diff options
Diffstat (limited to 'include/configs/Sandpoint8240.h')
| -rw-r--r-- | include/configs/Sandpoint8240.h | 398 |
1 files changed, 0 insertions, 398 deletions
diff --git a/include/configs/Sandpoint8240.h b/include/configs/Sandpoint8240.h deleted file mode 100644 index 2c0cb89afa..0000000000 --- a/include/configs/Sandpoint8240.h +++ /dev/null @@ -1,398 +0,0 @@ -/* - * (C) Copyright 2001-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC8240 1 -#define CONFIG_SANDPOINT 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#define CONFIG_SYS_LDSCRIPT "board/sandpoint/u-boot.lds" - -#if 0 -#define USE_DINK32 1 -#else -#undef USE_DINK32 -#endif - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 9600 - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run net_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "net_self=tftp ${kernel_addr} ${bootfile};" \ - "tftp ${ramdisk_addr} ${ramdisk};" \ - "run ramargs addip;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp ${kernel_addr} ${bootfile};" \ - "run nfsargs addip;bootm\0" \ - "rootpath=/opt/eldk/ppc_82xx\0" \ - "bootfile=/tftpboot/SP8240/uImage\0" \ - "ramdisk=/tftpboot/SP8240/uRamdisk\0" \ - "kernel_addr=200000\0" \ - "ramdisk_addr=400000\0" \ - "" -#define CONFIG_BOOTCOMMAND "run flash_self" - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_SNTP - - -#define CONFIG_DRAM_SPEED 100 /* MHz */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#undef CONFIG_PCI_PNP - - -#define CONFIG_EEPRO100 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ - -#define PCI_ENET0_IOADDR 0x80000000 -#define PCI_ENET0_MEMADDR 0x80000000 -#define PCI_ENET1_IOADDR 0x81000000 -#define PCI_ENET1_MEMADDR 0x81000000 - - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 - -#if defined (USE_DINK32) -#define CONFIG_SYS_MONITOR_LEN 0x00030000 -#define CONFIG_SYS_MONITOR_BASE 0x00090000 -#define CONFIG_SYS_RAMBOOT 1 -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#else -#undef CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_MONITOR_LEN 0x00030000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - - -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -#endif - -#define CONFIG_SYS_FLASH_BASE 0xFFF00000 -#if 0 -#define CONFIG_SYS_FLASH_SIZE (512 * 1024) /* sandpoint has tiny eeprom */ -#else -#define CONFIG_SYS_FLASH_SIZE (1024 * 1024) /* Unity has onboard 1MByte flash */ -#endif -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */ - -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */ - -#define CONFIG_SYS_EUMB_ADDR 0xFC000000 - -#define CONFIG_SYS_ISA_MEM 0xFD000000 -#define CONFIG_SYS_ISA_IO 0xFE000000 - -#define CONFIG_SYS_FLASH_RANGE_BASE 0xFF000000 /* flash memory address range */ -#define CONFIG_SYS_FLASH_RANGE_SIZE 0x01000000 -#define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */ -#define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */ - -/* - * select i2c support configuration - * - * Supported configurations are {none, software, hardware} drivers. - * If the software driver is chosen, there are some additional - * configuration items that the driver uses to drive the port pins. - */ -#define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#undef CONFIG_SYS_I2C_SOFT -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_SPEED 400000 - -#ifdef CONFIG_SYS_I2C_SOFT -#error "Soft I2C is not configured properly. Please review!" -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_SOFT_SPEED 50000 -#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE -#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ -#define I2C_ACTIVE (iop->pdir |= 0x00010000) -#define I2C_TRISTATE (iop->pdir &= ~0x00010000) -#define I2C_READ ((iop->pdat & 0x00010000) != 0) -#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ - else iop->pdat &= ~0x00010000 -#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ - else iop->pdat &= ~0x00020000 -#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ -#endif /* CONFIG_SYS_I2C_SOFT */ - - -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* write page size */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */ - - -#define CONFIG_SYS_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM } - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ - - -/* #define