diff options
Diffstat (limited to 'board')
57 files changed, 2156 insertions, 624 deletions
diff --git a/board/LaCie/common/cpld-gpio-bus.c b/board/LaCie/common/cpld-gpio-bus.c new file mode 100644 index 0000000000..fb9bf8d5db --- /dev/null +++ b/board/LaCie/common/cpld-gpio-bus.c @@ -0,0 +1,50 @@ +/* + * cpld-gpio-bus.c: provides support for the CPLD GPIO bus found on some LaCie + * boards (as the 2Big/5Big Network v2 and the 2Big NAS). This parallel GPIO + * bus exposes two registers (address and data). Each of this register is made + * up of several dedicated GPIOs. An extra GPIO is used to notify the CPLD that + * the registers have been updated. + * + * Mostly this bus is used to configure the LEDs on LaCie boards. + * + * Copyright (C) 2013 Simon Guinot <simon.guinot@sequanux.org> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <asm/arch/gpio.h> +#include "cpld-gpio-bus.h" + +static void cpld_gpio_bus_set_addr(struct cpld_gpio_bus *bus, unsigned addr) +{ + int pin; + + for (pin = 0; pin < bus->num_addr; pin++) + kw_gpio_set_value(bus->addr[pin], (addr >> pin) & 1); +} + +static void cpld_gpio_bus_set_data(struct cpld_gpio_bus *bus, unsigned data) +{ + int pin; + + for (pin = 0; pin < bus->num_data; pin++) + kw_gpio_set_value(bus->data[pin], (data >> pin) & 1); +} + +static void cpld_gpio_bus_enable_select(struct cpld_gpio_bus *bus) +{ + /* The transfer is enabled on the raising edge. */ + kw_gpio_set_value(bus->enable, 0); + kw_gpio_set_value(bus->enable, 1); +} + +void cpld_gpio_bus_write(struct cpld_gpio_bus *bus, + unsigned addr, unsigned value) +{ + cpld_gpio_bus_set_addr(bus, addr); + cpld_gpio_bus_set_data(bus, value); + cpld_gpio_bus_enable_select(bus); +} diff --git a/board/LaCie/common/cpld-gpio-bus.h b/board/LaCie/common/cpld-gpio-bus.h new file mode 100644 index 0000000000..e9e9b96041 --- /dev/null +++ b/board/LaCie/common/cpld-gpio-bus.h @@ -0,0 +1,24 @@ +/* + * Copyright (C) 2013 Simon Guinot <simon.guinot@sequanux.org> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#ifndef _LACIE_CPLD_GPI0_BUS_H +#define _LACIE_CPLD_GPI0_BUS_H + +struct cpld_gpio_bus { + unsigned *addr; + unsigned num_addr; + unsigned *data; + unsigned num_data; + unsigned enable; +}; + +void cpld_gpio_bus_write(struct cpld_gpio_bus *cpld_gpio_bus, + unsigned addr, unsigned value); + +#endif /* _LACIE_CPLD_GPI0_BUS_H */ diff --git a/board/LaCie/net2big_v2/Makefile b/board/LaCie/net2big_v2/Makefile index fbae48ef24..9a6dfb619b 100644 --- a/board/LaCie/net2big_v2/Makefile +++ b/board/LaCie/net2big_v2/Makefile @@ -28,6 +28,9 @@ endif LIB = $(obj)lib$(BOARD).o COBJS := $(BOARD).o ../common/common.o +ifneq ($(and $(CONFIG_KIRKWOOD_GPIO),$(CONFIG_NET2BIG_V2)),) +COBJS += ../common/cpld-gpio-bus.o +endif SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) diff --git a/board/LaCie/net2big_v2/net2big_v2.c b/board/LaCie/net2big_v2/net2big_v2.c index e524f3511d..b133f7cb3b 100644 --- a/board/LaCie/net2big_v2/net2big_v2.c +++ b/board/LaCie/net2big_v2/net2big_v2.c @@ -22,6 +22,7 @@ #include <common.h> #include <command.h> +#include <i2c.h> #include <asm/arch/cpu.h> #include <asm/arch/kirkwood.h> #include <asm/arch/mpp.h> @@ -29,6 +30,7 @@ #include "net2big_v2.h" #include "../common/common.h" +#include "../common/cpld-gpio-bus.h" DECLARE_GLOBAL_DATA_PTR; @@ -60,18 +62,18 @@ int board_early_init_f(void) MPP24_GPIO, /* USB mode select */ MPP26_GPIO, /* USB device vbus */ MPP28_GPIO, /* USB enable host vbus */ - MPP29_GPIO, /* GPIO extension ALE */ + MPP29_GPIO, /* CPLD GPIO bus ALE */ MPP34_GPIO, /* Rear Push button 0=on 1=off */ MPP35_GPIO, /* Inhibit switch power-off */ MPP36_GPIO, /* SATA HDD1 presence */ MPP37_GPIO, /* SATA HDD2 presence */ MPP40_GPIO, /* eSATA presence */ - MPP44_GPIO, /* GPIO extension (data 0) */ - MPP45_GPIO, /* GPIO extension (data 1) */ - MPP46_GPIO, /* GPIO extension (data 2) */ - MPP47_GPIO, /* GPIO extension (addr 0) */ - MPP48_GPIO, /* GPIO extension (addr 1) */ - MPP49_GPIO, /* GPIO extension (addr 2) */ + MPP44_GPIO, /* CPLD GPIO bus (data 0) */ + MPP45_GPIO, /* CPLD GPIO bus (data 1) */ + MPP46_GPIO, /* CPLD GPIO bus (data 2) */ + MPP47_GPIO, /* CPLD GPIO bus (addr 0) */ + MPP48_GPIO, /* CPLD GPIO bus (addr 1) */ + MPP49_GPIO, /* CPLD GPIO bus (addr 2) */ 0 }; @@ -92,8 +94,142 @@ int board_init(void) } #if defined(CONFIG_MISC_INIT_R) + +#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_G762_ADDR) +/* + * Start I2C fan (GMT G762 controller) + */ +static void init_fan(void) +{ + u8 data; + + i2c_set_bus_num(0); + + /* Enable open-loop and PWM modes */ + data = 0x20; + if (i2c_write(CONFIG_SYS_I2C_G762_ADDR, + G762_REG_FAN_CMD1, 1, &data, 1) != 0) + goto err; + data = 0; + if (i2c_write(CONFIG_SYS_I2C_G762_ADDR, + G762_REG_SET_CNT, 1, &data, 1) != 0) + goto err; + /* + * RPM to PWM (set_out register) fan speed conversion array: + * 0 0x00 + * 1500 0x04 + * 2800 0x08 + * 3400 0x0C + * 3700 0x10 + * 4400 0x20 + * 4700 0x30 + * 4800 0x50 + * 5200 0x80 + * 5400 0xC0 + * 5500 0xFF + * + * Start fan at low speed (2800 RPM): + */ + data = 0x08; + if (i2c_write(CONFIG_SYS_I2C_G762_ADDR, + G762_REG_SET_OUT, 1, &data, 1) != 0) + goto err; + + return; +err: + printf("Error: failed to start I2C fan @%02x\n", + CONFIG_SYS_I2C_G762_ADDR); +} +#else +static void init_fan(void) {} +#endif /* CONFIG_CMD_I2C && CONFIG_SYS_I2C_G762_ADDR */ + +#if defined(CONFIG_NET2BIG_V2) && defined(CONFIG_KIRKWOOD_GPIO) +/* + * CPLD GPIO bus: + * + * - address register : bit [0-2] -> GPIO [47-49] + * - data register : bit [0-2] -> GPIO [44-46] + * - enable register : GPIO 29 + */ +static unsigned cpld_gpio_bus_addr[] = { 47, 48, 49 }; +static unsigned cpld_gpio_bus_data[] = { 44, 45, 46 }; + +static struct cpld_gpio_bus cpld_gpio_bus = { + .addr = cpld_gpio_bus_addr, + .num_addr = ARRAY_SIZE(cpld_gpio_bus_addr), + .data = cpld_gpio_bus_data, + .num_data = ARRAY_SIZE(cpld_gpio_bus_data), + .enable = 29, +}; + +/* + * LEDs configuration: + * + * The LEDs are controlled by a CPLD and can be configured through + * the CPLD GPIO bus. + * + * Address register selection: + * + * addr | register + * ---------------------------- + * 0 | front LED + * 1 | front LED brightness + * 2 | SATA LED brightness + * 3 | SATA0 LED + * 4 | SATA1 LED + * 5 | SATA2 LED + * 6 | SATA3 LED + * 7 | SATA4 LED + * + * Data register configuration: + * + * data | LED brightness + * ------------------------------------------------- + * 0 | min (off) + * - | - + * 7 | max + * + * data | front LED mode + * ------------------------------------------------- + * 0 | fix off + * 1 | fix blue on + * 2 | fix red on + * 3 | blink blue on=1 sec and blue off=1 sec + * 4 | blink red on=1 sec and red off=1 sec + * 5 | blink blue on=2.5 sec and red on=0.5 sec + * 6 | blink blue on=1 sec and red on=1 sec + * 7 | blink blue on=0.5 sec and blue off=2.5 sec + * + * data | SATA LED mode + * ------------------------------------------------- + * 0 | fix off + * 1 | SATA activity blink + * 2 | fix red on + * 3 | blink blue on=1 sec and blue off=1 sec + * 4 | blink red on=1 sec and red off=1 sec + * 5 | blink blue on=2.5 sec and red on=0.5 sec + * 6 | blink blue on=1 sec and red on=1 sec + * 7 | fix blue on + */ +static void init_leds(void) +{ + /* Enable the front blue LED */ + cpld_gpio_bus_write(&cpld_gpio_bus, 0, 1); + cpld_gpio_bus_write(&cpld_gpio_bus, 1, 3); + + /* Configure SATA LEDs to blink in relation with the SATA activity */ + cpld_gpio_bus_write(&cpld_gpio_bus, 3, 1); + cpld_gpio_bus_write(&cpld_gpio_bus, 4, 1); + cpld_gpio_bus_write(&cpld_gpio_bus, 2, 3); +} +#else +static void init_leds(void) {} +#endif /* CONFIG_NET2BIG_V2 && CONFIG_KIRKWOOD_GPIO */ + int misc_init_r(void) { + init_fan(); #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) if (!getenv("ethaddr")) { uchar mac[6]; @@ -101,9 +237,11 @@ int misc_init_r(void) eth_setenv_enetaddr("ethaddr", mac); } #endif + init_leds(); + return 0; } -#endif +#endif /* CONFIG_MISC_INIT_R */ #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R) /* Configure and initialize PHY */ diff --git a/board/LaCie/net2big_v2/net2big_v2.h b/board/LaCie/net2big_v2/net2big_v2.h index f9778f4f0c..83537d6b9a 100644 --- a/board/LaCie/net2big_v2/net2big_v2.h +++ b/board/LaCie/net2big_v2/net2big_v2.h @@ -32,4 +32,9 @@ /* Buttons */ #define NET2BIG_V2_GPIO_PUSH_BUTTON 34 +/* GMT G762 registers (I2C fan controller) */ +#define G762_REG_SET_CNT 0x00 +#define G762_REG_SET_OUT 0x03 +#define G762_REG_FAN_CMD1 0x04 + #endif /* NET2BIG_V2_H */ diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds index ef4a25bc3c..74aec5fbcc 100644 --- a/board/actux1/u-boot.lds +++ b/board/actux1/u-boot.lds @@ -30,6 +30,7 @@ SECTIONS . = ALIGN (4); .text : { + *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) net/libnet.o(.text*) board/actux1/libactux1.o(.text*) @@ -62,17 +63,23 @@ SECTIONS . = ALIGN (4); - __image_copy_end = .; + .image_copy_end : + { + *(.__image_copy_end) + } + + .rel_dyn_start : + { + *(.__rel_dyn_start) + } .rel.dyn : { - __rel_dyn_start = .; *(.rel*) - __rel_dyn_end = .; } - .dynsym : { - __dynsym_start = .; - *(.dynsym) + .rel_dyn_end : + { + *(.__rel_dyn_end) } _end = .; @@ -96,6 +103,7 @@ SECTIONS KEEP(*(.__bss_end)); } + /DISCARD/ : { *(.dynsym) } /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynamic*) } /DISCARD/ : { *(.plt*) } diff --git a/board/actux2/u-boot.lds b/board/actux2/u-boot.lds index 00ad8b71cd..c276501bd7 100644 --- a/board/actux2/u-boot.lds +++ b/board/actux2/u-boot.lds @@ -30,6 +30,7 @@ SECTIONS . = ALIGN (4); .text : { + *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) net/libnet.o(.text*) board/actux2/libactux2.o(.text*) @@ -62,17 +63,23 @@ SECTIONS . = ALIGN (4); - __image_copy_end = .; + .image_copy_end : + { + *(.__image_copy_end) + } + + .rel_dyn_start : + { + *(.__rel_dyn_start) + } .rel.dyn : { - __rel_dyn_start = .; *(.rel*) - __rel_dyn_end = .; } - .dynsym : { - __dynsym_start = .; - *(.dynsym) + .rel_dyn_end : + { + *(.__rel_dyn_end) } _end = .; @@ -96,6 +103,7 @@ SECTIONS KEEP(*(.__bss_end)); } + /DISCARD/ : { *(.dynsym) } /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynamic*) } /DISCARD/ : { *(.plt*) } diff --git a/board/actux3/u-boot.lds b/board/actux3/u-boot.lds index 44b990ee7f..5610644d79 100644 --- a/board/actux3/u-boot.lds +++ b/board/actux3/u-boot.lds @@ -30,6 +30,7 @@ SECTIONS . = ALIGN (4); .text : { + *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) net/libnet.o(.text*) board/actux3/libactux3.o(.text*) @@ -62,17 +63,23 @@ SECTIONS . = ALIGN (4); - __image_copy_end = .; + .image_copy_end : + { + *(.__image_copy_end) + } + + .rel_dyn_start : + { + *(.__rel_dyn_start) + } .rel.dyn : { - __rel_dyn_start = .; *(.rel*) - __rel_dyn_end = .; } - .dynsym : { - __dynsym_start = .; - *(.dynsym) + .rel_dyn_end : + { + *(.__rel_dyn_end) } _end = .; @@ -96,6 +103,7 @@ SECTIONS KEEP(*(.