + Flash) region */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* Base Address of Flash device */ -#define CONFIG_SYS_FLASH_BASE2 0xfe000000 /* Alternate Flash Base Address */ - -#define CONFIG_VERY_BIG_RAM /* we will use up to 256M memory for cause we are short of BATS */ - -#define PCI0_IO_BASE_BOOTM 0xfd000000 - -#define CONFIG_SYS_RESET_ADDRESS 0x3fffff00 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* u-boot code base */ -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */ - -/* Peripheral Device section */ - -/* - * Resources on the Tsi108 - */ - -#define CONFIG_SYS_TSI108_CSR_RST_BASE 0xC0000000 /* Tsi108 CSR base after reset */ -#define CONFIG_SYS_TSI108_CSR_BASE CONFIG_SYS_TSI108_CSR_RST_BASE /* Runtime Tsi108 CSR base */ - -#define ENABLE_PCI_CSR_BAR /* enables access to Tsi108 CSRs from the PCI/X bus */ - -#undef DISABLE_PBM - -/* - * PCI stuff - * - */ - -#define CONFIG_PCI /* include pci support */ -#define CONFIG_TSI108_PCI /* include tsi108 pci support */ - -#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ -#define PCI_HOST_FORCE 1 /* configure as pci host */ -#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ - -#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ - -/* PCI MEMORY MAP section */ - -/* PCI view of System Memory */ -#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000 - -/* PCI Memory Space */ -#define CONFIG_SYS_PCI_MEM_BUS (CONFIG_SYS_PCI_MEM_PHYS) -#define CONFIG_SYS_PCI_MEM_PHYS (CONFIG_SYS_PCI_MEM32_BASE) /* 0xE0000000 */ -#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256 MB space for PCI/X Mem + SDRAM OCN */ - -/* PCI I/O Space */ -#define CONFIG_SYS_PCI_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI_IO_PHYS 0xfa000000 /* Changed from fd000000 */ - -#define CONFIG_SYS_PCI_IO_SIZE 0x01000000 /* 16MB */ - -/* PCI Config Space mapping */ -#define CONFIG_SYS_PCI_CFG_BASE 0xfb000000 /* Changed from FE000000 */ -#define CONFIG_SYS_PCI_CFG_SIZE 0x01000000 /* 16MB */ - -#define CONFIG_SYS_IBAT0U 0xFE0003FF -#define CONFIG_SYS_IBAT0L 0xFE000002 - -#define CONFIG_SYS_IBAT1U 0x00007FFF -#define CONFIG_SYS_IBAT1L 0x00000012 - -#define CONFIG_SYS_IBAT2U 0x80007FFF -#define CONFIG_SYS_IBAT2L 0x80000022 - -#define CONFIG_SYS_IBAT3U 0x00000000 -#define CONFIG_SYS_IBAT3L 0x00000000 - -#define CONFIG_SYS_IBAT4U 0x00000000 -#define CONFIG_SYS_IBAT4L 0x00000000 - -#define CONFIG_SYS_IBAT5U 0x00000000 -#define CONFIG_SYS_IBAT5L 0x00000000 - -#define CONFIG_SYS_IBAT6U 0x00000000 -#define CONFIG_SYS_IBAT6L 0x00000000 - -#define CONFIG_SYS_IBAT7U 0x00000000 -#define CONFIG_SYS_IBAT7L 0x00000000 - -#define CONFIG_SYS_DBAT0U 0xE0003FFF -#define CONFIG_SYS_DBAT0L 0xE000002A - -#define CONFIG_SYS_DBAT1U 0x00007FFF -#define CONFIG_SYS_DBAT1L 0x00000012 - -#define CONFIG_SYS_DBAT2U 0x00000000 -#define CONFIG_SYS_DBAT2L 0x00000000 - -#define CONFIG_SYS_DBAT3U 0xC0000003 -#define CONFIG_SYS_DBAT3L 0xC000002A - -#define CONFIG_SYS_DBAT4U 0x00000000 -#define CONFIG_SYS_DBAT4L 0x00000000 - -#define CONFIG_SYS_DBAT5U 0x00000000 -#define CONFIG_SYS_DBAT5L 0x00000000 - -#define CONFIG_SYS_DBAT6U 0x00000000 -#define CONFIG_SYS_DBAT6L 0x00000000 - -#define CONFIG_SYS_DBAT7U 0x00000000 -#define CONFIG_SYS_DBAT7L 0x00000000 - -/* I2C addresses for the two DIMM SPD chips */ -#define DIMM0_I2C_ADDR 0x51 -#define DIMM1_I2C_ADDR 0x52 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Flash can be at one of two addresses */ -#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */ -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, /* CONFIG_SYS_FLASH_BASE2 */ } - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_WRITE_SWAPPED_DATA - -#define PHYS_FLASH_SIZE 0x01000000 -#define CONFIG_SYS_MAX_FLASH_SECT (128) - -#define CONFIG_ENV_IS_IN_NVRAM -#define CONFIG_ENV_ADDR 0xFC000000 - -#define CONFIG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x00000400 /* Total Size of Environment Space */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * L2CR setup -- make sure this is right for your board! - * look in include/mpc74xx.h for the defines used here - */ -#undef CONFIG_SYS_L2 - -#define L2_INIT 0 -#define L2_ENABLE (L2_INIT | L2CR_L2E) -#define CONFIG_SYS_SERIAL_HANG_IN_EXCEPTION -#endif /* __CONFIG_H */ diff --git a/include/configs/odroid.h b/include/configs/odroid.h index 807e96bbaa..9d5dbdce36 100644 --- a/include/configs/odroid.h +++ b/include/configs/odroid.h @@ -177,12 +177,11 @@ /* I2C */ #define CONFIG_CMD_I2C -#define CONFIG_SYS_I2C +#define CONFIG_DM_I2C +#define CONFIG_DM_I2C_COMPAT #define CONFIG_SYS_I2C_S3C24X0 #define CONFIG_SYS_I2C_S3C24X0_SPEED 100000 #define CONFIG_SYS_I2C_S3C24X0_SLAVE 0 -#define CONFIG_MAX_I2C_NUM 8 -#define CONFIG_SYS_I2C_INIT_BOARD /* POWER */ #define CONFIG_POWER diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 7d102a4699..c0bb227a33 