diff options
Diffstat (limited to 'board')
33 files changed, 456 insertions, 1941 deletions
diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c index dc7d89d82d..b4f7f81583 100644 --- a/board/Marvell/gplugd/gplugd.c +++ b/board/Marvell/gplugd/gplugd.c @@ -32,6 +32,13 @@ #include <mvmfp.h> #include <asm/arch/mfp.h> #include <asm/arch/armada100.h> +#include <asm/gpio.h> +#include <miiphy.h> + +#ifdef CONFIG_ARMADA100_FEC +#include <net.h> +#include <netdev.h> +#endif /* CONFIG_ARMADA100_FEC */ DECLARE_GLOBAL_DATA_PTR; @@ -45,6 +52,26 @@ int board_early_init_f(void) /* Enable Console on UART3 */ MFPO8_UART3_TXD, MFPO9_UART3_RXD, + + /* Ethernet PHY Interface */ + MFP086_ETH_TXCLK, + MFP087_ETH_TXEN, + MFP088_ETH_TXDQ3, + MFP089_ETH_TXDQ2, + MFP090_ETH_TXDQ1, + MFP091_ETH_TXDQ0, + MFP092_ETH_CRS, + MFP093_ETH_COL, + MFP094_ETH_RXCLK, + MFP095_ETH_RXER, + MFP096_ETH_RXDQ3, + MFP097_ETH_RXDQ2, + MFP098_ETH_RXDQ1, + MFP099_ETH_RXDQ0, + MFP100_ETH_MDC, + MFP101_ETH_MDIO, + MFP103_ETH_RXDV, + MFP_EOC /*End of configuration*/ }; /* configure MFP's */ @@ -58,5 +85,49 @@ int board_init(void) gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD; /* adress of boot parameters */ gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100; + /* Assert PHY_RST# */ + gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW); + udelay(10); + /* Deassert PHY_RST# */ + gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH); return 0; } + +#ifdef CONFIG_ARMADA100_FEC +int board_eth_init(bd_t *bis) +{ + struct armd1apmu_registers *apmu_regs = + (struct armd1apmu_registers *)ARMD1_APMU_BASE; + + /* Enable clock of ethernet controller */ + writel(FE_CLK_RST | FE_CLK_ENA, &apmu_regs->fecrc); + + return armada100_fec_register(ARMD1_FEC_BASE); +} + +#ifdef CONFIG_RESET_PHY_R +/* Configure and initialize PHY chip 88E3015 */ +void reset_phy(void) +{ + u16 phy_adr; + const char *name = "armd-fec0"; + + if (miiphy_set_current_dev(name)) + return; + + /* command to read PHY dev address */ + if (miiphy_read(name, 0xff, 0xff, &phy_adr)) { + printf("Err..%s could not read PHY dev address\n", __func__); + return; + } + + /* Set Ethernet LED in TX blink mode */ + miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00); + miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL); + + /* reset the phy */ + miiphy_reset(name, phy_adr); + debug("88E3015 Initialized on %s\n", name); +} +#endif /* CONFIG_RESET_PHY_R */ +#endif /* CONFIG_ARMADA100_FEC */ diff --git a/board/bf537-stamp/Makefile b/board/bf537-stamp/Makefile index 2b9328be32..49e441472b 100644 --- a/board/bf537-stamp/Makefile +++ b/board/bf537-stamp/Makefile @@ -31,7 +31,7 @@ LIB = $(obj)lib$(BOARD).o COBJS-y := $(BOARD).o COBJS-$(CONFIG_BFIN_IDE) += ide-cf.o -COBJS-$(CONFIG_HAS_POST) += post.o post-memory.o +COBJS-$(CONFIG_HAS_POST) += post-memory.o SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c) OBJS := $(addprefix $(obj),$(COBJS-y)) diff --git a/board/bf537-stamp/post-memory.c b/board/bf537-stamp/post-memory.c index 49022dc930..2dea92fbe9 100644 --- a/board/bf537-stamp/post-memory.c +++ b/board/bf537-stamp/post-memory.c @@ -13,7 +13,6 @@ #define SCLK_NUM 3 void post_out_buff(char *buff); -int post_key_pressed(void); void post_init_pll(int mult, int div); int post_init_sdram(int sclk); void post_init_uart(int sclk); @@ -52,7 +51,7 @@ int memory_post_test(int flags) sclk_temp -= CONFIG_SCLK_DIV; sclk = sclk * 1000000; post_init_uart(sclk); - if (post_key_pressed() == 0) + if (post_hotkeys_pressed() == 0) return 0; for (m = 0; m < CCLK_NUM; m++) { @@ -130,66 +129,6 @@ void post_out_buff(char *buff) ; } -/* Using sw10-PF5 as the hotkey */ -#define KEY_LOOP 0x80000 -#define KEY_DELAY 0x80 -int post_key_pressed(void) -{ - int i, n; - unsigned short value; - - bfin_write_PORTF_FER(bfin_read_PORTF_FER() & ~PF5); - bfin_write_PORTFIO_DIR(bfin_read_PORTFIO_DIR() & ~PF5); - bfin_write_PORTFIO_INEN(bfin_read_PORTFIO_INEN() | PF5); - SSYNC(); - - post_out_buff("########Press SW10 to enter Memory POST########: 3\0"); - for (i = 0; i < KEY_LOOP; i++) { - value = bfin_read_PORTFIO() & PF5; - if (bfin_read_UART0_RBR() == 0x0D) { - value = 0; - goto key_pressed; - } - if (value != 0) - goto key_pressed; - for (n = 0; n < KEY_DELAY; n++) - asm("nop"); - } - post_out_buff("\b2\0"); - - for (i = 0; i < KEY_LOOP; i++) { - value = bfin_read_PORTFIO() & PF5; - if (bfin_read_UART0_RBR() == 0x0D) { - value = 0; - goto key_pressed; - } - if (value != 0) - goto key_pressed; - for (n = 0; n < KEY_DELAY; n++) - asm("nop"); - } - post_out_buff("\b1\0"); - - for (i = 0; i < KEY_LOOP; i++) { - value = bfin_read_PORTFIO() & PF5; - if (bfin_read_UART0_RBR() == 0x0D) { - value = 0; - goto key_pressed; - } - if (value != 0) - goto key_pressed; - for (n = 0; n < KEY_DELAY; n++) - asm("nop"); - } - key_pressed: - post_out_buff("\b0"); - post_out_buff("\n\r\0"); - if (value == 0) - return 0; - post_out_buff("Hotkey has been pressed, Enter POST . . . . . .\n\r\0"); - return 1; -} - void post_init_pll(int mult, int div) { diff --git a/board/bf537-stamp/post.c b/board/bf537-stamp/post.c deleted file mode 100644 index 60eed5f68a..0000000000 --- a/board/bf537-stamp/post.c +++ /dev/null @@ -1,174 +0,0 @@ -/* - * BF537-STAMP POST code - * - * Enter bugs at http://blackfin.uclinux.org/ - * - * Copyright (c) 2005-2009 Analog Devices Inc. - * - * Licensed under the GPL-2 or later. - */ - -#include <common.h> -#include <config.h> -#include <command.h> -#include <asm/blackfin.h> -#include <asm/gpio.h> - -/* Using sw10-PF5 as the hotkey */ -int post_hotkeys_pressed(void) -{ - int delay = 3; - int i; - unsigned short value; - - gpio_request(GPIO_PF5, "post"); - gpio_direction_input(GPIO_PF5); - - printf("########Press SW10 to enter Memory POST########: %2d ", delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = gpio_get_value(GPIO_PF5); - if (value != 0) { - break; - } - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - printf("\b\b\b 0"); - printf("\n"); - if (value == 0) - return 0; - else { - printf("Hotkey has been pressed, Enter POST . . . . . .\n"); - return 1; - } - - gpio_free(GPIO_PF5); -} - -int uart_post_test(int flags) -{ - return 0; -} - -#define BLOCK_SIZE 0x10000 -#define VERIFY_ADDR 0x2000000 -extern int erase_block_flash(int); -extern int write_data(long lStart, long lCount, uchar * pnData); -int flash_post_test(int flags) -{ - unsigned short *pbuf, *temp; - int offset, n, i; - int value = 0; - int result = 0; - printf("\n"); - pbuf = (unsigned short *)VERIFY_ADDR; - temp = pbuf; - for (n = FLASH_START_POST_BLOCK; n < FLASH_END_POST_BLOCK; n++) { - offset = (n - 7) * BLOCK_SIZE; - printf("--------Erase block:%2d..", n); - erase_block_flash(n); - printf("OK\r"); - printf("--------Program block:%2d...", n); - write_data(CONFIG_SYS_FLASH_BASE + offset, BLOCK_SIZE, pbuf); - printf("OK\r"); - printf("--------Verify block:%2d...", n); - for (i = 0; i < BLOCK_SIZE; i += 2) { - if (*(unsigned short *)(CONFIG_SYS_FLASH_BASE + offset + i) != - *temp++) { - value = 1; - result = 1; - } - } - if (value) - printf("failed\n"); - else - printf("OK %3d%%\r", - (int)( - (n + 1 - - FLASH_START_POST_BLOCK) * - 100 / (FLASH_END_POST_BLOCK - - FLASH_START_POST_BLOCK))); - - temp = pbuf; - value = 0; - } - printf("\n"); - if (result) - return -1; - else - return 0; -} - -/**************************************************** - * LED1 ---- PF6 LED2 ---- PF7 * - * LED3 ---- PF8 LED4 ---- PF9 * - * LED5 ---- PF10 LED6 ---- PF11 * - ****************************************************/ -int led_post_test(int flags) -{ - unsigned int leds[] = { - GPIO_PF6, GPIO_PF7, GPIO_PF8, - GPIO_PF9, GPIO_PF10, GPIO_PF11, - }; - int i; - - for (i = 0; i < ARRAY_SIZE(leds); ++i) { - gpio_request(leds[i], "post"); - gpio_direction_output(leds[i], 0); - - printf("LED%i on", i + 1); - gpio_set_value(leds[i], 1); - udelay(1000000); - printf("\b\b\b\b\b\b\b"); - - gpio_free(leds[i]); - } - - return 0; -} - -/************************************************ - * SW10 ---- PF5 SW11 ---- PF4 * - * SW12 ---- PF3 SW13 ---- PF2 * - ************************************************/ -int button_post_test(int flags) -{ - unsigned int buttons[] = { - GPIO_PF2, GPIO_PF3, GPIO_PF4, GPIO_PF5, - }; - unsigned int sws[] = { 13, 12, 11, 10, }; - int i, delay = 5; - unsigned short value = 0; - int result = 0; - - for (i = 0; i < ARRAY_SIZE(buttons); ++i) { - gpio_request(buttons[i], "post"); - gpio_direction_input(buttons[i]); - - delay = 5; - printf("\n--------Press SW%i: %2d ", sws[i], delay); - while (delay--) { - for (i = 0; i < 100; i++) { - value = gpio_get_value(buttons[i]); - if (value != 0) - break; - udelay(10000); - } - printf("\b\b\b%2d ", delay); - } - if (value != 0) - puts("\b\bOK"); - else { - result = -1; - puts("\b\bfailed"); - } - - gpio_free(buttons[i]); - } - - puts("\n"); - - return result; -} diff --git a/board/efikamx/efikamx.c b/board/efikamx/efikamx.c index 5be1f6ca58..0c4e24bb4c 100644 --- a/board/efikamx/efikamx.c +++ b/board/efikamx/efikamx.c @@ -62,10 +62,13 @@ void efikamx_toggle_led(uint32_t mask); #define EFIKAMX_BOARD_REV_13 0x3 #define EFIKAMX_BOARD_REV_14 0x4 +#define EFIKASB_BOARD_REV_13 0x1 +#define EFIKASB_BOARD_REV_20 0x2 + /* * Board identification */ -u32 get_efika_rev(void) +u32 get_efikamx_rev(void) { u32 rev = 0; /* @@ -97,6 +100,31 @@ u32 get_efika_rev(void) return (~rev & 0x7) + 1; } +inline u32 get_efikasb_rev(void) +{ + u32 rev = 0; + + mxc_request_iomux(MX51_PIN_EIM_CS3, IOMUX_CONFIG_GPIO); + mxc_iomux_set_pad(MX51_PIN_EIM_CS3, PAD_CTL_100K_PU); + gpio_direction_input(IOMUX_TO_GPIO(MX51_PIN_EIM_CS3)); + rev |= (!!gpio_get_value(IOMUX_TO_GPIO(MX51_PIN_EIM_CS3))) << 0; + + mxc_request_iomux(MX51_PIN_EIM_CS4, IOMUX_CONFIG_GPIO); + mxc_iomux_set_pad(MX51_PIN_EIM_CS4, PAD_CTL_100K_PU); + gpio_direction_input(IOMUX_TO_GPIO(MX51_PIN_EIM_CS4)); + rev |= (!!gpio_get_value(IOMUX_TO_GPIO(MX51_PIN_EIM_CS4))) << 1; + + return rev; +} + +inline uint32_t get_efika_rev(void) +{ + if (machine_is_efikamx()) + return get_efikamx_rev(); + else + return get_efikasb_rev(); +} + u32 get_board_rev(void) { return get_cpu_rev() | (get_efika_rev() << 8); @@ -268,25 +296,36 @@ struct fsl_esdhc_cfg esdhc_cfg[2] = { {MMC_SDHC2_BASE_ADDR, 1}, }; +static inline uint32_t efika_mmc_cd(void) +{ + if (machine_is_efikamx()) + return MX51_PIN_GPIO1_0; + else + return MX51_PIN_EIM_CS2; +} + int board_mmc_getcd(u8 *absent, struct mmc *mmc) { struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + uint32_t cd = efika_mmc_cd(); if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR) - *absent = gpio_get_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_0)); + *absent = gpio_get_value(IOMUX_TO_GPIO(cd)); else *absent = gpio_get_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_8)); return 0; } + int board_mmc_init(bd_t *bis) { int ret; + uint32_t cd = efika_mmc_cd(); /* SDHC1 is used on all revisions, setup control pins first */ - mxc_request_iomux(MX51_PIN_GPIO1_0, + mxc_request_iomux(cd, IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); - mxc_iomux_set_pad(MX51_PIN_GPIO1_0, + mxc_iomux_set_pad(cd, PAD_CTL_DRV_HIGH | PAD_CTL_HYS_ENABLE | PAD_CTL_PUE_KEEPER | PAD_CTL_100K_PU | PAD_CTL_ODE_OPENDRAIN_NONE | @@ -298,11 +337,12 @@ int board_mmc_init(bd_t *bis) PAD_CTL_100K_PU | PAD_CTL_ODE_OPENDRAIN_NONE | PAD_CTL_SRE_FAST); - gpio_direction_input(IOMUX_TO_GPIO(MX51_PIN_GPIO1_0)); + gpio_direction_input(IOMUX_TO_GPIO(cd)); gpio_direction_input(IOMUX_TO_GPIO(MX51_PIN_GPIO1_1)); /* Internal SDHC1 IOMUX + SDHC2 IOMUX on old boards */ - if (get_efika_rev() < EFIKAMX_BOARD_REV_12) { + if (machine_is_efikasb() || (machine_is_efikamx() && + (get_efika_rev() < EFIKAMX_BOARD_REV_12))) { /* SDHC1 IOMUX */ mxc_request_iomux(MX51_PIN_SD1_CMD, IOMUX_CONFIG_ALT0 | IOMUX_CONFIG_SION); @@ -414,6 +454,7 @@ int board_mmc_init(bd_t *bis) ret = fsl_esdhc_initialize(bis, &esdhc_cfg[0]); } + return ret; } #endif @@ -493,27 +534,44 @@ static inline void setup_iomux_ata(void) { } */ void setup_iomux_led(void) { - /* Blue LED */ - mxc_request_iomux(MX51_PIN_CSI1_D9, IOMUX_CONFIG_ALT3); - gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_CSI1_D9), 0); - - /* Green LED */ - mxc_request_iomux(MX51_PIN_CSI1_VSYNC, IOMUX_CONFIG_ALT3); - gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_CSI1_VSYNC), 0); - - /* Red LED */ - mxc_request_iomux(MX51_PIN_CSI1_HSYNC, IOMUX_CONFIG_ALT3); - gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_CSI1_HSYNC), 0); + if (machine_is_efikamx()) { + /* Blue LED */ + mxc_request_iomux(MX51_PIN_CSI1_D9, IOMUX_CONFIG_ALT3); + gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_CSI1_D9), 0); + + /* Green LED */ + mxc_request_iomux(MX51_PIN_CSI1_VSYNC, IOMUX_CONFIG_ALT3); + gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_CSI1_VSYNC), 0); + + /* Red LED */ + mxc_request_iomux(MX51_PIN_CSI1_HSYNC, IOMUX_CONFIG_ALT3); + gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_CSI1_HSYNC), 0); + } else { + /* CAPS-LOCK LED */ + mxc_request_iomux(MX51_PIN_EIM_CS0, IOMUX_CONFIG_GPIO); + gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_EIM_CS0), 0); + + /* ALARM-LED LED */ + mxc_request_iomux(MX51_PIN_GPIO1_3, IOMUX_CONFIG_GPIO); + gpio_direction_output(IOMUX_TO_GPIO(MX51_PIN_GPIO1_3), 0); + } } void efikamx_toggle_led(uint32_t mask) { - gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_CSI1_D9), - mask & EFIKAMX_LED_BLUE); - gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_CSI1_VSYNC), - mask & EFIKAMX_LED_GREEN); - gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_CSI1_HSYNC), - mask & EFIKAMX_LED_RED); + if (machine_is_efikamx()) { + gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_CSI1_D9), + mask & EFIKAMX_LED_BLUE); + gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_CSI1_VSYNC), + mask & EFIKAMX_LED_GREEN); + gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_CSI1_HSYNC), + mask & EFIKAMX_LED_RED); + } else { + gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_EIM_CS0), + mask & EFIKAMX_LED_BLUE); + gpio_set_value(IOMUX_TO_GPIO(MX51_PIN_GPIO1_3), + !(mask & EFIKAMX_LED_GREEN)); + } } /* @@ -607,7 +665,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX51_EFIKAMX; gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; return 0; @@ -629,7 +686,24 @@ int board_late_init(void) int checkboard(void) { - puts("Board: Efika MX\n"); + u32 rev = get_efika_rev(); + + if (machine_is_efikamx()) { + printf("Board: Efika MX, rev1.%i\n", rev & 0xf); + return 0; + } else { + switch (rev) { + case EFIKASB_BOARD_REV_13: + printf("Board: Efika SB rev1.3\n"); + break; + case EFIKASB_BOARD_REV_20: + printf("Board: Efika SB rev2.0\n"); + break; + default: + printf("Board: Efika SB, rev Unknown\n"); + break; + } + } return 0; } diff --git a/board/efikamx/imximage.cfg b/board/efikamx/imximage_mx.cfg index 6fe0ff9ac4..6fe0ff9ac4 100644 --- a/board/efikamx/imximage.cfg +++ b/board/efikamx/imximage_mx.cfg diff --git a/board/efikamx/imximage_sb.cfg b/board/efikamx/imximage_sb.cfg new file mode 100644 index 0000000000..878146f442 --- /dev/null +++ b/board/efikamx/imximage_sb.cfg @@ -0,0 +1,122 @@ +# +# Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com> +# +# BASED ON: imx51evk +# +# (C) Copyright 2009 +# Stefano Babic DENX Software Engineering sbabic@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not write to the Free Software +# Foundation Inc. 51 Franklin Street Fifth Floor Boston, +# MA 02110-1301 USA +# +# Refer docs/README.imxmage for more details about how-to configure +# and create imximage boot image +# +# The syntax is taken as close as possible with the kwbimage + +# Boot Device : one of +# spi, sd (the board has no nand neither onenand) +BOOT_FROM spi + +# Device Configuration Data (DCD) +# +# Each entry must have the format: +# Addr-type Address Value +# +# where: +# Addr-type register length (1,2 or 4 bytes) +# Address absolute address of the register +# value value to be stored in the register + +# Setting IOMUXC +DATA 4 0x73fa88a0 0x200 +DATA 4 0x73fa850c 0x20c3 +DATA 4 0x73fa8510 0x20c3 +DATA 4 0x73fa883c 0x2 +DATA 4 0x73fa8848 0x2 +DATA 4 0x73fa84b8 0xe7 +DATA 4 0x73fa84bc 0x45 +DATA 4 0x73fa84c0 0x45 +DATA 4 0x73fa84c4 0x45 +DATA 4 0x73fa84c8 0x45 +DATA 4 0x73fa8820 0x0 +DATA 4 0x73fa84a4 0x5 +DATA 4 0x73fa84a8 0x5 +DATA 4 0x73fa84ac 0xe3 +DATA 4 0x73fa84b0 0xe3 +DATA 4 0x73fa84b4 0xe3 +DATA 4 0x73fa84cc 0xe3 +DATA 4 0x73fa84d0 0xe2 + +DATA 4 0x73fa882c 0x4 +DATA 4 0x73fa88a4 0x4 +DATA 4 0x73fa88ac 0x4 +DATA 4 0x73fa88b8 0x4 + +# Setting DDR for micron +# 13 Rows, 10 Cols, 32 bit, SREF=4 Micron Model +# CAS=3 BL=4 +# ESDCTL_ESDCTL0 +DATA 4 0x83fd9000 0x82a20000 +# ESDCTL_ESDCTL1 +DATA 4 0x83fd9008 0x82a20000 +# ESDCTL_ESDMISC +DATA 4 0x83fd9010 0xcaaaf6d0 +# ESDCTL_ESDCFG0 +DATA 4 0x83fd9004 0x333574aa +# ESDCTL_ESDCFG1 +DATA 4 0x83fd900c 0x333574aa + +# Init DRAM on CS0 +# ESDCTL_ESDSCR +DATA 4 0x83fd9014 0x04008008 +DATA 4 0x83fd9014 0x0000801a +DATA 4 0x83fd9014 0x0000801b +DATA 4 0x83fd9014 0x00448019 +DATA 4 0x83fd9014 0x07328018 +DATA 4 0x83fd9014 0x04008008 +DATA 4 0x83fd9014 0x00008010 +DATA 4 0x83fd9014 0x00008010 +DATA 4 0x83fd9014 0x06328018 +DATA 4 0x83fd9014 0x03808019 +DATA 4 0x83fd9014 0x00408019 +DATA 4 0x83fd9014 0x00008000 + +# Init DRAM on CS1 +DATA 4 0x83fd9014 0x0400800c +DATA 4 0x83fd9014 0x0000801e +DATA 4 0x83fd9014 0x0000801f +DATA 4 0x83fd9014 0x0000801d +DATA 4 0x83fd9014 0x0732801c +DATA 4 0x83fd9014 0x0400800c +DATA 4 0x83fd9014 0x00008014 +DATA 4 0x83fd9014 0x00008014 +DATA 4 0x83fd9014 0x0632801c +DATA 4 0x83fd9014 