diff options
Diffstat (limited to 'include/configs/rsdproto.h')
| -rw-r--r-- | include/configs/rsdproto.h | 400 |
1 files changed, 0 insertions, 400 deletions
diff --git a/include/configs/rsdproto.h b/include/configs/rsdproto.h deleted file mode 100644 index 06211380d4..0000000000 --- a/include/configs/rsdproto.h +++ /dev/null @@ -1,400 +0,0 @@ -/* - * (C) Copyright 2000 - * Murray Jensen <Murray.Jensen@cmst.csiro.au> - * - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * Configuation settings for the R&S Protocol Board board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_RSD_PROTO 1 /* on a R&S Protocol Board */ -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_SYS_TEXT_BASE 0xff000000 -#define CONFIG_SYS_LDSCRIPT "board/rsdproto/u-boot.lds" - -#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere. - */ -#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on neither */ -#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ -#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ -#define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ - -#if (CONFIG_ETHER_INDEX == 2) - -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Enable Full Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) -# define CONFIG_SYS_CPMFCR_RAMTYPE (0) -# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#endif /* CONFIG_ETHER_INDEX */ - - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* enable I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 50000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x30 - - -/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ -#define CONFIG_8260_CLKIN 50000000 /* in Hz */ - -#define CONFIG_BAUDRATE 115200 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#undef CONFIG_CMD_KGDB - - -/* Define this if you want to boot from 0x00000100. If you don't define - * this, you will need to program the bootloader to 0xfff00000, and - * get the hardware reset config words at 0xfe000000. The simplest - * way to do that is to program the bootloader at both addresses. - * It is suggested that you just let U-Boot live at 0x00000000. - */ -#define CONFIG_SYS_RSD_BOOT_LOW 1 - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_BOOTARGS "devfs=mount root=ramfs" -#define CONFIG_ETHADDR 08:00:3e:26:0a:5a -#define CONFIG_NETMASK 255.255.0.0 - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x01c00000 /* 4 ... 28 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define PHYS_SDRAM_60X 0x00000000 /* SDRAM (60x Bus) */ -#define PHYS_SDRAM_60X_SIZE 0x08000000 /* 128 MB */ - -#define PHYS_SDRAM_LOCAL 0x40000000 /* SDRAM (Local Bus) */ -#define PHYS_SDRAM_LOCAL_SIZE 0x04000000 /* 64 MB */ - -#define PHYS_DPRAM_PCI 0xE8000000 /* DPRAM PPC/PCI */ -#define PHYS_DPRAM_PCI_SIZE 0x00020000 /* 128 KB */ - -/*#define PHYS_DPRAM_PCI_SEM 0x04020000 / * DPRAM PPC/PCI Semaphore */ -/*#define PHYS_DPRAM_PCI_SEM_SIZE 0x00000001 / * 1 Byte */ - -#define PHYS_DPRAM_SHARC 0xE8100000 /* DPRAM PPC/Sharc */ -#define PHYS_DPRAM_SHARC_SIZE 0x00040000 /* 256 KB */ - -/*#define PHYS_DPRAM_SHARC_SEM 0x04140000 / * DPRAM PPC/Sharc Semaphore */ -/*#define PHYS_DPRAM_SHARC_SEM_SIZE 0x00000001 / * 1 Byte */ - -#define PHYS_VIRTEX_REGISTER 0xE8300000 /* FPGA implemented register */ -#define PHYS_VIRTEX_REGISTER_SIZE 0x00000100 - -#define PHYS_USB 0x04200000 /* USB Controller (60x Bus) */ -#define PHYS_USB_SIZE 0x00000002 /* 2 Bytes */ - -#define PHYS_IMMR 0xF0000000 /* Internal Memory Mapped Reg. */ - -#define PHYS_FLASH 0xFF000000 /* Flash (60x Bus) */ -#define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ - -#define CONFIG_SYS_IMMR PHYS_IMMR - -/*----------------------------------------------------------------------- - * Reset Address - * - * In order to reset the CPU, U-Boot jumps to a special address which - * causes a machine check exception. The default address for this is - * CONFIG_SYS_MONITOR_BASE - sizeof (ulong), which might not