__bss_end)); } + /DISCARD/ : { *(.dynsym) } /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynamic*) } /DISCARD/ : { *(.plt*) } diff --git a/board/ait/cam_enc_4xx/u-boot-spl.lds b/board/ait/cam_enc_4xx/u-boot-spl.lds index 1daa1b3b90..39726854cd 100644 --- a/board/ait/cam_enc_4xx/u-boot-spl.lds +++ b/board/ait/cam_enc_4xx/u-boot-spl.lds @@ -54,11 +54,6 @@ SECTIONS __rel_dyn_end = .; } >.sram - .dynsym : { - __dynsym_start = .; - *(.dynsym) - } >.sram - .bss : { . = ALIGN(4); diff --git a/board/atmel/at91sam9n12ek/at91sam9n12ek.c b/board/atmel/at91sam9n12ek/at91sam9n12ek.c index 8752794c84..3013a42a2e 100644 --- a/board/atmel/at91sam9n12ek/at91sam9n12ek.c +++ b/board/atmel/at91sam9n12ek/at91sam9n12ek.c @@ -33,6 +33,7 @@ #include <lcd.h> #include <atmel_hlcdc.h> #include <atmel_mci.h> +#include <netdev.h> #ifdef CONFIG_LCD_INFO #include <nand.h> @@ -190,6 +191,30 @@ int board_mmc_init(bd_t *bd) } #endif +#ifdef CONFIG_KS8851_MLL +void at91sam9n12ek_ks8851_hw_init(void) +{ + struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC; + + writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) | + AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0), + &smc->cs[2].setup); + writel(AT91_SMC_PULSE_NWE(7) | AT91_SMC_PULSE_NCS_WR(7) | + AT91_SMC_PULSE_NRD(7) | AT91_SMC_PULSE_NCS_RD(7), + &smc->cs[2].pulse); + writel(AT91_SMC_CYCLE_NWE(9) | AT91_SMC_CYCLE_NRD(9), + &smc->cs[2].cycle); + writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE | + AT91_SMC_MODE_EXNW_DISABLE | + AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 | + AT91_SMC_MODE_TDF_CYCLE(1), + &smc->cs[2].mode); + + /* Configure NCS2 PIN */ + at91_set_b_periph(AT91_PIO_PORTD, 19, 0); +} +#endif + int board_early_init_f(void) { /* Enable clocks for all PIOs */ @@ -217,9 +242,20 @@ int board_init(void) at91_lcd_hw_init(); #endif +#ifdef CONFIG_KS8851_MLL + at91sam9n12ek_ks8851_hw_init(); +#endif + return 0; } +#ifdef CONFIG_KS8851_MLL +int board_eth_init(bd_t *bis) +{ + return ks8851_mll_initialize(0, CONFIG_KS8851_MLL_BASEADDR); +} +#endif + int dram_init(void) { gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, diff --git a/board/davinci/da8xxevm/u-boot-spl-da850evm.lds b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds index b1b8701811..6fa450909f 100644 --- a/board/davinci/da8xxevm/u-boot-spl-da850evm.lds +++ b/board/davinci/da8xxevm/u-boot-spl-da850evm.lds @@ -55,11 +55,6 @@ SECTIONS __rel_dyn_end = .; } >.sram - .dynsym : { - __dynsym_start = .; - *(.dynsym) - } >.sram - .bss : { . = ALIGN(4); diff --git a/board/davinci/da8xxevm/u-boot-spl-hawk.lds b/board/davinci/da8xxevm/u-boot-spl-hawk.lds index 596a9e08ea..b452f2078b 100644 --- a/board/davinci/da8xxevm/u-boot-spl-hawk.lds +++ b/board/davinci/da8xxevm/u-boot-spl-hawk.lds @@ -61,7 +61,6 @@ SECTIONS __image_copy_end = .; __rel_dyn_start = .; __rel_dyn_end = .; - __dynsym_start = .; __got_start = .; . = ALIGN(4); diff --git a/board/dvlhost/u-boot.lds b/board/dvlhost/u-boot.lds index 6d4b1875c5..f359112323 100644 --- a/board/dvlhost/u-boot.lds +++ b/board/dvlhost/u-boot.lds @@ -30,6 +30,7 @@ SECTIONS . = ALIGN (4); .text : { + *(.__image_copy_start) arch/arm/cpu/ixp/start.o(.text*) net/libnet.o(.text*) board/dvlhost/libdvlhost.o(.text*) @@ -62,17 +63,23 @@ SECTIONS . = ALIGN (4); - __image_copy_end = .; + .image_copy_end : + { + *(.__image_copy_end) + } + + .rel_dyn_start : + { + *(.__rel_dyn_start) + } .rel.dyn : { - __rel_dyn_start = .; *(.rel*) - __rel_dyn_end = .; } - .dynsym : { - __dynsym_start = .; - *(.dynsym) + .rel_dyn_end : + { + *(.__rel_dyn_end) } _end = .; @@ -96,6 +103,7 @@ SECTIONS KEEP(*(.__bss_end)); } + /DISCARD/ : { *(.dynsym) } /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynamic*) } /DISCARD/ : { *(.plt*) } diff --git a/board/eltec/elppc/misc.c b/board/eltec/elppc/misc.c index 89f1b1d355..4c3656e24d 100644 --- a/board/eltec/elppc/misc.c +++ b/board/eltec/elppc/misc.c @@ -207,9 +207,14 @@ int misc_init_r (void) buf[4] = eerev.etheraddr[5]; buf[5] = eerev.etheraddr[4]; - *(unsigned short *) &buf[20] = 0x48B2; - *(unsigned short *) &buf[22] = 0x0004; - *(unsigned short *) &buf[24] = 0x1433; + buf[20] = 0x48; + buf[21] = 0xB2; + + buf[22] = 0x00; + buf[23] = 0x04; + + buf[24] = 0x14; + buf[25] = 0x33; printf ("\nSRom: Writing i82559 info ........ "); if (eepro100_srom_store ((unsigned short *) buf) == -1) diff --git a/board/freescale/b4860qds/tlb.c b/board/freescale/b4860qds/tlb.c index 29cc41bfaf..1416f98dc6 100644 --- a/board/freescale/b4860qds/tlb.c +++ b/board/freescale/b4860qds/tlb.c @@ -52,6 +52,15 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 0, BOOKE_PAGESZ_1M, 1), +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) + /* + * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the + * space is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), #else SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -137,6 +146,16 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 16, BOOKE_PAGESZ_256M, 1), #endif +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE + /* + * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for + * fetching ucode and ENV from master + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 17, BOOKE_PAGESZ_1M, 1), +#endif }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/bsc9131rdb/Makefile b/board/freescale/bsc9131rdb/Makefile index 6f4cb268f1..2e829ad2e2 100644 --- a/board/freescale/bsc9131rdb/Makefile +++ b/board/freescale/bsc9131rdb/Makefile @@ -24,12 +24,28 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL + +COBJS-y += spl_minimal.o tlb.o law.o + +else + COBJS-y += $(BOARD).o COBJS-y += ddr.o COBJS-y += law.o COBJS-y += tlb.o #COBJS-y += bsc9131rdb_mux.o +endif + SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) SOBJS := $(addprefix $(obj),$(SOBJS)) diff --git a/board/freescale/bsc9131rdb/README b/board/freescale/bsc9131rdb/README index 065faa378d..4902b98ba1 100644 --- a/board/freescale/bsc9131rdb/README +++ b/board/freescale/bsc9131rdb/README @@ -89,10 +89,14 @@ NAND boot Building U-boot -------------- To build the u-boot for BSC9131RDB: -1. NAND Flash +1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default) make BSC9131RDB_NAND -2. SPI Flash +2. NAND Flash with sysclk 100MHz(J16 on RDB open) + make BSC9131RDB_NAND_SYSCLK100 +3. SPI Flash with sysclk 66MHz(J16 on RDB closed, default) make BSC9131RDB_SPIFLASH +4. SPI Flash with sysclk 100MHz(J16 on RDB open) + make BSC9131RDB_SPIFLASH_SYSCLK100 Memory map ----------- @@ -107,6 +111,16 @@ Memory map 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M +DDR Memory map +--------------- + 0x0000_0000 0x36FF_FFFF Memory passed onto Linux + 0x3700_0000 0x37FF_FFFF PowerPC-DSP shared control area + 0x3800_0000 0x4FFF_FFFF DSP Private area + + Out of 880M, passed onto Linux, 1hugetlb page of 256M is reserved for + data communcation between PowerPC and DSP core. + Rest is PowerPC private area. + Flashing Images --------------- To place a new u-boot image in the NAND flash and then boot diff --git a/board/freescale/bsc9131rdb/law.c b/board/freescale/bsc9131rdb/law.c index 201c147079..0432780f94 100644 --- a/board/freescale/bsc9131rdb/law.c +++ b/board/freescale/bsc9131rdb/law.c @@ -26,6 +26,10 @@ struct law_entry law_table[] = { SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), + SET_LAW(CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS, LAW_SIZE_1M, + LAW_TRGT_IF_DSP_CCSR), + SET_LAW(CONFIG_SYS_FSL_DSP_M2_RAM_ADDR, LAW_SIZE_16M, + LAW_TRGT_IF_OCN_DSP), }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/bsc9131rdb/spl_minimal.c b/board/freescale/bsc9131rdb/spl_minimal.c new file mode 100644 index 0000000000..301115e5e6 --- /dev/null +++ b/board/freescale/bsc9131rdb/spl_minimal.c @@ -0,0 +1,118 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include <ns16550.h> +#include <asm/io.h> +#include <nand.h> +#include <linux/compiler.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Fixed sdram init -- doesn't use serial presence detect. + */ +static void sdram_init(void) +{ + ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR; + + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); +#if CONFIG_CHIP_SELECTS_PER_CTRL > 1 + __raw_writel(CONFIG_SYS_DDR_CS1_BNDS, &ddr->cs1_bnds); + __raw_writel(CONFIG_SYS_DDR_CS1_CONFIG, &ddr->cs1_config); +#endif + __raw_writel(CONFIG_SYS_DDR_TIMING_3_800, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_800, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_800, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_800, &ddr->timing_cfg_2); + + __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_800, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_800, &ddr->sdram_mode_2); + + __raw_writel(CONFIG_SYS_DDR_INTERVAL_800, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_800, &ddr->sdram_clk_cntl); + + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_800, &ddr->ddr_wrlvl_cntl); + __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); + + /* Set, but do not enable the memory */ + __raw_writel(CONFIG_SYS_DDR_CONTROL & ~SDRAM_CFG_MEM_EN, &ddr->sdram_cfg); + + asm volatile("sync;isync"); + udelay(500); + + /* Let the controller go */ + out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); + + set_next_law(CONFIG_SYS_NAND_DDR_LAW, LAW_SIZE_1G, LAW_TRGT_IF_DDR_1); +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* Initialize the DDR3 */ + sdram_init(); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/freescale/bsc9131rdb/tlb.c b/board/freescale/bsc9131rdb/tlb.c index 5b68f4af3c..c05a556a3d 100644 --- a/board/freescale/bsc9131rdb/tlb.c +++ b/board/freescale/bsc9131rdb/tlb.c @@ -44,15 +44,26 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 1 */ /* *I*** - Covers boot page */ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#ifdef CONFIG_SPL_NAND_MINIMAL + SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_4K, 1), +#endif /* *I*G* - CCSRBAR (PA) */ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 1, BOOKE_PAGESZ_1M, 1), -#if defined(CONFIG_SYS_RAMBOOT) + /* CCSRBAR (DSP) */ + SET_TLB_ENTRY(1, CONFIG_SYS_FSL_DSP_CCSRBAR, + CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 2, BOOKE_PAGESZ_1M, 1), + +#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL) SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 8, BOOKE_PAGESZ_1G, 1), diff --git a/board/freescale/bsc9132qds/Makefile b/board/freescale/bsc9132qds/Makefile index 267400becb..72b19174bf 100644 --- a/board/freescale/bsc9132qds/Makefile +++ b/board/freescale/bsc9132qds/Makefile @@ -24,11 +24,28 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL + +COBJS-y += spl_minimal.o tlb.o law.o + +else + + COBJS-y += $(BOARD).o COBJS-y += ddr.o COBJS-y += law.o COBJS-y += tlb.o +endif + SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) SOBJS := $(addprefix $(obj),$(SOBJS)) diff --git a/board/freescale/bsc9132qds/bsc9132qds.c b/board/freescale/bsc9132qds/bsc9132qds.c index 6e1b55816f..ddc9d0a16a 100644 --- a/board/freescale/bsc9132qds/bsc9132qds.c +++ b/board/freescale/bsc9132qds/bsc9132qds.c @@ -258,7 +258,7 @@ int misc_init_r(void) u8 val; ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); u32 porbmsr = in_be32(&gur->porbmsr); - u32 romloc = (porbmsr >> MPC85XX_PORBMSR_ROMLOC_SHIFT) & 0xf; + u32 romloc = (porbmsr >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf; /*Configure 1588 clock-in source from RF Card*/ val = QIXIS_READ_I2C(brdcfg[5]); @@ -360,7 +360,7 @@ void ft_board_setup(void *blob, bd_t *bd) ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); u32 porbmsr = in_be32(&gur->porbmsr); - u32 romloc = (porbmsr >> MPC85XX_PORBMSR_ROMLOC_SHIFT) & 0xf; + u32 romloc = (porbmsr >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf; if (!(hwconfig("uart2") && hwconfig("usb1"))) { /* If uart2 is there in hwconfig remove usb node from diff --git a/board/freescale/bsc9132qds/law.c b/board/freescale/bsc9132qds/law.c index dc2365851b..b4bce99d3d 100644 --- a/board/freescale/bsc9132qds/law.c +++ b/board/freescale/bsc9132qds/law.c @@ -25,11 +25,13 @@ #include <asm/mmu.h> struct law_entry law_table[] = { -#ifndef CONFIG_SYS_NO_FLASH SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_128M, LAW_TRGT_IF_IFC), -#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_IFC), +#endif +#ifdef CONFIG_SYS_FPGA_BASE_PHYS SET_LAW(CONFIG_SYS_FPGA_BASE_PHYS, LAW_SIZE_128K, LAW_TRGT_IF_IFC), +#endif }; int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/bsc9132qds/spl_minimal.c b/board/freescale/bsc9132qds/spl_minimal.c new file mode 100644 index 0000000000..62dee52b17 --- /dev/null +++ b/board/freescale/bsc9132qds/spl_minimal.c @@ -0,0 +1,130 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ + +#include <common.h> +#include <ns16550.h> +#include <asm/io.h> +#include <nand.h> +#include <linux/compiler.h> +#include <asm/fsl_law.