0x0380801d +DATA 4 0x83fd9014 0x0040801d +DATA 4 0x83fd9014 0x00008004 + +# Write to CTL0 +DATA 4 0x83fd9000 0xb2a20000 +# Write to CTL1 +DATA 4 0x83fd9008 0xb2a20000 +# ESDMISC +DATA 4 0x83fd9010 0xcaaaf6d0 +#ESDCTL_ESDCDLYGD +DATA 4 0x83fd9034 0x90000000 +DATA 4 0x83fd9014 0x00000000 diff --git a/board/sbc8260/Makefile b/board/freescale/mx25pdk/Makefile index f1d86fc173..4d45ae3745 100644 --- a/board/sbc8260/Makefile +++ b/board/freescale/mx25pdk/Makefile @@ -1,9 +1,7 @@ # -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de> # -# See file CREDITS for list of people who contributed to this -# project. +# (C) Copyright 2011 Freescale Semiconductor, Inc. # # This program is free software; you can redistribute it and/or # modify it under the terms of the GNU General Public License as @@ -25,20 +23,21 @@ include $(TOPDIR)/config.mk LIB = $(obj)lib$(BOARD).o -COBJS := sbc8260.o flash.o +COBJS := mx25pdk.o +SOBJS := lowlevel_init.o SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(COBJS)) SOBJS := $(addprefix $(obj),$(SOBJS)) -$(LIB): $(obj).depend $(OBJS) - $(call cmd_link_o_target, $(OBJS)) +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) clean: rm -f $(SOBJS) $(OBJS) distclean: clean - rm -f $(LIB) core *.bak $(obj).depend + rm -f $(LIB) core *.bak .depend ######################################################################### diff --git a/board/freescale/mx25pdk/imximage.cfg b/board/freescale/mx25pdk/imximage.cfg new file mode 100644 index 0000000000..f7af7ff1d0 --- /dev/null +++ b/board/freescale/mx25pdk/imximage.cfg @@ -0,0 +1,73 @@ +# +# (C) Copyright 2009 +# Stefano Babic DENX Software Engineering sbabic@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# Refer docs/README.imxmage for more details about how-to configure +# and create imximage boot image +# +# The syntax is taken as close as possible with the kwbimage + +# Boot Device : one of +# spi, sd (the board has no nand neither onenand) + +BOOT_FROM sd + +# Device Configuration Data (DCD) +# +# Each entry must have the format: +# Addr-type Address Value +# +# where: +# Addr-type register length (1,2 or 4 bytes) +# Address absolute address of the register +# value value to be stored in the register + +# EIM config-CS5 init -- CPLD +DATA 4 0xB8002050 0x0000D843 +DATA 4 0xB8002054 0x22252521 +DATA 4 0xB8002058 0x22220A00 + +# DDR2 init +DATA 4 0xB8001004 0x0076E83A +DATA 4 0xB8001010 0x00000204 +DATA 4 0xB8001000 0x92210000 +DATA 4 0x80000f00 0x12344321 +DATA 4 0xB8001000 0xB2210000 +DATA 1 0x82000000 0xda +DATA 1 0x83000000 0xda +DATA 1 0x81000400 0xda +DATA 1 0x80000333 0xda + +DATA 4 0xB8001000 0x92210000 +DATA 1 0x80000400 0x12345678 + +DATA 4 0xB8001000 0xA2210000 +DATA 4 0x80000000 0x87654321 +DATA 4 0x80000000 0x87654321 + +DATA 4 0xB8001000 0xB2210000 +DATA 1 0x80000233 0xda +DATA 1 0x81000780 0xda +DATA 1 0x81000400 0xda +DATA 4 0xB8001000 0x82216080 +DATA 4 0x43FAC454 0x00001000 + +DATA 4 0x53F80008 0x20034000 + +# Enable the clocks +DATA 4 0x53f8000c 0x1fffffff +DATA 4 0x53f80010 0xffffffff +DATA 4 0x53f80014 0xfdfff diff --git a/board/freescale/mx25pdk/lowlevel_init.S b/board/freescale/mx25pdk/lowlevel_init.S new file mode 100644 index 0000000000..6e6810fa54 --- /dev/null +++ b/board/freescale/mx25pdk/lowlevel_init.S @@ -0,0 +1,21 @@ +/* + * Copyright (c) 2011 Freescale Semiconductor + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +.globl lowlevel_init +lowlevel_init: + + mov pc, lr diff --git a/board/freescale/mx25pdk/mx25pdk.c b/board/freescale/mx25pdk/mx25pdk.c new file mode 100644 index 0000000000..4a8352fb3d --- /dev/null +++ b/board/freescale/mx25pdk/mx25pdk.c @@ -0,0 +1,56 @@ +/* + * (C) Copyright 2011 Freescale Semiconductor, Inc. + * + * Author: Fabio Estevam <fabio.estevam@freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/imx25-pinmux.h> +#include <asm/arch/sys_proto.h> + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + /* dram_init must store complete ramsize in gd->ram_size */ + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, + PHYS_SDRAM_1_SIZE); + return 0; +} + +int board_early_init_f(void) +{ + mx25_uart1_init_pins(); + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + + return 0; +} + +int checkboard(void) +{ + puts("Board: MX25PDK\n"); + + return 0; +} diff --git a/board/freescale/mx31ads/mx31ads.c b/board/freescale/mx31ads/mx31ads.c index 7637c9281c..4dd1e63a83 100644 --- a/board/freescale/mx31ads/mx31ads.c +++ b/board/freescale/mx31ads/mx31ads.c @@ -36,12 +36,6 @@ int dram_init(void) return 0; } -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; -} - int board_early_init_f(void) { int i; @@ -105,7 +99,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX31ADS; /* board id for linux */ gd->bd->bi_boot_params = 0x80000100; /* adress of boot parameters */ return 0; diff --git a/board/freescale/mx31pdk/mx31pdk.c b/board/freescale/mx31pdk/mx31pdk.c index f6e190ac6b..276d45153a 100644 --- a/board/freescale/mx31pdk/mx31pdk.c +++ b/board/freescale/mx31pdk/mx31pdk.c @@ -47,12 +47,6 @@ int dram_init(void) return 0; } -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; -} - int board_early_init_f(void) { /* CS5: CPLD incl. network controller */ @@ -69,7 +63,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX31_3DS; /* board id for linux */ /* adress of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 94ea1f2905..8da1ee8b1a 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -403,7 +403,6 @@ int board_init(void) { system_rev = get_cpu_rev(); - gd->bd->bi_arch_number = MACH_TYPE_MX51_BABBAGE; /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; diff --git a/board/freescale/mx53ard/mx53ard.c b/board/freescale/mx53ard/mx53ard.c index 6e3360b65f..c89da13327 100644 --- a/board/freescale/mx53ard/mx53ard.c +++ b/board/freescale/mx53ard/mx53ard.c @@ -278,7 +278,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX53_ARD; /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; diff --git a/board/freescale/mx53evk/mx53evk.c b/board/freescale/mx53evk/mx53evk.c index 81857ffed3..fd821c0b1d 100644 --- a/board/freescale/mx53evk/mx53evk.c +++ b/board/freescale/mx53evk/mx53evk.c @@ -355,7 +355,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX53_EVK; /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c index ade100608d..156f8b5a3a 100644 --- a/board/freescale/mx53loco/mx53loco.c +++ b/board/freescale/mx53loco/mx53loco.c @@ -288,7 +288,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX53_LOCO; gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; return 0; diff --git a/board/freescale/mx53smd/mx53smd.c b/board/freescale/mx53smd/mx53smd.c index 4a7ee550d5..776784f5ec 100644 --- a/board/freescale/mx53smd/mx53smd.c +++ b/board/freescale/mx53smd/mx53smd.c @@ -214,7 +214,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX53_SMD; /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; diff --git a/board/isee/igep0020/igep0020.c b/board/isee/igep0020/igep0020.c index 2279cc0e36..6a3777eb8c 100644 --- a/board/isee/igep0020/igep0020.c +++ b/board/isee/igep0020/igep0020.c @@ -29,6 +29,7 @@ #include <asm/arch/mmc_host_def.h> #include <asm/arch/mux.h> #include <asm/arch/sys_proto.h> +#include <asm/arch/omap_gpmc.h> #include <asm/mach-types.h> #include "igep0020.h" diff --git a/board/isee/igep0020/igep0020.h b/board/isee/igep0020/igep0020.h index c08d758326..3d6e15fb73 100644 --- a/board/isee/igep0020/igep0020.h +++ b/board/isee/igep0020/igep0020.h @@ -29,15 +29,6 @@ const omap3_sysinfo sysinfo = { "ONENAND", }; -/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */ -#define NET_LAN9221_GPMC_CONFIG1 0x00001000 -#define NET_LAN9221_GPMC_CONFIG2 0x00080701 -#define NET_LAN9221_GPMC_CONFIG3 0x00020201 -#define NET_LAN9221_GPMC_CONFIG4 0x08030703 -#define NET_LAN9221_GPMC_CONFIG5 0x00060908 -#define NET_LAN9221_GPMC_CONFIG6 0x87030000 -#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c - static void setup_net_chip(void); /* diff --git a/board/karo/tx25/tx25.c b/board/karo/tx25/tx25.c index ce75468e38..307ffd0cbe 100644 --- a/board/karo/tx25/tx25.c +++ b/board/karo/tx25/tx25.c @@ -29,6 +29,7 @@ #include <asm/arch/imx-regs.h> #include <asm/arch/imx25-pinmux.h> #include <asm/gpio.h> +#include <asm/arch/sys_proto.h> static void mdelay(int n) { @@ -142,8 +143,6 @@ void tx25_fec_init(void) int board_init() { #ifdef CONFIG_MXC_UART - extern void mx25_uart1_init_pins(void); - mx25_uart1_init_pins(); #endif /* board id for linux */ diff --git a/board/logicpd/imx31_litekit/imx31_litekit.c b/board/logicpd/imx31_litekit/imx31_litekit.c index 09cc9c5b9c..7214008988 100644 --- a/board/logicpd/imx31_litekit/imx31_litekit.c +++ b/board/logicpd/imx31_litekit/imx31_litekit.c @@ -37,12 +37,6 @@ int dram_init(void) return 0; } -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; -} - int