always work, eg. when - * testing the monitor in RAM using a JTAG debugger. - * - * Just set CONFIG_SYS_RESET_ADDRESS to an address that you know is sure to - * cause a bus error on your hardware. - */ -#define CONFIG_SYS_RESET_ADDRESS 0x20000000 - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - */ - -#if defined(CONFIG_SYS_RSD_BOOT_LOW) -# define CONFIG_SYS_RSD_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) -#else -# define CONFIG_SYS_RSD_HRCW_BOOT_FLAGS (0) -#endif /* defined(CONFIG_SYS_RSD_BOOT_LOW) */ - -/* get the HRCW ISB field from CONFIG_SYS_IMMR */ -#define CONFIG_SYS_RSD_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\ - ((CONFIG_SYS_IMMR & 0x01000000) >> 7) |\ - ((CONFIG_SYS_IMMR & 0x00100000) >> 4) ) - -#define CONFIG_SYS_HRCW_MASTER (HRCW_L2CPC10 | \ - HRCW_DPPC11 | \ - CONFIG_SYS_RSD_HRCW_IMMR |\ - HRCW_MMR00 | \ - HRCW_APPC10 | \ - HRCW_CS10PC00 | \ - HRCW_MODCK_H0000 |\ - CONFIG_SYS_RSD_HRCW_BOOT_FLAGS) - -/* no slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependend. - */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_60X -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH -/*#define CONFIG_SYS_MONITOR_BASE 0x200000 */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_RAMBOOT -#endif -#define CONFIG_SYS_MONITOR_LEN (160 << 10) /* Reserve 160 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 63 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 12000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 3000 /* Timeout for Flash Write (in ms) */ - -/* turn off NVRAM env feature */ -#undef CONFIG_NVRAM_ENV - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (PHYS_FLASH + 0x28000) /* Addr of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x8000 /* Total Size of Environment Sector */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|HID0_IFEM|HID0_ABE) -#define CONFIG_SYS_HID0_FINAL (HID0_ICE|HID0_IFEM|HID0_ABE|HID0_EMCP) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMR 0 - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BCR 0x100c0000 - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_SIUMCR (SIUMCR_DPPC11 | SIUMCR_L2CPC10 | SIUMCR_APPC10 | \ - SIUMCR_CS10PC01 | SIUMCR_BCTLC01) - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_PBME | SYPCR_LBME | \ - SYPCR_SWRI | SYPCR_SWP) - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC | TMCNTSC_ALR | TMCNTSC_TCF | TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SCCR 0x00000000 - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - */ - -#define CONFIG_SYS_PSDMR 0x494D2452 -#define CONFIG_SYS_LSDMR 0x49492552 - -/* Flash */ -#define CONFIG_SYS_BR0_PRELIM (PHYS_FLASH | BRx_V) -#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(PHYS_FLASH_SIZE) | \ - ORxG_BCTLD | \ - ORxG_SCY_5_CLK) - -/* DPRAM to the PCI BUS on the protocol board */ -#define CONFIG_SYS_BR1_PRELIM (PHYS_DPRAM_PCI | BRx_V) -#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(PHYS_DPRAM_PCI_SIZE) | \ - ORxG_ACS_DIV4) - -/* 60x Bus SDRAM */ -#define CONFIG_SYS_BR2_PRELIM (PHYS_SDRAM_60X | BRx_MS_SDRAM_P | BRx_V) -#define CONFIG_SYS_OR2_PRELIM (ORxS_SIZE_TO_AM(PHYS_SDRAM_60X_SIZE) | \ - ORxS_BPD_4 | \ - ORxS_ROWST_PBI1_A2 | \ - ORxS_NUMR_13 | \ - ORxS_IBID) - -/* Virtex-FPGA - Register */ -#define CONFIG_SYS_BR3_PRELIM (PHYS_VIRTEX_REGISTER | BRx_V) -#define CONFIG_SYS_OR3_PRELIM (ORxS_SIZE_TO_AM(PHYS_VIRTEX_REGISTER_SIZE) | \ - ORxG_SCY_1_CLK | \ - ORxG_ACS_DIV2 | \ - ORxG_CSNT ) - -/* local bus SDRAM */ -#define CONFIG_SYS_BR4_PRELIM (PHYS_SDRAM_LOCAL | BRx_PS_32 | BRx_MS_SDRAM_L | BRx_V) -#define CONFIG_SYS_OR4_PRELIM (ORxS_SIZE_TO_AM(PHYS_SDRAM_LOCAL_SIZE) | \ - ORxS_BPD_4 | \ - ORxS_ROWST_PBI1_A4 | \ - ORxS_NUMR_13) - -/* DPRAM to the Sharc-Bus on the protocol board */ -#define CONFIG_SYS_BR5_PRELIM (PHYS_DPRAM_SHARC | BRx_V) -#define CONFIG_SYS_OR5_PRELIM (P2SZ_TO_AM(PHYS_DPRAM_SHARC_SIZE) | \ - ORxG_ACS_DIV4) - -#endif /* __CONFIG_H */ |
