diff options
Diffstat (limited to 'include/configs/MPC8540ADS.h')
| -rw-r--r-- | include/configs/MPC8540ADS.h | 148 |
1 files changed, 74 insertions, 74 deletions
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 951d1fefb0..2f1bb487f8 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -31,21 +31,21 @@ #define __CONFIG_H /* High Level Configuration Options */ -#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */ -#define CONFIG_MPC8540 1 /* MPC8540 specific */ +#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1 Chip */ +#define CONFIG_MPC8540 1 /* MPC8540 specific */ #define CONFIG_MPC8540ADS 1 /* MPC8540ADS board specific*/ -#undef CONFIG_PCI /* pci ethernet support */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#undef CONFIG_PCI /* pci ethernet support */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ #if defined(CONFIG_MPC85xx_REV1) -#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_DLL /* possible DLL fix needed */ #endif /* Using Localbus SDRAM to emulate flash before we can program the flash, @@ -53,24 +53,24 @@ */ #undef CONFIG_RAM_AS_FLASH -#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */ +#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */ #define CONFIG_SYS_CLK_FREQ 66000000 /* sysclk for MPC85xx */ #else #define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */ #endif -#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */ +#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */ #define CONFIG_DDR_SETTING #endif /* below can be toggled for performance analysis. otherwise use default */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#undef CONFIG_BTB /* toggle branch predition */ -#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#undef CONFIG_BTB /* toggle branch predition */ +#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#undef CFG_DRAM_TEST /* memory test, takes time */ +#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ #define CFG_MEMTEST_END 0x00400000 @@ -82,13 +82,13 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ #define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE -#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */ +#define CFG_SDRAM_SIZE 128 /* DDR is now 128MB */ #if defined(CONFIG_RAM_AS_FLASH) #define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ @@ -98,44 +98,44 @@ #define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ +#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ #define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */ #else /* Boot from real Flash */ -#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ +#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ #define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ #endif -#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ +#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ +#define CFG_MAX_FLASH_SECT 64 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms)*/ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) #define CFG_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CFG_RAMBOOT #endif #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ #if defined(CONFIG_DDR_SETTING) -#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ -#define CFG_DDR_CS0_CONFIG 0x80000002 -#define CFG_DDR_TIMING_1 0x37344321 -#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/ -#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/ -#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ -#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/ +#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ +#define CFG_DDR_CS0_CONFIG 0x80000002 +#define CFG_DDR_TIMING_1 0x37344321 +#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/ +#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/ +#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ +#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/ #endif #undef CONFIG_CLOCKS_IN_MHZ /* local bus definitions */ -#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ +#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ #define CFG_OR2_PRELIM 0xfc006901 #define CFG_LBC_LCRR 0x00030004 /* local bus freq divider*/ #define CFG_LBC_LBCR 0x00000000 @@ -148,52 +148,52 @@ #define CFG_LBC_LSDMR_5 0x4061b723 #if defined(CONFIG_RAM_AS_FLASH) -#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ +#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */ #else -#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */ +#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */ #endif -#define CFG_OR4_PRELIM 0xffffe1f1 -#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000) +#define CFG_OR4_PRELIM 0xffffe1f1 +#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000) #define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_NS16550 #define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_REG_SIZE 1 #define CFG_NS16550_CLK get_bus_freq(0) -#define CONFIG_BAUDRATE 115200 +#define CONFIG_BAUDRATE 115200 #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) /* Use the HUSH parser */ #define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER #define CFG_PROMPT_HUSH_PS2 "> " #endif /* I2C */ -#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ /* General PCI */ #define CFG_PCI_MEM_BASE 0xe0000000 @@ -203,22 +203,22 @@ #define CONFIG_NET_MULTI #undef CONFIG_EEPRO100 #define CONFIG_TULIP -#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ #if !defined(CONFIG_PCI_PNP) - #define PCI_ENET0_IOADDR 0xe0000000 - #define PCI_ENET0_MEMADDR 0xe0000000 - #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/ + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/ #endif -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 8 */ #define CFG_PCI_SUBSYS_DEVICEID 0x0003 #else #define CFG_PCI_SUBSYS_DEVICEID 0x0008 #endif #elif defined(CONFIG_TSEC_ENET) -#define CONFIG_NET_MULTI 1 -#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ +#define CONFIG_NET_MULTI 1 +#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 8 /* PHY address */ #endif @@ -232,7 +232,7 @@ #else #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) - #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ + #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #endif #define CFG_ENV_SIZE 0x2000 #else @@ -242,10 +242,10 @@ #define CFG_ENV_SIZE 0x2000 #endif -#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200" +#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200" /*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/ #define CONFIG_BOOTCOMMAND "bootm 0xff300000 0xff700000" -#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ +#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ @@ -274,7 +274,7 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "MPC8540ADS=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else @@ -291,10 +291,10 @@ * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 +#define CFG_DCACHE_SIZE 32768 #define CFG_CACHELINE_SIZE 32 #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ @@ -315,17 +315,17 @@ /* NOTE: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) -#define CONFIG_ETHADDR 00:01:af:07:9b:8a -#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b -#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c +#define CONFIG_ETHADDR 00:01:af:07:9b:8a +#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b +#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c #endif -#define CONFIG_SERVERIP 163.12.64.52 -#define CONFIG_IPADDR 10.82.0.105 -#define CONFIG_GATEWAYIP 10.82.1.254 -#define CONFIG_NETMASK 255.255.254.0 -#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003 -#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx -#define CONFIG_BOOTFILE pImage +#define CONFIG_SERVERIP 163.12.64.52 +#define CONFIG_IPADDR 10.82.0.105 +#define CONFIG_GATEWAYIP 10.82.1.254 +#define CONFIG_NETMASK 255.255.254.0 +#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003 +#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx +#define CONFIG_BOOTFILE pImage #endif /* __CONFIG_H */ |
