diff options
Diffstat (limited to 'include/configs/socfpga_common.h')
| -rw-r--r-- | include/configs/socfpga_common.h | 76 |
1 files changed, 75 insertions, 1 deletions
diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h index 83a1bcdfbe..c436fdaf52 100644 --- a/include/configs/socfpga_common.h +++ b/include/configs/socfpga_common.h @@ -37,7 +37,7 @@ */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM_1 0x0 -#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) +#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024) #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 #define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE @@ -79,6 +79,25 @@ #define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS /* + * EPCS/EPCQx1 Serial Flash Controller + */ +#ifdef CONFIG_ALTERA_SPI +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SPI_FLASH_BAR +/* + * The base address is configurable in QSys, each board must specify the + * base address based on it's particular FPGA configuration. Please note + * that the address here is incremented by 0x400 from the Base address + * selected in QSys, since the SPI registers are at offset +0x400. + * #define CONFIG_SYS_SPI_BASE 0xff240400 + */ +#endif + +/* * Ethernet on SoC (EMAC) */ #if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET) @@ -141,6 +160,33 @@ #define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */ #endif + /* + * I2C support + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_DW +#define CONFIG_SYS_I2C_BUS_MAX 4 +#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS +#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS +#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS +#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS +/* Using standard mode which the speed up to 100Kb/s */ +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SPEED1 100000 +#define CONFIG_SYS_I2C_SPEED2 100000 +#define CONFIG_SYS_I2C_SPEED3 100000 +/* Address of device when used as slave */ +#define CONFIG_SYS_I2C_SLAVE 0x02 +#define CONFIG_SYS_I2C_SLAVE1 0x02 +#define CONFIG_SYS_I2C_SLAVE2 0x02 +#define CONFIG_SYS_I2C_SLAVE3 0x02 +#ifndef __ASSEMBLY__ +/* Clock supplied to I2C controller in unit of MHz */ +unsigned int cm_get_l4_sp_clk_hz(void); +#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000) +#endif +#define CONFIG_CMD_I2C + /* * Serial Driver */ @@ -172,6 +218,34 @@ #endif /* + * USB Gadget (DFU, UMS) + */ +#if defined(CONFIG_CMD_DFU) || defined(CONFIG_CMD_USB_MASS_STORAGE) +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_S3C_UDC_OTG +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_VBUS_DRAW 2 + +/* USB Composite download gadget - g_dnl */ +#define CONFIG_USBDOWNLOAD_GADGET +#define CONFIG_USB_GADGET_MASS_STORAGE + +#define CONFIG_DFU_FUNCTION +#define CONFIG_DFU_MMC +#define CONFIG_SYS_DFU_DATA_BUF_SIZE (32 * 1024 * 1024) +#define DFU_DEFAULT_POLL_TIMEOUT 300 + +/* USB IDs */ +#define CONFIG_G_DNL_VENDOR_NUM 0x0525 /* NetChip */ +#define CONFIG_G_DNL_PRODUCT_NUM 0xA4A5 /* Linux-USB File-backed Storage Gadget */ +#define CONFIG_G_DNL_UMS_VENDOR_NUM CONFIG_G_DNL_VENDOR_NUM +#define CONFIG_G_DNL_UMS_PRODUCT_NUM CONFIG_G_DNL_PRODUCT_NUM +#ifndef CONFIG_G_DNL_MANUFACTURER +#define CONFIG_G_DNL_MANUFACTURER "Altera" +#endif +#endif + +/* * U-Boot environment */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
