diff options
Diffstat (limited to 'include/configs')
-rw-r--r-- | include/configs/apx4devkit.h | 120 | ||||
-rw-r--r-- | include/configs/m28evk.h | 192 | ||||
-rw-r--r-- | include/configs/mx23_olinuxino.h | 142 | ||||
-rw-r--r-- | include/configs/mx23evk.h | 115 | ||||
-rw-r--r-- | include/configs/mx28evk.h | 173 | ||||
-rw-r--r-- | include/configs/mx6qsabrelite.h | 284 | ||||
-rw-r--r-- | include/configs/mx6sabre_common.h | 3 | ||||
-rw-r--r-- | include/configs/mx6sabresd.h | 19 | ||||
-rw-r--r-- | include/configs/mxs.h | 191 | ||||
-rw-r--r-- | include/configs/nitrogen6x.h | 81 | ||||
-rw-r--r-- | include/configs/sc_sps_1.h | 139 | ||||
-rw-r--r-- | include/configs/wandboard.h | 2 |
12 files changed, 443 insertions, 1018 deletions
diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h index 8561a248c4..d1f18bc45c 100644 --- a/include/configs/apx4devkit.h +++ b/include/configs/apx4devkit.h @@ -11,34 +11,16 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __CONFIG_H -#define __CONFIG_H +#ifndef __CONFIGS_APX4DEVKIT_H__ +#define __CONFIGS_APX4DEVKIT_H__ -/* SoC configurations */ +/* System configurations */ #define CONFIG_MX28 /* i.MX28 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define MACH_TYPE_APX4DEVKIT 3712 #define CONFIG_MACH_TYPE MACH_TYPE_APX4DEVKIT -#include <asm/arch/regs-base.h> - -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_ARCH_MISC_INIT - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - /* U-Boot Commands */ +#define CONFIG_SYS_NO_FLASH #include <config_cmd_default.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -58,78 +40,26 @@ #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_USB -/* Memory configurations */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +/* Environment */ #define CONFIG_ENV_OVERWRITE - -/* U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-Boot version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc. */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_OF_LIBFDT #define CONFIG_ENV_IS_IN_NAND -/* Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* DMA */ -#define CONFIG_APBH_DMA - -/* MMC Driver */ -#ifdef CONFIG_ENV_IS_IN_MMC +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_ENV_OFFSET (256 * 1024) #define CONFIG_ENV_SIZE (16 * 1024) #define CONFIG_SYS_MMC_ENV_DEV 0 #endif -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_MXS_MMC -#endif - -/* NAND Driver */ -#ifdef CONFIG_ENV_IS_IN_NAND +/* Environment is in NAND */ +#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_SIZE (128 * 1024) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE @@ -139,12 +69,8 @@ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) #endif +/* UBI and NAND partitioning */ #ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_MXS -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_SYS_NAND_5_ADDR_CYCLE - #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_CMD_MTDPARTS @@ -159,43 +85,30 @@ #define MTDPARTS_DEFAULT "" #endif -/* Ethernet on SOC (FEC) */ +/* FEC Ethernet on SoC */ #ifdef CONFIG_CMD_NET +#define CONFIG_FEC_MXC #define CONFIG_NET_MULTI #define CONFIG_ETHPRIME "FEC" -#define CONFIG_FEC_MXC #define CONFIG_FEC_MXC_PHYADDR 0 #define IMX_FEC_BASE MXS_ENET0_BASE -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII #endif /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT1 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MXS -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#endif /* RTC */ -#if defined(CONFIG_CMD_DATE) +#ifdef CONFIG_CMD_DATE #define CONFIG_RTC_PCF8563 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 #endif /* Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTCOMMAND "run bootcmd_nand" @@ -225,4 +138,7 @@ "ext2load mmc 0:2 41000000 boot/uImage && bootm 41000000\0" \ "" -#endif /* __CONFIG_H */ +/* The rest of the configuration is shared */ +#include <configs/mxs.h> + +#endif /* __CONFIGS_APX4DEVKIT_H__ */ diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index fd3ae028dc..eba875954d 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -4,43 +4,17 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __M28EVK_CONFIG_H__ -#define __M28EVK_CONFIG_H__ +#ifndef __CONFIGS_M28EVK_H__ +#define __CONFIGS_M28EVK_H__ -/* - * SoC configurations - */ -#define CONFIG_MX28 /* i.MX28 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ -/* - * Define M28EVK machine type by hand until it lands in mach-types - */ +/* System configurations */ +#define CONFIG_MX28 /* i.MX28 SoC */ #define MACH_TYPE_M28EVK 3613 - #define CONFIG_MACH_TYPE MACH_TYPE_M28EVK -#include <asm/arch/regs-base.h> - +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* - * SPL - */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - -/* - * U-Boot Commands - */ #include <config_cmd_default.