diff options
Diffstat (limited to 'include/configs/MPC8313ERDB.h')
| -rw-r--r-- | include/configs/MPC8313ERDB.h | 354 |
1 files changed, 177 insertions, 177 deletions
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 30c4243228..fc3fa13c7a 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -49,9 +49,9 @@ #define CONFIG_VSC7385_ENET #define CONFIG_TSEC2 -#ifdef CFG_66MHZ +#ifdef CONFIG_SYS_66MHZ #define CONFIG_83XX_CLKIN 66666667 /* in Hz */ -#elif defined(CFG_33MHZ) +#elif defined(CONFIG_SYS_33MHZ) #define CONFIG_83XX_CLKIN 33333333 /* in Hz */ #else #error Unknown oscillator frequency. @@ -61,23 +61,23 @@ #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ -#define CFG_IMMR 0xE0000000 +#define CONFIG_SYS_IMMR 0xE0000000 #if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CONFIG_DEFAULT_IMMR CFG_IMMR +#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR #endif -#define CFG_MEMTEST_START 0x00001000 -#define CFG_MEMTEST_END 0x07f00000 +#define CONFIG_SYS_MEMTEST_START 0x00001000 +#define CONFIG_SYS_MEMTEST_END 0x07f00000 /* Early revs of this board will lock up hard when attempting * to access the PMC registers, unless a JTAG debugger is * connected, or some resistor modifications are made. */ -#define CFG_8313ERDB_BROKEN_PMC 1 +#define CONFIG_SYS_8313ERDB_BROKEN_PMC 1 -#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ -#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ +#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ +#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ /* * Device configurations @@ -98,22 +98,22 @@ /* * DDR Setup */ -#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_BASE -#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE /* * Manually set up DDR parameters, as this board does not * seem to have the SPD connected to I2C. */ -#define CFG_DDR_SIZE 128 /* MB */ -#define CFG_DDR_CONFIG ( CSCONFIG_EN \ +#define CONFIG_SYS_DDR_SIZE 128 /* MB */ +#define CONFIG_SYS_DDR_CONFIG ( CSCONFIG_EN \ | 0x00010000 /* TODO */ \ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 ) /* 0x80010102 */ -#define CFG_DDR_TIMING_3 0x00000000 -#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 +#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ @@ -122,7 +122,7 @@ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) /* 0x00220802 */ -#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ +#define CONFIG_SYS_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ | ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ @@ -131,7 +131,7 @@ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) /* 0x3835a322 */ -#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ +#define CONFIG_SYS_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \ | ( 5 << TIMING_CFG2_CPO_SHIFT ) \ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ | ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ @@ -139,30 +139,30 @@ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ | ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) ) /* 0x129048c6 */ /* P9-45,may need tuning */ -#define CFG_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \ +#define CONFIG_SYS_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \ | ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) /* 0x05100500 */ #if defined(CONFIG_DDR_2T_TIMING) -#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \ +#define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \ | SDRAM_CFG_SDRAM_TYPE_DDR2 \ | SDRAM_CFG_2T_EN \ | SDRAM_CFG_DBW_32 ) #else -#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \ +#define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \ | SDRAM_CFG_SDRAM_TYPE_DDR2 \ | SDRAM_CFG_32_BE ) /* 0x43080000 */ #endif -#define CFG_SDRAM_CFG2 0x00401000 +#define CONFIG_SYS_SDRAM_CFG2 0x00401000 /* set burst length to 8 for 32-bit data path */ -#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \ +#define CONFIG_SYS_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \ | ( 0x0632 << SDRAM_MODE_SD_SHIFT ) ) /* 0x44480632 */ -#define CFG_DDR_MODE_2 0x8000C000 +#define CONFIG_SYS_DDR_MODE_2 0x8000C000 -#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 +#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 /*0x02000000*/ -#define CFG_DDRCDR_VALUE ( DDRCDR_EN \ +#define CONFIG_SYS_DDRCDR_VALUE ( DDRCDR_EN \ | DDRCDR_PZ_NOMZ \ | DDRCDR_NZ_NOMZ \ | DDRCDR_M_ODR ) @@ -170,86 +170,86 @@ /* * FLASH on the Local Bus */ -#define CFG_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */ -#define CFG_FLASH_SIZE 8 /* flash size in MB */ -#define CFG_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ -#define CFG_FLASH_EMPTY_INFO /* display empty sectors */ -#define CFG_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ +#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */ -#define CFG_NOR_BR_PRELIM (CFG_FLASH_BASE | /* flash Base address */ \ +#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE | /* flash Base address */ \ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ -#define CFG_NOR_OR_PRELIM ( 0xFF800000 /* 8 MByte */ \ +#define CONFIG_SYS_NOR_OR_PRELIM ( 0xFF800000 /* 8 MByte */ \ | OR_GPCM_XACS \ | OR_GPCM_SCY_9 \ | OR_GPCM_EHTR \ | OR_GPCM_EAD ) /* 0xFF006FF7 TODO SLOW 16 MB flash size */ -#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */ -#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* window base at flash base */ +#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000017 /* 16 MB window size */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 135 /* sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */ -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) && !defined(CONFIG_NAND_SPL) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) && !defined(CONFIG_NAND_SPL) +#define CONFIG_SYS_RAMBOOT #endif -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/ -#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -/* CFG_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ +/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ /* * Local Bus LCRR and LBCR regs */ -#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4 -#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \ +#define CONFIG_SYS_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4 +#define CONFIG_SYS_LBC_LBCR ( 0x00040000 /* TODO */ \ | (0xFF << LBCR_BMT_SHIFT) \ | 0xF ) /* 0x0004ff0f */ -#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */ +#define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */ /* drivers/mtd/nand/nand.c */ #ifdef CONFIG_NAND_SPL -#define CFG_NAND_BASE 0xFFF00000 +#define CONFIG_SYS_NAND_BASE 0xFFF00000 #else -#define CFG_NAND_BASE 0xE2800000 +#define CONFIG_SYS_NAND_BASE 0xE2800000 #endif -#define CFG_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 #define CONFIG_MTD_NAND_VERIFY_WRITE #define CONFIG_CMD_NAND 1 #define CONFIG_NAND_FSL_ELBC 1 -#define CFG_NAND_BLOCK_SIZE 16384 +#define CONFIG_SYS_NAND_BLOCK_SIZE 16384 -#define CFG_NAND_U_BOOT_SIZE (512 << 10) -#define CFG_NAND_U_BOOT_DST 0x00100000 -#define CFG_NAND_U_BOOT_START 0x00100100 -#define CFG_NAND_U_BOOT_OFFS 16384 -#define CFG_NAND_U_BOOT_RELOC 0x00010000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) +#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 16384 +#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 -#define CFG_NAND_BR_PRELIM ( CFG_NAND_BASE \ +#define CONFIG_SYS_NAND_BR_PRELIM ( CONFIG_SYS_NAND_BASE \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ | BR_MS_FCM /* MSEL = FCM */ \ | BR_V ) /* valid */ -#define CFG_NAND_OR_PRELIM ( 0xFFFF8000 /* length 32K */ \ +#define CONFIG_SYS_NAND_OR_PRELIM ( 0xFFFF8000 /* length 32K */ \ | OR_FCM_CSCT \ | OR_FCM_CST \ | OR_FCM_CHT \ @@ -259,39 +259,39 @@ /* 0xFFFF8396 */ #ifdef CONFIG_NAND_U_BOOT -#define CFG_BR0_PRELIM