diff options
Diffstat (limited to 'board/freescale/mx6sabresd/mx6sabresd.c')
| -rw-r--r-- | board/freescale/mx6sabresd/mx6sabresd.c | 284 |
1 files changed, 229 insertions, 55 deletions
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 3d81fffea5..ac3757f074 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -27,6 +27,9 @@ #include <i2c.h> #include <power/pmic.h> #include <power/pfuze100_pmic.h> +#include "../common/pfuze.h" +#include <asm/arch/mx6-ddr.h> + DECLARE_GLOBAL_DATA_PTR; #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ @@ -55,17 +58,16 @@ DECLARE_GLOBAL_DATA_PTR; int dram_init(void) { - gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); - + gd->ram_size = imx_ddr_size(); return 0; } -iomux_v3_cfg_t const uart1_pads[] = { +static iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; -iomux_v3_cfg_t const enet_pads[] = { +static iomux_v3_cfg_t const enet_pads[] = { MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), @@ -95,7 +97,7 @@ static void setup_iomux_enet(void) gpio_set_value(IMX_GPIO_NR(1, 25), 1); } -iomux_v3_cfg_t const usdhc2_pads[] = { +static iomux_v3_cfg_t const usdhc2_pads[] = { MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -109,7 +111,7 @@ iomux_v3_cfg_t const usdhc2_pads[] = { MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ }; -iomux_v3_cfg_t const usdhc3_pads[] = { +static iomux_v3_cfg_t const usdhc3_pads[] = { MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -123,7 +125,7 @@ iomux_v3_cfg_t const usdhc3_pads[] = { MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ }; -iomux_v3_cfg_t const usdhc4_pads[] = { +static iomux_v3_cfg_t const usdhc4_pads[] = { MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -136,7 +138,7 @@ iomux_v3_cfg_t const usdhc4_pads[] = { MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; -iomux_v3_cfg_t const ecspi1_pads[] = { +static iomux_v3_cfg_t const ecspi1_pads[] = { MX6_PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), MX6_PAD_KEY_ROW0__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), @@ -253,7 +255,8 @@ int board_mmc_getcd(struct mmc *mmc) int board_mmc_init(bd_t *bis) { - s32 status = 0; +#ifndef CONFIG_SPL_BUILD + int ret; int i; /* @@ -286,13 +289,53 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more USDHC controllers" "(%d) then supported by the board (%d)\n", i + 1, CONFIG_SYS_FSL_USDHC_NUM); - return status; + return -EINVAL; } - status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) + return ret; + } + + return 0; +#else + struct src *psrc = (struct src *)SRC_BASE_ADDR; + unsigned reg = readl(&psrc->sbmr1) >> 11; + /* + * Upon reading BOOT_CFG register the following map is done: + * Bit 11 and 12 of BOOT_CFG register can determine the current + * mmc port + * 0x1 SD1 + * 0x2 SD2 + * 0x3 SD4 + */ + + switch (reg & 0x3) { + case 0x1: + imx_iomux_v3_setup_multiple_pads( + usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); + usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR; + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); + gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; + break; + case 0x2: + imx_iomux_v3_setup_multiple_pads( + usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR; + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; + break; + case 0x3: + imx_iomux_v3_setup_multiple_pads( + usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); + usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR; + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk; + break; } - return status; + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); +#endif } #endif @@ -517,60 +560,27 @@ int board_init(void) return 0; } -static int pfuze_init(void) +int power_init_board(void) { struct pmic *p; - int ret; unsigned int reg; - ret = power_pfuze100_init(I2C_PMIC); - if (ret) - return ret; - - p = pmic_get("PFUZE100"); - ret = pmic_probe(p); - if (ret) - return ret; - - pmic_reg_read(p, PFUZE100_DEVICEID, ®); - printf("PMIC: PFUZE100 ID=0x%02x\n", reg); + p = pfuze_common_init(I2C_PMIC); + if (!p) + return -ENODEV; /* Increase VGEN3 from 2.5 to 2.8V */ pmic_reg_read(p, PFUZE100_VGEN3VOL, ®); - reg &= ~0xf; - reg |= 0xa; + reg &= ~LDO_VOL_MASK; + reg |= LDOB_2_80V; pmic_reg_write(p, PFUZE100_VGEN3VOL, reg); /* Increase VGEN5 from 2.8 to 3V */ pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); - reg &= ~0xf; - reg |= 0xc; + reg &= ~LDO_VOL_MASK; + reg |= LDOB_3_00V; pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); - /* Set SW1AB stanby volage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1ABSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg); - - /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PUZE_100_SW1ABCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PUZE_100_SW1ABCONF, reg); - - /* Set SW1C standby