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -69,86 +43,18 @@ #define CONFIG_REGEX /* Enable regular expression support */ -/* - * Memory configurations - */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 - -/* - * U-Boot general configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Serial Driver - */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ - -/* - * MMC Driver - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_GENERIC_MMC -#define CONFIG_MXS_MMC -#endif -/* - * APBH DMA - */ -#define CONFIG_APBH_DMA - -/* - * NAND - */ +/* Environment */ #define CONFIG_ENV_SIZE (16 * 1024) -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_MXS -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_ENV_IS_IN_NAND /* Environment is in NAND */ -#define CONFIG_ENV_IS_IN_NAND +#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_RANGE (512 * 1024) @@ -177,40 +83,22 @@ #define CONFIG_ENV_IS_NOWHERE #endif -/* - * Ethernet on SOC (FEC) - */ -#ifdef CONFIG_CMD_NET -#define CONFIG_ETHPRIME "FEC0" +/* FEC Ethernet on SoC */ +#ifdef CONFIG_CMD_NET #define CONFIG_FEC_MXC -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII #endif -/* - * I2C - */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MXS -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#endif - -/* - * EEPROM - */ -#ifdef CONFIG_CMD_EEPROM +/* EEPROM */ +#ifdef CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #endif -/* - * RTC - */ -#ifdef CONFIG_CMD_DATE +/* RTC */ +#ifdef CONFIG_CMD_DATE /* Use the internal RTC in the MXS chip */ #define CONFIG_RTC_INTERNAL -#ifdef CONFIG_RTC_INTERNAL +#ifdef CONFIG_RTC_INTERNAL #define CONFIG_RTC_MXS #else #define CONFIG_RTC_M41T62 @@ -219,32 +107,22 @@ #endif #endif -/* - * USB - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS +/* USB */ +#ifdef CONFIG_CMD_USB #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_EHCI_MXS_PORT1 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif -/* - * SPI - */ -#ifdef CONFIG_CMD_SPI -#define CONFIG_HARD_SPI -#define CONFIG_MXS_SPI -#define CONFIG_SPI_HALF_DUPLEX +/* SPI */ +#ifdef CONFIG_CMD_SPI #define CONFIG_DEFAULT_SPI_BUS 2 #define CONFIG_DEFAULT_SPI_CS 0 #define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0 /* SPI FLASH */ -#ifdef CONFIG_CMD_SF +#ifdef CONFIG_CMD_SF #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_STMICRO #define CONFIG_SF_DEFAULT_BUS 2 @@ -257,18 +135,12 @@ #define CONFIG_ENV_SPI_MAX_HZ 40000000 #define CONFIG_ENV_SPI_MODE SPI_MODE_0 #endif + #endif -/* - * LCD - */ -#ifdef CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_MXS +/* LCD */ +#ifdef CONFIG_VIDEO #define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP @@ -277,22 +149,15 @@ #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10) #endif -/* - * Boot Linux - */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS +/* Booting Linux */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 " #define CONFIG_BOOTCOMMAND "run bootcmd_net" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT -/* - * Extra Environments - */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_nand_full_filename=u-boot.nand\0" \ "update_nand_firmware_filename=u-boot.sb\0" \ @@ -333,4 +198,7 @@ "fi ; " \ "fi\0" -#endif /* __M28EVK_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include <configs/mxs.h> + +#endif /* __CONFIGS_M28EVK_H__ */ diff --git a/include/configs/mx23_olinuxino.h b/include/configs/mx23_olinuxino.h index 94bedd6d25..575fe2a22d 100644 --- a/include/configs/mx23_olinuxino.h +++ b/include/configs/mx23_olinuxino.h @@ -3,40 +3,15 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __MX23_OLINUXINO_CONFIG_H__ -#define __MX23_OLINUXINO_CONFIG_H__ +#ifndef __CONFIGS_MX23_OLINUXINO_H__ +#define __CONFIGS_MX23_OLINUXINO_H__ -#include <asm/arch/iomux-mx23.h> - -/* - * SoC configurations - */ +/* System configurations */ #define CONFIG_MX23 /* i.MX23 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define CONFIG_MACH_TYPE 4105 -#include <asm/arch/regs-base.h> - +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* - * SPL - */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - -/* - * U-Boot Commands - */ #include <config_cmd_default.