CFG_NAND_BR_PRELIM -#define CFG_OR0_PRELIM CFG_NAND_OR_PRELIM -#define CFG_BR1_PRELIM CFG_NOR_BR_PRELIM -#define CFG_OR1_PRELIM CFG_NOR_OR_PRELIM +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NOR_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NOR_OR_PRELIM #else -#define CFG_BR0_PRELIM CFG_NOR_BR_PRELIM -#define CFG_OR0_PRELIM CFG_NOR_OR_PRELIM -#define CFG_BR1_PRELIM CFG_NAND_BR_PRELIM -#define CFG_OR1_PRELIM CFG_NAND_OR_PRELIM +#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM +#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM #endif -#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE -#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */ -#define CFG_NAND_LBLAWBAR_PRELIM CFG_LBLAWBAR1_PRELIM -#define CFG_NAND_LBLAWAR_PRELIM CFG_LBLAWAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM +#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM /* local bus read write buffer mapping */ -#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */ -#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */ -#define CFG_LBLAWBAR3_PRELIM 0xFA000000 -#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ +#define CONFIG_SYS_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */ +#define CONFIG_SYS_OR3_PRELIM 0xFFFF8FF7 /* 32kB */ +#define CONFIG_SYS_LBLAWBAR3_PRELIM 0xFA000000 +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ /* Vitesse 7385 */ -#define CFG_VSC7385_BASE 0xF0000000 +#define CONFIG_SYS_VSC7385_BASE 0xF0000000 #ifdef CONFIG_VSC7385_ENET -#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */ -#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/ -#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */ -#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */ +#define CONFIG_SYS_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */ +#define CONFIG_SYS_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/ +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VSC7385_BASE/* Access window base at VSC7385 base */ +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */ #endif @@ -304,47 +304,47 @@ * Serial Port */ #define CONFIG_CONS_INDEX 1 -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} -#define CFG_NS16550_COM1 (CFG_IMMR+0x4500) -#define CFG_NS16550_COM2 (CFG_IMMR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #define CONFIG_FSL_I2C #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3000 -#define CFG_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 /* * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCI1_MMIO_BASE 0x90000000 -#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE -#define CFG_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CFG_PCI1_IO_BASE 0x00000000 -#define CFG_PCI1_IO_PHYS 0xE2000000 -#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ /* * TSEC @@ -357,7 +357,7 @@ #ifdef CONFIG_TSEC1 #define CONFIG_HAS_ETH0 #define CONFIG_TSEC1_NAME "TSEC0" -#define CFG_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 #define TSEC1_PHY_ADDR 0x1c #define TSEC1_FLAGS TSEC_GIGABIT #define TSEC1_PHYIDX 0 @@ -366,7 +366,7 @@ #ifdef CONFIG_TSEC2 #define CONFIG_HAS_ETH1 #define CONFIG_TSEC2_NAME "TSEC1" -#define CFG_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 #define TSEC2_PHY_ADDR 4 #define TSEC2_FLAGS TSEC_GIGABIT #define TSEC2_PHYIDX 0 @@ -380,7 +380,7 @@ * Configure on-board RTC */ #define CONFIG_RTC_DS1337 -#define CFG_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* * Environment @@ -388,26 +388,26 @@ #if defined(CONFIG_NAND_U_BOOT) #define CONFIG_ENV_IS_IN_NAND 1 #define CONFIG_ENV_OFFSET (512 * 1024) - #define CONFIG_ENV_SECT_SIZE CFG_NAND_BLOCK_SIZE + #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4) #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) -#elif !defined(CFG_RAMBOOT) +#elif !defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ #define CONFIG_ENV_SIZE 0x2000 /* Address and size of Redundant Environment Sector */ #else #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options @@ -430,7 +430,7 @@ #define CONFIG_CMD_DATE #define CONFIG_CMD_PCI -#if defined(CFG_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT) +#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #endif @@ -441,30 +441,30 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ -#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */ +#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ -#ifdef CFG_66MHZ +#ifdef CONFIG_SYS_66MHZ /* 66MHz IN, 133MHz CSB, 266 DDR, 266 CORE */ /* 0x62040000 */ -#define CFG_HRCW_LOW (\ +#define CONFIG_SYS_HRCW_LOW (\ 0x20000000 /* reserved, must be set */ |\ HRCWL_DDRCM |\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ @@ -472,13 +472,13 @@ HRCWL_CSB_TO_CLKIN_2X1 |\ HRCWL_CORE_TO_CSB_2X1) -#define CFG_NS16550_CLK (CONFIG_83XX_CLKIN * 2) +#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2) -#elif defined(CFG_33MHZ) +#elif defined(CONFIG_SYS_33MHZ) /* 33MHz IN, 165MHz CSB, 330 DDR, 330 CORE */ /* 0x65040000 */ -#define CFG_HRCW_LOW (\ +#define CONFIG_SYS_HRCW_LOW (\ 0x20000000 /* reserved, must be set */ |\ HRCWL_DDRCM |\ HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ @@ -486,11 +486,11 @@ HRCWL_CSB_TO_CLKIN_5X1 |\ HRCWL_CORE_TO_CSB_2X1) -#define CFG_NS16550_CLK (CONFIG_83XX_CLKIN * 5) +#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 5) #endif -#define CFG_HRCW_HIGH_BASE (\ +#define CONFIG_SYS_HRCW_HIGH_BASE (\ HRCWH_PCI_HOST |\ HRCWH_PCI1_ARBITER_ENABLE |\ HRCWH_CORE_ENABLE |\ @@ -501,72 +501,72 @@ HRCWH_BIG_ENDIAN) #ifdef CONFIG_NAND_SPL -#define CFG_HRCW_HIGH (CFG_HRCW_HIGH_BASE |\ +#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ HRCWH_FROM_0XFFF00100 |\ HRCWH_ROM_LOC_NAND_SP_8BIT |\ HRCWH_RL_EXT_NAND) #else -#define CFG_HRCW_HIGH (CFG_HRCW_HIGH_BASE |\ +#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE |\ HRCWH_FROM_0X00000100 |\ HRCWH_ROM_LOC_LOCAL_16BIT |\ HRCWH_RL_EXT_LEGACY) #endif /* System IO Config */ -#define CFG_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */ -#define CFG_SICRL SICRL_USBDR /* Enable Internal USB Phy */ +#define CONFIG_SYS_SICRH (SICRH_TSOBI1 | SICRH_TSOBI2) /* RGMII */ +#define CONFIG_SYS_SICRL SICRL_USBDR /* Enable Internal USB Phy */ -#define CFG_HID0_INIT 0x000000000 -#define CFG_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) -#define CFG_HID2 HID2_HBE +#define CONFIG_SYS_HID2 HID2_HBE #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR @ 0x00000000 */ -#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10) -#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) /* PCI @ 0x80000000 */ -#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10) -#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) /* PCI2 not supported on 8313 */ -#define CFG_IBAT3L (0) -#define CFG_IBAT3U (0) -#define CFG_IBAT4L (0) -#define CFG_IBAT4U (0) +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ -#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ -#define CFG_IBAT6L (0xF0000000 | BATL_PP_10) -#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CFG_IBAT7L (0) -#define CFG_IBAT7U (0) - -#define CFG_DBAT0L CFG_IBAT0L -#define CFG_DBAT0U CFG_IBAT0U -#define CFG_DBAT1L CFG_IBAT1L -#define CFG_DBAT1U CFG_IBAT1U -#define CFG_DBAT2L CFG_IBAT2L -#define CFG_DBAT2U CFG_IBAT2U -#define CFG_DBAT3L CFG_IBAT3L -#define CFG_DBAT3U CFG_IBAT3U -#define CFG_DBAT4L CFG_IBAT4L -#define CFG_DBAT4U CFG_IBAT4U -#define CFG_DBAT5L CFG_IBAT5L -#define CFG_DBAT5U CFG_IBAT5U -#define CFG_DBAT6L CFG_IBAT6L -#define CFG_DBAT6U CFG_IBAT6U -#define CFG_DBAT7L CFG_IBAT7L -#define CFG_DBAT7U CFG_IBAT7U +#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10) +#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) + +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U /* * Internal Definitions |
