diff options
Diffstat (limited to 'board/keymile/km_arm/km_arm.c')
| -rw-r--r-- | board/keymile/km_arm/km_arm.c | 152 |
1 files changed, 80 insertions, 72 deletions
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index 9e9940c51f..2b2ca39376 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -33,6 +33,7 @@ #include <nand.h> #include <netdev.h> #include <miiphy.h> +#include <spi.h> #include <asm/io.h> #include <asm/arch/cpu.h> #include <asm/arch/kirkwood.h> @@ -113,7 +114,7 @@ u32 kwmpp_config[] = { 0 }; -#if defined(CONFIG_MGCOGE3UN) +#if defined(CONFIG_KM_MGCOGE3UN) /* * Wait for startup OK from mgcoge3ne */ @@ -133,10 +134,10 @@ int startup_allowed(void) } #endif -#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2)) +#if (defined(CONFIG_KM_PIGGY4_88E6061)|defined(CONFIG_KM_PIGGY4_88E6352)) /* - * These two boards have always ethernet present. Its connected to the mv - * switch. + * All boards with PIGGY4 connected via a simple switch have ethernet always + * present. */ int ethernet_present(void) { @@ -201,7 +202,7 @@ int misc_init_r(void) printf("Overwriting MACH_TYPE with %d!!!\n", mach_type); gd->bd->bi_arch_number = mach_type; } -#if defined(CONFIG_MGCOGE3UN) +#if defined(CONFIG_KM_MGCOGE3UN) char *wait_for_ne; wait_for_ne = getenv("waitforne"); if (wait_for_ne != NULL) { @@ -242,90 +243,93 @@ int misc_init_r(void) int board_early_init_f(void) { +#if defined(CONFIG_SOFT_I2C) u32 tmp; - kirkwood_mpp_conf(kwmpp_config); + /* set the 2 bitbang i2c pins as output gpios */ + tmp = readl(KW_GPIO0_BASE + 4); + writel(tmp & (~KM_KIRKWOOD_SOFT_I2C_GPIOS) , KW_GPIO0_BASE + 4); +#endif + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ /* - * The FLASH_GPIO_PIN switches between using a + * arch number of board + */ + gd->bd->bi_arch_number = MACH_TYPE_KM_KIRKWOOD; + + /* address of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + /* + * The KM_FLASH_GPIO_PIN switches between using a * NAND or a SPI FLASH. Set this pin on start * to NAND mode. */ - tmp = readl(KW_GPIO0_BASE); - writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE); - tmp = readl(KW_GPIO0_BASE + 4); - writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE + 4); + kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1); + kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1); #if defined(CONFIG_SOFT_I2C) - /* init the GPIO for I2C Bitbang driver */ + /* + * Reinit the GPIO for I2C Bitbang driver so that the now + * available gpio framework is consistent. The calls to + * direction output in are not necessary, they are already done in + * board_early_init_f + */ kw_gpio_set_valid(KM_KIRKWOOD_SDA_PIN, 1); kw_gpio_set_valid(KM_KIRKWOOD_SCL_PIN, 1); - kw_gpio_direction_output(KM_KIRKWOOD_SDA_PIN, 0); - kw_gpio_direction_output(KM_KIRKWOOD_SCL_PIN, 0); #endif + #if defined(CONFIG_SYS_EEPROM_WREN) kw_gpio_set_valid(KM_KIRKWOOD_ENV_WP, 38); kw_gpio_direction_output(KM_KIRKWOOD_ENV_WP, 1); #endif -#if defined(CONFIG_KM_RECONFIG_XLX) - /* trigger the reconfiguration of the xilinx fpga */ - kw_gpio_set_valid(KM_XLX_PROGRAM_B_PIN, 1); - kw_gpio_direction_output(KM_XLX_PROGRAM_B_PIN, 0); - kw_gpio_direction_input(KM_XLX_PROGRAM_B_PIN); + +#if defined(CONFIG_KM_FPGA_CONFIG) + trigger_fpga_config(); #endif + return 0; } -int board_init(void) +int board_late_init(void) { - /* address of boot parameters */ - gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; +#if defined(CONFIG_KMCOGE5UN) +/* I/O pin to erase flash RGPP09 = MPP43 */ +#define KM_FLASH_ERASE_ENABLE 43 + u8 dip_switch = kw_gpio_get_value(KM_FLASH_ERASE_ENABLE); + + /* if pin 1 do full erase */ + if (dip_switch != 0) { + /* start bootloader */ + puts("DIP: Enabled\n"); + setenv("actual_bank", "0"); + } +#endif +#if defined(CONFIG_KM_FPGA_CONFIG) + wait_for_fpga_config(); + fpga_reset(); + toggle_eeprom_spi_bus(); +#endif return 0; } -#if defined(CONFIG_CMD_SF) -int do_spi_toggle(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +int board_spi_claim_bus(struct spi_slave *slave) { - u32 tmp; - if (argc < 2) - return cmd_usage(cmdtp); - - if ((strcmp(argv[1], "off") == 0)) { - printf("SPI FLASH disabled, NAND enabled\n"); - /* Multi-Purpose Pins Functionality configuration */ - kwmpp_config[0] = MPP0_NF_IO2; - kwmpp_config[1] = MPP1_NF_IO3; - kwmpp_config[2] = MPP2_NF_IO4; - kwmpp_config[3] = MPP3_NF_IO5; - - kirkwood_mpp_conf(kwmpp_config); - tmp = readl(KW_GPIO0_BASE); - writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE); - } else if ((strcmp(argv[1], "on") == 0)) { - printf("SPI FLASH enabled, NAND disabled\n"); - /* Multi-Purpose Pins Functionality configuration */ - kwmpp_config[0] = MPP0_SPI_SCn; - kwmpp_config[1] = MPP1_SPI_MOSI; - kwmpp_config[2] = MPP2_SPI_SCK; - kwmpp_config[3] = MPP3_SPI_MISO; - - kirkwood_mpp_conf(kwmpp_config); - tmp = readl(KW_GPIO0_BASE); - writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE); - } else { - return cmd_usage(cmdtp); - } + kw_gpio_set_value(KM_FLASH_GPIO_PIN, 0); return 0; } -U_BOOT_CMD( - spitoggle, 2, 0, do_spi_toggle, - "En-/disable SPI FLASH access", - "<on|off> - Enable (on) or disable (off) SPI FLASH access\n" - ); -#endif +void board_spi_release_bus(struct spi_slave *slave) +{ + kw_gpio_set_value(KM_FLASH_GPIO_PIN, 1); +} int dram_init(void) { @@ -347,15 +351,15 @@ void dram_init_banksize(void) } } -#if (defined(CONFIG_MGCOGE3UN)|defined(CONFIG_PORTL2)) +#if (defined(CONFIG_KM_PIGGY4_88E6061)) -#define PHY_LED_SEL 0x18 -#define PHY_LED0_LINK (0x5) -#define PHY_LED1_ACT (0x8<<4) -#define PHY_LED2_INT (0xe<<8) -#define PHY_SPEC_CTRL 0x1c +#define PHY_LED_SEL_REG 0x18 +#define PHY_LED0_LINK (0x5) +#define PHY_LED1_ACT (0x8<<4) +#define PHY_LED2_INT (0xe<<8) +#define PHY_SPEC_CTRL_REG 0x1c #define PHY_RGMII_CLK_STABLE (0x1<<10) -#define PHY_CLSA (0x1<<1) +#define PHY_CLSA (0x1<<1) /* Configure and enable MV88E3018 PHY */ void reset_phy(void) @@ -367,15 +371,15 @@ void reset_phy(void) return; /* RGMII clk transition on data stable */ - if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL, ®) != 0) + if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, ®)) printf("Error reading PHY spec ctrl reg\n"); - if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL, - reg | PHY_RGMII_CLK_STABLE | PHY_CLSA) != 0) + if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, + reg | PHY_RGMII_CLK_STABLE | PHY_CLSA)) printf("Error writing PHY spec ctrl reg\n"); /* leds setup */ - if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL, - PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT) != 0) + if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG, + PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT)) printf("Error writing PHY LED reg\n"); /* reset the phy */ @@ -410,7 +414,7 @@ const ulong patterns[] = { 0x00000000, 0xFF00FF00, 0x0F0F0F0F, 0xF0F0F0F0}; -const ulong NBR_OF_PATTERNS = sizeof(patterns)/sizeof(*patterns); +const ulong NBR_OF_PATTERNS = ARRAY_SIZE(patterns); const ulong OFFS_PATTERN = 3; const ulong REPEAT_PATTERN = 1000; @@ -486,7 +490,11 @@ int get_scl(void) int post_hotkeys_pressed(void) { +#if defined(CONFIG_KM_COGE5UN) + return kw_gpio_get_value(KM_POST_EN_L); +#else return !kw_gpio_get_value(KM_POST_EN_L); +#endif } ulong post_word_load(void) |