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -51,92 +26,36 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_USB -/* - * Memory configurations - */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 -/* - * U-Boot general configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER +/* Environment */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OVERWRITE -/* - * Serial Driver - */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_ENV_SIZE (16 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 +#endif -/* - * Status LED - */ +/* Status LED */ #define CONFIG_STATUS_LED #define CONFIG_GPIO_LED #define CONFIG_BOARD_SPECIFIC_LED -#define STATUS_LED_BOOT 0 -#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 #define STATUS_LED_STATE STATUS_LED_ON #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -/* - * MMC Driver - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_GENERIC_MMC -#define CONFIG_MXS_MMC -#endif - -/* - * APBH DMA - */ -#define CONFIG_APBH_DMA - /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif @@ -146,31 +65,13 @@ #define CONFIG_USB_ETHER_SMSC95XX #endif -/* - * Boot Linux - */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS +/* Booting Linux */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OVERWRITE -#ifdef CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET (256 * 1024) -#define CONFIG_ENV_SIZE (16 * 1024) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -/* - * Extra Environments - */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_sd_firmware_filename=u-boot.sd\0" \ "update_sd_firmware=" /* Update the SD firmware partition */ \ @@ -252,4 +153,7 @@ "fi; " \ "else run netboot; fi" -#endif /* __MX23_OLINUXINO_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include <configs/mxs.h> + +#endif /* __CONFIGS_MX23_OLINUXINO_H__ */ diff --git a/include/configs/mx23evk.h b/include/configs/mx23evk.h index 2380649e06..1b40a36fcf 100644 --- a/include/configs/mx23evk.h +++ b/include/configs/mx23evk.h @@ -6,33 +6,15 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __MX23EVK_CONFIG_H__ -#define __MX23EVK_CONFIG_H__ +#ifndef __CONFIGS_MX23EVK_H__ +#define __CONFIGS_MX23EVK_H__ -/* SoC configurations */ +/* System configurations */ #define CONFIG_MX23 /* i.MX23 SoC */ - -#include <asm/arch/regs-base.h> - -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define CONFIG_MACH_TYPE MACH_TYPE_MX23EVK -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - /* U-Boot Commands */ +#define CONFIG_SYS_NO_FLASH #include <config_cmd_default.h> #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS @@ -49,86 +31,33 @@ #define CONFIG_CMD_BOOTZ #define CONFIG_VIDEO -/* Memory configurations */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ -#define CONFIG_STACKSIZE (128 * 1024) /* 128 KB stack */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +/* Environment */ #define CONFIG_ENV_OVERWRITE +#define CONFIG_ENV_IS_IN_MMC -/* U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -/* Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ - -/* DMA */ -#define CONFIG_APBH_DMA - -/* MMC Driver */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_MXS_MMC +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_ENV_SIZE (16 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif /* Framebuffer support */ #ifdef CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_MXS #define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP @@ -138,21 +67,10 @@ #endif /* Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_LOADADDR 0x42000000 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT - -/* Environment */ -#define CONFIG_ENV_IS_IN_MMC -#ifdef CONFIG_ENV_IS_IN_MMC - #define CONFIG_ENV_OFFSET (256 * 1024) - #define CONFIG_ENV_SIZE (16 * 1024) - #define CONFIG_SYS_MMC_ENV_DEV 0 -#endif /* Extra Environments */ #define CONFIG_EXTRA_ENV_SETTINGS \ @@ -211,4 +129,7 @@ "fi; " \ "else exit; fi" -#endif /* __MX23EVK_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include <configs/mxs.h> + +#endif /* __CONFIGS_MX23EVK_H__ */ diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index 885e513f9d..07f88ca4c7 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -8,33 +8,16 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __MX28EVK_CONFIG_H__ -#define __MX28EVK_CONFIG_H__ +#ifndef __CONFIGS_MX28EVK_H__ +#define __CONFIGS_MX28EVK_H__ -/* SoC configurations */ +/* System configurations */ #define CONFIG_MX28 /* i.MX28 SoC */ - -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK - -#include <asm/arch/regs-base.h> - -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > " /* U-Boot Commands */ +#define CONFIG_SYS_NO_FLASH #include <config_cmd_default.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -49,6 +32,7 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_NFS #define CONFIG_CMD_PING +#define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SETEXPR #define CONFIG_CMD_SF #define CONFIG_CMD_SPI @@ -58,81 +42,24 @@ #define CONFIG_CMD_NAND_TRIMFFS #define CONFIG_VIDEO -/* Memory configurations */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +/* Environment */ +#define CONFIG_ENV_SIZE (16 * 1024) #define CONFIG_ENV_OVERWRITE -/* U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER - -/* Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ -/* DMA */ -#define CONFIG_APBH_DMA - -/* MMC Driver */ -#ifdef CONFIG_ENV_IS_IN_MMC - #define CONFIG_ENV_OFFSET (256 * 1024) - #define CONFIG_ENV_SIZE (16 * 1024) - #define CONFIG_SYS_MMC_ENV_DEV 0 -#endif -#define CONFIG_CMD_SAVEENV -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_MXS_MMC +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif -/* NAND Driver */ -#define CONFIG_ENV_SIZE (16 * 1024) -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_MXS -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_SYS_NAND_5_ADDR_CYCLE - /* Environment is in NAND */ -#ifdef CONFIG_ENV_IS_IN_NAND +#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_RANGE (512 * 1024) @@ -141,6 +68,21 @@ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) #endif +/* Environemnt is in SPI flash */ +#if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_SIZE 0x1000 /* 4KB */ +#define CONFIG_ENV_OFFSET 0x40000 /* 256K */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SECT_SIZE 0x1000 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_BUS 2 +#define CONFIG_ENV_SPI_MAX_HZ 24000000 +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#endif + +/* UBI and NAND partitioning */ +#ifdef CONFIG_CMD_NAND #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_CMD_MTDPARTS @@ -160,13 +102,10 @@ "-(filesystem)" #endif -/* Ethernet on SOC (FEC) */ +/* FEC Ethernet on SoC */ #ifdef CONFIG_CMD_NET -#define CONFIG_NET_MULTI -#define CONFIG_ETHPRIME "FEC0" #define CONFIG_FEC_MXC -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII +#define CONFIG_NET_MULTI #define CONFIG_MX28_FEC_MAC_IN_OCOTP #endif @@ -177,65 +116,35 @@ /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT1 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_ETHER_SMSC95XX #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MXS -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#endif - /* SPI */ #ifdef CONFIG_CMD_SPI -#define CONFIG_HARD_SPI -#define CONFIG_MXS_SPI -#define CONFIG_SPI_HALF_DUPLEX #define CONFIG_DEFAULT_SPI_BUS 2 #define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0 /* SPI Flash */ #ifdef CONFIG_CMD_SF #define CONFIG_SPI_FLASH -#define CONFIG_SF_DEFAULT_BUS 2 -#define CONFIG_SF_DEFAULT_CS 0 +#define CONFIG_SF_DEFAULT_BUS 2 +#define CONFIG_SF_DEFAULT_CS 0 /* this may vary and depends on the installed chip */ #define CONFIG_SPI_FLASH_SST #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #define CONFIG_SF_DEFAULT_SPEED 24000000 - -/* (redundant) environemnt in SPI flash */ -#ifdef CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_SYS_REDUNDAND_ENVIRONMENT -#define CONFIG_ENV_SIZE 0x1000 /* 4KB */ -#define CONFIG_ENV_OFFSET 0x40000 /* 256K */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#define CONFIG_ENV_SECT_SIZE 0x1000 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_BUS 2 -#define CONFIG_ENV_SPI_MAX_HZ 24000000 -#define CONFIG_ENV_SPI_MODE SPI_MODE_0 -#endif #endif + #endif /* Framebuffer support */ #ifdef CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_MXS #define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP @@ -245,15 +154,12 @@ #endif /* Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_LOADADDR 0x42000000 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT -/* Extra Environments */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_nand_full_filename=u-boot.nand\0" \ "update_nand_firmware_filename=u-boot.sb\0" \ @@ -364,4 +270,7 @@ "fi; " \ "else run netboot; fi" -#endif /* __MX28EVK_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include <configs/mxs.h> + +#endif /* __CONFIGS_MX28EVK_H__ */ diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h deleted file mode 100644 index 511db73605..0000000000 --- a/include/configs/mx6qsabrelite.h +++ /dev/null @@ -1,284 +0,0 @@ -/* - * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. - * - * Configuration settings for the Freescale i.MX6Q Sabre Lite board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MX6 -#define CONFIG_MX6Q - -#include "mx6_common.h" - -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO - -#define CONFIG_MACH_TYPE 3769 - -#include <asm/arch/imx-regs.h> -#include <asm/imx-common/gpio.h> - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) - -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_MISC_INIT_R -#define CONFIG_MXC_GPIO - -#define CONFIG_CMD_FUSE -#ifdef CONFIG_CMD_FUSE -#define CONFIG_MXC_OCOTP -#endif - -#define CONFIG_MXC_UART -#define CONFIG_MXC_UART_BASE UART2_BASE - -#define CONFIG_CMD_SF -#ifdef CONFIG_CMD_SF -#define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_SST -#define CONFIG_MXC_SPI -#define CONFIG_SF_DEFAULT_BUS 0 -#define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(3, 19)<<8)) -#define CONFIG_SF_DEFAULT_SPEED 25000000 -#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) -#endif - -/* I2C Configs */ -#define CONFIG_CMD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_MXC -#define CONFIG_SYS_I2C_SPEED 100000 - -/* MMC Configs */ -#define CONFIG_FSL_ESDHC -#define CONFIG_FSL_USDHC -#define CONFIG_SYS_FSL_ESDHC_ADDR 0 -#define CONFIG_SYS_FSL_USDHC_NUM 2 - -#define CONFIG_MMC -#define CONFIG_CMD_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMD_SATA -/* - * SATA Configs - */ -#ifdef CONFIG_CMD_SATA -#define CONFIG_DWC_AHSATA -#define CONFIG_SYS_SATA_MAX_DEVICE 1 -#define CONFIG_DWC_AHSATA_PORT_ID 0 -#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR -#define CONFIG_LBA48 -#define CONFIG_LIBATA -#endif - -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_FEC_MXC -#define CONFIG_MII -#define IMX_FEC_BASE ENET_BASE_ADDR -#define CONFIG_FEC_XCV_TYPE RGMII -#define CONFIG_ETHPRIME "FEC" -#define CONFIG_FEC_MXC_PHYADDR 6 -#define CONFIG_PHYLIB -#define CONFIG_PHY_MICREL -#define CONFIG_PHY_MICREL_KSZ9021 - -/* USB Configs */ -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 -#define CONFIG_USB_STORAGE -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_ASIX -#define CONFIG_USB_ETHER_SMSC95XX -#define CONFIG_MXC_USB_PORT 1 -#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) -#define CONFIG_MXC_USB_FLAGS 0 - -/* Miscellaneous commands */ -#define CONFIG_CMD_BMODE - -/* Framebuffer and LCD */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_IPUV3 -#define CONFIG_CFB_CONSOLE -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE -#define CONFIG_VIDEO_BMP_RLE8 -#define CONFIG_SPLASH_SCREEN -#define CONFIG_BMP_16BPP -#define CONFIG_VIDEO_LOGO -#define CONFIG_IPUV3_CLK 260000000 - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* Command definition */ -#include <config_cmd_default.h> - -#undef CONFIG_CMD_IMLS - -#define CONFIG_BOOTDELAY 1 - -#define