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -45,6 +45,9 @@ "root=${mmcroot} " \ "rootfstype=${mmcrootfstype}\0" \ "bootenv=uEnv.txt\0" \ + "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \ + "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \ + "source ${loadaddr}\0" \ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ "importbootenv=echo Importing environment from mmc ...; " \ "env import -t $loadaddr $filesize\0" \ @@ -65,17 +68,21 @@ #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev}; if mmc rescan; then " \ "echo SD/MMC found on device ${mmcdev};" \ - "if run loadbootenv; then " \ - "echo Loaded environment from ${bootenv};" \ - "run importbootenv;" \ - "fi;" \ - "if test -n $uenvcmd; then " \ - "echo Running uenvcmd ...;" \ - "run uenvcmd;" \ - "fi;" \ - "if run loaduimage; then " \ - "run mmcboot;" \ - "fi;" \ + "if run loadbootscript; then " \ + "run bootscript;" \ + "else " \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loaduimage; then " \ + "run mmcboot;" \ + "fi;" \ + "fi ;" \ "fi;" \ /* Clock Defines */ diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h deleted file mode 100644 index be76478c30..0000000000 --- a/include/configs/pf5200.h +++ /dev/null @@ -1,372 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************* - * (c) 2005 esd gmbh Hannover - * - * - * from IceCube.h file - * by Reinhard Arlt reinhard.arlt@esd-electronics.com - * - *************************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_ICECUBE 1 /* ... on IceCube board */ -#define CONFIG_PF5200 1 /* ... on PF5200 board */ -#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#if 0 /* test-only */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#else -#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */ -#endif -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_MII 1 -#if 0 /* test-only !!! */ -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 -#endif - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* USB */ -#if 0 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE - -#define CONFIG_CMD_PCI - - -#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT16 1 -#endif -#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT08 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Welcome to ParaFinder pf5200;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \ - "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \ - "net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \ - "vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \ - "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \ - "loadaddr=01000000\0" \ - "serverip=192.168.2.99\0" \ - "gatewayip=10.0.0.79\0" \ - "user=mu\0" \ - "target=pf5200.esd\0" \ - "script=pf5200.bat\0" \ - "image=/tftpboot/vxWorks_pf5200\0" \ - "ipaddr=10.0.13.196\0" \ - "netmask=255.255.0.0\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_vxworks0" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000) -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* - * Environment settings - */ -#if 1 /* test-only */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_OVERWRITE 1 -#else -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */ - /* total size of a CAT24WC32 is 8192 bytes */ -#define CONFIG_ENV_OVERWRITE 1 -#endif - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_UDP_CHECKSUM 1 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00 - -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS1_START 0xfd000000 -#define CONFIG_SYS_CS1_SIZE 0x00010000 -#define CONFIG_SYS_CS1_CFG 0x10101410 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -/*----------------------------------------------------------------------- - * CPLD stuff - */ -#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */ -#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */ - -/* CPLD program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */ -#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */ - -#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */ -#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */ -#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */ -#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */ - -#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00) -#define JTAG_GPIO_CFG_SET 0x00000000 -#define JTAG_GPIO_CFG_RESET 0x00F00000 - -#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04) -#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */ -#define JTAG_GPIO_TMS_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C) -#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */ -#define JTAG_GPIO_TMS_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00) -#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */ -#define JTAG_GPIO_TCK_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08) -#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */ -#define JTAG_GPIO_TCK_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00) -#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */ -#define JTAG_GPIO_TDI_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08) -#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */ -#define JTAG_GPIO_TDI_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04) -#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */ -#define JTAG_GPIO_TDO_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C) -#define JTAG_GPIO_TDO_DDR_SET 0x00000000 -#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/pogo_e02.h b/include/configs/pogo_e02.h index 7594bdb412..89560ad1c5 100644 --- a/include/configs/pogo_e02.h +++ b/include/configs/pogo_e02.h @@ -13,6 +13,8 @@ #ifndef _CONFIG_POGO_E02_H #define _CONFIG_POGO_E02_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Machine type definition and ID */ diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h deleted file mode 100644 index 18f9a6cc20..0000000000 --- a/include/configs/ppmc7xx.h +++ /dev/null @@ -1,416 +0,0 @@ -/* - * ppmc7xx.h - * --------- - * - * Wind River PPMC 7xx/74xx board configuration file. - * - * By Richard Danter (richard.danter@windriver.com) - * Copyright (C) 2005 Wind River Systems - */ - - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_PPMC7XX - - -/*=================================================================== - * - * User configurable settings - Modify to your preference - * - *=================================================================== - */ - -/* - * Debug - * - * DEBUG - Define this is you want extra debug info - * GTREGREAD - Required to build with debug - * do_bdinfo - Required to build with debug - */ - -#ifdef DEBUG -#define GTREGREAD(x) 0xFFFFFFFF -#define do_bdinfo(a,b,c,d) -#endif - -/* - * CPU type - * - * CONFIG_7xx - We have a 750 or 755 CPU - * CONFIG_74xx - We have a 7400 CPU - * CONFIG_ALTIVEC - We have altivec enabled CPU (only 7400) - * CONFIG_BUS_CLK - System bus clock in Hz - */ - -#define CONFIG_7xx -#undef CONFIG_74xx -#undef CONFIG_ALTIVEC -#define CONFIG_BUS_CLK 66000000 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#ifndef __ASSEMBLY__ -#include <galileo/core.h> -#endif - -/* - * Monitor configuration - * - * List of command sets to include in shell - * - * The following command sets have been tested and known to work: - * - * CMD_CACHE - Cache control commands - * CMD_MEMORY - Memory display, change and test commands - * CMD_FLASH - Erase and program flash - * CMD_ENV - Environment commands - * CMD_RUN - Run commands stored in env vars - * CMD_ELF - Load ELF files - * CMD_NET - Networking/file download commands - * CMD_PIN - ICMP Echo Request command - * CMD_PCI - PCI Bus scanning command - */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_RUN -#define CONFIG_CMD_ELF -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_PCI - -#undef CONFIG_CMD_KGDB - - -/* - * Serial configuration - * - * CONFIG_CONS_INDEX - Serial console port number (COM1) - * CONFIG_BAUDRATE - Serial speed - */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 9600 - - -/* - * PCI config - * - * CONFIG_PCI - Enable PCI bus - * CONFIG_PCI_PNP - Enable Plug & Play support - * CONFIG_PCI_SCAN_SHOW - Enable display of devices at startup - */ - -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_PCI_PNP -#undef CONFIG_PCI_SCAN_SHOW - - -/* - * Network config - * - * CONFIG_EEPRO100 - Intel 8255x Ethernet Controller - * CONFIG_EEPRO100_SROM_WRITE - Enable writing to network card ROM - */ - -#define CONFIG_EEPRO100 -#define CONFIG_EEPRO100_SROM_WRITE - - -/* - * Enable extra init functions - * - * CONFIG_MISC_INIT_F - Call pre-relocation init functions - * CONFIG_MISC_INIT_R - Call post relocation init functions - */ - -#undef CONFIG_MISC_INIT_F -#define CONFIG_MISC_INIT_R - - -/* - * Boot config - * - * CONFIG_BOOTCOMMAND - Command(s) to execute to auto-boot - * CONFIG_BOOTDELAY - How long to wait before auto-boot (in sec) - */ - -#define CONFIG_BOOTCOMMAND \ - "bootp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ - "bootm" -#define CONFIG_BOOTDELAY 5 - - -/*=================================================================== - * - * Board configuration settings - You should not need to modify these - * - *=================================================================== - */ - - -/* - * Memory map - * - * This board runs in a standard CHRP (Map-B) configuration. - * - * Type Start End Size Width Chip Sel - * ----------- ----------- ----------- ------- ------- -------- - * SDRAM 0x00000000 0x04000000 64MB 64b SDRAMCS0 - * User LED's 0x78000000 RCS3 - * UART 0x7C000000 RCS2 - * Mailbox 0xFF000000 RCS1 - * Flash 0xFFC00000 0xFFFFFFFF 4MB 64b RCS0 - * - * Flash sectors are laid out as