diff options
Diffstat (limited to 'doc/README.mpc8315erdb')
| -rw-r--r-- | doc/README.mpc8315erdb | 105 |
1 files changed, 0 insertions, 105 deletions
diff --git a/doc/README.mpc8315erdb b/doc/README.mpc8315erdb deleted file mode 100644 index b32132d053..0000000000 --- a/doc/README.mpc8315erdb +++ /dev/null @@ -1,105 +0,0 @@ -Freescale MPC8315ERDB Board ------------------------------------------ - -1. Board Switches and Jumpers - - S3 is used to set CONFIG_SYS_RESET_SOURCE. - - To boot the image at 0xFE000000 in NOR flash, use these DIP - switch settings for S3 S4: - - +------+ +------+ - | | | **** | - | **** | | | - +------+ ON +------+ ON - 4321 4321 - (where the '*' indicates the position of the tab of the switch.) - - To boot the image at the beginning of NAND flash, use these - DIP switch settings for S3 S4: - - +------+ +------+ - | * | | *** | - | *** | | * | - +------+ ON +------+ ON - 4321 4321 - (where the '*' indicates the position of the tab of the switch.) - - When booting from NAND, use u-boot-nand.bin, not u-boot.bin. - -2. Memory Map - The memory map looks like this: - - 0x0000_0000 0x07ff_ffff DDR 128M - 0x8000_0000 0x8fff_ffff PCI MEM 256M - 0x9000_0000 0x9fff_ffff PCI_MMIO 256M - 0xe000_0000 0xe00f_ffff IMMR 1M - 0xe030_0000 0xe03f_ffff PCI IO 1M - 0xe060_0000 0xe060_7fff NAND FLASH (CS1) 32K - 0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M - - When booting from NAND, NAND flash is CS0 and NOR flash - is CS1. - -3. Definitions - -3.1 Explanation of NEW definitions in: - - include/configs/MPC8315ERDB.h - - CONFIG_MPC83xx MPC83xx family - CONFIG_MPC831x MPC831x specific - CONFIG_MPC8315 MPC8315 specific - CONFIG_MPC8315ERDB MPC8315ERDB board specific - -4. Compilation - - Assuming you're using BASH (or similar) as your shell: - - export CROSS_COMPILE=your-cross-compiler-prefix- - make distclean - make MPC8315ERDB_config (or MPC8315ERDB_NAND_config for u-boot-nand.bin) - make all - -5. Downloading and Flashing Images - -5.1 Reflash U-boot Image using U-boot - - NOR flash: - - tftp 40000 u-boot.bin - protect off all - erase fe000000 fe1fffff - - cp.b 40000 fe000000 xxxx - protect on all - - You have to supply the correct byte count with 'xxxx' - from the TFTP result log. - - NAND flash: - - =>tftpboot $loadaddr <filename> - =>nand erase 0 0x80000 - =>nand write $loadaddr 0 0x80000 - - ...where 0x80000 is the filesize rounded up to - the next 0x20000 increment. - -5.2 Downloading and Booting Linux Kernel - - Ensure that all networking-related environment variables are set - properly (including ipaddr, serverip, gatewayip (if needed), - netmask, ethaddr, eth1addr, rootpath (if using NFS root), - fdtfile, and bootfile). - - Then, do one of the following, depending on whether you - want an NFS root or a ramdisk root: - - =>run nfsboot - or - =>run ramboot - -6 Notes - - The console baudrate for MPC8315ERDB is 115200bps. |