board_early_init_f(void) { __REG(CSCR_U(0)) = 0x0000cf03; /* CS0: Nor Flash */ @@ -76,7 +70,6 @@ int board_early_init_f(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_MX31LITE; /* board id for linux */ gd->bd->bi_boot_params = (0x80000100); /* adress of boot parameters */ return 0; diff --git a/board/overo/overo.c b/board/overo/overo.c index 4bbe1b87be..850dfeecd9 100644 --- a/board/overo/overo.c +++ b/board/overo/overo.c @@ -36,6 +36,7 @@ #include <asm/arch/mux.h> #include <asm/arch/mem.h> #include <asm/arch/sys_proto.h> +#include <asm/arch/omap_gpmc.h> #include <asm/gpio.h> #include <asm/mach-types.h> #include "overo.h" diff --git a/board/overo/overo.h b/board/overo/overo.h index 68e1243e9c..d394f902a1 100644 --- a/board/overo/overo.h +++ b/board/overo/overo.h @@ -33,15 +33,6 @@ const omap3_sysinfo sysinfo = { #endif }; -/* GPMC CS 5 connected to an SMSC LAN9221 ethernet controller */ -#define NET_LAN9221_GPMC_CONFIG1 0x00001000 -#define NET_LAN9221_GPMC_CONFIG2 0x00080701 -#define NET_LAN9221_GPMC_CONFIG3 0x00020201 -#define NET_LAN9221_GPMC_CONFIG4 0x08030703 -#define NET_LAN9221_GPMC_CONFIG5 0x00060908 -#define NET_LAN9221_GPMC_CONFIG6 0x87030000 -#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c - /* * IEN - Input Enable * IDIS - Input Disable @@ -128,7 +119,7 @@ const omap3_sysinfo sysinfo = { MUX_VAL(CP(GPMC_NCS6), (IEN | PTD | DIS | M0)) /*GPMC_nCS6*/\ MUX_VAL(CP(GPMC_NCS7), (IEN | PTU | EN | M0)) /*GPMC_nCS7*/\ MUX_VAL(CP(GPMC_NBE1), (IEN | PTD | DIS | M0)) /*GPMC_nCS3*/\ - MUX_VAL(CP(GPMC_CLK), (IDIS | PTU | EN | M0)) /*GPMC_CLK*/\ + MUX_VAL(CP(GPMC_CLK), (IEN | PTU | EN | M0)) /*GPMC_CLK*/\ MUX_VAL(CP(GPMC_NADV_ALE), (IDIS | PTD | DIS | M0)) /*GPMC_nADV_ALE*/\ MUX_VAL(CP(GPMC_NOE), (IDIS | PTD | DIS | M0)) /*GPMC_nOE*/\ MUX_VAL(CP(GPMC_NWE), (IDIS | PTD | DIS | M0)) /*GPMC_nWE*/\ diff --git a/board/sbc8240/Makefile b/board/sbc8240/Makefile deleted file mode 100644 index 12e4aa6880..0000000000 --- a/board/sbc8240/Makefile +++ /dev/null @@ -1,44 +0,0 @@ -# -# (C) Copyright 2001-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# See file CREDITS for list of people who contributed to this -# project. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).o - -COBJS = $(BOARD).o flash.o - -SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) -SOBJS := $(addprefix $(obj),$(SOBJS)) - -$(LIB): $(obj).depend $(OBJS) - $(call cmd_link_o_target, $(OBJS)) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/sbc8240/README b/board/sbc8240/README deleted file mode 100644 index 71595b4bff..0000000000 --- a/board/sbc8240/README +++ /dev/null @@ -1,140 +0,0 @@ -The supported features of the SBC8240/8245 board are: - 8240 or 8245 processor - 66MHz & 100MHz bus speed - Decrementer timer - 1 UART channel (Console channel) - 8240 Interrupt Controller - 8240 PCI bridge - 8240 Memory Controller - SDRAM (16, 64 MB Memory DIMM) - FLASH 512K On board - FLASH 4MB On board - - -Memory Map from CPU point of view: - - Start Size Access to - ----------------------------------------------------- - 0x00000000 64MB SDRAM DIMM - 0xFF000000 4MB On Board FLASH - 0xFFF00000 512K On Board FLASH or SRAM (Configured by jumper) - 0xFFE00000 8K EEPROM - 0xFFE80000 8Bit LED - 0xFFF80000 8Bit UART - - -Setting the board Jumpers & Switches: - - In order to get the board running with the default configuration the - jumpers need to be set as follows: - - General Jumpers: - ____________________________________________ - | Jumpers | Jumpers | Jumpers | - |-------------|--------------|---------------| - |JP1 1-2 | JP14 1-2 | JP27 1-2 | - |JP5 Open | JP15 1-2 | JP28 2-3 | - |JP8 1-2 | JP16 1-2 | JP33 Open | - |JP9 1-2 | JP17 1-2 | JP37 Close | - |JP10 1-2 | JP18 1-2 | | - |JP11 2-3 | JP19 1-2 | | - |JP12 1-2 | JP20 1-2 | | - |JP13 1-2 | JP25 Open | | - |_____________|______________|_______________| - - Bus speed Jumpers: - _________________________ - | 100MHz Bus | 66 MHz Bus | - |------------|------------| - | JP2 1-2 | JP2 1-2 | - | JP3 1-2 | JP3 2-3 | - | JP4 1-2 | JP4 2-3 | - | JP6 1-2 | JP6 2-3 | - | JP7 1-2 | JP7 1-2 | - |____________|____________| - - -U-Boot 1.1.2 (Jun 24 2004 - 17:01:04) - -CPU: MPC8240 Revision 1.1 at 247.500 MHz: 16 kB I-Cache 16 kB D-Cache -Board: sbc8240 Revision 255 Local Bus at 99 MHz -DRAM: 64 MB -FLASH: 512 kB - 00 11 8086 1229 0200 00 -In: serial -Out: serial -Err: serial -Net: i82559#0 - -Welcome to U-Boot for the sbc8240 - -Type ? or help to get on-line help - -Hit any key to stop autoboot: 0 -=> printenv -bootcmd=version;echo;tftpboot $loadaddr $loadfile;bootvx -bootdelay=5 -baudrate=9600 -ethaddr=DE:AD:BE:EF:01:01 -ipaddr=192.168.193.102 -preboot=echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type "? or help" to get on-line help;echo -netmask=255.255.255.248 -clocks_in_mhz=1 -bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei -ipaddr=192.168.193.102 -loadfile=vxWorks.st -loadaddr=0x01000000 -net_load=tftpboot $loadaddr $loadfile -serverip=192.168.193.99 -ethact=i82559#0 -stdin=serial -stdout=serial -stderr=serial - -Environment size: 631/16380 bytes -=> boot - -U-Boot 1.1.2 (Jun 24 2004 - 17:01:04) - -Using i82559#0 device -TFTP from server 192.168.193.99; our IP address is 192.168.193.102 -Filename 'vxWorks.st'. -Load address: 0x1000000 -Loading: ################################################################# - ################################################################# - ############################################################## -done -Bytes transferred = 979927 (ef3d7 hex) -## Ethernet MAC address not copied to NV RAM -Loading .text @ 0x00100000 (758848 bytes) -Loading .data @ 0x001b9440 (79904 bytes) -Clearing .bss @ 0x001ccc60 (20288 bytes) -## Using bootline (@ 0x4200): $fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 tn=sbc8240 o=fei -## Starting vxWorks at 0x00100000 ... - -Adding 2845 symbols for standalone. - - - ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] - ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] - ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] - ]]]]]]]]]]] ]]]] ]]]]]]]]]] ]] ]]]] (R) - ] ]]]]]]]]] ]]]]]] ]]]]]]]] ]] ]]]] - ]] ]]]]]]] ]]]]]]]] ]]]]]] ] ]] ]]]] - ]]] ]]]]] ] ]]] ] ]]]] ]]] ]]]]]]]]] ]]]] ]] ]]]] ]] ]]]]] - ]]]] ]]] ]] ] ]]] ]] ]]]]] ]]]]]] ]] ]]]]]]] ]]]] ]] ]]]] - ]]]]] ] ]]]] ]]]]] ]]]]]]]] ]]]] ]] ]]]] ]]]]]]] ]]]] - ]]]]]] ]]]]] ]]]]]] ] ]]]]] ]]]] ]] ]]]] ]]]]]]]] ]]]] - ]]]]]]] ]]]]] ] ]]]]]] ] ]]] ]]]] ]] ]]]] ]]]] ]]]] ]]]] - ]]]]]]]] ]]]]] ]]] ]]]]]]] ] ]]]]]]] ]]]] ]]]] ]]]] ]]]]] - ]]]]]]]]]]]]]]]]]]]]]]]]]]]]]] - ]]]]]]]]]]]]]]]]]]]]]]]]]]]]] Development System - ]]]]]]]]]]]]]]]]]]]]]]]]]]]] - ]]]]]]]]]]]]]]]]]]]]]]]]]]] VxWorks version 5.5.1 - ]]]]]]]]]]]]]]]]]]]]]]]]]] KERNEL: WIND version 2.6 - ]]]]]]]]]]]]]]]]]]]]]]]]] Copyright Wind River Systems, Inc., 1984-2003 - - CPU: MPC8240 -- Wind River BSP. SBC8240 Board. Processor #0. - Memory Size: 0x2000000. BSP version 1.2/28. - --> diff --git a/board/sbc8240/flash.c b/board/sbc8240/flash.c deleted file mode 100644 index a095753a41..0000000000 --- a/board/sbc8240/flash.c +++ /dev/null @@ -1,638 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * Modified 4/5/2001 - * Wait for completion of each sector erase command issued - * 4/5/2001 - * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com - */ - -#include <common.h> -#include <mpc824x.h> -#include <asm/processor.h> - -#if CONFIG_SYS_MAX_FLASH_BANKS != 1 -#error "CONFIG_SYS_MAX_FLASH_BANKS must be 1" -#endif -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */ - -/*----------------------------------------------------------------------- - * Functions - */ -static ulong flash_get_size (vu_long * addr, flash_info_t * info); -static int write_word (flash_info_t * info, ulong dest, ulong data); -static void flash_get_offsets (ulong base, flash_info_t * info); - -#define ADDR0 0x5555 -#define ADDR1 0x2aaa -#define FLASH_WORD_SIZE unsigned char - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init (void) -{ - unsigned long size_b0; - - /* Init: no FLASHes known */ - flash_info[0].flash_id = FLASH_UNKNOWN; - - /* Static FLASH Bank configuration here - FIXME XXX */ - - size_b0 = flash_get_size ((vu_long *) FLASH_BASE0_PRELIM, &flash_info[0]); - - if (flash_info[0].flash_id == FLASH_UNKNOWN) { - printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n", - size_b0, size_b0 << 20); - } - - /* Only one bank */ - /* Setup offsets */ - flash_get_offsets (FLASH_BASE0_PRELIM, &flash_info[0]); - - /* Monitor protection ON by default */ - (void) flash_protect (FLAG_PROTECT_SET, - FLASH_BASE0_PRELIM, - FLASH_BASE0_PRELIM + monitor_flash_len - 1, - &flash_info[0]); - flash_info[0].size = size_b0; - - return