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; + +static void sdram_init(void) +{ + ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR; +#if CONFIG_DDR_CLK_FREQ == 100000000 + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); + __raw_writel(CONFIG_SYS_DDR_CONTROL_800 | SDRAM_CFG_32_BE, &ddr->sdram_cfg); + __raw_writel(CONFIG_SYS_DDR_CONTROL_2_800, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + + __raw_writel(CONFIG_SYS_DDR_TIMING_3_800, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_800, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_800, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_800, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_800, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_800, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL_800, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_800, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_800, &ddr->ddr_wrlvl_cntl); + + __raw_writel(CONFIG_SYS_DDR_TIMING_4_800, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5_800, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); +#elif CONFIG_DDR_CLK_FREQ == 133000000 + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); + __raw_writel(CONFIG_SYS_DDR_CONTROL_1333 | SDRAM_CFG_32_BE, &ddr->sdram_cfg); + __raw_writel(CONFIG_SYS_DDR_CONTROL_2_1333, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + + __raw_writel(CONFIG_SYS_DDR_TIMING_3_1333, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_1333, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_1333, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_1333, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_1333, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_1333, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL_1333, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_1333, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_1333, &ddr->ddr_wrlvl_cntl); + + __raw_writel(CONFIG_SYS_DDR_TIMING_4_1333, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5_1333, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); +#else + puts("Not a valid DDR Freq Found! Please Reset\n"); +#endif + asm volatile("sync;isync"); + udelay(500); + + /* Let the controller go */ + out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); + + set_next_law(CONFIG_SYS_NAND_DDR_LAW, LAW_SIZE_1G, LAW_TRGT_IF_DDR_1); +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* Initialize the DDR3 */ + sdram_init(); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/freescale/bsc9132qds/tlb.c b/board/freescale/bsc9132qds/tlb.c index 0e4545fb12..0ec9a851ab 100644 --- a/board/freescale/bsc9132qds/tlb.c +++ b/board/freescale/bsc9132qds/tlb.c @@ -44,14 +44,20 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 1 */ /* *I*** - Covers boot page */ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#ifdef CONFIG_SPL_NAND_MINIMAL + SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_4K, 1), +#endif /* *I*G* - CCSRBAR (PA) */ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 1, BOOKE_PAGESZ_1M, 1), +#ifndef CONFIG_SPL_BUILD SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 3, BOOKE_PAGESZ_64M, 1), @@ -61,12 +67,6 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, 0, 4, BOOKE_PAGESZ_64M, 1), -#if defined(CONFIG_SYS_RAMBOOT) - SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, - MAS3_SX|MAS3_SW|MAS3_SR, 0, - 0, 8, BOOKE_PAGESZ_1G, 1), -#endif - #ifdef CONFIG_PCI /* *I*G* - PCI */ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS, @@ -78,15 +78,26 @@ struct fsl_e_tlb_entry tlb_table[] = { MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 7, BOOKE_PAGESZ_64K, 1), #endif +#endif + +#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL) + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 8, BOOKE_PAGESZ_1G, 1), +#endif +#ifdef CONFIG_SYS_FPGA_BASE /* *I*G - Board FPGA */ SET_TLB_ENTRY(1, CONFIG_SYS_FPGA_BASE, CONFIG_SYS_FPGA_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 9, BOOKE_PAGESZ_256K, 1), +#endif +#ifdef CONFIG_SYS_NAND_BASE_PHYS SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 5, BOOKE_PAGESZ_1M, 1), +#endif }; int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile index 72bb56cac4..37236d072b 100644 --- a/board/freescale/common/Makefile +++ b/board/freescale/common/Makefile @@ -29,6 +29,15 @@ endif LIB = $(obj)libfreescale.o +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifndef MINIMAL COBJS-$(CONFIG_FSL_CADMUS) += cadmus.o COBJS-$(CONFIG_FSL_VIA) += cds_via.o COBJS-$(CONFIG_FMAN_ENET) += fman.o @@ -68,6 +77,7 @@ SUBLIB-$(CONFIG_P3041DS) += p_corenet/libp_corenet.o SUBLIB-$(CONFIG_P4080DS) += p_corenet/libp_corenet.o SUBLIB-$(CONFIG_P5020DS) += p_corenet/libp_corenet.o SUBLIB-$(CONFIG_P5040DS) += p_corenet/libp_corenet.o +endif SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) diff --git a/board/freescale/common/pixis.c b/board/freescale/common/pixis.c index 8d07061c36..fbb709de14 100644 --- a/board/freescale/common/pixis.c +++ b/board/freescale/common/pixis.c @@ -480,6 +480,7 @@ static int pixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const ar || unknown_param) { #ifdef CONFIG_SYS_LONGHELP puts(cmdtp->help); + putc('\n'); #endif return 1; } @@ -512,6 +513,7 @@ static int pixis_reset_cmd(cmd_tbl_t *cmdtp, int flag, int argc, char * const ar && set_px_mpxpll(mpxpll))) { #ifdef CONFIG_SYS_LONGHELP puts(cmdtp->help); + putc('\n'); #endif return 1; } diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds index 4969960001..963d29f2dc 100644 --- a/board/freescale/mx31ads/u-boot.lds +++ b/board/freescale/mx31ads/u-boot.lds @@ -34,6 +34,7 @@ SECTIONS . = ALIGN(4); .text : { + *(.__image_copy_start) /* WARNING - the following is hand-optimized to fit within */ /* the sector layout of our flash chips! XXX FIXME XXX */ @@ -65,17 +66,23 @@ SECTIONS . = ALIGN(4); - __image_copy_end = .; + .image_copy_end : + { + *(.__image_copy_end) + } + + .rel_dyn_start : + { + *(.__rel_dyn_start) + } .rel.dyn : { - __rel_dyn_start = .; *(.rel*) - __rel_dyn_end = .; } - .dynsym : { - __dynsym_start = .; - *(.dynsym) + .rel_dyn_end : + { + *(.__rel_dyn_end) } _end = .; @@ -100,6 +107,7 @@ SECTIONS } /DISCARD/ : { *(.bss*) } + /DISCARD/ : { *(.dynsym) } /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynsym*) } /DISCARD/ : { *(.dynamic*) } diff --git a/board/freescale/p1010rdb/Makefile b/board/freescale/p1010rdb/Makefile index 4c705b627e..e6563be098 100644 --- a/board/freescale/p1010rdb/Makefile +++ b/board/freescale/p1010rdb/Makefile @@ -24,11 +24,27 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o +MINIMAL= + +ifdef CONFIG_SPL_BUILD +ifdef CONFIG_SPL_INIT_MINIMAL +MINIMAL=y +endif +endif + +ifdef MINIMAL + +COBJS-y += spl_minimal.o tlb.o law.o + +else + COBJS-y += $(BOARD).o COBJS-y += ddr.o COBJS-y += law.o COBJS-y += tlb.o +endif + SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) SOBJS := $(addprefix $(obj),$(SOBJS)) diff --git a/board/freescale/p1010rdb/spl_minimal.c b/board/freescale/p1010rdb/spl_minimal.c new file mode 100644 index 0000000000..c909e0ee31 --- /dev/null +++ b/board/freescale/p1010rdb/spl_minimal.c @@ -0,0 +1,143 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + * + */ +#include <common.h> +#include <mpc85xx.h> +#include <asm/io.h> +#include <ns16550.h> +#include <nand.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_law.h> +#include <asm/global_data.h> + +DECLARE_GLOBAL_DATA_PTR; + + +void sdram_init(void) +{ + ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC8xxx_DDR_ADDR; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + u32 ddr_ratio; + unsigned long ddr_freq_mhz; + + ddr_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_DDR_RATIO; + ddr_ratio = ddr_ratio >> MPC85xx_PORPLLSR_DDR_RATIO_SHIFT; + ddr_freq_mhz = (CONFIG_SYS_CLK_FREQ * ddr_ratio) / 0x1000000; + + /* mask off E bit */ + u32 svr = SVR_SOC_VER(mfspr(SPRN_SVR)); + + __raw_writel(CONFIG_SYS_DDR_CONTROL | SDRAM_CFG_32_BE, &ddr->sdram_cfg); + __raw_writel(CONFIG_SYS_DDR_CS0_BNDS, &ddr->cs0_bnds); + __raw_writel(CONFIG_SYS_DDR_CS0_CONFIG, &ddr->cs0_config); + __raw_writel(CONFIG_SYS_DDR_CONTROL_2, &ddr->sdram_cfg_2); + __raw_writel(CONFIG_SYS_DDR_DATA_INIT, &ddr->sdram_data_init); + + if (ddr_freq_mhz < 700) { + __raw_writel(CONFIG_SYS_DDR_TIMING_3_667, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_667, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_667, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_667, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_667, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_667, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL_667, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_667, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_667, &ddr->ddr_wrlvl_cntl); + } else { + __raw_writel(CONFIG_SYS_DDR_TIMING_3_800, &ddr->timing_cfg_3); + __raw_writel(CONFIG_SYS_DDR_TIMING_0_800, &ddr->timing_cfg_0); + __raw_writel(CONFIG_SYS_DDR_TIMING_1_800, &ddr->timing_cfg_1); + __raw_writel(CONFIG_SYS_DDR_TIMING_2_800, &ddr->timing_cfg_2); + __raw_writel(CONFIG_SYS_DDR_MODE_1_800, &ddr->sdram_mode); + __raw_writel(CONFIG_SYS_DDR_MODE_2_800, &ddr->sdram_mode_2); + __raw_writel(CONFIG_SYS_DDR_INTERVAL_800, &ddr->sdram_interval); + __raw_writel(CONFIG_SYS_DDR_CLK_CTRL_800, &ddr->sdram_clk_cntl); + __raw_writel(CONFIG_SYS_DDR_WRLVL_CONTROL_800, &ddr->ddr_wrlvl_cntl); + } + + __raw_writel(CONFIG_SYS_DDR_TIMING_4, &ddr->timing_cfg_4); + __raw_writel(CONFIG_SYS_DDR_TIMING_5, &ddr->timing_cfg_5); + __raw_writel(CONFIG_SYS_DDR_ZQ_CONTROL, &ddr->ddr_zq_cntl); + + /* P1014 and it's derivatives support max 16bit DDR width */ + if (svr == SVR_P1014) { + __raw_writel(ddr->sdram_cfg & ~SDRAM_CFG_DBW_MASK, &ddr->sdram_cfg); + __raw_writel(ddr->sdram_cfg | SDRAM_CFG_16_BE, &ddr->sdram_cfg); + /* For CS0_BNDS we divide the start and end address by 2, so we can just + * shift the entire register to achieve the desired result and the mask + * the value so we don't write reserved fields */ + __raw_writel((CONFIG_SYS_DDR_CS0_BNDS >> 1) & 0x0fff0fff, &ddr->cs0_bnds); + } + + asm volatile("sync;isync"); + udelay(500); + + /* Let the controller go */ + out_be32(&ddr->sdram_cfg, in_be32(&ddr->sdram_cfg) | SDRAM_CFG_MEM_EN); + + set_next_law(CONFIG_SYS_NAND_DDR_LAW, LAW_SIZE_1G, LAW_TRGT_IF_DDR_1); +} + +void board_init_f(ulong bootflag) +{ + u32 plat_ratio; + ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + + /* initialize selected port with appropriate baud rate */ + plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO; + plat_ratio >>= 1; + gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio; + + NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1, + gd->bus_clk / 16 / CONFIG_BAUDRATE); + + puts("\nNAND boot... "); + + /* Initialize the DDR3 */ + sdram_init(); + + /* copy code to RAM and jump to it - this should not return */ + /* NOTE - code has to be copied out of NAND buffer before + * other blocks can be read. + */ + + relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE); +} + +void board_init_r(gd_t *gd, ulong dest_addr) +{ + nand_boot(); +} + +void putc(char c) +{ + if (c == '\n') + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r'); + + NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c); +} + +void puts(const char *str) +{ + while (*str) + putc(*str++); +} diff --git a/board/freescale/p1010rdb/tlb.c b/board/freescale/p1010rdb/tlb.c index 4256bf4e57..078717a5b9 100644 --- a/board/freescale/p1010rdb/tlb.c +++ b/board/freescale/p1010rdb/tlb.c @@ -44,15 +44,20 @@ struct fsl_e_tlb_entry tlb_table[] = { /* TLB 1 */ /* *I*** - Covers boot page */ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, - MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, - 0, 0, BOOKE_PAGESZ_4K, 1), + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 0, BOOKE_PAGESZ_4K, 1), +#ifdef CONFIG_SPL_NAND_MINIMAL + SET_TLB_ENTRY(1, 0xffffe000, 0xffffe000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_4K, 1), +#endif /* *I*G* - CCSRBAR */ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 1, BOOKE_PAGESZ_1M, 1), -#ifndef CONFIG_NAND_SPL +#ifndef CONFIG_SPL_BUILD #ifndef CONFIG_SDCARD SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, MAS3_SX|MAS3_SR, MAS2_W|MAS2_G, @@ -88,7 +93,7 @@ struct fsl_e_tlb_entry tlb_table[] = { 0, 7, BOOKE_PAGESZ_1M, 1), #endif -#if defined(CONFIG_SYS_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL) SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE, MAS3_SX|MAS3_SW|MAS3_SR, 0, 0, 8, BOOKE_PAGESZ_1G, 1) diff --git a/board/freescale/p1023rdb/Makefile b/board/freescale/p1023rdb/Makefile new file mode 100644 index 0000000000..45c4f8b7c1 --- /dev/null +++ b/board/freescale/p1023rdb/Makefile @@ -0,0 +1,33 @@ +# +# Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or modify it +# under the terms of the GNU General Public License as published by the Free +# Software Foundation; either version 2 of the License, or (at your option) +# any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += $(BOARD).o +COBJS-y += ddr.o +COBJS-y += law.o +COBJS-y += tlb.o + +SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS-y)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/p1023rdb/ddr.c b/board/freescale/p1023rdb/ddr.c new file mode 100644 index 0000000000..7ed275ade2 --- /dev/null +++ b/board/freescale/p1023rdb/ddr.c @@ -0,0 +1,105 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/processor.