follows. - * - * Sector Start End Size Comments - * ------- ----------- ----------- ------- ----------- - * 0 0xFFC00000 0xFFC3FFFF 256KB - * 1 0xFFC40000 0xFFC7FFFF 256KB - * 2 0xFFC80000 0xFFCBFFFF 256KB - * 3 0xFFCC0000 0xFFCFFFFF 256KB - * 4 0xFFD00000 0xFFD3FFFF 256KB - * 5 0xFFD40000 0xFFD7FFFF 256KB - * 6 0xFFD80000 0xFFDBFFFF 256KB - * 7 0xFFDC0000 0xFFDFFFFF 256KB - * 8 0xFFE00000 0xFFE3FFFF 256KB - * 9 0xFFE40000 0xFFE7FFFF 256KB - * 10 0xFFE80000 0xFFEBFFFF 256KB - * 11 0xFFEC0000 0xFFEFFFFF 256KB - * 12 0xFFF00000 0xFFF3FFFF 256KB U-Boot code here - * 13 0xFFF40000 0xFFF7FFFF 256KB - * 14 0xFFF80000 0xFFFBFFFF 256KB - * 15 0xFFFC0000 0xFFFDFFFF 128KB - * 16 0xFFFE0000 0xFFFE7FFF 32KB U-Boot env vars here - * 17 0xFFFE8000 0xFFFEFFFF 32KB U-Boot backup copy of env vars here - * 18 0xFFFF0000 0xFFFFFFFF 64KB - */ - - -/* - * SDRAM config - see memory map details above. - * - * CONFIG_SYS_SDRAM_BASE - Start address of SDRAM, this _must_ be zero! - * CONFIG_SYS_SDRAM_SIZE - Total size of contiguous SDRAM bank(s) - */ - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 0x04000000 - - -/* - * Flash config - see memory map details above. - * - * CONFIG_SYS_FLASH_BASE - Start address of flash memory - * CONFIG_SYS_FLASH_SIZE - Total size of contiguous flash mem - * CONFIG_SYS_FLASH_ERASE_TOUT - Erase timeout in ms - * CONFIG_SYS_FLASH_WRITE_TOUT - Write timeout in ms - * CONFIG_SYS_MAX_FLASH_BANKS - Number of banks of flash on board - * CONFIG_SYS_MAX_FLASH_SECT - Number of sectors in a bank - */ - -#define CONFIG_SYS_FLASH_BASE 0xFFC00000 -#define CONFIG_SYS_FLASH_SIZE 0x00400000 -#define CONFIG_SYS_FLASH_ERASE_TOUT 250000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 5000 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 128 - - -/* - * Monitor config - see memory map details above - * - * CONFIG_SYS_MONITOR_BASE - Base address of monitor code - * CONFIG_SYS_MALLOC_LEN - Size of malloc pool (128KB) - */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MALLOC_LEN 0x20000 - - -/* - * Command shell settings - * - * CONFIG_SYS_BARGSIZE - Boot Argument buffer size - * CONFIG_SYS_BOOTMAPSZ - Size of app's mapped RAM at boot (Linux=8MB) - * CONFIG_SYS_CBSIZE - Console Buffer (input) size - * CONFIG_SYS_LOAD_ADDR - Default load address - * CONFIG_SYS_LONGHELP - Provide more detailed help - * CONFIG_SYS_MAXARGS - Number of args accepted by monitor commands - * CONFIG_SYS_MEMTEST_START - Start address of test to run on RAM - * CONFIG_SYS_MEMTEST_END - End address of RAM test - * CONFIG_SYS_PBSIZE - Print Buffer (output) size - * CONFIG_SYS_PROMPT - Prompt string - */ - -#define CONFIG_SYS_BARGSIZE 1024 -#define CONFIG_SYS_BOOTMAPSZ 0x800000 -#define CONFIG_SYS_CBSIZE 1024 -#define CONFIG_SYS_LOAD_ADDR 0x100000 -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_MEMTEST_START 0x00040000 -#define CONFIG_SYS_MEMTEST_END 0x00040100 -#define CONFIG_SYS_PBSIZE 1024 - - -/* - * Environment config - see memory map details above - * - * CONFIG_ENV_IS_IN_FLASH - The env variables are stored in flash - * CONFIG_ENV_ADDR - Address of the sector containing env vars - * CONFIG_ENV_SIZE - Ammount of RAM for env vars (used to save RAM, 4KB) - * CONFIG_ENV_SECT_SIZE - Size of sector containing env vars (32KB) - */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFFFE0000 -#define CONFIG_ENV_SIZE 0x1000 -#define CONFIG_ENV_ADDR_REDUND 0xFFFE8000 -#define CONFIG_ENV_SIZE_REDUND 0x1000 -#define CONFIG_ENV_SECT_SIZE 0x8000 - - -/* - * Initial RAM config - * - * Since the main system RAM is initialised very early, we place the INIT_RAM - * in the main system RAM just above the exception vectors. The contents are - * copied to top of RAM by the init code. - * - * CONFIG_SYS_INIT_RAM_ADDR - Address of Init RAM, above exception vect - * CONFIG_SYS_INIT_RAM_SIZE - Size of Init RAM - * GENERATED_GBL_DATA_SIZE - Ammount of RAM to reserve for global data - * CONFIG_SYS_GBL_DATA_OFFSET - Start of global data, top of stack - */ - -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + 0x4000) -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - - -/* - * Initial BAT config - * - * BAT0 - System SDRAM - * BAT1 - LED's and Serial Port - * BAT2 - PCI Memory - * BAT3 - PCI I/O including Flash Memory - */ - -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -#define CONFIG_SYS_IBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - - -/* - * Cache config - * - * CONFIG_SYS_CACHELINE_SIZE - Size of a cache line (CPU specific) - * CONFIG_SYS_L2 - L2 cache enabled if defined - * L2_INIT - L2 cache init flags - * L2_ENABLE - L2 cache enable flags - */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 -#undef CONFIG_SYS_L2 -#define L2_INIT 0 -#define L2_ENABLE 0 - - -/* - * Clocks config - * - * CONFIG_SYS_BUS_CLK - Bus clock frequency in