diff options
Diffstat (limited to 'include/configs/AMX860.h')
| -rw-r--r-- | include/configs/AMX860.h | 297 |
1 files changed, 297 insertions, 0 deletions
diff --git a/include/configs/AMX860.h b/include/configs/AMX860.h new file mode 100644 index 0000000000..420cd085f1 --- /dev/null +++ b/include/configs/AMX860.h @@ -0,0 +1,297 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC860 1 +#define CONFIG_AMX860 1 + +#undef CONFIG_8xx_CONS_SMC1 /* Console is on SCC2 */ +#undef CONFIG_8xx_CONS_SMC2 +#define CONFIG_8xx_CONS_SCC2 1 +#undef CONFIG_8xx_CONS_NONE +#define CONFIG_BAUDRATE 9600 +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ + +#define MPC8XX_FACT 10 /* Multiply by 10 */ +#define MPC8XX_XIN 5000000 /* 5 MHz in */ +#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) + +#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" /* autoboot command */ + +#undef CONFIG_BOOTARGS + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */ +#define CONFIG_KGDB_BAUDRATE 9600 /* speed to run kgdb serial port at */ +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */ + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_DHCP | \ + CFG_CMD_DATE ) + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0200000 /* 1 ... 4 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x00100000 + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * U-Boot for AMX board supports two types of memory extension + * modules: one that provides 4 MB flash memory, and another one with + * 16 MB EDO DRAM. + * + * The flash module swaps the CS0 and CS1 signals: if the module is + * installed, CS0 is connected to Flash on the module and CS1 is + * connected to the on-board Flash. This means that you must intall + * U-Boot when the Flash module is plugged in, if you plan to use + * it. + * + * To enable support for the DRAM extension card, CONFIG_AMX_RAM_EXT + * must be defined. The DRAM module uses CS1. + * + * Only one of these modules may be installed at a time. If U-Boot + * is compiled with the CONFIG_AMX_RAM_EXT option set, it will not + * work if the Flash extension module is installed instead of the + * DRAM module. + */ +#define CONFIG_AMX_RAM_EXT /* 16Mb Ext. DRAM module support */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + * + * Use 4 MB for without and 8 MB with 16 MB DRAM extension module + * (CONFIG_AMX_RAM_EXT) + */ +#ifdef CONFIG_AMX_RAM_EXT +# define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#else +# define CFG_BOOTMAPSZ (4 << 20) /* Initial Memory map for Linux */ +#endif +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * set the PLL, the low-power modes and the reset control (15-29) + */ +#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) + +/*----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR (SCCR_TBS|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00) + +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ +#ifndef CONFIG_AMX_RAM_EXT +#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #1 */ +#endif + +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFFC00000 /* OR addr mask */ + +/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ +/* 0x00000800 0x00000400 0x00000100 0x00000030 0x00000004 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_5_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) + +#define CFG_OR0_PRELIM 0xFFC00954 /* Real values for the board */ +#define CFG_BR0_PRELIM 0x40000001 /* Real values for the board */ + +#ifndef CONFIG_AMX_RAM_EXT +#define CFG_OR1_REMAP CFG_OR0_REMAP +#define CFG_OR1_PRELIM 0xFFC00954 /* Real values for the board */ +#define CFG_BR1_PRELIM 0x60000001 /* Real values for the board */ +#endif + +/* DSP ("Glue") Xilinx */ +#define CFG_OR6_PRELIM 0xFFFF8000 /* 32kB, 15 waits, cs after addr, no bursts */ +#define CFG_BR6_PRELIM 0x60000401 /* use GPCM for CS generation, 8 bit port */ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#endif /* __CONFIG_H */ |