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_ddr_dimm_params.h> +#include <asm/io.h> +#include <asm/fsl_law.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* CONFIG_SYS_DDR_RAW_TIMING */ +/* + * Hynix H5TQ1G83TFR-H9C + */ +dimm_params_t ddr_raw_timing = { + .n_ranks = 1, + .rank_density = 536870912u, + .capacity = 536870912u, + .primary_sdram_width = 32, + .ec_sdram_width = 0, + .registered_dimm = 0, + .mirrored_dimm = 0, + .n_row_addr = 14, + .n_col_addr = 10, + .n_banks_per_sdram_device = 8, + .edc_config = 0, + .burst_lengths_bitmask = 0x0c, + + .tCKmin_X_ps = 1875, + .caslat_X = 0x1e << 4, /* 5,6,7,8 */ + .tAA_ps = 13125, + .tWR_ps = 18000, + .tRCD_ps = 13125, + .tRRD_ps = 7500, + .tRP_ps = 13125, + .tRAS_ps = 37500, + .tRC_ps = 50625, + .tRFC_ps = 160000, + .tWTR_ps = 7500, + .tRTP_ps = 7500, + .refresh_rate_ps = 7800000, + .tFAW_ps = 37500, +}; + +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm, + unsigned int controller_number, + unsigned int dimm_number) +{ + const char dimm_model[] = "Fixed DDR on board"; + + if ((controller_number == 0) && (dimm_number == 0)) { + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t)); + memset(pdimm->mpart, 0, sizeof(pdimm->mpart)); + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1); + } + + return 0; +} + +void fsl_ddr_board_options(memctl_options_t *popts, + dimm_params_t *pdimm, + unsigned int ctrl_num) +{ + int i; + popts->clk_adjust = 6; + popts->cpo_override = 0x1f; + popts->write_data_delay = 2; + popts->half_strength_driver_enable = 1; + /* Write leveling override */ + popts->wrlvl_en = 1; + popts->wrlvl_override = 1; + popts->wrlvl_sample = 0xf; + popts->wrlvl_start = 0x8; + popts->trwt_override = 1; + popts->trwt = 0; + + for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { + popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; + popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; + } +} + diff --git a/board/samsung/smdk5250/tzpc_init.c b/board/freescale/p1023rdb/law.c index c833541fd0..331662cfc6 100644 --- a/board/samsung/smdk5250/tzpc_init.c +++ b/board/freescale/p1023rdb/law.c @@ -1,7 +1,5 @@ /* - * Lowlevel setup for SMDK5250 board based on S5PC520 - * - * Copyright (C) 2012 Samsung Electronics + * Copyright 2013 Freescale Semiconductor, Inc. * * See file CREDITS for list of people who contributed to this * project. @@ -22,27 +20,15 @@ * MA 02111-1307 USA */ -#include <asm/arch/tzpc.h> -#include"setup.h" - -/* Setting TZPC[TrustZone Protection Controller] */ -void tzpc_init(void) -{ - struct exynos_tzpc *tzpc; - unsigned int addr; - - for (addr = TZPC0_BASE; addr <= TZPC9_BASE; addr += TZPC_BASE_OFFSET) { - tzpc = (struct exynos_tzpc *)addr; - - if (addr == TZPC0_BASE) - writel(R0SIZE, &tzpc->r0size); +#include <common.h> +#include <asm/fsl_law.h> +#include <asm/mmu.h> - writel(DECPROTXSET, &tzpc->decprot0set); - writel(DECPROTXSET, &tzpc->decprot1set); +struct law_entry law_table[] = { + SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC), + SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_4M, + LAW_TRGT_IF_DPAA_SWP_SRAM), + SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC), +}; - if (addr != TZPC9_BASE) { - writel(DECPROTXSET, &tzpc->decprot2set); - writel(DECPROTXSET, &tzpc->decprot3set); - } - } -} +int num_law_entries = ARRAY_SIZE(law_table); diff --git a/board/freescale/p1023rdb/p1023rdb.c b/board/freescale/p1023rdb/p1023rdb.c new file mode 100644 index 0000000000..918398bd85 --- /dev/null +++ b/board/freescale/p1023rdb/p1023rdb.c @@ -0,0 +1,161 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Authors: Roy Zang <tie-fei.zang@freescale.com> + * Chunhe Lan <Chunhe.Lan@freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <pci.h> +#include <asm/io.h> +#include <asm/cache.h> +#include <asm/processor.h> +#include <asm/mmu.h> +#include <asm/immap_85xx.h> +#include <asm/fsl_pci.h> +#include <asm/fsl_ddr_sdram.h> +#include <asm/fsl_portals.h> +#include <libfdt.h> +#include <fdt_support.h> +#include <netdev.h> +#include <malloc.h> +#include <fm_eth.h> +#include <fsl_mdio.h> +#include <miiphy.h> +#include <phy.h> +#include <asm/fsl_dtsec.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + fsl_lbc_t *lbc = LBC_BASE_ADDR; + + /* Set ABSWP to implement conversion of addresses in the LBC */ + setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR); + + return 0; +} + +int checkboard(void) +{ + printf("Board: P1023 RDB\n"); + + return 0; +} + +#ifdef CONFIG_PCI +void pci_init_board(void) +{ + fsl_pcie_init_board(0); +} +#endif + +int board_early_init_r(void) +{ + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; + const u8 flash_esel = find_tlb_idx((void *)flashbase, 1); + + /* + * Remap Boot flash + PROMJET region to caching-inhibited + * so that flash can be erased properly. + */ + + /* Flush d-cache and invalidate i-cache of any FLASH data */ + flush_dcache(); + invalidate_icache(); + + /* invalidate existing TLB entry for flash + promjet */ + disable_tlb(flash_esel); + + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, flash_esel, BOOKE_PAGESZ_256M, 1); + + setup_portals(); + + return 0; +} + +unsigned long get_board_sys_clk(ulong dummy) +{ + return gd->bus_clk; +} + +unsigned long get_board_ddr_clk(ulong dummy) +{ + return gd->mem_clk; +} + +int board_eth_init(bd_t *bis) +{ + ccsr_gur_t *gur = (ccsr_gur_t *)CONFIG_SYS_MPC85xx_GUTS_ADDR; + struct fsl_pq_mdio_info dtsec_mdio_info; + + /* + * Need to set dTSEC 1 pin multiplexing to TSEC. The default setting + * is not correct. + */ + setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TSEC1_1); + + dtsec_mdio_info.regs = + (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR; + dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME; + + /* Register the 1G MDIO bus */ + fsl_pq_mdio_init(bis, &dtsec_mdio_info); + + fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR); + fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR); + + fm_info_set_mdio(FM1_DTSEC1, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + fm_info_set_mdio(FM1_DTSEC2, + miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME)); + +#ifdef CONFIG_FMAN_ENET + cpu_eth_init(bis); +#endif + + return pci_eth_init(bis); +} + +#if defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + phys_addr_t base; + phys_size_t size; + + ft_cpu_setup(blob, bd); + + base = getenv_bootm_low(); + size = getenv_bootm_size(); + + fdt_fixup_memory(blob, (u64)base, (u64)size); + +#ifdef CONFIG_HAS_FSL_DR_USB + fdt_fixup_dr_usb(blob, bd); +#endif + + fdt_fixup_fman_ethernet(blob); +} +#endif diff --git a/board/freescale/p1023rdb/tlb.c b/board/freescale/p1023rdb/tlb.c new file mode 100644 index 0000000000..3417c0f019 --- /dev/null +++ b/board/freescale/p1023rdb/tlb.c @@ -0,0 +1,115 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/mmu.h> + +struct fsl_e_tlb_entry tlb_table[] = { + /* TLB 0 - for temp stack in cache */ + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 0, BOOKE_PAGESZ_4K, 0), + + /* TLB 1 */ + /* *I*** - Covers boot page */ + SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I, + 0, 0, BOOKE_PAGESZ_4K, 1), + + /* *I*G* - CCSRBAR */ + SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 1, BOOKE_PAGESZ_4M, 1), + + /* W**G* - Flash, localbus */ + /* This will be changed to *I*G* after relocation to RAM. */ + SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 2, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 3, BOOKE_PAGESZ_1G, 1), + + /* *I*G* - PCI */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000, + CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 4, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000, + CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 5, BOOKE_PAGESZ_256M, 1), + + /* *I*G* - PCI I/O */ + SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 6, BOOKE_PAGESZ_256K, 1), + + /* Bman/Qman */ + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, 0, + 0, 7, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 8, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS, + MAS3_SW|MAS3_SR, MAS2_M, + 0, 9, BOOKE_PAGESZ_1M, 1), + SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000, + CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 10, BOOKE_PAGESZ_1M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS, + MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, + 0, 11, BOOKE_PAGESZ_16K, 1), + +#ifdef CONFIG_SYS_RAMBOOT + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, + CONFIG_SYS_DDR_SDRAM_BASE, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 12, BOOKE_PAGESZ_256M, 1), + + SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, + CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000, + MAS3_SX|MAS3_SW|MAS3_SR, 0, + 0, 13, BOOKE_PAGESZ_256M, 1), +#endif +}; + +int num_tlb_entries = ARRAY_SIZE(tlb_table); diff --git a/board/freescale/t4qds/tlb.c b/board/freescale/t4qds/tlb.c index 92c01cf95c..a138d5a9e6 100644 --- a/board/freescale/t4qds/tlb.c +++ b/board/freescale/t4qds/tlb.c @@ -55,6 +55,15 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 0, BOOKE_PAGESZ_1M, 1), +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) + /* + * SRIO_PCIE_BOOT-SLAVE. When slave boot, the address of the + * space is at 0xfff00000, it covered the 0xfffff000. + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G, + 0, 0, BOOKE_PAGESZ_1M, 1), #else SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, @@ -130,6 +139,16 @@ struct fsl_e_tlb_entry tlb_table[] = { SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS, MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, 0, 17, BOOKE_PAGESZ_4K, 1), +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE + /* + * SRIO_PCIE_BOOT-SLAVE. 1M space from 0xffe00000 for + * fetching ucode and ENV from master + */ + SET_TLB_ENTRY(1, CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR, + CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS, + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_G, + 0, 18, BOOKE_PAGESZ_1M, 1), +#endif }; diff --git a/board/ifm/ac14xx/ac14xx.c b/board/ifm/ac14xx/ac14xx.c index 74425912d6..dc2aff0993 100644 --- a/board/ifm/ac14xx/ac14xx.c +++ b/board/ifm/ac14xx/ac14xx.c @@ -23,6 +23,10 @@ #include <i2c.h> #endif +static int eeprom_diag; +static int mac_diag; +static int gpio_diag; + DECLARE_GLOBAL_DATA_PTR; static void gpio_configure(void) @@ -37,7 +41,7 @@ static void gpio_configure(void) /* * out_be32(&gpioregs->gpdir, 0xC2293020); - * workaround for a hardware affect: configure direction in pieces, + * workaround for a hardware effect: configure direction in pieces, * setting all outputs at once drops the reset line too low and * makes us lose the MII connection (breaks ethernet for us) */ @@ -126,8 +130,6 @@ static u32 gpio_querykbd(void) /* excerpt from the recovery's hw_info.h */ -static int eeprom_diag = 1; - struct __attribute__ ((__packed__)) eeprom_layout { char magic[3]; /** 'ifm' */ u8 len[2]; /** content length without magic/len fields */ @@ -209,6 +211,7 @@ static int read_eeprom(void) int mac_read_from_eeprom(void) { const u8 *mac; + const char *mac_txt; if (read_eeprom()) { printf("I2C EEPROM read failed.