Hz - * CONFIG_SYS_HZ - Decrementer freq in Hz - */ - -#define CONFIG_SYS_BUS_CLK CONFIG_BUS_CLK - - -/* - * Serial port config - * - * CONFIG_SYS_NS16550 - Include the NS16550 driver - * CONFIG_SYS_NS16550_SERIAL - Include the serial (wrapper) driver - * CONFIG_SYS_NS16550_CLK - Frequency of reference clock - * CONFIG_SYS_NS16550_REG_SIZE - 64-bit accesses to 8-bit port - * CONFIG_SYS_NS16550_COM1 - Base address of 1st serial port - */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_CLK 3686400 -#define CONFIG_SYS_NS16550_REG_SIZE -8 -#define CONFIG_SYS_NS16550_COM1 0x7C000000 - - -/* - * PCI Config - Address Map B (CHRP) - */ - -#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000 -#define CONFIG_SYS_PCI_MEMORY_SIZE 0x40000000 -#define CONFIG_SYS_PCI_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI_MEM_SIZE 0x7D000000 -#define CONFIG_SYS_ISA_MEM_BUS 0x00000000 -#define CONFIG_SYS_ISA_MEM_PHYS 0xFD000000 -#define CONFIG_SYS_ISA_MEM_SIZE 0x01000000 -#define CONFIG_SYS_PCI_IO_BUS 0x00800000 -#define CONFIG_SYS_PCI_IO_PHYS 0xFE800000 -#define CONFIG_SYS_PCI_IO_SIZE 0x00400000 -#define CONFIG_SYS_ISA_IO_BUS 0x00000000 -#define CONFIG_SYS_ISA_IO_PHYS 0xFE000000 -#define CONFIG_SYS_ISA_IO_SIZE 0x00800000 -#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_ISA_IO_PHYS -#define CONFIG_SYS_ISA_IO CONFIG_SYS_ISA_IO_PHYS -#define CONFIG_SYS_60X_PCI_IO_OFFSET CONFIG_SYS_ISA_IO_PHYS - - -/* - * Extra init functions - * - * CONFIG_SYS_BOARD_ASM_INIT - Call assembly init code - */ - -#define CONFIG_SYS_BOARD_ASM_INIT - -#endif /* __CONFIG_H */ diff --git a/include/configs/sama5d3_xplained.h b/include/configs/sama5d3_xplained.h index d5588b1241..9458047c06 100644 --- a/include/configs/sama5d3_xplained.h +++ b/include/configs/sama5d3_xplained.h @@ -246,6 +246,7 @@ #define CONFIG_SYS_NAND_OOBSIZE 64 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 +#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER #endif diff --git a/include/configs/sama5d4_xplained.h b/include/configs/sama5d4_xplained.h index 104edef102..996973d99b 100644 --- a/include/configs/sama5d4_xplained.h +++ b/include/configs/sama5d4_xplained.h @@ -121,6 +121,14 @@ #define CONFIG_USB_STORAGE #endif +/* USB device */ +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_ATMEL_USBA +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETH_RNDIS +#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK" + #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION diff --git a/include/configs/sama5d4ek.h b/include/configs/sama5d4ek.h index cbdb3a2943..09ab4d7f25 100644 --- a/include/configs/sama5d4ek.h +++ b/include/configs/sama5d4ek.h @@ -121,6 +121,14 @@ #define CONFIG_USB_STORAGE #endif +/* USB device */ +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_ATMEL_USBA +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETH_RNDIS +#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK" + #if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION diff --git a/include/configs/sandbox.h b/include/configs/sandbox.h index 657f751f3c..e9d3f3226b 100644 --- a/include/configs/sandbox.h +++ b/include/configs/sandbox.h @@ -23,7 +23,6 @@ #define CONFIG_BOOTSTAGE #define CONFIG_BOOTSTAGE_REPORT -#define CONFIG_DM #define CONFIG_CMD_DEMO #define CONFIG_CMD_DM #define CONFIG_DM_DEMO @@ -41,9 +40,6 @@ #define CONFIG_OF_LIBFDT #define CONFIG_LMB -#define CONFIG_FIT -#define CONFIG_FIT_SIGNATURE -#define CONFIG_RSA #define CONFIG_CMD_FDT #define CONFIG_ANDROID_BOOT_IMAGE diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h index 71be823899..21c8bda9f3 100644 --- a/include/configs/sheevaplug.h +++ b/include/configs/sheevaplug.h @@ -10,6 +10,8 @@ #ifndef _CONFIG_SHEEVAPLUG_H #define _CONFIG_SHEEVAPLUG_H +#define CONFIG_SYS_GENERIC_BOARD + /* * Version number information */ diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h index 83953728dd..3b06d305db 100644 --- a/include/configs/smdk5250.h +++ b/include/configs/smdk5250.h @@ -18,6 +18,8 @@ #include <configs/exynos5250-common.h> +/* PMIC */ +#define CONFIG_POWER_MAX77686 #define CONFIG_BOARD_COMMON #define CONFIG_ARCH_EARLY_INIT_R diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h index 942af2e7f6..9fa644f7c2 100644 --- a/include/configs/snapper9260.h +++ b/include/configs/snapper9260.h @@ -34,7 +34,6 @@ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_SKIP_LOWLEVEL_INIT -#define CONFIG_SKIP_RELOCATE_UBOOT #define CONFIG_DISPLAY_CPUINFO #define CONFIG_FIT diff --git a/include/configs/snow.h b/include/configs/snow.h index 7eaa58697e..ce6676eae7 100644 --- a/include/configs/snow.h +++ b/include/configs/snow.h @@ -22,6 +22,7 @@ #define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */ #define CONFIG_POWER_TPS65090_I2C +#define CONFIG_DM_CROS_EC #define CONFIG_BOARD_COMMON #define CONFIG_ARCH_EARLY_INIT_R