diff options
Diffstat (limited to 'include/configs/MPC837XERDB.h')
| -rw-r--r-- | include/configs/MPC837XERDB.h | 348 |
1 files changed, 174 insertions, 174 deletions
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index 4650b8d9b4..f281c59d3c 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -58,7 +58,7 @@ /* * Hardware Reset Configuration Word */ -#define CFG_HRCW_LOW (\ +#define CONFIG_SYS_HRCW_LOW (\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ HRCWL_DDR_TO_SCB_CLK_1X1 |\ HRCWL_SVCOD_DIV_2 |\ @@ -66,7 +66,7 @@ HRCWL_CORE_TO_CSB_2X1) #ifdef CONFIG_PCISLAVE -#define CFG_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_AGENT |\ HRCWH_PCI1_ARBITER_DISABLE |\ HRCWH_CORE_ENABLE |\ @@ -80,7 +80,7 @@ HRCWH_BIG_ENDIAN |\ HRCWH_LDP_CLEAR) #else -#define CFG_HRCW_HIGH (\ +#define CONFIG_SYS_HRCW_HIGH (\ HRCWH_PCI_HOST |\ HRCWH_PCI1_ARBITER_ENABLE |\ HRCWH_CORE_ENABLE |\ @@ -95,36 +95,36 @@ HRCWH_LDP_CLEAR) #endif -/* System performance - define the value i.e. CFG_XXX +/* System performance - define the value i.e. CONFIG_SYS_XXX */ /* Arbiter Configuration Register */ -#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ -#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ /* System Priority Control Regsiter */ -#define CFG_SPCR_TSECEP 3 /* eTSEC1&2 emergency priority (0-3) */ +#define CONFIG_SYS_SPCR_TSECEP 3 /* eTSEC1&2 emergency priority (0-3) */ /* System Clock Configuration Register */ -#define CFG_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */ -#define CFG_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */ -#define CFG_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */ +#define CONFIG_SYS_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */ +#define CONFIG_SYS_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */ +#define CONFIG_SYS_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */ /* * System IO Config */ -#define CFG_SICRH 0x08200000 -#define CFG_SICRL 0x00000000 +#define CONFIG_SYS_SICRH 0x08200000 +#define CONFIG_SYS_SICRL 0x00000000 /* * Output Buffer Impedance */ -#define CFG_OBIR 0x30100000 +#define CONFIG_SYS_OBIR 0x30100000 /* * IMMR new address */ -#define CFG_IMMR 0xE0000000 +#define CONFIG_SYS_IMMR 0xE0000000 /* * Device configurations @@ -145,13 +145,13 @@ /* * DDR Setup */ -#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CFG_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDR_SDRAM_CLK_CNTL 0x03000000 -#define CFG_83XX_DDR_USES_CS0 +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x03000000 +#define CONFIG_SYS_83XX_DDR_USES_CS0 -#define CFG_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN) +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN) #undef CONFIG_DDR_ECC /* support DDR ECC function */ #undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ @@ -161,13 +161,13 @@ /* * Manually set up DDR parameters */ -#define CFG_DDR_SIZE 256 /* MB */ -#define CFG_DDR_CS0_BNDS 0x0000000f -#define CFG_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ODT_WR_ACS \ +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ODT_WR_ACS \ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10) -#define CFG_DDR_TIMING_3 0x00000000 -#define CFG_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ | (0 << TIMING_CFG0_WRT_SHIFT) \ | (0 << TIMING_CFG0_RRT_SHIFT) \ | (0 << TIMING_CFG0_WWT_SHIFT) \ @@ -177,7 +177,7 @@ | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) /* 0x00220802 */ /* 0x00260802 */ /* DDR400 */ -#define CFG_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ +#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ | (7 << TIMING_CFG1_CASLAT_SHIFT) \ @@ -187,125 +187,125 @@ | (2 << TIMING_CFG1_WRTORD_SHIFT)) /* 0x3935d322 */ /* 0x3937d322 */ -#define CFG_DDR_TIMING_2 0x02984cc8 +#define CONFIG_SYS_DDR_TIMING_2 0x02984cc8 -#define CFG_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \ +#define CONFIG_SYS_DDR_INTERVAL ((1545 << SDRAM_INTERVAL_REFINT_SHIFT) \ | (256 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) /* 0x06090100 */ #if defined(CONFIG_DDR_2T_TIMING) -#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \ | SDRAM_CFG_2T_EN \ | SDRAM_CFG_DBW_32) #else -#define CFG_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ | 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT) /* 0x43000000 */ #endif -#define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ -#define CFG_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ +#define CONFIG_SYS_DDR_MODE ((0x0440 << SDRAM_MODE_ESD_SHIFT) \ | (0x0442 << SDRAM_MODE_SD_SHIFT)) /* 0x04400442 */ /* DDR400 */ -#define CFG_DDR_MODE2 0x00000000 +#define CONFIG_SYS_DDR_MODE2 0x00000000 /* * Memory test */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00040000 /* memtest region */ -#define CFG_MEMTEST_END 0x0ef70010 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00040000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x0ef70010 /* * The reserved memory */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ /* * Initial RAM Base Address Setup */ -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* * Local Bus Configuration & Clock Setup */ -#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) -#define CFG_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) +#define CONFIG_SYS_LBC_LBCR 0x00000000 /* * FLASH on the Local Bus */ -#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ +#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ -#define CFG_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ -#define CFG_FLASH_EMPTY_INFO /* display empty sectors */ -#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ -#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ -#define CFG_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016 /* 8 MB window size */ -#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ -#define CFG_OR0_PRELIM (0xFF800000 /* 8 MByte */ \ +#define CONFIG_SYS_OR0_PRELIM (0xFF800000 /* 8 MByte */ \ | OR_GPCM_XACS \ | OR_GPCM_SCY_9 \ | OR_GPCM_EHTR \ | OR_GPCM_EAD) /* 0xFF806FF7 TODO SLOW 8 MB flash size */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ /* * NAND Flash on the Local Bus */ -#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ -#define CFG_BR1_PRELIM (CFG_NAND_BASE | \ +#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | \ (2 << BR_DECC_SHIFT) | /* Use HW ECC */ \ BR_PS_8 | /* Port Size = 8 bit */ \ BR_MS_FCM | /* MSEL = FCM */ \ BR_V) /* valid */ -#define CFG_OR1_PRELIM (0xFFFF8000 | /* length 32K */ \ +#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 | /* length 32K */ \ OR_FCM_CSCT | \ OR_FCM_CST | \ OR_FCM_CHT | \ OR_FCM_SCY_1 | \ OR_FCM_TRLX | \ OR_FCM_EHTR) -#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE -#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ /* Vitesse 7385 */ -#define CFG_VSC7385_BASE 0xF0000000 +#define CONFIG_SYS_VSC7385_BASE 0xF0000000 #ifdef CONFIG_VSC7385_ENET -#define CFG_BR2_PRELIM 0xf0000801 /* Base address */ -#define CFG_OR2_PRELIM 0xfffe09ff /* 128K bytes*/ -#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE /* Access Base */ -#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access Size 128K */ +#define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* Base address */ +#define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* 128K bytes*/ +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE /* Access Base */ +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* Access Size 128K */ #endif @@ -314,16 +314,16 @@ */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) -#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) /* SERDES */ #define CONFIG_FSL_SERDES @@ -331,9 +331,9 @@ #define CONFIG_FSL_SERDES2 0xe3100 /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* Pass open firmware flat tree */ @@ -345,42 +345,42 @@ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_FSL_I2C -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 -#define CFG_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x51} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * Config on-board RTC */ #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ /* * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI_MEM_BASE 0x80000000 -#define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE -#define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCI_MMIO_BASE 0x90000000 -#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE -#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ -#define CFG_PCI_IO_BASE 0x00000000 -#define CFG_PCI_IO_PHYS 0xE0300000 -#define CFG_PCI_IO_SIZE 0x100000 /* 1M */ - -#define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE -#define CFG_PCI_SLV_MEM_BUS 0x00000000 -#define CFG_PCI_SLV_MEM_SIZE 0x80000000 +#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE +#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE +#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 +#define CONFIG_SYS_PCI_IO_SIZE 0x100000 /* 1M */ + +#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 +#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 #ifdef CONFIG_PCI #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ #endif /* CONFIG_PCI */ /* @@ -396,7 +396,7 @@ #ifdef CONFIG_TSEC1 #define CONFIG_HAS_ETH0 #define CONFIG_TSEC1_NAME "TSEC0" -#define CFG_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 #define TSEC1_PHY_ADDR 2 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC1_PHYIDX 0 @@ -405,7 +405,7 @@ #ifdef CONFIG_TSEC2 #define CONFIG_HAS_ETH1 #define CONFIG_TSEC2_NAME "TSEC1" -#define CFG_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 #define TSEC2_PHY_ADDR 0x1c #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) #define TSEC2_PHYIDX 0 @@ -422,15 +422,15 @@ #define CONFIG_LIBATA #define CONFIG_FSL_SATA -#define CFG_SATA_MAX_DEVICE 2 +#define CONFIG_SYS_SATA_MAX_DEVICE 2 #define CONFIG_SATA1 -#define CFG_SATA1_OFFSET 0x18000 -#define CFG_SATA1 (CFG_IMMR + CFG_SATA1_OFFSET) -#define CFG_SATA1_FLAGS FLAGS_DMA +#define CONFIG_SYS_SATA1_OFFSET 0x18000 +#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) +#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA #define CONFIG_SATA2 -#define CFG_SATA2_OFFSET 0x19000 -#define CFG_SATA2 (CFG_IMMR + CFG_SATA2_OFFSET) -#define CFG_SATA2_FLAGS FLAGS_DMA +#define CONFIG_SYS_SATA2_OFFSET 0x19000 +#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) +#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA #ifdef CONFIG_FSL_SATA #define CONFIG_LBA48 @@ -442,20 +442,20 @@ /* * Environment */ -#ifndef CFG_RAMBOOT +#ifndef CONFIG_SYS_RAMBOOT #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE+CFG_MONITOR_LEN) + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */ #define CONFIG_ENV_SIZE 0x4000 #else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-0x1000) + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options @@ -480,7 +480,7 @@ #define CONFIG_CMD_PCI #endif -#if defined(CFG_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #endif @@ -492,34 +492,34 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup */ -#define CFG_HID0_INIT 0x000000000 -#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK -#define CFG_HID2 HID2_HBE +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK +#define CONFIG_SYS_HID2 HID2_HBE /* * MMU Setup @@ -528,67 +528,67 @@ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ -#define CFG_SDRAM_LOWER CFG_SDRAM_BASE -#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) +#define CONFIG_SYS_SDRAM_LOWER CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_SDRAM_UPPER (CONFIG_SYS_SDRAM_BASE + 0x10000000) -#define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT0L CFG_IBAT0L -#define CFG_DBAT0U CFG_IBAT0U +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT1L CFG_IBAT1L -#define CFG_DBAT1U CFG_IBAT1U +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ -#define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) -#define CFG_DBAT2L CFG_IBAT2L -#define CFG_DBAT2U CFG_IBAT2U +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U /* L2 Switch: cache-inhibit and guarded */ -#define CFG_IBAT3L (CFG_VSC7385_BASE | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_VSC7385_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT3U (CFG_VSC7385_BASE | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_DBAT3L CFG_IBAT3L -#define CFG_DBAT3U CFG_IBAT3U +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_VSC7385_BASE | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U /* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT4U CFG_IBAT4U +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U /* Stack in dcache: cacheable, no memory coherence */ -#define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) -#define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_DBAT5L CFG_IBAT5L -#define CFG_DBAT5U CFG_IBAT5U +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U #ifdef CONFIG_PCI /* PCI MEM space: cacheable */ -#define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U /* PCI MMIO space: cache-inhibit and guarded */ -#define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ +#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #else -#define CFG_IBAT6L (0) -#define CFG_IBAT6U (0) -#define CFG_IBAT7L (0) -#define CFG_IBAT7U (0) -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT6L (0) +#define CONFIG_SYS_IBAT6U (0) +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #endif /* |