CONFIG_WINBOND_83C553 1 / *has a winbond bridge */ -#define CONFIG_SYS_USE_WINBOND_IDE 0 /*use winbond 83c553 internal IDE ctrlr */ -#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR 0x80005800 /*pci-isa bridge config addr */ -#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR 0x80005900 /*ide config addr */ - -#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ - -/* - * NS87308 Configuration - */ -#define CONFIG_NS87308 /* Nat Semi super-io controller on ISA bus */ - -#define CONFIG_SYS_NS87308_BADDR_10 1 - -#define CONFIG_SYS_NS87308_DEVS ( CONFIG_SYS_NS87308_UART1 | \ - CONFIG_SYS_NS87308_UART2 | \ - CONFIG_SYS_NS87308_POWRMAN | \ - CONFIG_SYS_NS87308_RTC_APC ) - -#undef CONFIG_SYS_NS87308_PS2MOD - -#define CONFIG_SYS_NS87308_CS0_BASE 0x0076 -#define CONFIG_SYS_NS87308_CS0_CONF 0x30 -#define CONFIG_SYS_NS87308_CS1_BASE 0x0075 -#define CONFIG_SYS_NS87308_CS1_CONF 0x30 -#define CONFIG_SYS_NS87308_CS2_BASE 0x0074 -#define CONFIG_SYS_NS87308_CS2_CONF 0x30 - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK 1843200 - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE) - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ -#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 1 - -#define CONFIG_SYS_ROMNAL 7 /*rom/flash next access time */ -#define CONFIG_SYS_ROMFAL 11 /*rom/flash access time */ - -#define CONFIG_SYS_REFINT 430 /* no of clock cycles between CBR refresh cycles */ - -/* the following are for SDRAM only*/ -#define CONFIG_SYS_BSTOPRE 121 /* Burst To Precharge, sets open page interval */ -#define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */ -#define CONFIG_SYS_RDLAT 4 /* data latency from read command */ -#define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */ -#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ -#define CONFIG_SYS_ACTORW 3 /* Activate to R/W */ -#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ -#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ -#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */ - -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 - -/* memory bank settings*/ -/* - * only bits 20-29 are actually used from these vales to set the - * start/end address the upper two bits will be 0, and the lower 20 - * bits will be set to 0x00000 for a start address, or 0xfffff for an - * end address - */ -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x3ff00000 -#define CONFIG_SYS_BANK1_END 0x3fffffff -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x3ff00000 -#define CONFIG_SYS_BANK2_END 0x3fffffff -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x3ff00000 -#define CONFIG_SYS_BANK3_END 0x3fffffff -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x00000000 -#define CONFIG_SYS_BANK4_END 0x00000000 -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x00000000 -#define CONFIG_SYS_BANK5_END 0x00000000 -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x00000000 -#define CONFIG_SYS_BANK6_END 0x00000000 -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x00000000 -#define CONFIG_SYS_BANK7_END 0x00000000 -#define CONFIG_SYS_BANK7_ENABLE 0 -/* - * Memory bank enable bitmask, specifying which of the banks defined above - are actually present. MSB is for bank #7, LSB is for bank #0. - */ -#define CONFIG_SYS_BANK_ENABLE 0x01 - -#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */ - /* see 8240 book for bit definitions */ -#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */ - /* currently accessed page in memory */ - /* see 8240 book for details */ - -/* SDRAM 0 - 256MB */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -/* stack in DCACHE @ 1GB (no backing mem) */ -#if defined(USE_DINK32) -#define CONFIG_SYS_IBAT1L (0x40000000 | BATL_PP_00 ) -#define CONFIG_SYS_IBAT1U (0x40000000 | BATU_BL_128K ) -#else -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#endif - -/* PCI memory */ -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -/* Flash, config addrs, etc */ -#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 20 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* values according to the manual */ - -#define CONFIG_DRAM_50MHZ 1 -#define CONFIG_SDRAM_50MHZ - -#undef NR_8259_INTS -#define NR_8259_INTS 1 - - -#define CONFIG_DISK_SPINUP_TIME 1000000 - - -#endif /* __CONFIG_H */ |