diff --git a/include/configs/sun4i.h b/include/configs/sun4i.h index 7b857405e9..87d269b041 100644 --- a/include/configs/sun4i.h +++ b/include/configs/sun4i.h @@ -13,7 +13,6 @@ */ #define CONFIG_CLK_FULL_SPEED 1008000000 -#define CONFIG_SYS_PROMPT "sun4i# " #define CONFIG_MACH_TYPE 4104 #ifdef CONFIG_USB_EHCI diff --git a/include/configs/sun5i.h b/include/configs/sun5i.h index 09f7533575..52e3a6ff01 100644 --- a/include/configs/sun5i.h +++ b/include/configs/sun5i.h @@ -13,7 +13,6 @@ */ #define CONFIG_CLK_FULL_SPEED 1008000000 -#define CONFIG_SYS_PROMPT "sun5i# " #define CONFIG_MACH_TYPE 4138 #ifdef CONFIG_USB_EHCI diff --git a/include/configs/sun6i.h b/include/configs/sun6i.h index 1b73852799..f5e11ddb69 100644 --- a/include/configs/sun6i.h +++ b/include/configs/sun6i.h @@ -16,8 +16,6 @@ */ #define CONFIG_CLK_FULL_SPEED 1008000000 -#define CONFIG_SYS_PROMPT "sun6i# " - #ifdef CONFIG_USB_EHCI #define CONFIG_USB_EHCI_SUNXI #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 diff --git a/include/configs/sun7i.h b/include/configs/sun7i.h index ccec50c328..7cd7890341 100644 --- a/include/configs/sun7i.h +++ b/include/configs/sun7i.h @@ -14,7 +14,6 @@ */ #define CONFIG_CLK_FULL_SPEED 912000000 -#define CONFIG_SYS_PROMPT "sun7i# " #define CONFIG_MACH_TYPE 4283 #ifdef CONFIG_USB_EHCI diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h index f16e60b576..3bdedb390c 100644 --- a/include/configs/sun8i.h +++ b/include/configs/sun8i.h @@ -14,8 +14,6 @@ */ #define CONFIG_CLK_FULL_SPEED 1008000000 -#define CONFIG_SYS_PROMPT "sun8i# " - #ifdef CONFIG_USB_EHCI #define CONFIG_USB_EHCI_SUNXI #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h index e839053e2b..6cfd7e1489 100644 --- a/include/configs/sunxi-common.h +++ b/include/configs/sunxi-common.h @@ -40,6 +40,8 @@ */ #define CONFIG_DISPLAY_CPUINFO +#define CONFIG_SYS_PROMPT "sunxi# " + /* Serial & console */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL @@ -179,7 +181,10 @@ #define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000 /* 512 KiB */ /* I2C */ +#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER #define CONFIG_SPL_I2C_SUPPORT +#endif + #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MVTWSI #define CONFIG_SYS_I2C_SPEED 400000 @@ -247,8 +252,16 @@ #endif #ifdef CONFIG_USB_EHCI -#define CONFIG_CMD_USB #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1 +#endif + +#ifdef CONFIG_USB_MUSB_SUNXI +#define CONFIG_MUSB_HOST +#define CONFIG_MUSB_PIO_ONLY +#endif + +#if defined CONFIG_USB_EHCI || defined CONFIG_USB_MUSB_SUNXI +#define CONFIG_CMD_USB #define CONFIG_USB_STORAGE #endif diff --git a/include/configs/taurus.h b/include/configs/taurus.h index 20194aebb5..65468ad165 100644 --- a/include/configs/taurus.h +++ b/include/configs/taurus.h @@ -26,6 +26,11 @@ #define CONFIG_SYS_GENERIC_BOARD +#if defined(CONFIG_SPL_BUILD) +#define CONFIG_SYS_THUMB_BUILD +#define CONFIG_SYS_ICACHE_OFF +#define CONFIG_SYS_DCACHE_OFF +#endif /* * Warning: changing CONFIG_SYS_TEXT_BASE requires * adapting the initial boot program. @@ -137,6 +142,19 @@ #define TAURUS_SPI_MASK (1 << 4) #define TAURUS_SPI_CS_PIN AT91_PIN_PA3 +#if defined(CONFIG_SPL_BUILD) +/* SPL related */ +#undef CONFIG_SPL_OS_BOOT /* Not supported by existing map */ +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 + +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#endif + /* load address */ #define CONFIG_SYS_LOAD_ADDR 0x22000000 @@ -171,8 +189,11 @@ /* Defines for SPL */ #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_TEXT_BASE 0x0 -#define CONFIG_SPL_MAX_SIZE (11 * 1024) +#define CONFIG_SPL_MAX_SIZE (14 * 1024) #define CONFIG_SPL_STACK (16 * 1024) +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \ + CONFIG_SYS_MALLOC_LEN) +#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN #define CONFIG_SPL_BSS_START_ADDR CONFIG_SPL_MAX_SIZE #define CONFIG_SPL_BSS_MAX_SIZE (3 * 1024) diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 5ed86d9365..598526bf95 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -20,7 +20,9 @@ #define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC #ifndef CONFIG_SPL_BUILD +#ifndef CONFIG_DM # define CONFIG_DM +#endif # define CONFIG_CMD_DM # define CONFIG_DM_GPIO # define CONFIG_DM_SERIAL diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h index c47651d796..925cb42dd3 100644 --- a/include/configs/ti_omap5_common.h +++ b/include/configs/ti_omap5_common.h @@ -85,10 +85,16 @@ "vram=${vram} " \ "root=${mmcroot} " \ "rootfstype=${mmcrootfstype}\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \ "source ${loadaddr}\0" \ - "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \ "env import -t ${loadaddr} ${filesize}\0" \ "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ @@ -110,6 +116,13 @@ "bootz ${loadaddr} - ${fdtaddr}; " \ "fi;" \ "fi;\0" \ + "netboot=echo Booting from network ...; " \ + "set env autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "tftp ${fdtaddr} ${fdtfile}; " \ + "run netargs; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ "findfdt="\ "if test $board_name = omap5_uevm; then " \ "setenv fdtfile omap5-uevm.dtb; fi; " \ diff --git a/include/configs/uniphier.h b/include/configs/uniphier.h index 5a53c506c3..9ad47f6933 100644 --- a/include/configs/uniphier.h +++ b/include/configs/uniphier.h @@ -43,6 +43,9 @@ #define CONFIG_SDRAM1_SIZE 0x10000000 #endif +#define CONFIG_I2C_EEPROM +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + /* * Support card address map */ diff --git a/include/configs/vexpress_aemv8a.h b/include/configs/vexpress_aemv8a.h index 027d78b591..7fb28a54ba 100644 --- a/include/configs/vexpress_aemv8a.h +++ b/include/configs/vexpress_aemv8a.h @@ -11,9 +11,9 @@ /* We use generic board for v8 Versatile Express */ #define CONFIG_SYS_GENERIC_BOARD -#ifdef CONFIG_BASE_FVP +#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP #ifndef CONFIG_SEMIHOSTING -#error CONFIG_BASE_FVP requires CONFIG_SEMIHOSTING +#error CONFIG_TARGET_VEXPRESS64_BASE_FVP requires CONFIG_SEMIHOSTING #endif #define CONFIG_BOARD_LATE_INIT #define CONFIG_ARMV8_SWITCH_TO_EL1 @@ -21,8 +21,9 @@ #define CONFIG_REMAKE_ELF -#ifndef CONFIG_BASE_FVP -/* Base FVP not using GICv3 yet */ +#if !defined(CONFIG_TARGET_VEXPRESS64_BASE_FVP) && \ + !defined(CONFIG_TARGET_VEXPRESS64_JUNO) +/* Base FVP and Juno not using GICv3 yet */ #define CONFIG_GICV3 #endif @@ -40,10 +41,13 @@ #define CONFIG_BOOTP_VCI_STRING "U-boot.armv8.vexpress_aemv8a" /* Link Definitions */ -#ifdef CONFIG_BASE_FVP +#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP /* ATF loads u-boot here for BASE_FVP model */ #define CONFIG_SYS_TEXT_BASE 0x88000000 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x03f00000) +#elif CONFIG_TARGET_VEXPRESS64_JUNO +#define CONFIG_SYS_TEXT_BASE 0xe0000000 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) #else #define CONFIG_SYS_TEXT_BASE 0x80000000 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) @@ -54,7 +58,7 @@ /* SMP Spin Table Definitions */ -#ifdef CONFIG_BASE_FVP +#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP #define CPU_RELEASE_ADDR (CONFIG_SYS_SDRAM_BASE + 0x03f00000) #else #define CPU_RELEASE_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0) @@ -88,10 +92,15 @@ #define V2M_KMI0 (V2M_PA_CS3 + V2M_PERIPH_OFFSET(6)) #define V2M_KMI1 (V2M_PA_CS3 + V2M_PERIPH_OFFSET(7)) +#ifdef CONFIG_TARGET_VEXPRESS64_JUNO +#define V2M_UART0 0x7ff80000 +#define V2M_UART1 0x7ff70000 +#else /* Not Juno */ #define V2M_UART0 (V2M_PA_CS3 + V2M_PERIPH_OFFSET(9)) #define V2M_UART1 (V2M_PA_CS3 + V2M_PERIPH_OFFSET(10)) #define V2M_UART2 (V2M_PA_CS3 + V2M_PERIPH_OFFSET(11)) #define V2M_UART3 (V2M_PA_CS3 + V2M_PERIPH_OFFSET(12)) +#endif #define V2M_WDT (V2M_PA_CS3 + V2M_PERIPH_OFFSET(15)) @@ -119,9 +128,12 @@ #define GICR_BASE (0x2f100000) #else -#ifdef CONFIG_BASE_FVP +#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP #define GICD_BASE (0x2f000000) #define GICC_BASE (0x2c000000) +#elif CONFIG_TARGET_VEXPRESS64_JUNO +#define GICD_BASE (0x2C010000) +#define GICC_BASE (0x2C02f000) #else #define GICD_BASE (0x2C001000) #define GICC_BASE (0x2C002000) @@ -140,7 +152,11 @@ /* PL011 Serial Configuration */ #define CONFIG_PL011_SERIAL +#ifdef CONFIG_TARGET_VEXPRESS64_JUNO +#define CONFIG_PL011_CLOCK 7273800 +#else #define CONFIG_PL011_CLOCK 24000000 +#endif #define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ (void *)CONFIG_SYS_SERIAL1} #define CONFIG_CONS_INDEX 0 @@ -161,6 +177,7 @@ #define CONFIG_CMD_ENV #define CONFIG_CMD_FLASH #define CONFIG_CMD_IMI +#define CONFIG_CMD_LOADB #define CONFIG_CMD_MEMORY #define CONFIG_CMD_MII #define CONFIG_CMD_NET @@ -191,7 +208,7 @@ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 /* Initial environment variables */ -#ifdef CONFIG_BASE_FVP +#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP #define CONFIG_EXTRA_ENV_SETTINGS \ "kernel_name=uImage\0" \ "kernel_addr_r=0x80000000\0" \ diff --git a/include/configs/vexpress_common.h b/include/configs/vexpress_common.h index 7e78f8ac8f..2dea921045 100644 --- a/include/configs/vexpress_common.h +++ b/include/configs/vexpress_common.h @@ -122,7 +122,7 @@ #define CONFIG_SETUP_MEMORY_TAGS 1 #define CONFIG_SYS_L2CACHE_OFF 1 #define CONFIG_INITRD_TAG 1 - +#define CONFIG_SYS_GENERIC_BOARD #define CONFIG_OF_LIBFDT 1 /* Size of malloc() pool */ diff --git a/include/configs/x86-common.h b/include/configs/x86-common.h index f16ae32913..ecedfc3ab1 100644 --- a/include/configs/x86-common.h +++ b/include/configs/x86-common.h @@ -179,6 +179,7 @@ #define VIDEO_FB_16BPP_WORD_SWAP #define CONFIG_I8042_KBD #define CONFIG_CFB_CONSOLE +#define CONFIG_CONSOLE_SCROLL_LINES 5 /*----------------------------------------------------------------------- * CPU Features @@ -210,6 +211,7 @@ #define CONFIG_CMD_SF_TEST #define CONFIG_CMD_SPI #define CONFIG_SPI +#define CONFIG_OF_SPI_FLASH /*----------------------------------------------------------------------- * Environment configuration diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h index 87b4fffeb9..864528a5ea 100644 --- a/include/configs/zynq-common.h +++ b/include/configs/zynq-common.h @@ -47,6 +47,17 @@ # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN # define CONFIG_PHYLIB # define CONFIG_PHY_MARVELL +# define CONFIG_BOOTP_SERVERIP +# define CONFIG_BOOTP_BOOTPATH +# define CONFIG_BOOTP_GATEWAY +# define CONFIG_BOOTP_HOSTNAME +# define CONFIG_BOOTP_MAY_FAIL +# if !defined(CONFIG_ZYNQ_GEM_EMIO0) +# define CONFIG_ZYNQ_GEM_EMIO0 0 +# endif +# if !defined(CONFIG_ZYNQ_GEM_EMIO1) +# define CONFIG_ZYNQ_GEM_EMIO1 0 +# endif #endif /* SPI */ @@ -90,6 +101,55 @@ # define CONFIG_USB_ULPI # define CONFIG_EHCI_IS_TDI # define CONFIG_USB_MAX_CONTROLLER_COUNT 2 + +# define CONFIG_CI_UDC /* ChipIdea CI13xxx UDC */ +# define CONFIG_USB_GADGET +# define CONFIG_USB_GADGET_DUALSPEED +# define CONFIG_USBDOWNLOAD_GADGET +# define CONFIG_SYS_DFU_DATA_BUF_SIZE 0x600000 +# define DFU_DEFAULT_POLL_TIMEOUT 300 +# define CONFIG_DFU_FUNCTION +# define CONFIG_DFU_RAM +# define CONFIG_USB_GADGET_VBUS_DRAW 2 +# define CONFIG_G_DNL_VENDOR_NUM 0x03FD +# define CONFIG_G_DNL_PRODUCT_NUM 0x0300 +# define CONFIG_G_DNL_MANUFACTURER "Xilinx" +# define CONFIG_USB_GADGET +# define CONFIG_USB_CABLE_CHECK +# define CONFIG_CMD_DFU +# define CONFIG_CMD_THOR_DOWNLOAD +# define CONFIG_THOR_FUNCTION +# define DFU_ALT_INFO_RAM \ + "dfu_ram_info=" \ + "set dfu_alt_info " \ + "${kernel_image} ram 0x3000000 0x500000\\\\;" \ + "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \ + "${ramdisk_image} ram 0x2000000 0x600000\0" \ + "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \ + "thor_ram=run dfu_ram_info && thordown 0 ram 0\0" + +# if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1) +# define CONFIG_DFU_MMC +# define DFU_ALT_INFO_MMC \ + "dfu_mmc_info=" \ + "set dfu_alt_info " \ + "${kernel_image} fat 0 1\\\\;" \ + "${devicetree_image} fat 0 1\\\\;" \ + "${ramdisk_image} fat 0 1\0" \ + "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \ + "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0" + +# define DFU_ALT_INFO \ + DFU_ALT_INFO_RAM \ + DFU_ALT_INFO_MMC +# else +# define DFU_ALT_INFO \ + DFU_ALT_INFO_RAM +# endif +#endif + +#if !defined(DFU_ALT_INFO) +# define DFU_ALT_INFO #endif #if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB) @@ -100,6 +160,7 @@ # define CONFIG_DOS_PARTITION # define CONFIG_CMD_EXT4 # define CONFIG_CMD_EXT4_WRITE +# define CONFIG_CMD_FS_GENERIC #endif #define CONFIG_SYS_I2C_ZYNQ @@ -121,12 +182,6 @@ # define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */ #endif -#define CONFIG_BOOTP_SERVERIP -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_MAY_FAIL - /* Total Size of Environment Sector */ #define CONFIG_ENV_SIZE (128 << 10) @@ -159,16 +214,17 @@ "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \ "bootm ${load_addr}\0" \ "sdboot=echo Copying FIT from SD to RAM... && " \ - "fatload mmc 0 ${load_addr} ${fit_image} && " \ + "load mmc 0 ${load_addr} ${fit_image} && " \ "bootm ${load_addr}\0" \ "jtagboot=echo TFTPing FIT to RAM... && " \ "tftpboot ${load_addr} ${fit_image} && " \ "bootm ${load_addr}\0" \ "usbboot=if usb start; then " \ "echo Copying FIT from USB to RAM... && " \ - "fatload usb 0 ${load_addr} ${fit_image} && " \ + "load usb 0 ${load_addr} ${fit_image} && " \ "bootm ${load_addr}\0" \ - "fi\0" + "fi\0" \ + DFU_ALT_INFO #define CONFIG_BOOTCOMMAND "run $modeboot" #define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */ @@ -181,6 +237,7 @@ #define CONFIG_CMDLINE_EDITING #define CONFIG_AUTO_COMPLETE #define CONFIG_BOARD_LATE_INIT +#define CONFIG_DISPLAY_BOARDINFO #define CONFIG_SYS_LONGHELP #define CONFIG_CLOCKS #define CONFIG_CMD_CLK @@ -198,7 +255,7 @@ #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x1000) -#define CONFIG_SYS_MALLOC_LEN 0x400000 +#define CONFIG_SYS_MALLOC_LEN 0xC00000 #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE #define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_MALLOC_LEN #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ @@ -219,17 +276,11 @@ #define CONFIG_OF_LIBFDT /* FIT support */ -#define CONFIG_FIT -#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */ #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */ /* FDT support */ #define CONFIG_DISPLAY_BOARDINFO_LATE -/* RSA support */ -#define CONFIG_FIT_SIGNATURE -#define CONFIG_RSA - /* Extend size of kernel image for uncompression */ #define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024) |