size_b0; -} - - -/*----------------------------------------------------------------------- - */ -static void flash_get_offsets (ulong base, flash_info_t * info) -{ - int i; - - /* set up sector start address table */ - if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) || - (info->flash_id == FLASH_AM040)) { - for (i = 0; i < info->sector_count; i++) - info->start[i] = base + (i * 0x00010000); - } else { - if (info->flash_id & FLASH_BTYPE) { - /* set sector offsets for bottom boot block type */ - info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for (i = 4; i < info->sector_count; i++) { - info->start[i] = - base + (i * 0x00010000) - 0x00030000; - } - } else { - /* set sector offsets for top boot block type */ - i = info->sector_count - 1; - info->start[i--] = base + info->size - 0x00004000; - info->start[i--] = base + info->size - 0x00006000; - info->start[i--] = base + info->size - 0x00008000; - for (; i >= 0; i--) { - info->start[i] = base + i * 0x00010000; - } - } - } -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t * info) -{ - int i; - int k; - int size; - int erased; - volatile unsigned long *flash; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch (info->flash_id & FLASH_VENDMASK) { - case FLASH_MAN_AMD: - printf ("AMD "); - break; - case FLASH_MAN_FUJ: - printf ("FUJITSU "); - break; - case FLASH_MAN_SST: - printf ("SST "); - break; - default: - printf ("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case FLASH_AM040: - printf ("AM29F040 (512 Kbit, uniform sector size)\n"); - break; - case FLASH_AM400B: - printf ("AM29LV400B (4 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM400T: - printf ("AM29LV400T (4 Mbit, top boot sector)\n"); - break; - case FLASH_AM800B: - printf ("AM29LV800B (8 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM800T: - printf ("AM29LV800T (8 Mbit, top boot sector)\n"); - break; - case FLASH_AM160B: - printf ("AM29LV160B (16 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM160T: - printf ("AM29LV160T (16 Mbit, top boot sector)\n"); - break; - case FLASH_AM320B: - printf ("AM29LV320B (32 Mbit, bottom boot sect)\n"); - break; - case FLASH_AM320T: - printf ("AM29LV320T (32 Mbit, top boot sector)\n"); - break; - case FLASH_SST800A: - printf ("SST39LF/VF800 (8 Mbit, uniform sector size)\n"); - break; - case FLASH_SST160A: - printf ("SST39LF/VF160 (16 Mbit, uniform sector size)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld KB in %d Sectors\n", - info->size >> 10, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i = 0; i < info->sector_count; ++i) { - /* - * Check if whole sector is erased - */ - if (i != (info->sector_count - 1)) - size = info->start[i + 1] - info->start[i]; - else - size = info->start[0] + info->size - info->start[i]; - erased = 1; - flash = (volatile unsigned long *) info->start[i]; - size = size >> 2; /* divide by 4 for longword access */ - for (k = 0; k < size; k++) { - if (*flash++ != 0xffffffff) { - erased = 0; - break; - } - } - - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s%s", - info->start[i], - erased ? " E" : " ", info->protect[i] ? "RO " : " " - ); - } - printf ("\n"); - return; -} - -/*----------------------------------------------------------------------- - */ - - -/*----------------------------------------------------------------------- - */ - -/* - * The following code cannot be run from FLASH! - */ -static ulong flash_get_size (vu_long * addr, flash_info_t * info) -{ - short i; - FLASH_WORD_SIZE value; - ulong base = (ulong) addr; - volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) addr; - - /* Write auto select command: read Manufacturer ID */ - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00900090; - - value = addr2[0]; - - switch (value) { - case (FLASH_WORD_SIZE) AMD_MANUFACT: - info->flash_id = FLASH_MAN_AMD; - break; - case (FLASH_WORD_SIZE) FUJ_MANUFACT: - info->flash_id = FLASH_MAN_FUJ; - break; - case (FLASH_WORD_SIZE) SST_MANUFACT: - info->flash_id = FLASH_MAN_SST; - break; - default: - info->flash_id = FLASH_UNKNOWN; - info->sector_count = 0; - info->size = 0; - return (0); /* no or unknown flash */ - } - - value = addr2[1]; /* device ID */ - - switch (value) { - case (FLASH_WORD_SIZE) AMD_ID_F040B: - info->flash_id += FLASH_AM040; - info->sector_count = 8; - info->size = 0x0080000; /* => 512 ko */ - break; - case (FLASH_WORD_SIZE) AMD_ID_LV040B: - info->flash_id += FLASH_AM040; - info->sector_count = 8; - info->size = 0x0080000; /* => 512 ko */ - break; - case (FLASH_WORD_SIZE) AMD_ID_LV400T: - info->flash_id += FLASH_AM400T; - info->sector_count = 11; - info->size = 0x00080000; - break; /* => 0.5 MB */ - - case (FLASH_WORD_SIZE) AMD_ID_LV400B: - info->flash_id += FLASH_AM400B; - info->sector_count = 11; - info->size = 0x00080000; - break; /* => 0.5 MB */ - - case (FLASH_WORD_SIZE) AMD_ID_LV800T: - info->flash_id += FLASH_AM800T; - info->sector_count = 19; - info->size = 0x00100000; - break; /* => 1 MB */ - - case (FLASH_WORD_SIZE) AMD_ID_LV800B: - info->flash_id += FLASH_AM800B; - info->sector_count = 19; - info->size = 0x00100000; - break; /* => 1 MB */ - - case (FLASH_WORD_SIZE) AMD_ID_LV160T: - info->flash_id += FLASH_AM160T; - info->sector_count = 35; - info->size = 0x00200000; - break; /* => 2 MB */ - - case (FLASH_WORD_SIZE) AMD_ID_LV160B: - info->flash_id += FLASH_AM160B; - info->sector_count = 35; - info->size = 0x00200000; - break; /* => 2 MB */ -#if 0 /* enable when device IDs are available */ - case (FLASH_WORD_SIZE) AMD_ID_LV320T: - info->flash_id += FLASH_AM320T; - info->sector_count = 67; - info->size = 0x00400000; - break; /* => 4 MB */ - - case (FLASH_WORD_SIZE) AMD_ID_LV320B: - info->flash_id += FLASH_AM320B; - info->sector_count = 67; - info->size = 0x00400000; - break; /* => 4 MB */ -#endif - case (FLASH_WORD_SIZE) SST_ID_xF800A: - info->flash_id += FLASH_SST800A; - info->sector_count = 16; - info->size = 0x00100000; - break; /* => 1 MB */ - - case (FLASH_WORD_SIZE) SST_ID_xF160A: - info->flash_id += FLASH_SST160A; - info->sector_count = 32; - info->size = 0x00200000; - break; /* => 2 MB */ - - default: - info->flash_id = FLASH_UNKNOWN; - return (0); /* => no or unknown flash */ - - } - - /* set up sector start address table */ - if (((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) || - (info->flash_id == FLASH_AM040)) { - for (i = 0; i < info->sector_count; i++) - info->start[i] = base + (i * 0x00010000); - } else { - if (info->flash_id & FLASH_BTYPE) { - /* set sector offsets for bottom boot block type */ - info->start[0] = base + 0x00000000; - info->start[1] = base + 0x00004000; - info->start[2] = base + 0x00006000; - info->start[3] = base + 0x00008000; - for (i = 4; i < info->sector_count; i++) { - info->start[i] = - base + (i * 0x00010000) - 0x00030000; - } - } else { - /* set sector offsets for top boot block type */ - i = info->sector_count - 1; - info->start[i--] = base + info->size - 0x00004000; - info->start[i--] = base + info->size - 0x00006000; - info->start[i--] = base + info->size - 0x00008000; - for (; i >= 0; i--) { - info->start[i] = base + i * 0x00010000; - } - } - } - - /* check for protected sectors */ - for (i = 0; i < info->sector_count; i++) { - /* read sector protection at sector address, (A7 .. A0) = 0x02 */ - /* D0 = 1 if protected */ - addr2 = (volatile FLASH_WORD_SIZE *) (info->start[i]); - if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST) - info->protect[i] = 0; - else - info->protect[i] = addr2[2] & 1; - } - - /* - * Prevent writes to uninitialized FLASH. - */ - if (info->flash_id != FLASH_UNKNOWN) { - addr2 = (FLASH_WORD_SIZE *) info->start[0]; - *addr2 = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ - } - - return (info->size); -} - -int wait_for_DQ7 (flash_info_t * info, int sect) -{ - ulong start, now, last; - volatile FLASH_WORD_SIZE *addr = - (FLASH_WORD_SIZE *) (info->start[sect]); - - start = get_timer (0); - last = start; - while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) != - (FLASH_WORD_SIZE) 0x00800080) { - if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - return -1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - putc ('.'); - last = now; - } - } - return 0; -} - -/*----------------------------------------------------------------------- - */ - -int flash_erase (flash_info_t * info, int s_first, int s_last) -{ - volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]); - volatile FLASH_WORD_SIZE *addr2; - int flag, prot, sect, l_sect; - int i; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("Can't erase unknown flash type - aborted\n"); - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; ++sect) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", prot); - } else { - printf ("\n"); - } - - l_sect = -1; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts (); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr2 = (FLASH_WORD_SIZE *) (info->start[sect]); - printf ("Erasing sector %p\n", addr2); /* CLH */ - - if ((info->flash_id & FLASH_VENDMASK) == - FLASH_MAN_SST) { - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[0] = (FLASH_WORD_SIZE) 0x00500050; /* block erase */ - for (i = 0; i < 50; i++) - udelay (1000); /* wait 1 ms */ - } else { - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080; - addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[0] = (FLASH_WORD_SIZE) 0x00300030; /* sector erase */ - } - l_sect = sect; - /* - * Wait for each sector to complete, it's more - * reliable. According to AMD Spec, you must - * issue all erase commands within a specified - * timeout. This has been seen to fail, especially - * if printf()s are included (for debug)!! - */ - wait_for_DQ7 (info, sect); - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts (); - - /* wait at least 80us - let's wait 1 ms */ - udelay (1000); - -#if 0 - /* - * We wait for the last triggered sector - */ - if (l_sect < 0) - goto DONE; - wait_for_DQ7 (info, l_sect); - - DONE: -#endif - /* reset to read mode */ - addr = (FLASH_WORD_SIZE *) info->start[0]; - addr[0] = (FLASH_WORD_SIZE) 0x00F000F0; /* reset bank */ - - printf (" done\n"); - return 0; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) -{ - ulong cp, wp, data; - int i, l, rc; - - wp = (addr & ~3); /* get lower word aligned address */ - - /* - * handle unaligned start bytes - */ - if ((l = addr - wp) != 0) { - data = 0; - for (i = 0, cp = wp; i < l; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - for (; i < 4 && cnt > 0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt == 0 && i < 4; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - if ((rc = write_word (info, wp, data)) != 0) { - return (rc); - } - wp += 4; - } - - /* - * handle word aligned part - */ - while (cnt >= 4) { - data = 0; - for (i = 0; i < 4; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_word (info, wp, data)) != 0) { - return (rc); - } - wp += 4; - cnt -= 4; - } - - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i < 4; ++i, ++cp) { - data = (data << 8) | (*(uchar *) cp); - } - - return (write_word (info, wp, data)); -} - -/*----------------------------------------------------------------------- - * Write a word to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_word (flash_info_t * info, ulong dest, ulong data) -{ - volatile FLASH_WORD_SIZE *addr2 = - (FLASH_WORD_SIZE *) (info->start[0]); - volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest; - volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data; - ulong start; - int i; - - /* Check if Flash is (sufficiently) erased */ - if ((*((volatile FLASH_WORD_SIZE *) dest) & - (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) { - return (2); - } - - for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) { - int flag; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts (); - - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA; - addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055; - addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00A000A0; - - dest2[i] = data2[i]; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts (); - - /* data polling for D7 */ - start = get_timer (0); - while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) != - (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) { - - if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - return (1); - } - } - } - - return (0); -} diff --git a/board/sbc8240/sbc8240.c b/board/sbc8240/sbc8240.c deleted file mode 100644 index 01abe26a42..0000000000 --- a/board/sbc8240/sbc8240.c +++ /dev/null @@ -1,111 +0,0 @@ -/* - * (C) Copyright 2001 - * Rob Taylor, Flying Pig Systems. robt@flyingpig.com. - * - * (C) Copyright 2001, 2002 - * Wolfgang Denk, DENX Software Engineering, <wd@denx.de> - - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <mpc824x.h> -#include <asm/processor.h> -#include <pci.h> -#include <netdev.h> - -DECLARE_GLOBAL_DATA_PTR; - -#define BOARD_REV_REG 0xFE80002B - -int checkboard (void) -{ - char revision = *(volatile char *)(BOARD_REV_REG); - char buf[32]; - - puts ("Board: sbc8240 "); - printf("Revision %d ", revision); - printf("Local Bus at %s MHz\n", strmhz(buf, gd->bus_clk)); - - return 0; -} - -phys_size_t initdram(int board_type) -{ - long size; - long new_bank0_end; - long mear1; - long emear1; - - size = get_ram_size(CONFIG_SYS_SDRAM_BASE, CONFIG_SYS_MAX_RAM_SIZE); - - new_bank0_end = size - 1; - mear1 = mpc824x_mpc107_getreg(MEAR1); - emear1 = mpc824x_mpc107_getreg(EMEAR1); - mear1 = (mear1 & 0xFFFFFF00) | - ((new_bank0_end & MICR_ADDR_MASK) >> MICR_ADDR_SHIFT); - emear1 = (emear1 & 0xFFFFFF00) | - ((new_bank0_end & MICR_ADDR_MASK) >> MICR_EADDR_SHIFT); - mpc824x_mpc107_setreg(MEAR1, mear1); - mpc824x_mpc107_setreg(EMEAR1, emear1); - - return (size); -} - -/* - * Initialize PCI Devices, report devices found. - */ -#ifndef CONFIG_PCI_PNP -static struct pci_config_table pci_sandpoint_config_table[] = { - { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, 0x0f, PCI_ANY_ID, - pci_cfgfunc_config_device, { PCI_ENET0_IOADDR, - PCI_ENET0_MEMADDR, - PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER }}, - - { } -}; -#endif - -struct pci_controller hose = { -#ifndef CONFIG_PCI_PNP - config_table: pci_sandpoint_config_table, -#endif -}; - -void pci_init_board(void) -{ - pci_mpc824x_init(&hose); -} - -#ifdef CONFIG_MISC_INIT_R -/* ------------------------------------------------------------------------- */ -int misc_init_r (void) -{ -#ifdef CONFIG_SYS_LED_BASE - *((unsigned char *) (CONFIG_SYS_LED_BASE)) = 0xFF; -#endif /* CONFIG_SYS_LED_BASE */ - - return (0); -} -#endif /* CONFIG_MISC_INIT_R */ - -int board_eth_init(bd_t *bis) -{ - return pci_eth_init(bis); -} diff --git a/board/sbc8260/flash.c b/board/sbc8260/flash.c deleted file mode 100644 index 645c67f430..0000000000 --- a/board/sbc8260/flash.c +++ /dev/null @@ -1,392 +0,0 @@ -/* - * (C) Copyright 2000 - * Marius Groeger <mgroeger@sysgo.de> - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * - * (C) Copyright 2000 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Flash Routines for AMD 29F080B devices - * - *-------------------------------------------------------------------- - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <mpc8xx.h> - -flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; - -/*----------------------------------------------------------------------- - * Functions - */ - -static ulong flash_get_size (vu_long *addr, flash_info_t *info); -static int write_word (flash_info_t *info, ulong dest, ulong data); - -/*----------------------------------------------------------------------- - */ - -unsigned long flash_init (void) -{ - unsigned long size; - int i; - - /* Init: no FLASHes known */ - for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) { - flash_info[i].flash_id = FLASH_UNKNOWN; - } - - /* for now, only support the 4 MB Flash SIMM */ - size = flash_get_size((vu_long *)CONFIG_SYS_FLASH0_BASE, &flash_info[0]); - - /* - * protect monitor and environment sectors - */ - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH0_BASE - flash_protect(FLAG_PROTECT_SET, - CONFIG_SYS_MONITOR_BASE, - CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1, - &flash_info[0]); -#endif - -#if defined(CONFIG_ENV_IS_IN_FLASH) && defined(CONFIG_ENV_ADDR) -# ifndef CONFIG_ENV_SIZE -# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -# endif - flash_protect(FLAG_PROTECT_SET, - CONFIG_ENV_ADDR, - CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1, - &flash_info[0]); -#endif - - return /*size*/ (CONFIG_SYS_FLASH0_SIZE * 1024 * 1024); -} - -/*----------------------------------------------------------------------- - */ -void flash_print_info (flash_info_t *info) -{ - int i; - - if (info->flash_id == FLASH_UNKNOWN) { - printf ("missing or unknown FLASH type\n"); - return; - } - - switch ((info->flash_id >> 16) & 0xff) { - case 0x1: - printf ("AMD "); - break; - default: - printf ("Unknown Vendor "); - break; - } - - switch (info->flash_id & FLASH_TYPEMASK) { - case AMD_ID_F040B: - printf ("AM29F040B (4 Mbit)\n"); - break; - case AMD_ID_F080B: - printf ("AM29F080B (8 Mbit)\n"); - break; - default: - printf ("Unknown Chip Type\n"); - break; - } - - printf (" Size: %ld MB in %d Sectors\n", - info->size >> 20, info->sector_count); - - printf (" Sector Start Addresses:"); - for (i=0; i<info->sector_count; ++i) { - if ((i % 5) == 0) - printf ("\n "); - printf (" %08lX%s", - info->start[i], - info->protect[i] ? " (RO)" : " " - ); - } - printf ("\n"); - return; -} - -/* - * The following code cannot be run from FLASH! - */ - -static ulong flash_get_size (vu_long *addr, flash_info_t *info) -{ - short i; - vu_long vendor, devid; - ulong base = (ulong)addr; - -/* printf("addr = %08lx\n", (unsigned long)addr); */ - - /* Reset and Write auto select command: read Manufacturer ID */ - addr[0] = 0xf0f0f0f0; - addr[0x0555] = 0xAAAAAAAA; - addr[0x02AA] = 0x55555555; - addr[0x0555] = 0x90909090; - udelay (1000); - - vendor = addr[0]; -/* printf("vendor = %08lx\n", vendor); */ - if (vendor != 0x01010101) { - info->size = 0; - goto out; - } - - devid = addr[1]; -/* printf("devid = %08lx\n", devid); */ - - if ((devid & 0xff) == AMD_ID_F080B) { - info->flash_id = (vendor & 0xff) << 16 | AMD_ID_F080B; - /* we have 16 sectors with 64KB each x 4 */ - info->sector_count = 16; - info->size = 4 * info->sector_count * 64*1024; - } - else { - info->size = 0; - goto out; - } - - /* check for protected sectors */ - for (i = 0; i < info->sector_count; i++) { - /* sector base address */ - info->start[i] = base + i * (info->size / info->sector_count); - /* read sector protection at sector address, (A7 .. A0) = 0x02 */ - /* D0 = 1 if protected */ - addr = (volatile unsigned long *)(info->start[i]); - info->protect[i] = addr[2] & 1; - } - - /* reset command */ - addr = (vu_long *)info->start[0]; - -out: - addr[0] = 0xf0f0f0f0; - - return info->size; -} - - -/*----------------------------------------------------------------------- - */ - -int flash_erase (flash_info_t *info, int s_first, int s_last) -{ - vu_long *addr = (vu_long*)(info->start[0]); - int flag, prot, sect, l_sect; - ulong start, now, last; - - if ((s_first < 0) || (s_first > s_last)) { - if (info->flash_id == FLASH_UNKNOWN) { - printf ("- missing\n"); - } else { - printf ("- no sectors to erase\n"); - } - return 1; - } - - prot = 0; - for (sect = s_first; sect <= s_last; sect++) { - if (info->protect[sect]) { - prot++; - } - } - - if (prot) { - printf ("- Warning: %d protected sectors will not be erased!\n", - prot); - } else { - printf ("\n"); - } - - l_sect = -1; - - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - addr[0x0555] = 0xAAAAAAAA; - addr[0x02AA] = 0x55555555; - addr[0x0555] = 0x80808080; - addr[0x0555] = 0xAAAAAAAA; - addr[0x02AA] = 0x55555555; - udelay (100); - - /* Start erase on unprotected sectors */ - for (sect = s_first; sect<=s_last; sect++) { - if (info->protect[sect] == 0) { /* not protected */ - addr = (vu_long*)(info->start[sect]); - addr[0] = 0x30303030; - l_sect = sect; - } - } - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* wait at least 80us - let's wait 1 ms */ - udelay (1000); - - /* - * We wait for the last triggered sector - */ - if (l_sect < 0) - goto DONE; - - start = get_timer (0); - last = start; - addr = (vu_long*)(info->start[l_sect]); - while ((addr[0] & 0x80808080) != 0x80808080) { - if ((now = get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) { - printf ("Timeout\n"); - return 1; - } - /* show that we're waiting */ - if ((now - last) > 1000) { /* every second */ - serial_putc ('.'); - last = now; - } - } - - DONE: - /* reset to read mode */ - addr = (volatile unsigned long *)info->start[0]; - addr[0] = 0xF0F0F0F0; /* reset bank */ - - printf (" done\n"); - return 0; -} - -/*----------------------------------------------------------------------- - * Copy memory to flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ - -int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt) -{ - ulong cp, wp, data; - int i, l, rc; - - wp = (addr & ~3); /* get lower word aligned address */ - - /* - * handle unaligned start bytes - */ - if ((l = addr - wp) != 0) { - data = 0; - for (i=0, cp=wp; i<l; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - for (; i<4 && cnt>0; ++i) { - data = (data << 8) | *src++; - --cnt; - ++cp; - } - for (; cnt==0 && i<4; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - - if ((rc = write_word(info, wp, data)) != 0) { - return (rc); - } - wp += 4; - } - - /* - * handle word aligned part - */ - while (cnt >= 4) { - data = 0; - for (i=0; i<4; ++i) { - data = (data << 8) | *src++; - } - if ((rc = write_word(info, wp, data)) != 0) { - return (rc); - } - wp += 4; - cnt -= 4; - } - - if (cnt == 0) { - return (0); - } - - /* - * handle unaligned tail bytes - */ - data = 0; - for (i=0, cp=wp; i<4 && cnt>0; ++i, ++cp) { - data = (data << 8) | *src++; - --cnt; - } - for (; i<4; ++i, ++cp) { - data = (data << 8) | (*(uchar *)cp); - } - - return (write_word(info, wp, data)); -} - -/*----------------------------------------------------------------------- - * Write a word to Flash, returns: - * 0 - OK - * 1 - write timeout - * 2 - Flash not erased - */ -static int write_word (flash_info_t *info, ulong dest, ulong data) -{ - vu_long *addr = (vu_long*)(info->start[0]); - ulong start; - int flag; - - /* Check if Flash is (sufficiently) erased */ - if ((*((vu_long *)dest) & data) != data) { - return (2); - } - /* Disable interrupts which might cause a timeout here */ - flag = disable_interrupts(); - - addr[0x0555] = 0xAAAAAAAA; - addr[0x02AA] = 0x55555555; - addr[0x0555] = 0xA0A0A0A0; - - *((vu_long *)dest) = data; - - /* re-enable interrupts if necessary */ - if (flag) - enable_interrupts(); - - /* data polling for D7 */ - start = get_timer (0); - while ((*((vu_long *)dest) & 0x80808080) != (data & 0x80808080)) { - if (get_timer(start) > CONFIG_SYS_FLASH_WRITE_TOUT) { - return (1); - } - } - return (0); -} - -/*----------------------------------------------------------------------- - */ diff --git a/board/sbc8260/sbc8260.c b/board/sbc8260/sbc8260.c deleted file mode 100644 index 33ce1a4ee3..0000000000 --- a/board/sbc8260/sbc8260.c +++ /dev/null @@ -1,289 +0,0 @@ -/* - * (C) Copyright 2000 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * (C) Copyright 2001 - * Advent Networks, Inc. <http://www.adventnetworks.com> - * Jay Monkman <jtm@smoothsmoothie.com> - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include <common.h> -#include <ioports.h> -#include <mpc8260.h> - -/* - * I/O Port configuration table - * - * if conf is 1, then that port pin will be configured at boot time - * according to the five values podr/pdir/ppar/psor/pdat for that entry - */ - -const iop_conf_t iop_conf_tab[4][32] = { - - /* Port A configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PA31 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 *ATMTXEN */ - /* PA30 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTCA */ - /* PA29 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTSOC */ - /* PA28 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 *ATMRXEN */ - /* PA27 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRSOC */ - /* PA26 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRCA */ - /* PA25 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */ - /* PA24 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */ - /* PA23 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */ - /* PA22 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */ - /* PA21 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */ - /* PA20 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */ - /* PA19 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */ - /* PA18 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */ - /* PA17 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[7] */ - /* PA16 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[6] */ - /* PA15 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[5] */ - /* PA14 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[4] */ - /* PA13 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[3] */ - /* PA12 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[2] */ - /* PA11 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[1] */ - /* PA10 */ { 1, 0, 0, 1, 0, 0 }, /* FCC1 ATMRXD[0] */ - /* PA9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC2 TXD */ - /* PA8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC2 RXD */ - /* PA7 */ { 1, 0, 0, 1, 0, 0 }, /* PA7 */ - /* PA6 */ { 1, 0, 0, 1, 0, 0 }, /* PA6 */ - /* PA5 */ { 1, 0, 0, 1, 0, 0 }, /* PA5 */ - /* PA4 */ { 1, 0, 0, 1, 0, 0 }, /* PA4 */ - /* PA3 */ { 1, 0, 0, 1, 0, 0 }, /* PA3 */ - /* PA2 */ { 1, 0, 0, 1, 0, 0 }, /* PA2 */ - /* PA1 */ { 1, 0, 0, 1, 0, 0 }, /* PA1 */ - /* PA0 */ { 1, 0, 0, 1, 0, 0 } /* PA0 */ - }, - - /* Port B configuration */ - { /* conf ppar psor pdir podr pdat */ - /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */ - /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */ - /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */ - /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */ - /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */ - /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */ - /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */ - /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */ - /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */ - /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */ - /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */ - /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */ - /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */ - /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */ - /* PB17 */ { 1, 0, 0, 1, 0, 0 }, /* PB17 */ - /* PB16 */ { 1, 0, 0, 1, 0, 0 }, /* PB16 */ - /* PB15 */ { 1, 0, 0, 1, 0, 0 }, /* PB15 */ - /* PB14 */ { 1, 0, 0, 1, 0, 0 }, /* PB14 */ - /* PB13 */ { 1, 0, 0, 1, 0, 0 }, /* PB13 */ - /* PB12 */ { 1, 0, 0, 1, 0, 0 }, /* PB12 */ - /* PB11 */ { 1, 0, 0, 1, 0, 0 }, /* PB11 */ - /* PB10 */ { 1, 0, 0, 1, 0, 0 }, /* PB10 */ - /* PB9 */ { 1, 0, 0, 1, 0, 0 }, /* PB9 */ - /* PB8 */ { 1, 0, 0, 1, 0, 0 }, /* PB8 */ - /* PB7 */ { 1, 0, 0, 1, 0, 0 }, /* PB7 */ - /* PB6 */ { 1, 0, 0, 1, 0, 0 }, /* PB6 */ - /* PB5 */ { 1, 0, 0, 1, 0, 0 }, /* PB5 */ - /* PB4 */ { 1, 0, 0, 1, 0, 0 }, /* PB4 */ - /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - }, - - /* Port C */ - { /* conf ppar psor pdir podr pdat */ - /* PC31 */ { 1, 0, 0, 1, 0, 0 }, /* PC31 */ - /* PC30 */ { 1, 0, 0, 1, 0, 0 }, /* PC30 */ - /* PC29 */ { 1, 1, 1, 0, 0, 0 }, /* SCC1 EN *CLSN */ - /* PC28 */ { 1, 0, 0, 1, 0, 0 }, /* PC28 */ - /* PC27 */ { 1, 0, 0, 1, 0, 0 }, /* PC27 */ - /* PC26 */ { 1, 0, 0, 1, 0, 0 }, /* PC26 */ - /* PC25 */ { 1, 0, 0, 1, 0, 0 }, /* PC25 */ - /* PC24 */ { 1, 0, 0, 1, 0, 0 }, /* PC24 */ - /* PC23 */ { 1, 1, 0, 1, 0, 0 }, /* ATMTFCLK */ - /* PC22 */ { 1, 1, 0, 0, 0, 0 }, /* ATMRFCLK */ - /* PC21 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */ - /* PC20 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */ - /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_CLK */ - /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII TX_CLK */ - /* PC17 */ { 1, 0, 0, 1, 0, 0 }, /* PC17 */ - /* PC16 */ { 1, 0, 0, 1, 0, 0 }, /* PC16 */ - /* PC15 */ { 1, 0, 0, 1, 0, 0 }, /* PC15 */ - /* PC14 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN *CD */ - /* PC13 */ { 1, 0, 0, 1, 0, 0 }, /* PC13 */ - /* PC12 */ { 1, 0, 0, 1, 0, 0 }, /* PC12 */ - /* PC11 */ { 1, 0, 0, 1, 0, 0 }, /* PC11 */ - /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MDC */ - /* PC9 */ { 1, 0, 0, 1, 0, 0 }, /* FCC2 MDIO */ - /* PC8 */ { 1, 0, 0, 1, 0, 0 }, /* PC8 */ - /* PC7 */ { 1, 0, 0, 1, 0, 0 }, /* PC7 */ - /* PC6 */ { 1, 0, 0, 1, 0, 0 }, /* PC6 */ - /* PC5 */ { 1, 0, 0, 1, 0, 0 }, /* PC5 */ - /* PC4 */ { 1, 0, 0, 1, 0, 0 }, /* PC4 */ - /* PC3 */ { 1, 0, 0, 1, 0, 0 }, /* PC3 */ - /* PC2 */ { 1, 0, 0, 1, 0, 1 }, /* ENET FDE */ - /* PC1 */ { 1, 0, 0, 1, 0, 0 }, /* ENET DSQE */ - /* PC0 */ { 1, 0, 0, 1, 0, 0 }, /* ENET LBK */ - }, - - /* Port D */ - { /* conf ppar psor pdir podr pdat */ - /* PD31 */ { 1, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */ - /* PD30 */ { 1, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */ - /* PD29 */ { 1, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */ - /* PD28 */ { 1, 0, 0, 1, 0, 0 }, /* PD28 */ - /* PD27 */ { 1, 0, 0, 1, 0, 0 }, /* PD27 */ - /* PD26 */ { 1, 0, 0, 1, 0, 0 }, /* PD26 */ - /* PD25 */ { 1, 0, 0, 1, 0, 0 }, /* PD25 */ - /* PD24 */ { 1, 0, 0, 1, 0, 0 }, /* PD24 */ - /* PD23 */ { 1, 0, 0, 1, 0, 0 }, /* PD23 */ - /* PD22 */ { 1, 0, 0, 1, 0, 0 }, /* PD22 */ - /* PD21 */ { 1, 0, 0, 1, 0, 0 }, /* PD21 */ - /* PD20 */ { 1, 0, 0, 1, 0, 0 }, /* PD20 */ - /* PD19 */ { 1, 0, 0, 1, 0, 0 }, /* PD19 */ - /* PD18 */ { 1, 0, 0, 1, 0, 0 }, /* PD18 */ - /* PD17 */ { 1, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */ - /* PD16 */ { 1, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */ -#if defined(CONFIG_SOFT_I2C) - /* PD15 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SDA */ - /* PD14 */ { 1, 0, 0, 1, 1, 1 }, /* I2C SCL */ -#else -#if defined(CONFIG_HARD_I2C) - /* PD15 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SDA */ - /* PD14 */ { 1, 1, 1, 0, 1, 0 }, /* I2C SCL */ -#else /* normal I/O port pins */ - /* PD15 */ { 1, 0, 0, 1, 0, 0 }, /* I2C SDA */ - /* PD14 */ { 1, 0, 0, 1, 0, 0 }, /* I2C SCL */ -#endif -#endif - /* PD13 */ { 1, 0, 0, 0, 0, 0 }, /* PD13 */ - /* PD12 */ { 1, 0, 0, 0, 0, 0 }, /* PD12 */ - /* PD11 */ { 1, 0, 0, 0, 0, 0 }, /* PD11 */ - /* PD10 */ { 1, 0, 0, 0, 0, 0 }, /* PD10 */ - /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */ - /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */ - /* PD7 */ { 1, 0, 0, 1, 0, 1 }, /* PD7 */ - /* PD6 */ { 1, 0, 0, 1, 0, 1 }, /* PD6 */ - /* PD5 */ { 1, 0, 0, 1, 0, 1 }, /* PD5 */ - /* PD4 */ { 1, 0, 0, 1, 0, 1 }, /* PD4 */ - /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */ - /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */ - } -}; - -/* ------------------------------------------------------------------------- */ - -/* - * Check Board Identity: - */ - -int checkboard (void) -{ - puts ("Board: EST SBC8260\n"); - return 0; -} - -/* ------------------------------------------------------------------------- */ - -phys_size_t initdram (int board_type) -{ - volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - volatile memctl8260_t *memctl = &immap->im_memctl; - volatile uchar c = 0, *ramaddr = (uchar *) (CONFIG_SYS_SDRAM_BASE + 0x8); - ulong psdmr = CONFIG_SYS_PSDMR; - int i; - - /* - * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35): - * - * "At system reset, initialization software must set up the - * programmable parameters in the memory controller banks registers - * (ORx, BRx, P/LSDMR). After all memory parameters are configured, - * system software should execute the following initialization sequence - * for each SDRAM device. - * - * 1. Issue a PRECHARGE-ALL-BANKS command - * 2. Issue eight CBR REFRESH commands - * 3. Issue a MODE-SET command to initialize the mode register - * - * The initial commands are executed by setting P/LSDMR[OP] and - * accessing the SDRAM with a single-byte transaction." - * - * The appropriate BRx/ORx registers have already been set when we - * get here. The SDRAM can be accessed at the address CONFIG_SYS_SDRAM_BASE. - */ - - memctl->memc_psrt = CONFIG_SYS_PSRT; - memctl->memc_mptpr = CONFIG_SYS_MPTPR; - - memctl->memc_psdmr = psdmr | PSDMR_OP_PREA; - *ramaddr = c; - - memctl->memc_psdmr = psdmr | PSDMR_OP_CBRR; - for (i = 0; i < 8; i++) - *ramaddr = c; - - memctl->memc_psdmr = psdmr | PSDMR_OP_MRW; - *ramaddr = c; - - memctl->memc_psdmr = psdmr | PSDMR_OP_NORM | PSDMR_RFEN; - *ramaddr = c; - - /* return total ram size */ - return (CONFIG_SYS_SDRAM0_SIZE * 1024 * 1024); -} - -#ifdef CONFIG_MISC_INIT_R -/* ------------------------------------------------------------------------- */ -int misc_init_r (void) -{ -#ifdef CONFIG_SYS_LED_BASE - uchar ds = *(unsigned char *) (CONFIG_SYS_LED_BASE + 1); - uchar ss; - uchar tmp[64]; - int res; - - if ((ds != 0) && (ds != 0xff)) { - res = getenv_f("ethaddr", tmp, sizeof (tmp)); - if (res > 0) { - ss = ((ds >> 4) & 0x0f); - ss += ss < 0x0a ? '0' : ('a' - 10); - tmp[15] = ss; - - ss = (ds & 0x0f); - ss += ss < 0x0a ? '0' : ('a' - 10); - tmp[16] = ss; - - tmp[17] = '\0'; - setenv ("ethaddr", tmp); - /* set the led to show the address */ - *((unsigned char *) (CONFIG_SYS_LED_BASE + 1)) = ds; - } - } -#endif /* CONFIG_SYS_LED_BASE */ - return (0); -} -#endif /* CONFIG_MISC_INIT_R */ diff --git a/board/syteco/zmx25/zmx25.c b/board/syteco/zmx25/zmx25.c index 893adc6bd5..a89ee1a086 100644 --- a/board/syteco/zmx25/zmx25.c +++ b/board/syteco/zmx25/zmx25.c @@ -117,8 +117,6 @@ int board_init() writel(input_select1, &inputselect->i2c3_ipp_sda_in); /* I2C3 SDA */ writel(input_select2, &inputselect->i2c3_ipp_scl_in); /* I2C3 SCL */ - /* board id for linux */ - gd->bd->bi_arch_number = MACH_TYPE_ZMX25; gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; return 0; @@ -188,9 +186,3 @@ int dram_init(void) PHYS_SDRAM_SIZE); return 0; } - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM; - gd->bd->bi_dram[0].size = gd->ram_size; -} diff --git a/board/timll/devkit8000/devkit8000.c b/board/timll/devkit8000/devkit8000.c index 533af5a60a..f50d113347 100644 --- a/board/timll/devkit8000/devkit8000.c +++ b/board/timll/devkit8000/devkit8000.c @@ -128,7 +128,7 @@ int board_mmc_init(bd_t *bis) } #endif -#ifdef CONFIG_DRIVER_DM9000 +#if defined(CONFIG_DRIVER_DM9000) & !defined(CONFIG_SPL_BUILD) /* * Routine: board_eth_init * Description: Setting up the Ethernet hardware. diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c index 17a25587d6..ebca7b6f36 100644 --- a/board/ttcontrol/vision2/vision2.c +++ b/board/ttcontrol/vision2/vision2.c @@ -653,7 +653,6 @@ void lcd_enable(void) int board_init(void) { - gd->bd->bi_arch_number = MACH_TYPE_TTC_VISION2; /* board id for linux */ /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; |