\n"); @@ -230,8 +233,13 @@ int mac_read_from_eeprom(void) if (mac && is_valid_ether_addr(mac)) { eth_setenv_enetaddr("ethaddr", mac); - printf("DIAG: %s() MAC value [%s]\n", - __func__, getenv("ethaddr")); + if (mac_diag) { + mac_txt = getenv("ethaddr"); + if (mac_txt) + printf("DIAG: MAC value [%s]\n", mac_txt); + else + printf("DIAG: failed to setup MAC env\n"); + } } return 0; @@ -326,42 +334,38 @@ int misc_init_r(void) gpio_configure(); /* - * check the GPIO keyboard, - * enforced start of the recovery when + * enforce the start of the recovery system when * - the appropriate keys were pressed - * - a previous installation was aborted or has failed * - "some" external software told us to + * - a previous installation was aborted or has failed */ want_recovery = 0; keys = gpio_querykbd(); - printf("GPIO keyboard status [0x%08X]\n", keys); - /* XXX insist in the _exact_ combination? */ + if (gpio_diag) + printf("GPIO keyboard status [0x%02X]\n", keys); if ((keys & GPIOKEY_BITS_RECOVERY) == GPIOKEY_BITS_RECOVERY) { - printf("GPIO keyboard requested RECOVERY\n"); - /* XXX TODO - * refine the logic to detect the first keypress, and - * wait to recheck IF it was the recovery combination? - */ + printf("detected recovery request (keyboard)\n"); want_recovery = 1; } - s = getenv("install_in_progress"); + s = getenv("want_recovery"); if ((s != NULL) && (*s != '\0')) { - printf("previous installation aborted, running RECOVERY\n"); + printf("detected recovery request (environment)\n"); want_recovery = 1; } - s = getenv("install_failed"); + s = getenv("install_in_progress"); if ((s != NULL) && (*s != '\0')) { - printf("previous installation FAILED, running RECOVERY\n"); + printf("previous installation has not completed\n"); want_recovery = 1; } - s = getenv("want_recovery"); + s = getenv("install_failed"); if ((s != NULL) && (*s != '\0')) { - printf("running RECOVERY according to the request\n"); + printf("previous installation has failed\n"); want_recovery = 1; } - - if (want_recovery) + if (want_recovery) { + printf("enforced start of the recovery system\n"); setenv("bootcmd", "run recovery"); + } /* * boot the recovery system without waiting; boot the diff --git a/board/isee/igep0033/board.c b/board/isee/igep0033/board.c index 826ceadd81..ea3bea50f5 100644 --- a/board/isee/igep0033/board.c +++ b/board/isee/igep0033/board.c @@ -36,37 +36,13 @@ DECLARE_GLOBAL_DATA_PTR; static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; -#ifdef CONFIG_SPL_BUILD -static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; -#endif /* MII mode defines */ #define RMII_MODE_ENABLE 0x4D static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; -/* UART Defines */ #ifdef CONFIG_SPL_BUILD -#define UART_RESET (0x1 << 1) -#define UART_CLK_RUNNING_MASK 0x1 -#define UART_SMART_IDLE_EN (0x1 << 0x3) - -static void rtc32k_enable(void) -{ - struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE; - - /* - * Unlock the RTC's registers. For more details please see the - * RTC_SS section of the TRM. In order to unlock we need to - * write these specific values (keys) in this order. - */ - writel(0x83e70b13, &rtc->kick0r); - writel(0x95a4f1e0, &rtc->kick1r); - - /* Enable the RTC 32K OSC by setting bits 3 and 6. */ - writel((1 << 3) | (1 << 6), &rtc->osc); -} - static const struct ddr_data ddr3_data = { .datardsratio0 = K4B2G1646EBIH9_RD_DQS, .datawdsratio0 = K4B2G1646EBIH9_WR_DQS, @@ -131,23 +107,9 @@ void s_init(void) /* Enable RTC32K clock */ rtc32k_enable(); - /* UART softreset */ - u32 regval; - enable_uart0_pin_mux(); - regval = readl(&uart_base->uartsyscfg); - regval |= UART_RESET; - writel(regval, &uart_base->uartsyscfg); - while ((readl(&uart_base->uartsyssts) & - UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK) - ; - - /* Disable smart idle */ - regval = readl(&uart_base->uartsyscfg); - regval |= UART_SMART_IDLE_EN; - writel(regval, &uart_base->uartsyscfg); - + uart_soft_reset(); gd = &gdata; preloader_console_init(); diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c index 93c611dfc6..0cca8d75b5 100644 --- a/board/phytec/pcm051/board.c +++ b/board/phytec/pcm051/board.c @@ -39,9 +39,6 @@ DECLARE_GLOBAL_DATA_PTR; static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; -#ifdef CONFIG_SPL_BUILD -static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; -#endif /* MII mode defines */ #define MII_MODE_ENABLE 0x0 @@ -50,31 +47,11 @@ static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; -/* UART defines */ #ifdef CONFIG_SPL_BUILD -#define UART_RESET (0x1 << 1) -#define UART_CLK_RUNNING_MASK 0x1 -#define UART_SMART_IDLE_EN (0x1 << 0x3) /* DDR RAM defines */ #define DDR_CLK_MHZ 303 /* DDR_DPLL_MULT value */ -static void rtc32k_enable(void) -{ - struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE; - - /* - * Unlock the RTC's registers. For more details please see the - * RTC_SS section of the TRM. In order to unlock we need to - * write these specific values (keys) in this order. - */ - writel(0x83e70b13, &rtc->kick0r); - writel(0x95a4f1e0, &rtc->kick1r); - - /* Enable the RTC 32K OSC by setting bits 3 and 6. */ - writel((1 << 3) | (1 << 6), &rtc->osc); -} - static const struct ddr_data ddr3_data = { .datardsratio0 = MT41J256M8HX15E_RD_DQS, .datawdsratio0 = MT41J256M8HX15E_WR_DQS, @@ -141,22 +118,8 @@ void s_init(void) /* Enable RTC32K clock */ rtc32k_enable(); - /* UART softreset */ - u32 regval; - enable_uart0_pin_mux(); - - regval = readl(&uart_base->uartsyscfg); - regval |= UART_RESET; - writel(regval, &uart_base->uartsyscfg); - while ((readl(&uart_base->uartsyssts) & UART_CLK_RUNNING_MASK) - != UART_CLK_RUNNING_MASK) - ; - - /* Disable smart idle */ - regval = readl(&uart_base->uartsyscfg); - regval |= UART_SMART_IDLE_EN; - writel(regval, &uart_base->uartsyscfg); + uart_soft_reset(); gd = &gdata; diff --git a/board/samsung/dts/exynos5250-smdk5250.dts b/board/samsung/dts/exynos5250-smdk5250.dts index 8da973b305..93375a64b2 100644 --- a/board/samsung/dts/exynos5250-smdk5250.dts +++ b/board/samsung/dts/exynos5250-smdk5250.dts @@ -30,6 +30,10 @@ spi2 = "/spi@12d40000"; spi3 = "/spi@131a0000"; spi4 = "/spi@131b0000"; + mmc0 = "/mmc@12200000"; + mmc1 = "/mmc@12210000"; + mmc2 = "/mmc@12220000"; + mmc3 = "/mmc@12230000"; }; sromc@12250000 { @@ -119,4 +123,24 @@ samsung,ycbcr-coeff = <0>; samsung,color-depth = <1>; }; + + mmc@12200000 { + samsung,bus-width = <8>; + samsung,timing = <1 3 3>; + samsung,removable = <0>; + }; + + mmc@12210000 { + status = "disabled"; + }; + + mmc@12220000 { + samsung,bus-width = <4>; + samsung,timing = <1 2 3>; + samsung,removable = <1>; + }; + + mmc@12230000 { + status = "disabled"; + }; }; diff --git a/board/samsung/dts/exynos5250-snow.dts b/board/samsung/dts/exynos5250-snow.dts index 24658c1989..d2ccc6675d 100644 --- a/board/samsung/dts/exynos5250-snow.dts +++ b/board/samsung/dts/exynos5250-snow.dts @@ -32,6 +32,33 @@ spi4 = "/spi@131b0000"; }; + i2c4: i2c@12ca0000 { + cros-ec@1e { + reg = <0x1e>; + compatible = "google,cros-ec"; + i2c-max-frequency = <100000>; + ec-interrupt = <&gpio 782 1>; + }; + + power-regulator@48 { + compatible = "ti,tps65090"; + reg = <0x48>; + }; + }; + + spi@131b0000 { + spi-max-frequency = <1000000>; + spi-deactivate-delay = <100>; + cros-ec@0 { + reg = <0>; + compatible = "google,cros-ec"; + spi-max-frequency = <5000000>; + ec-interrupt = <&gpio 782 1>; + optimise-flash-write; + status = "disabled"; + }; + }; + sound@12d60000 { samsung,i2s-epll-clock-frequency = <192000000>; samsung,i2s-sampling-rate = <48000>; @@ -69,4 +96,58 @@ samsung,dc-value = <25>; }; + cros-ec-keyb { + compatible = "google,cros-ec-keyb"; + google,key-rows = <8>; + google,key-columns = <13>; + google,repeat-delay-ms = <240>; + google,repeat-rate-ms = <30>; + google,ghost-filter; + /* + * Keymap entries take the form of 0xRRCCKKKK where + * RR=Row CC=Column KKKK=Key Code + * The values below are for a US keyboard layout and + * are taken from the Linux driver. Note that the + * 102ND key is not used for US keyboards. + */ + linux,keymap = < + /* CAPSLCK F1 B F10 */ + 0x0001003a 0x0002003b 0x00030030 0x00040044 + /* N = R_ALT ESC */ + 0x00060031 0x0008000d 0x000a0064 0x01010001 + /* F4 G F7 H */ + 0x0102003e 0x01030022 0x01040041 0x01060023 + /* ' F9 BKSPACE L_CTRL */ + 0x01080028 0x01090043 0x010b000e 0x0200001d + /* TAB F3 T F6 */ + 0x0201000f 0x0202003d 0x02030014 0x02040040 + /* ] Y 102ND [ */ + 0x0205001b 0x02060015 0x02070056 0x0208001a + /* F8 GRAVE F2 5 */ + 0x02090042 0x03010029 0x0302003c 0x03030006 + /* F5 6 - \ */ + 0x0304003f 0x03060007 0x0308000c 0x030b002b + /* R_CTRL A D F */ + 0x04000061 0x0401001e 0x04020020 0x04030021 + /* S K J ; */ + 0x0404001f 0x04050025 0x04060024 0x04080027 + /* L ENTER Z C */ + 0x04090026 0x040b001c 0x0501002c 0x0502002e + /* V X , M */ + 0x0503002f 0x0504002d 0x05050033 0x05060032 + /* L_SHIFT / . SPACE */ + 0x0507002a 0x05080035 0x05090034 0x050B0039 + /* 1 3 4 2 */ + 0x06010002 0x06020004 0x06030005 0x06040003 + /* 8 7 0 9 */ + 0x06050009 0x06060008 0x0608000b 0x0609000a + /* L_ALT DOWN RIGHT Q */ + 0x060a0038 0x060b006c 0x060c006a 0x07010010 + /* E R W I */ + 0x07020012 0x07030013 0x07040011 0x07050017 + /* U R_SHIFT P O */ + 0x07060016 0x07070036 0x07080019 0x07090018 + /* UP LEFT */ + 0x070b0067 0x070c0069>; + }; }; diff --git a/board/samsung/origen/lowlevel_init.S b/board/samsung/origen/lowlevel_init.S index 9daa0da614..be9d418265 100644 --- a/board/samsung/origen/lowlevel_init.S +++ b/board/samsung/origen/lowlevel_init.S @@ -87,12 +87,14 @@ lowlevel_init: 1: /* for UART */ bl uart_asm_init + bl arch_cpu_init bl tzpc_init pop {pc} wakeup_reset: bl system_clock_init bl mem_ctrl_asm_init + bl arch_cpu_init bl tzpc_init exit_wakeup: @@ -353,45 +355,3 @@ uart_asm_init: nop nop -/* Setting TZPC[TrustZone Protection Controller] */ -tzpc_init: - ldr r0, =TZPC0_BASE - mov r1, #R0SIZE - str r1, [r0] - mov r1, #DECPROTXSET - str r1, [r0, #TZPC_DECPROT0SET_OFFSET] - str r1, [r0, #TZPC_DECPROT1SET_OFFSET] - str r1, [r0, #TZPC_DECPROT2SET_OFFSET] - str r1, [r0, #TZPC_DECPROT3SET_OFFSET] - - ldr r0, =TZPC1_BASE - str r1, [r0, #TZPC_DECPROT0SET_OFFSET] - str r1, [r0, #TZPC_DECPROT1SET_OFFSET] - str r1, [r0, #TZPC_DECPROT2SET_OFFSET] - str r1, [r0, #TZPC_DECPROT3SET_OFFSET] - - ldr r0, =TZPC2_BASE - str r1, [r0, #TZPC_DECPROT0SET_OFFSET] - str r1, [r0, #TZPC_DECPROT1SET_OFFSET] - str r1, [r0, #TZPC_DECPROT2SET_OFFSET] - str r1, [r0, #TZPC_DECPROT3SET_OFFSET] - - ldr r0, =TZPC3_BASE - str r1, [r0, #TZPC_DECPROT0SET_OFFSET] - str r1, [r0, #TZPC_DECPROT1SET_OFFSET] - str r1, [r0, #TZPC_DECPROT2SET_OFFSET] - str r1, [r0, #TZPC_DECPROT3SET_OFFSET] - - ldr r0, =TZPC4_BASE - str r1, [r0, #TZPC_DECPROT0SET_OFFSET] - str r1, [r0, #TZPC_DECPROT1SET_OFFSET] - str r1, [r0, #TZPC_DECPROT2SET_OFFSET] - str r1, [r0, #TZPC_DECPROT3SET_OFFSET] - - ldr r0, =TZPC5_BASE - str r1, [r0, #TZPC_DECPROT0SET_OFFSET] - str r1, [r0, #TZPC_DECPROT1SET_OFFSET] - str r1, [r0, #TZPC_DECPROT2SET_OFFSET] - str r1, [r0, #TZPC_DECPROT3SET_OFFSET] - - mov pc, lr diff --git a/board/samsung/origen/origen_setup.h b/board/samsung/origen/origen_setup.h index 930b948505..926a4ccc29 100644 --- a/board/samsung/origen/origen_setup.h +++ b/board/samsung/origen/origen_setup.h @@ -121,19 +121,6 @@ #define UBRDIV_OFFSET 0x28 #define UFRACVAL_OFFSET 0x2C -/* TZPC : Register Offsets */ -#define TZPC0_BASE 0x10110000 -#define TZPC1_BASE 0x10120000 -#define TZPC2_BASE 0x10130000 -#define TZPC3_BASE 0x10140000 -#define TZPC4_BASE 0x10150000 -#define TZPC5_BASE 0x10160000 - -#define TZPC_DECPROT0SET_OFFSET 0x804 -#define TZPC_DECPROT1SET_OFFSET 0x810 -#define TZPC_DECPROT2SET_OFFSET 0x81C -#define TZPC_DECPROT3SET_OFFSET 0x828 - /* CLK_SRC_CPU */ #define MUX_HPM_SEL_MOUTAPLL 0x0 #define MUX_HPM_SEL_SCLKMPLL 0x1 @@ -617,16 +604,4 @@ * UBRFRACVAL = ((((800MHz*10/(115200*16) -10))%10)*16/10) */ #define