voltage to 0.975V */ - pmic_reg_read(p, PFUZE100_SW1CSTBY, ®); - reg &= ~0x3f; - reg |= 0x1b; - pmic_reg_write(p, PFUZE100_SW1CSTBY, reg); - - /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */ - pmic_reg_read(p, PFUZE100_SW1CCONF, ®); - reg &= ~0xc0; - reg |= 0x40; - pmic_reg_write(p, PFUZE100_SW1CCONF, reg); - return 0; } @@ -597,8 +607,6 @@ int board_late_init(void) #ifdef CONFIG_CMD_BMODE add_board_boot_modes(board_boot_modes); #endif - pfuze_init(); - return 0; } @@ -607,3 +615,169 @@ int checkboard(void) puts("Board: MX6-SabreSD\n"); return 0; } + +#ifdef CONFIG_SPL_BUILD +#include <spl.h> +#include <libfdt.h> + +const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = { + .dram_sdclk_0 = 0x00020030, + .dram_sdclk_1 = 0x00020030, + .dram_cas = 0x00020030, + .dram_ras = 0x00020030, + .dram_reset = 0x00020030, + .dram_sdcke0 = 0x00003000, + .dram_sdcke1 = 0x00003000, + .dram_sdba2 = 0x00000000, + .dram_sdodt0 = 0x00003030, + .dram_sdodt1 = 0x00003030, + .dram_sdqs0 = 0x00000030, + .dram_sdqs1 = 0x00000030, + .dram_sdqs2 = 0x00000030, + .dram_sdqs3 = 0x00000030, + .dram_sdqs4 = 0x00000030, + .dram_sdqs5 = 0x00000030, + .dram_sdqs6 = 0x00000030, + .dram_sdqs7 = 0x00000030, + .dram_dqm0 = 0x00020030, + .dram_dqm1 = 0x00020030, + .dram_dqm2 = 0x00020030, + .dram_dqm3 = 0x00020030, + .dram_dqm4 = 0x00020030, + .dram_dqm5 = 0x00020030, + .dram_dqm6 = 0x00020030, + .dram_dqm7 = 0x00020030, +}; + +const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = { + .grp_ddr_type = 0x000C0000, + .grp_ddrmode_ctl = 0x00020000, + .grp_ddrpke = 0x00000000, + .grp_addds = 0x00000030, + .grp_ctlds = 0x00000030, + .grp_ddrmode = 0x00020000, + .grp_b0ds = 0x00000030, + .grp_b1ds = 0x00000030, + .grp_b2ds = 0x00000030, + .grp_b3ds = 0x00000030, + .grp_b4ds = 0x00000030, + .grp_b5ds = 0x00000030, + .grp_b6ds = 0x00000030, + .grp_b7ds = 0x00000030, +}; + +const struct mx6_mmdc_calibration mx6_mmcd_calib = { + .p0_mpwldectrl0 = 0x001F001F, + .p0_mpwldectrl1 = 0x001F001F, + .p1_mpwldectrl0 = 0x00440044, + .p1_mpwldectrl1 = 0x00440044, + .p0_mpdgctrl0 = 0x434B0350, + .p0_mpdgctrl1 = 0x034C0359, + .p1_mpdgctrl0 = 0x434B0350, + .p1_mpdgctrl1 = 0x03650348, + .p0_mprddlctl = 0x4436383B, + .p1_mprddlctl = 0x39393341, + .p0_mpwrdlctl = 0x35373933, + .p1_mpwrdlctl = 0x48254A36, +}; + +static struct mx6_ddr3_cfg mem_ddr = { + .mem_speed = 1600, + .density = 4, + .width = 64, + .banks = 8, + .rowaddr = 14, + .coladdr = 10, + .pagesz = 2, + .trcd = 1375, + .trcmin = 4875, + .trasmin = 3500, +}; + +static void ccgr_init(void) +{ + struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + + writel(0x00C03F3F, &ccm->CCGR0); + writel(0x0030FC03, &ccm->CCGR1); + writel(0x0FFFC000, &ccm->CCGR2); + writel(0x3FF00000, &ccm->CCGR3); + writel(0x00FFF300, &ccm->CCGR4); + writel(0x0F0000C3, &ccm->CCGR5); + writel(0x000003FF, &ccm->CCGR6); +} + +static void gpr_init(void) +{ + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; + + /* enable AXI cache for VDOA/VPU/IPU */ + writel(0xF00000CF, &iomux->gpr[4]); + /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ + writel(0x007F007F, &iomux->gpr[6]); + writel(0x007F007F, &iomux->gpr[7]); +} + +/* + * This section requires the differentiation between iMX6 Sabre boards, but + * for now, it will configure only for the mx6q variant. + */ +static void spl_dram_init(void) +{ + struct mx6_ddr_sysinfo sysinfo = { + /* width of data bus:0=16,1=32,2=64 */ + .dsize = mem_ddr.width/32, + /* config for full 4GB range so that get_mem_size() works */ + .cs_density = 32, /* 32Gb per CS */ + /* single chip select */ + .ncs = 1, + .cs1_mirror = 0, + .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */ +#ifdef RTT_NOM_120OHM + .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */ +#else + .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */ +#endif + .walat = 1, /* Write additional latency */ + .ralat = 5, /* Read additional latency */ + .mif3_mode = 3, /* Command prediction working mode */ + .bi_on = 1, /* Bank interleaving enabled */ + .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ + .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ + }; + + mx6dq_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs); + mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr); +} + +void board_init_f(ulong dummy) +{ + /* setup AIPS and disable watchdog */ + arch_cpu_init(); + + ccgr_init(); + gpr_init(); + + /* iomux and setup of i2c */ + board_early_init_f(); + + /* setup GP timer */ + timer_init(); + + /* UART clocks enabled and gd valid - init serial console */ + preloader_console_init(); + + /* DDR initialization */ + spl_dram_init(); + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + /* load/boot image from boot device */ + board_init_r(NULL, 0); +} + +void reset_cpu(ulong addr) +{ +} +#endif |