CONFIG_PREBOOT "" - -#define CONFIG_LOADADDR 0x12000000 -#define CONFIG_SYS_TEXT_BASE 0x17800000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "script=boot.scr\0" \ - "uimage=uImage\0" \ - "console=ttymxc1\0" \ - "fdt_high=0xffffffff\0" \ - "initrd_high=0xffffffff\0" \ - "fdt_file=imx6q-sabrelite.dtb\0" \ - "fdt_addr=0x11000000\0" \ - "boot_fdt=try\0" \ - "ip_dyn=yes\0" \ - "mmcdev=0\0" \ - "mmcpart=1\0" \ - "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ - "mmcargs=setenv bootargs console=${console},${baudrate} " \ - "root=${mmcroot}\0" \ - "loadbootscript=" \ - "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ - "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootm; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootm; " \ - "fi;\0" \ - "netargs=setenv bootargs console=${console},${baudrate} " \ - "root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ - "netboot=echo Booting from net ...; " \ - "run netargs; " \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "${get_cmd} ${uimage}; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootm; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootm; " \ - "fi;\0" - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run netboot; " \ - "fi; " \ - "fi; " \ - "else run netboot; fi" - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT "MX6QSABRELITE U-Boot > " -#define CONFIG_AUTO_COMPLETE -#define CONFIG_SYS_CBSIZE 256 - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x10000000 -#define CONFIG_SYS_MEMTEST_END 0x10010000 -#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_HZ 1000 - -#define CONFIG_CMDLINE_EDITING - -/* Physical Memory Map */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR -#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM -#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR -#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* FLASH and environment organization */ -#define CONFIG_SYS_NO_FLASH - -#define CONFIG_ENV_SIZE (8 * 1024) - -#define CONFIG_ENV_IS_IN_MMC -/* #define CONFIG_ENV_IS_IN_SPI_FLASH */ - -#if defined(CONFIG_ENV_IS_IN_MMC) -#define CONFIG_ENV_OFFSET (6 * 64 * 1024) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH) -#define CONFIG_ENV_OFFSET (768 * 1024) -#define CONFIG_ENV_SECT_SIZE (8 * 1024) -#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS -#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS -#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE -#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED -#endif - -#define CONFIG_OF_LIBFDT -#define CONFIG_CMD_BOOTZ - -#ifndef CONFIG_SYS_DCACHE_OFF -#define CONFIG_CMD_CACHE -#endif - -#endif /* __CONFIG_H */ diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h index dad8618c0a..bf6113b2aa 100644 --- a/include/configs/mx6sabre_common.h +++ b/include/configs/mx6sabre_common.h @@ -12,6 +12,7 @@ #define CONFIG_MX6 #include "mx6_common.h" +#include <asm/sizes.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO @@ -24,7 +25,7 @@ #define CONFIG_REVISION_TAG /* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_LATE_INIT diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h index 57e1860b1b..a3dd74a4a2 100644 --- a/include/configs/mx6sabresd.h +++ b/include/configs/mx6sabresd.h @@ -9,6 +9,9 @@ #ifndef __MX6QSABRESD_CONFIG_H #define __MX6QSABRESD_CONFIG_H +#include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> + #define CONFIG_MACH_TYPE 3980 #define CONFIG_MXC_UART_BASE UART1_BASE #define CONFIG_CONSOLE_DEV "ttymxc0" @@ -23,4 +26,20 @@ #define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC3 */ #endif +/* Framebuffer */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_IPUV3 +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_IMX_HDMI + #endif /* __MX6QSABRESD_CONFIG_H */ diff --git a/include/configs/mxs.h b/include/configs/mxs.h new file mode 100644 index 0000000000..a684166502 --- /dev/null +++ b/include/configs/mxs.h @@ -0,0 +1,191 @@ +/* + * Copyright (C) 2013 Marek Vasut <marex@denx.de> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __CONFIGS_MXS_H__ +#define __CONFIGS_MXS_H__ + +/* + * Includes + */ + +#if defined(CONFIG_MX23) && defined(CONFIG_MX28) +#error Select either