diff options
Diffstat (limited to 'board/ti/omap1510inn/omap1510innovator.c')
| -rw-r--r-- | board/ti/omap1510inn/omap1510innovator.c | 125 |
1 files changed, 0 insertions, 125 deletions
diff --git a/board/ti/omap1510inn/omap1510innovator.c b/board/ti/omap1510inn/omap1510innovator.c deleted file mode 100644 index a2a33a050b..0000000000 --- a/board/ti/omap1510inn/omap1510innovator.c +++ /dev/null @@ -1,125 +0,0 @@ -/* - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH <www.elinos.com> - * Marius Groeger <mgroeger@sysgo.de> - * - * (C) Copyright 2002 - * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> - * - * (C) Copyright 2003 - * Texas Instruments, <www.ti.com> - * Kshitij Gupta <Kshitij@ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <netdev.h> - -DECLARE_GLOBAL_DATA_PTR; - -static void flash__init (void); -static void ether__init (void); - -static inline void delay (unsigned long loops) -{ - __asm__ volatile ("1:\n" - "subs %0, %1, #1\n" - "bne 1b":"=r" (loops):"0" (loops)); -} - -/* - * Miscellaneous platform dependent initialisations - */ - -int board_init (void) -{ - /* arch number of OMAP 1510-Board */ - gd->bd->bi_arch_number = MACH_TYPE_OMAP_INNOVATOR; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = 0x10000100; - -/* kk - this speeds up your boot a quite a bit. However to make it - * work, you need make sure your kernel startup flush bug is fixed. - * ... rkw ... - */ - icache_enable (); - - flash__init (); - ether__init (); - return 0; -} - - -int misc_init_r (void) -{ - /* volatile ushort *gdir = (ushort *) (GPIO_DIR_CONTROL_REG); */ - /* volatile ushort *mdir = (ushort *) (MPUIO_DIR_CONTROL_REG); */ - - /* setup gpio direction to match board (no floats!) */ - /**gdir = 0xCFF9; */ - /**mdir = 0x103F; */ - - return (0); -} - -/****************************** - Routine: - Description: -******************************/ -static void flash__init (void) -{ -#define CS0_CHIP_SELECT_REG 0xfffecc10 -#define CS3_CHIP_SELECT_REG 0xfffecc1c -#define EMIFS_GlB_Config_REG 0xfffecc0c - - { - unsigned int regval; - - regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG); - regval = regval | 0x0001; /* Turn off write protection for flash devices. */ - if (regval & 0x0002) { - regval = regval & 0xfffd; /* Swap CS0 and CS3 so that flash is visible at 0x0 and eeprom at 0x0c000000. */ - /* If, instead, you want to reference flash at 0x0c000000, then it seemed the following were necessary. */ - /* *((volatile unsigned int *)CS0_CHIP_SELECT_REG) = 0x202090; / * Overrides head.S setting of 0x212090 */ - /* *((volatile unsigned int *)CS3_CHIP_SELECT_REG) = 0x202090; / * Let's flash chips be fully functional. */ - } - *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval; - } -} - - -/****************************** - Routine: - Description: -******************************/ -static void ether__init (void) -{ -#define ETH_CONTROL_REG 0x0800000b - /* take the Ethernet controller out of reset and wait - * for the EEPROM load to complete. - */ - *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01; - udelay (3); -} - - -int dram_init (void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - - return 0; -} - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_LAN91C96 - rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE); -#endif - return rc; -} -#endif |