UFRACVAL_VAL 0x4 - -/* - * TZPC Register Value : - * R0SIZE: 0x0 : Size of secured ram - */ -#define R0SIZE 0x0 - -/* - * TZPC Decode Protection Register Value : - * DECPROTXSET: 0xFF : Set Decode region to non-secure - */ -#define DECPROTXSET 0xFF #endif diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile index 47c6a5a46b..f2c32ee4c8 100644 --- a/board/samsung/smdk5250/Makefile +++ b/board/samsung/smdk5250/Makefile @@ -28,12 +28,15 @@ SOBJS := lowlevel_init.o COBJS := clock_init.o COBJS += dmc_common.o dmc_init_ddr3.o -COBJS += tzpc_init.o COBJS += smdk5250_spl.o ifndef CONFIG_SPL_BUILD +ifdef CONFIG_OF_CONTROL +COBJS += exynos5-dt.o +else COBJS += smdk5250.o endif +endif ifdef CONFIG_SPL_BUILD COBJS += spl_boot.o diff --git a/board/samsung/smdk5250/clock_init.c b/board/samsung/smdk5250/clock_init.c index 5b9e82fdf7..b288e66f0e 100644 --- a/board/samsung/smdk5250/clock_init.c +++ b/board/samsung/smdk5250/clock_init.c @@ -28,10 +28,14 @@ #include <asm/arch/clk.h> #include <asm/arch/clock.h> #include <asm/arch/spl.h> +#include <asm/arch/dwmmc.h> #include "clock_init.h" #include "setup.h" +#define FSYS1_MMC0_DIV_MASK 0xff0f +#define FSYS1_MMC0_DIV_VAL 0x0701 + DECLARE_GLOBAL_DATA_PTR; struct arm_clk_ratios arm_clk_ratios[] = { @@ -664,3 +668,17 @@ void clock_init_dp_clock(void) /* We run DP at 267 Mhz */ setbits_le32(&clk->div_disp1_0, CLK_DIV_DISP1_0_FIMD1); } + +/* + * Set clock divisor value for booting from EMMC. + * Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz. + */ +void emmc_boot_clk_div_set(void) +{ + struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE; + unsigned int div_mmc; + + div_mmc = readl((unsigned int) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK; + div_mmc |= FSYS1_MMC0_DIV_VAL; + writel(div_mmc, (unsigned int) &clk->div_fsys1); +} diff --git a/board/samsung/smdk5250/clock_init.h b/board/samsung/smdk5250/clock_init.h index f751bcb65a..20a1d47e06 100644 --- a/board/samsung/smdk5250/clock_init.h +++ b/board/samsung/smdk5250/clock_init.h @@ -146,4 +146,9 @@ struct mem_timings *clock_get_mem_timings(void); * Initialize clock for the device */ void system_clock_init(void); + +/* + * Set clock divisor value for booting from EMMC. + */ +void emmc_boot_clk_div_set(void); #endif diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c new file mode 100644 index 0000000000..aacf43eaa4 --- /dev/null +++ b/board/samsung/smdk5250/exynos5-dt.c @@ -0,0 +1,468 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <cros_ec.h> +#include <fdtdec.h> +#include <asm/io.h> +#include <errno.h> +#include <i2c.h> +#include <netdev.h> +#include <spi.h> +#include <asm/arch/cpu.h> +#include <asm/arch/dwmmc.h> +#include <asm/arch/gpio.h> +#include <asm/arch/mmc.h> +#include <asm/arch/pinmux.h> +#include <asm/arch/power.h> +#include <asm/arch/sromc.h> +#include <power/pmic.h> +#include <power/max77686_pmic.h> +#include <tmu.h> + +DECLARE_GLOBAL_DATA_PTR; + +#if defined CONFIG_EXYNOS_TMU +/* + * Boot Time Thermal Analysis for SoC temperature threshold breach + */ +static void boot_temp_check(void) +{ + int temp; + + switch (tmu_monitor(&temp)) { + /* Status TRIPPED ans WARNING means corresponding threshold breach */ + case TMU_STATUS_TRIPPED: + puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n"); + set_ps_hold_ctrl(); + hang(); + break; + case TMU_STATUS_WARNING: + puts("EXYNOS_TMU: WARNING! Temperature very high\n"); + break; + /* + * TMU_STATUS_INIT means something is wrong with temperature sensing + * and TMU status was changed back from NORMAL to INIT. + */ + case TMU_STATUS_INIT: + default: + debug("EXYNOS_TMU: Unknown TMU state\n"); + } +} +#endif + +struct local_info { + struct cros_ec_dev *cros_ec_dev; /* Pointer to cros_ec device */ + int cros_ec_err; /* Error for cros_ec, 0 if ok */ +}; + +static struct local_info local; + +#ifdef CONFIG_USB_EHCI_EXYNOS +int board_usb_vbus_init(void) +{ + struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) + samsung_get_base_gpio_part1(); + + /* Enable VBUS power switch */ + s5p_gpio_direction_output(&gpio1->x2, 6, 1); + + /* VBUS turn ON time */ + mdelay(3); + + return 0; +} +#endif + +#ifdef CONFIG_SOUND_MAX98095 +static void board_enable_audio_codec(void) +{ + struct exynos5_gpio_part1 *gpio1 = (struct exynos5_gpio_part1 *) + samsung_get_base_gpio_part1(); + + /* Enable MAX98095 Codec */ + s5p_gpio_direction_output(&gpio1->x1, 7, 1); + s5p_gpio_set_pull(&gpio1->x1, 7, GPIO_PULL_NONE); +} +#endif + +struct cros_ec_dev *board_get_cros_ec_dev(void) +{ + return local.cros_ec_dev; +} + +static int board_init_cros_ec_devices(const void *blob) +{ + local.cros_ec_err = cros_ec_init(blob, &local.cros_ec_dev); + if (local.cros_ec_err) + return -1; /* Will report in board_late_init() */ + + return 0; +} + +int board_init(void) +{ + gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); + +#if defined CONFIG_EXYNOS_TMU + if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) { + debug("%s: Failed to init TMU\n", __func__); + return -1; + } + boot_temp_check(); +#endif + +#ifdef CONFIG_EXYNOS_SPI + spi_init(); +#endif + + if (board_init_cros_ec_devices(gd->fdt_blob)) + return -1; + +#ifdef CONFIG_USB_EHCI_EXYNOS + board_usb_vbus_init(); +#endif +#ifdef CONFIG_SOUND_MAX98095 + board_enable_audio_codec(); +#endif + return 0; +} + +int dram_init(void) +{ + int i; + u32 addr; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); + gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE); + } + return 0; +} + +#if defined(CONFIG_POWER) +static int pmic_reg_update(struct pmic *p, int reg, uint regval) +{ + u32 val; + int ret = 0; + + ret = pmic_reg_read(p, reg, &val); + if (ret) { + debug("%s: PMIC %d register read failed\n", __func__, reg); + return -1; + } + val |= regval; + ret = pmic_reg_write(p, reg, val); + if (ret) { + debug("%s: PMIC %d register write failed\n", __func__, reg); + return -1; + } + return 0; +} + +int power_init_board(void) +{ + struct pmic *p; + + set_ps_hold_ctrl(); + + i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); + + if (pmic_init(I2C_PMIC)) + return -1; + + p = pmic_get("MAX77686_PMIC"); + if (!p) + return -ENODEV; + + if (pmic_probe(p)) + return -1; + + if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN)) + return -1; + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT, + MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V)) + return -1; + + /* VDD_MIF */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT, + MAX77686_BUCK1OUT_1V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK1OUT); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL, + MAX77686_BUCK1CTRL_EN)) + return -1; + + /* VDD_ARM */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1, + MAX77686_BUCK2DVS1_1_3V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK2DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1, + MAX77686_BUCK2CTRL_ON)) + return -1; + + /* VDD_INT */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1, + MAX77686_BUCK3DVS1_1_0125V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK3DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL, + MAX77686_BUCK3CTRL_ON)) + return -1; + + /* VDD_G3D */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1, + MAX77686_BUCK4DVS1_1_2V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK4DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1, + MAX77686_BUCK3CTRL_ON)) + return -1; + + /* VDD_LDO2 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1, + MAX77686_LD02CTRL1_1_5V | EN_LDO)) + return -1; + + /* VDD_LDO3 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1, + MAX77686_LD03CTRL1_1_8V | EN_LDO)) + return -1; + + /* VDD_LDO5 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1, + MAX77686_LD05CTRL1_1_8V | EN_LDO)) + return -1; + + /* VDD_LDO10 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1, + MAX77686_LD10CTRL1_1_8V | EN_LDO)) + return -1; + + return 0; +} +#endif + +void dram_init_banksize(void) +{ + int i; + u32 addr, size; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); + size = get_ram_size((long *)addr, SDRAM_BANK_SIZE); + + gd->bd->bi_dram[i].start = addr; + gd->bd->bi_dram[i].size = size; + } +} + +static int decode_sromc(const void *blob, struct fdt_sromc *config) +{ + int err; + int node; + + node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC); + if (node < 0) { + debug("Could not find SROMC node\n"); + return node; + } + + config->bank = fdtdec_get_int(blob, node, "bank", 0); + config->width = fdtdec_get_int(blob, node, "width", 2); + + err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing, + FDT_SROM_TIMING_COUNT); + if (err < 0) { + debug("Could not decode SROMC configuration Error: %s\n", + fdt_strerror(err)); + return -FDT_ERR_NOTFOUND; + } + return 0; +} + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_SMC911X + u32 smc_bw_conf, smc_bc_conf; + struct fdt_sromc config; + fdt_addr_t base_addr; + int node; + + node = decode_sromc(gd->fdt_blob, &config); + if (node < 0) { + debug("%s: Could not find sromc configuration\n", __func__); + return 0; + } + node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215); + if (node < 0) { + debug("%s: Could not find lan9215 configuration\n", __func__); + return 0; + } + + /* We now have a node, so any problems from now on are errors */ + base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg"); + if (base_addr == FDT_ADDR_T_NONE) { + debug("%s: Could not find lan9215 address\n", __func__); + return -1; + } + + /* Ethernet needs data bus width of 16 bits */ + if (config.width != 2) { + debug("%s: Unsupported bus width %d\n", __func__, + config.width); + return -1; + } + smc_bw_conf = SROMC_DATA16_WIDTH(config.bank) + | SROMC_BYTE_ENABLE(config.bank); + + smc_bc_conf = SROMC_BC_TACS(config.timing[FDT_SROM_TACS]) | + SROMC_BC_TCOS(config.timing[FDT_SROM_TCOS]) | + SROMC_BC_TACC(config.timing[FDT_SROM_TACC]) | + SROMC_BC_TCOH(config.timing[FDT_SROM_TCOH]) | + SROMC_BC_TAH(config.timing[FDT_SROM_TAH]) | + SROMC_BC_TACP(config.timing[FDT_SROM_TACP]) | + SROMC_BC_PMC(config.timing[FDT_SROM_PMC]); + + /* Select and configure the SROMC bank */ + exynos_pinmux_config(PERIPH_ID_SROMC, config.bank); + s5p_config_sromc(config.bank, smc_bw_conf, smc_bc_conf); + return smc911x_initialize(0, base_addr); +#endif + return 0; +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + const char *board_name; + + board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL); + if (board_name == NULL) + printf("\nUnknown Board\n"); + else + printf("\nBoard: %s\n", board_name); + + return 0; +} +#endif + +#ifdef CONFIG_GENERIC_MMC +int board_mmc_init(bd_t *bis) +{ + int ret; + /* dwmmc initializattion for available channels */ + ret = exynos_dwmmc_init(gd->fdt_blob); + if (ret) + debug("dwmmc init failed\n"); + + return ret; +} +#endif + +static int board_uart_init(void) +{ + int err, uart_id, ret = 0; + + for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) { + err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE); + if (err) { + debug("UART%d not configured\n", + (uart_id - PERIPH_ID_UART0)); + ret |= err; + } + } + return ret; +} + +#ifdef CONFIG_BOARD_EARLY_INIT_F +int board_early_init_f(void) +{ + int err; + err = board_uart_init(); + if (err) { + debug("UART init failed\n"); + return err; + } +#ifdef CONFIG_SYS_I2C_INIT_BOARD + board_i2c_init(gd->fdt_blob); +#endif + return err; +} +#endif + +#ifdef CONFIG_LCD +void exynos_cfg_lcd_gpio(void) +{ + struct exynos5_gpio_part1 *gpio1 = + (struct exynos5_gpio_part1 *)samsung_get_base_gpio_part1(); + + /* For Backlight */ + s5p_gpio_cfg_pin(&gpio1->b2, 0, GPIO_OUTPUT); + s5p_gpio_set_value(&gpio1->b2, 0, 1); + + /* LCD power on */ + s5p_gpio_cfg_pin(&gpio1->x1, 5, GPIO_OUTPUT); + s5p_gpio_set_value(&gpio1->x1, 5, 1); + + /* Set Hotplug detect for DP */ + s5p_gpio_cfg_pin(&gpio1->x0, 7, GPIO_FUNC(0x3)); +} + +void exynos_set_dp_phy(unsigned int onoff) +{ + set_dp_phy_ctrl(onoff); +} +#endif + +#ifdef CONFIG_BOARD_LATE_INIT +int board_late_init(void) +{ + stdio_print_current_devices(); + + if (local.cros_ec_err) { + /* Force console on */ + gd->flags &= ~GD_FLG_SILENT; + + printf("cros-ec communications failure %d\n", + local.cros_ec_err); + puts("\nPlease reset with Power+Refresh\n\n"); + panic("Cannot init cros-ec device"); + return -1; + } + return 0; +} +#endif diff --git a/board/samsung/smdk5250/lowlevel_init.S b/board/samsung/smdk5250/lowlevel_init.S index bc6cb6f738..edc565ef72 100644 --- a/board/samsung/smdk5250/lowlevel_init.S +++ b/board/samsung/smdk5250/lowlevel_init.S @@ -75,12 +75,14 @@ lowlevel_init: bl mem_ctrl_init 1: + bl arch_cpu_init bl tzpc_init ldmia r13!, {ip,pc} wakeup_reset: bl system_clock_init bl mem_ctrl_init + bl arch_cpu_init bl tzpc_init exit_wakeup: diff --git a/board/samsung/smdk5250/setup.h b/board/samsung/smdk5250/setup.h index 34d8bc31f4..eb91d13109 100644 --- a/board/samsung/smdk5250/setup.h +++ b/board/samsung/smdk5250/setup.h @@ -28,18 +28,6 @@ #include <config.h> #include <asm/arch/dmc.h> -/* TZPC : Register Offsets */ -#define TZPC0_BASE 0x10100000 -#define TZPC1_BASE 0x10110000 -#define TZPC2_BASE 0x10120000 -#define TZPC3_BASE 0x10130000 -#define TZPC4_BASE 0x10140000 -#define TZPC5_BASE 0x10150000 -#define TZPC6_BASE 0x10160000 -#define TZPC7_BASE 0x10170000 -#define TZPC8_BASE 0x10180000 -#define TZPC9_BASE 0x10190000 - /* APLL_CON1 */ #define APLL_CON1_VAL (0x00203800) @@ -458,18 +446,6 @@ /* CLK_GATE_IP_DISP1 */ #define CLK_GATE_DP1_ALLOW (1 << 4) -/* - * TZPC Register Value : - * R0SIZE: 0x0 : Size of secured ram - */ -#define R0SIZE 0x0 - -/* - * TZPC Decode Protection Register Value : - * DECPROTXSET: 0xFF : Set Decode region to non-secure - */ -#define DECPROTXSET 0xFF - #define DDR3PHY_CTRL_PHY_RESET (1 << 0) #define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0) @@ -590,5 +566,4 @@ void update_reset_dll(struct exynos5_dmc *, enum ddr_mode); void sdelay(unsigned long); void mem_ctrl_init(void); void system_clock_init(void); -void tzpc_init(void); #endif diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index 8b09e1de42..276fd41328 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -29,6 +29,7 @@ #include <netdev.h> #include <spi.h> #include <asm/arch/cpu.h> +#include <asm/arch/dwmmc.h> #include <asm/arch/gpio.h> #include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> @@ -37,39 +38,9 @@ #include <asm/arch/dp_info.h> #include <power/pmic.h> #include <power/max77686_pmic.h> -#include <tmu.h> DECLARE_GLOBAL_DATA_PTR; -#if defined CONFIG_EXYNOS_TMU -/* - * Boot Time Thermal Analysis for SoC temperature threshold breach - */ -static void boot_temp_check(void) -{ - int temp; - - switch (tmu_monitor(&temp)) { - /* Status TRIPPED ans WARNING means corresponding threshold breach */ - case TMU_STATUS_TRIPPED: - puts("EXYNOS_TMU: TRIPPING! Device power going down ...\n"); - set_ps_hold_ctrl(); - hang(); - break; - case TMU_STATUS_WARNING: - puts("EXYNOS_TMU: WARNING! Temperature very high\n"); - break; - /* - * TMU_STATUS_INIT means something is wrong with temperature sensing - * and TMU status was changed back from NORMAL to INIT. - */ - case TMU_STATUS_INIT: - default: - debug("EXYNOS_TMU: Unknown TMU state\n"); - } -} -#endif - #ifdef CONFIG_USB_EHCI_EXYNOS int board_usb_vbus_init(void) { @@ -102,14 +73,6 @@ int board_init(void) { gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); -#if defined CONFIG_EXYNOS_TMU - if (tmu_init(gd->fdt_blob) != TMU_STATUS_NORMAL) { - debug("%s: Failed to init TMU\n", __func__); - return -1; - } - boot_temp_check(); -#endif - #ifdef CONFIG_EXYNOS_SPI spi_init(); #endif @@ -124,14 +87,13 @@ int board_init(void) int dram_init(void) { - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) - + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) - + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) - + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE) - + get_ram_size((long *)PHYS_SDRAM_5, PHYS_SDRAM_7_SIZE) - + get_ram_size((long *)PHYS_SDRAM_6, PHYS_SDRAM_7_SIZE) - + get_ram_size((long *)PHYS_SDRAM_7, PHYS_SDRAM_7_SIZE) - + get_ram_size((long *)PHYS_SDRAM_8, PHYS_SDRAM_8_SIZE); + int i; + u32 addr; + + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); + gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE); + } return 0; } @@ -254,57 +216,15 @@ int power_init_board(void) void dram_init_banksize(void) { - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, - PHYS_SDRAM_1_SIZE); - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, - PHYS_SDRAM_2_SIZE); - gd->bd->bi_dram[2].start = PHYS_SDRAM_3; - gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, - PHYS_SDRAM_3_SIZE); - gd->bd->bi_dram[3].start = PHYS_SDRAM_4; - gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, - PHYS_SDRAM_4_SIZE); - gd->bd->bi_dram[4].start = PHYS_SDRAM_5; - gd->bd->bi_dram[4].size = get_ram_size((long *)PHYS_SDRAM_5, - PHYS_SDRAM_5_SIZE); - gd->bd->bi_dram[5].start = PHYS_SDRAM_6; - gd->bd->bi_dram[5].size = get_ram_size((long *)PHYS_SDRAM_6, - PHYS_SDRAM_6_SIZE); - gd->bd->bi_dram[6].start = PHYS_SDRAM_7; - gd->bd->bi_dram[6].size = get_ram_size((long *)PHYS_SDRAM_7, - PHYS_SDRAM_7_SIZE); - gd->bd->bi_dram[7].start = PHYS_SDRAM_8; - gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8, - PHYS_SDRAM_8_SIZE); -} - -#ifdef CONFIG_OF_CONTROL -static int decode_sromc(const void *blob, struct fdt_sromc *config) -{ - int err; - int node; - - node = fdtdec_next_compatible(blob, 0, COMPAT_SAMSUNG_EXYNOS5_SROMC); - if (node < 0) { - debug("Could not find SROMC node\n"); - return node; - } - - config->bank = fdtdec_get_int(blob, node, "bank", 0); - config->width = fdtdec_get_int(blob, node, "width", 2); - - err = fdtdec_get_int_array(blob, node, "srom-timing", config->timing, - FDT_SROM_TIMING_COUNT); - if (err < 0) { - debug("Could not decode SROMC configuration\n"); - return -FDT_ERR_NOTFOUND; + int i; + u32 addr, size; + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { + addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE); + size = get_ram_size((long *)addr, SDRAM_BANK_SIZE); + gd->bd->bi_dram[i].start = addr; + gd->bd->bi_dram[i].size = size; } - - return 0; } -#endif int board_eth_init(bd_t *bis) { @@ -313,27 +233,6 @@ int board_eth_init(bd_t *bis) struct fdt_sromc config; fdt_addr_t base_addr; -#ifdef CONFIG_OF_CONTROL - int node; - - node = decode_sromc(gd->fdt_blob, &config); - if (node < 0) { - debug("%s: Could not find sromc configuration\n", __func__); - return 0; - } - node = fdtdec_next_compatible(gd->fdt_blob, node, COMPAT_SMSC_LAN9215); - if (node < 0) { - debug("%s: Could not find lan9215 configuration\n", __func__); - return 0; - } - - /* We now have a node, so any problems from now on are errors */ - base_addr = fdtdec_get_addr(gd->fdt_blob, node, "reg"); - if (base_addr == FDT_ADDR_T_NONE) { - debug("%s: Could not find lan9215 address\n", __func__); - return -1; - } -#else /* Non-FDT configuration - bank number and timing parameters*/ config.bank = CONFIG_ENV_SROM_BANK; config.width = 2; @@ -346,7 +245,6 @@ int board_eth_init(bd_t *bis) config.timing[FDT_SROM_TACP] = 0x09; config.timing[FDT_SROM_PMC] = 0x01; base_addr = CONFIG_SMC911X_BASE; -#endif /* Ethernet needs data bus width of 16 bits */ if (config.width != 2) { @@ -376,17 +274,7 @@ int board_eth_init(bd_t *bis) #ifdef CONFIG_DISPLAY_BOARDINFO int checkboard(void) { -#ifdef CONFIG_OF_CONTROL - const char *board_name; - - board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL); - if (board_name == NULL) - printf("\nUnknown Board\n"); - else - printf("\nBoard: %s\n", board_name); -#else printf("\nBoard: SMDK5250\n"); -#endif return 0; } #endif @@ -394,48 +282,54 @@ int checkboard(void) #ifdef CONFIG_GENERIC_MMC int board_mmc_init(bd_t *bis) { - int err; + int err, ret = 0, index, bus_width; + u32 base; err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - if (err) { + if (err) debug("SDMMC0 not configured\n"); - return err; - } - - err = s5p_mmc_init(0, 8); - return err; + ret |= err; + + /*EMMC: dwmmc Channel-0 with 8 bit bus width */ + index = 0; + base = samsung_get_base_mmc() + (0x10000 * index); + bus_width = 8; + err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL); + if (err) + debug("dwmmc Channel-0 init failed\n"); + ret |= err; + + err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); + if (err) + debug("SDMMC2 not configured\n"); + ret |= err; + + /*SD: dwmmc Channel-2 with 4 bit bus width */ + index = 2; + base = samsung_get_base_mmc() + (0x10000 * index); + bus_width = 4; + err = exynos_dwmci_add_port(index, base, bus_width, (u32)NULL); + if (err) + debug("dwmmc Channel-2 init failed\n"); + ret |= err; + + return ret; } #endif static int board_uart_init(void) { - int err; - - err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); - if (err) { - debug("UART0 not configured\n"); - return err; + int err, uart_id, ret = 0; + + for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) { + err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE); + if (err) { + debug("UART%d not configured\n", + (uart_id - PERIPH_ID_UART0)); + ret |= err; + } } - - err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); - if (err) { - debug("UART1 not configured\n"); - return err; - } - - err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); - if (err) { - debug("UART2 not configured\n"); - return err; - } - - err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); - if (err) { - debug("UART3 not configured\n"); - return err; - } - - return 0; + return ret; } #ifdef CONFIG_BOARD_EARLY_INIT_F @@ -448,7 +342,7 @@ int board_early_init_f(void) return err; } #ifdef CONFIG_SYS_I2C_INIT_BOARD - board_i2c_init(gd->fdt_blob); + board_i2c_init(NULL); #endif return err; } @@ -477,7 +371,6 @@ void exynos_set_dp_phy(unsigned int onoff) set_dp_phy_ctrl(onoff); } -#ifndef CONFIG_OF_CONTROL vidinfo_t panel_info = { .vl_freq = 60, .vl_col = 2560, @@ -543,13 +436,9 @@ static struct exynos_dp_platform_data dp_platform_data = { .edp_dev_info = &edp_info, }; -#endif void init_panel_info(vidinfo_t *vid) { -#ifndef CONFIG_OF_CONTROL - vid->rgb_mode = MODE_RGB_P, - + vid->rgb_mode = MODE_RGB_P; exynos_set_dp_platform_data(&dp_platform_data); -#endif } #endif diff --git a/board/samsung/smdk5250/spl_boot.c b/board/samsung/smdk5250/spl_boot.c index c0bcf460f1..98f2286f9e 100644 --- a/board/samsung/smdk5250/spl_boot.c +++ b/board/samsung/smdk5250/spl_boot.c @@ -23,16 +23,44 @@ #include<common.h> #include<config.h> +#include <asm/arch-exynos/dmc.h> +#include <asm/arch/clock.h> +#include <asm/arch/clk.h> + +#include "clock_init.h" + +/* Index into irom ptr table */ +enum index { + MMC_INDEX, + EMMC44_INDEX, + EMMC44_END_INDEX, + SPI_INDEX, + USB_INDEX, +}; + +/* IROM Function Pointers Table */ +u32 irom_ptr_table[] = { + [MMC_INDEX] = 0x02020030, /* iROM Function Pointer-SDMMC boot */ + [EMMC44_INDEX] = 0x02020044, /* iROM Function Pointer-EMMC4.4 boot*/ + [EMMC44_END_INDEX] = 0x02020048,/* iROM Function Pointer + -EMMC4.4 end boot operation */ + [SPI_INDEX] = 0x02020058, /* iROM Function Pointer-SPI boot */ + [USB_INDEX] = 0x02020070, /* iROM Function Pointer-USB boot*/ + }; + enum boot_mode { BOOT_MODE_MMC = 4, BOOT_MODE_SERIAL = 20, + BOOT_MODE_EMMC = 8, /* EMMC4.4 */ /* Boot based on Operating Mode pin settings */ BOOT_MODE_OM = 32, BOOT_MODE_USB, /* Boot using USB download */ }; - typedef u32 (*spi_copy_func_t)(u32 offset, u32 nblock, u32 dst); - typedef u32 (*usb_copy_func_t)(void); +void *get_irom_func(int index) +{ + return (void *)*(u32 *)irom_ptr_table[index]; +} /* * Set/clear program flow prediction and return the previous state. @@ -55,13 +83,15 @@ static int config_branch_prediction(int set_cr_z) */ void copy_uboot_to_ram(void) { - spi_copy_func_t spi_copy; - usb_copy_func_t usb_copy; - int is_cr_z_set; unsigned int sec_boot_check; enum boot_mode bootmode = BOOT_MODE_OM; - u32 (*copy_bl2)(u32, u32, u32); + + u32 (*spi_copy)(u32 offset, u32 nblock, u32 dst); + u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst); + u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst); + void (*end_bootop_from_emmc)(void); + u32 (*usb_copy)(void); /* Read iRAM location to check for secondary USB boot mode */ sec_boot_check = readl(EXYNOS_IRAM_SECONDARY_BASE); @@ -73,14 +103,24 @@ void copy_uboot_to_ram(void) switch (bootmode) { case BOOT_MODE_SERIAL: - spi_copy = *(spi_copy_func_t *)EXYNOS_COPY_SPI_FNPTR_ADDR; + spi_copy = get_irom_func(SPI_INDEX); spi_copy(SPI_FLASH_UBOOT_POS, CONFIG_BL2_SIZE, - CONFIG_SYS_TEXT_BASE); + CONFIG_SYS_TEXT_BASE); break; case BOOT_MODE_MMC: - copy_bl2 = (void *) *(u32 *)COPY_BL2_FNPTR_ADDR; + copy_bl2 = get_irom_func(MMC_INDEX); copy_bl2(BL2_START_OFFSET, BL2_SIZE_BLOC_COUNT, - CONFIG_SYS_TEXT_BASE); + CONFIG_SYS_TEXT_BASE); + break; + case BOOT_MODE_EMMC: + /* Set the FSYS1 clock divisor value for EMMC boot */ + emmc_boot_clk_div_set(); + + copy_bl2_from_emmc = get_irom_func(EMMC44_INDEX); + end_bootop_from_emmc = get_irom_func(EMMC44_END_INDEX); + + copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE); + end_bootop_from_emmc(); break; case BOOT_MODE_USB: /* @@ -88,8 +128,7 @@ void copy_uboot_to_ram(void) * before copy from USB device to RAM */ is_cr_z_set = config_branch_prediction(0); - usb_copy = *(usb_copy_func_t *) - EXYNOS_COPY_USB_FNPTR_ADDR; + usb_copy = get_irom_func(USB_INDEX); usb_copy(); config_branch_prediction(is_cr_z_set); break; @@ -117,5 +156,4 @@ void board_init_r(gd_t *id, ulong dest_addr) while (1) ; } - void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) {} diff --git a/board/samsung/smdkv310/lowlevel_init.S b/board/samsung/smdkv310/lowlevel_init.S index 7a1ea98aed..31e0e2edaf 100644 --- a/board/samsung/smdkv310/lowlevel_init.S +++ b/board/samsung/smdkv310/lowlevel_init.S @@ -85,12 +85,14 @@ lowlevel_init: 1: /* for UART */ bl uart_asm_init + bl arch_cpu_init bl tzpc_init pop {pc} wakeup_reset: bl system_clock_init bl mem_ctrl_asm_init + bl arch_cpu_init bl tzpc_init exit_wakeup: @@ -410,61 +412,3 @@ uart_asm_init: nop nop nop - -/* Setting TZPC[TrustZone Protection Controller] */ -tzpc_init: - ldr r0, =0x10110000 - mov r1, #0x0 - str r1, [r0] - mov r1, #0xff - str r1, [r0, #0x0804] - str r1, [r0, #0x0810] - str r1, [r0, #0x081C] - str r1, [r0, #0x0828] - - ldr r0, =0x10120000 - mov r1, #0x0 - str r1, [r0] - mov r1, #0xff - str r1, [r0, #0x0804] - str r1, [r0, #0x0810] - str r1, [r0, #0x081C] - str r1, [r0, #0x0828] - - ldr r0, =0x10130000 - mov r1, #0x0 - str r1, [r0] - mov r1, #0xff - str r1, [r0, #0x0804] - str r1, [r0, #0x0810] - str r1, [r0, #0x081C] - str r1, [r0, #0x0828] - - ldr r0, =0x10140000 - mov r1, #0x0 - str r1, [r0] - mov r1, #0xff - str r1, [r0, #0x0804] - str r1, [r0, #0x0810] - str r1, [r0, #0x081C] - str r1, [r0, #0x0828] - - ldr r0, =0x10150000 - mov r1, #0x0 - str r1, [r0] - mov r1, #0xff - str r1, [r0, #0x0804] - str r1, [r0, #0x0810] - str r1, [r0, #0x081C] - str r1, [r0, #0x0828] - - ldr r0, =0x10160000 - mov r1, #0x0 - str r1, [r0] - mov r1, #0xff - str r1, [r0, #0x0804] - str r1, [r0, #0x0810] - str r1, [r0, #0x081C] - str r1, [r0, #0x0828] - - mov pc, lr diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c index 638cc4d68b..fdbe26cde1 100644 --- a/board/ti/am335x/board.c +++ b/board/ti/am335x/board.c @@ -38,9 +38,6 @@ DECLARE_GLOBAL_DATA_PTR; static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; -#ifdef CONFIG_SPL_BUILD -static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; -#endif /* MII mode defines */ #define MII_MODE_ENABLE 0x0 @@ -126,28 +123,7 @@ static int read_eeprom(void) return 0; } -/* UART Defines */ #ifdef CONFIG_SPL_BUILD -#define UART_RESET (0x1 << 1) -#define UART_CLK_RUNNING_MASK 0x1 -#define UART_SMART_IDLE_EN (0x1 << 0x3) - -static void rtc32k_enable(void) -{ - struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE; - - /* - * Unlock the RTC's registers. For more details please see the - * RTC_SS section of the TRM. In order to unlock we need to - * write these specific values (keys) in this order. - */ - writel(0x83e70b13, &rtc->kick0r); - writel(0x95a4f1e0, &rtc->kick1r); - - /* Enable the RTC 32K OSC by setting bits 3 and 6. */ - writel((1 << 3) | (1 << 6), &rtc->osc); -} - static const struct ddr_data ddr2_data = { .datardsratio0 = ((MT47H128M16RT25E_RD_DQS<<30) | (MT47H128M16RT25E_RD_DQS<<20) | @@ -339,9 +315,6 @@ void s_init(void) /* Enable RTC32K clock */ rtc32k_enable(); - /* UART softreset */ - u32 regVal; - #ifdef CONFIG_SERIAL1 enable_uart0_pin_mux(); #endif /* CONFIG_SERIAL1 */ @@ -361,17 +334,7 @@ void s_init(void) enable_uart5_pin_mux(); #endif /* CONFIG_SERIAL6 */ - regVal = readl(&uart_base->uartsyscfg); - regVal |= UART_RESET; - writel(regVal, &uart_base->uartsyscfg); - while ((readl(&uart_base->uartsyssts) & - UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK) - ; - - /* Disable smart idle */ - regVal = readl(&uart_base->uartsyscfg); - regVal |= UART_SMART_IDLE_EN; - writel(regVal, &uart_base->uartsyscfg); + uart_soft_reset(); gd = &gdata; diff --git a/board/ti/panda/panda.c b/board/ti/panda/panda.c index 90ae29e7c6..1da5b359c0 100644 --- a/board/ti/panda/panda.c +++ b/board/ti/panda/panda.c @@ -37,6 +37,11 @@ #endif #define PANDA_ULPI_PHY_TYPE_GPIO 182 +#define PANDA_BOARD_ID_1_GPIO 101 +#define PANDA_ES_BOARD_ID_1_GPIO 48 +#define PANDA_BOARD_ID_2_GPIO 171 +#define PANDA_ES_BOARD_ID_3_GPIO 3 +#define PANDA_ES_BOARD_ID_4_GPIO 2 DECLARE_GLOBAL_DATA_PTR; @@ -66,6 +71,73 @@ int board_eth_init(bd_t *bis) return 0; } +/* +* Routine: get_board_revision +* Description: Detect if we are running on a panda revision A1-A6, +* or an ES panda board. This can be done by reading +* the level of GPIOs and checking the processor revisions. +* This should result in: +* Panda 4430: +* GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5 +* GPIO171, GPIO101, GPIO182: 1 0 1 => A6 +* Panda ES: +* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2 +* GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3 +*/ +int get_board_revision(void) +{ + int board_id0, board_id1, board_id2; + int board_id3, board_id4; + int board_id; + + int processor_rev = omap_revision(); + + /* Setup the mux for the common board ID pins (gpio 171 and 182) */ + writew((IEN | M3), (*ctrl)->control_padconf_core_base + UNIPRO_TX0); + writew((IEN | M3), (*ctrl)->control_padconf_core_base + FREF_CLK2_OUT); + + board_id0 = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO); + board_id2 = gpio_get_value(PANDA_BOARD_ID_2_GPIO); + + if ((processor_rev >= OMAP4460_ES1_0 && + processor_rev <= OMAP4460_ES1_1)) { + /* + * Setup the mux for the ES specific board ID pins (gpio 101, + * 2 and 3. + */ + writew((IEN | M3), (*ctrl)->control_padconf_core_base + + GPMC_A24); + writew((IEN | M3), (*ctrl)->control_padconf_core_base + + UNIPRO_RY0); + writew((IEN | M3), (*ctrl)->control_padconf_core_base + + UNIPRO_RX1); + + board_id1 = gpio_get_value(PANDA_ES_BOARD_ID_1_GPIO); + board_id3 = gpio_get_value(PANDA_ES_BOARD_ID_3_GPIO); + board_id4 = gpio_get_value(PANDA_ES_BOARD_ID_4_GPIO); + +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es")); +#endif + board_id = ((board_id4 << 4) | (board_id3 << 3) | + (board_id2 << 2) | (board_id1 << 1) | (board_id0)); + } else { + /* Setup the mux for the Ax specific board ID pins (gpio 101) */ + writew((IEN | M3), (*ctrl)->control_padconf_core_base + + FREF_CLK2_OUT); + + board_id1 = gpio_get_value(PANDA_BOARD_ID_1_GPIO); + board_id = ((board_id2 << 2) | (board_id1 << 1) | (board_id0)); + +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + if ((board_id >= 0x3) && (processor_rev == OMAP4430_ES2_3)) + setenv("board_name", strcat(CONFIG_SYS_BOARD, "-a4")); +#endif + } + + return board_id; +} + /** * @brief misc_init_r - Configure Panda board specific configurations * such as power configurations, ethernet initialization as phase2 of @@ -82,11 +154,7 @@ int misc_init_r(void) if (omap_revision() == OMAP4430_ES1_0) return 0; -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - if (omap_revision() >= OMAP4460_ES1_0 || - omap_revision() <= OMAP4460_ES1_1) - setenv("board_name", strcat(CONFIG_SYS_BOARD, "-es")); -#endif + get_board_revision(); gpio_direction_input(PANDA_ULPI_PHY_TYPE_GPIO); phy_type = gpio_get_value(PANDA_ULPI_PHY_TYPE_GPIO); @@ -106,7 +174,7 @@ int misc_init_r(void) auxclk |= AUXCLK_ENABLE_MASK; writel(auxclk, &scrm->auxclk3); - } else { + } else { /* ULPI PHY supplied by auxclk1 derived from PER dpll */ debug("ULPI PHY supplied by auxclk1\n"); @@ -151,9 +219,9 @@ void set_muxconf_regs_essential(void) if (omap_revision() >= OMAP4460_ES1_0) do_set_mux((*ctrl)->control_padconf_wkup_base, - wkup_padconf_array_essential_4460, - sizeof(wkup_padconf_array_essential_4460) / - sizeof(struct pad_conf_entry)); + wkup_padconf_array_essential_4460, + sizeof(wkup_padconf_array_essential_4460) / + sizeof(struct pad_conf_entry)); } void set_muxconf_regs_non_essential(void) @@ -165,14 +233,14 @@ void set_muxconf_regs_non_essential(void) if (omap_revision() < OMAP4460_ES1_0) do_set_mux((*ctrl)->control_padconf_core_base, - core_padconf_array_non_essential_4430, - sizeof(core_padconf_array_non_essential_4430) / - sizeof(struct pad_conf_entry)); + core_padconf_array_non_essential_4430, + sizeof(core_padconf_array_non_essential_4430) / + sizeof(struct pad_conf_entry)); else do_set_mux((*ctrl)->control_padconf_core_base, - core_padconf_array_non_essential_4460, - sizeof(core_padconf_array_non_essential_4460) / - sizeof(struct pad_conf_entry)); + core_padconf_array_non_essential_4460, + sizeof(core_padconf_array_non_essential_4460) / + sizeof(struct pad_conf_entry)); do_set_mux((*ctrl)->control_padconf_wkup_base, wkup_padconf_array_non_essential, @@ -181,9 +249,9 @@ void set_muxconf_regs_non_essential(void) if (omap_revision() < OMAP4460_ES1_0) do_set_mux((*ctrl)->control_padconf_wkup_base, - wkup_padconf_array_non_essential_4430, - sizeof(wkup_padconf_array_non_essential_4430) / - sizeof(struct pad_conf_entry)); + wkup_padconf_array_non_essential_4430, + sizeof(wkup_padconf_array_non_essential_4430) / + sizeof(struct pad_conf_entry)); } #if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC) diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c index 4759b167a4..6ad3dd8fc7 100644 --- a/board/ti/ti814x/evm.c +++ b/board/ti/ti814x/evm.c @@ -37,49 +37,16 @@ DECLARE_GLOBAL_DATA_PTR; #ifdef CONFIG_SPL_BUILD static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE; -static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE; #endif static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE; /* UART Defines */ #ifdef CONFIG_SPL_BUILD -#define UART_RESET (0x1 << 1) -#define UART_CLK_RUNNING_MASK 0x1 -#define UART_SMART_IDLE_EN (0x1 << 0x3) - -static void rtc32k_enable(void) -{ - struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE; - - /* - * Unlock the RTC's registers. For more details please see the - * RTC_SS section of the TRM. In order to unlock we need to - * write these specific values (keys) in this order. - */ - writel(0x83e70b13, &rtc->kick0r); - writel(0x95a4f1e0, &rtc->kick1r); - - /* Enable the RTC 32K OSC by setting bits 3 and 6. */ - writel((1 << 3) | (1 << 6), &rtc->osc); -} - static void uart_enable(void) { - u32 regVal; - /* UART softreset */ - regVal = readl(&uart_base->uartsyscfg); - regVal |= UART_RESET; - writel(regVal, &uart_base->uartsyscfg); - while ((readl(&uart_base->uartsyssts) & - UART_CLK_RUNNING_MASK) != UART_CLK_RUNNING_MASK) - ; - - /* Disable smart idle */ - regVal = readl(&uart_base->uartsyscfg); - regVal |= UART_SMART_IDLE_EN; - writel(regVal, &uart_base->uartsyscfg); + uart_soft_reset(); } static void wdt_disable(void) diff --git a/board/vpac270/u-boot-spl.lds b/board/vpac270/u-boot-spl.lds index 61d1154aff..1a3ef9285f 100644 --- a/board/vpac270/u-boot-spl.lds +++ b/board/vpac270/u-boot-spl.lds @@ -67,11 +67,6 @@ SECTIONS __rel_dyn_end = .; } - .dynsym : { - __dynsym_start = .; - *(.dynsym) - } - . = ALIGN(0x800); _end = .; @@ -84,6 +79,7 @@ SECTIONS } /DISCARD/ : { *(.bss*) } + /DISCARD/ : { *(.dynsym) } /DISCARD/ : { *(.dynstr*) } /DISCARD/ : { *(.dynsym*) } /DISCARD/ : { *(.dynamic*) } |