CONFIG_MX23 or CONFIG_MX28 , never both! +#elif !defined(CONFIG_MX23) && !defined(CONFIG_MX28) +#error Select one of CONFIG_MX23 or CONFIG_MX28 ! +#endif + +#include <asm/arch/regs-base.h> + +#if defined(CONFIG_MX23) +#include <asm/arch/iomux-mx23.h> +#elif defined(CONFIG_MX28) +#include <asm/arch/iomux-mx28.h> +#endif + +/* + * CPU specifics + */ + +/* Ticks per second */ +#define CONFIG_SYS_HZ 1000 + +/* MXS uses FDT */ +#define CONFIG_OF_LIBFDT + +/* Startup hooks */ +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_ARCH_MISC_INIT + +/* SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_NO_CPU_SUPPORT_CODE +#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT + +/* Memory sizes */ +#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ +#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ +#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ + +/* OCRAM at 0x0 ; 32kB on MX23 ; 128kB on MX28 */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 +#if defined(CONFIG_MX23) +#define CONFIG_SYS_INIT_RAM_SIZE (32 * 1024) +#elif defined(CONFIG_MX28) +#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) +#endif + +/* Point initial SP in SRAM so SPL can use it too. */ +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* + * We need to sacrifice first 4 bytes of RAM here to avoid triggering some + * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot + * binary. In case there was more of this mess, 0x100 bytes are skipped. + */ +#define CONFIG_SYS_TEXT_BASE 0x40000100 + +/* U-Boot general configuration */ +#define CONFIG_SYS_LONGHELP +#ifndef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "=> " +#endif +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print buffer size */ +#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot argument buffer size */ +#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ +#define CONFIG_AUTO_COMPLETE /* Command auto complete */ +#define CONFIG_CMDLINE_EDITING /* Command history etc */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* Booting Linux */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS + +/* + * Drivers + */ + +/* APBH DMA */ +#define CONFIG_APBH_DMA + +/* GPIO */ +#define CONFIG_MXS_GPIO + +/* DUART Serial Driver */ +#define CONFIG_PL011_SERIAL +#define CONFIG_PL011_CLOCK 24000000 +#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } +#define CONFIG_CONS_INDEX 0 +/* Default baudrate can be overriden by board! */ +#ifndef CONFIG_BAUDRATE +#define CONFIG_BAUDRATE 115200 +#endif + +/* FEC Ethernet on SoC */ +#ifdef CONFIG_FEC_MXC +#define CONFIG_MII +#ifndef CONFIG_ETHPRIME +#define CONFIG_ETHPRIME "FEC0" +#endif +#ifndef CONFIG_FEC_XCV_TYPE +#define CONFIG_FEC_XCV_TYPE RMII +#endif +#endif + +/* I2C */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_I2C_MXS +#define CONFIG_HARD_I2C +#ifndef CONFIG_SYS_I2C_SPEED +#define CONFIG_SYS_I2C_SPEED 400000 +#endif +#endif + +/* LCD */ +#ifdef CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_MXS +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#endif + +/* MMC */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_MXS_MMC +#endif + +/* NAND */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_MXS +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x60000000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#endif + +/* SPI */ +#ifdef CONFIG_CMD_SPI +#define CONFIG_HARD_SPI +#define CONFIG_MXS_SPI +#define CONFIG_SPI_HALF_DUPLEX +#endif + +/* USB */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MXS +#define CONFIG_EHCI_IS_TDI +#endif + +#endif /* __CONFIGS_MXS_H__ */ diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index 4242414266..3454b862a8 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -141,6 +141,7 @@ #define CONFIG_IPUV3_CLK 260000000 #define CONFIG_CMD_HDMIDETECT #define CONFIG_CONSOLE_MUX +#define CONFIG_IMX_HDMI /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE @@ -173,6 +174,80 @@ #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC +#if defined(CONFIG_SABRELITE) +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console=ttymxc1\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6q-sabrelite.dtb\0" \ + "fdt_addr=0x11000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=1\0" \ + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${uimage}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" +#else #define CONFIG_EXTRA_ENV_SETTINGS \ "console=ttymxc1\0" \ "clearenv=if sf probe || sf probe || sf probe 1 ; then " \ @@ -206,6 +281,7 @@ "done ; " \ "done\0" \ +#endif /* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP #define CONFIG_SYS_HUSH_PARSER @@ -245,8 +321,11 @@ #define CONFIG_ENV_SIZE (8 * 1024) -/* #define CONFIG_ENV_IS_IN_MMC */ +#if defined(CONFIG_SABRELITE) +#define CONFIG_ENV_IS_IN_MMC +#else #define CONFIG_ENV_IS_IN_SPI_FLASH +#endif #if defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_ENV_OFFSET (6 * 64 * 1024) diff --git a/include/configs/sc_sps_1.h b/include/configs/sc_sps_1.h index 9c2eb05c04..58ffa36dd9 100644 --- a/include/configs/sc_sps_1.h +++ b/include/configs/sc_sps_1.h @@ -6,48 +6,16 @@ * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __SC_SPS_1_H__ -#define __SC_SPS_1_H__ +#ifndef __CONFIGS_SC_SPS_1_H__ +#define __CONFIGS_SC_SPS_1_H__ -/* - * SoC configurations - */ +/* System configuration */ #define CONFIG_MX28 /* i.MX28 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - -/* - * Define SC_SPS_1 machine type by hand until it lands in mach-types - */ #define MACH_TYPE_SC_SPS_1 4172 - #define CONFIG_MACH_TYPE MACH_TYPE_SC_SPS_1 -#include <asm/arch/regs-base.h> - +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_ARCH_MISC_INIT - -#define CONFIG_ENV_IS_IN_MMC - -#define CONFIG_OF_LIBFDT - -/* - * SPL - */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - -/* - * U-Boot Commands - */ #include <config_cmd_default.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -65,119 +33,47 @@ #define CONFIG_CMD_SETEXPR #define CONFIG_CMD_USB -/* - * Memory configurations - */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */ -#define CONFIG_STACKSIZE 0x00010000 /* 128 KB stack */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 - -/* - * U-Boot general configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -/* - * Serial Driver - */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * MMC Driver - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_APBH_DMA -#define CONFIG_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_GENERIC_MMC -#define CONFIG_MXS_MMC -#endif +/* Environment */ #define CONFIG_ENV_SIZE (16 * 1024) -#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_IS_IN_MMC + +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_ENV_OFFSET (256 * 1024) #define CONFIG_SYS_MMC_ENV_DEV 0 #else #define CONFIG_ENV_IS_NOWHERE #endif -/* - * Ethernet on SOC (FEC) - */ +/* FEC Ethernet on SoC */ #ifdef CONFIG_CMD_NET -#define CONFIG_ETHPRIME "FEC0" #define CONFIG_FEC_MXC -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII #define CONFIG_PHYLIB #define CONFIG_PHY_SMSC #endif -/* - * USB - */ +/* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif -/* - * Boot Linux - */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS +/* Booting Linux */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTARGS "console=ttyAMA0,115200" -#define CONFIG_BOOTCOMMAND "bootm " +#define CONFIG_BOOTCOMMAND "bootm" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* - * Extra Environments - */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_sd_firmware_filename=u-boot.sd\0" \ "update_sd_firmware=" /* Update the SD firmware partition */ \ @@ -189,4 +85,7 @@ "fi ; " \ "fi\0" -#endif /* __SC_SPS_1_H__ */ +/* The rest of the configuration is shared */ +#include <configs/mxs.h> + +#endif /* __CONFIGS_SC_SPS_1_H__ */ diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h index 9c23b26200..665cfc3cfa 100644 --- a/include/configs/wandboard.h +++ b/include/configs/wandboard.h @@ -97,6 +97,7 @@ #define CONFIG_VIDEO_LOGO #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_IMX_HDMI #if defined(CONFIG_MX6DL) #define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb" @@ -110,6 +111,7 @@ "script=boot.scr\0" \ "uimage=uImage\0" \ "console=ttymxc0\0" \ + "splashpos=m,m\0" \ "fdt_high=0xffffffff\0" \ "initrd_high=0xffffffff\0" \ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ |