1 files changed, 0 insertions, 357 deletions
diff --git a/board/esd/pf5200/pf5200.c b/board/esd/pf5200/pf5200.c
deleted file mode 100644
index 7a9ed229ef..0000000000
--- a/board/esd/pf5200/pf5200.c
+++ /dev/null
@@ -1,357 +0,0 @@
-/*
- * (C) Copyright 2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * pf5200.c - main board support/init for the esd pf5200.
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <pci.h>
-#include <command.h>
-#include <netdev.h>
-
-#include "mt46v16m16-75.h"
-
-void init_power_switch(void);
-
-static void sdram_start(int hi_addr)
-{
-	long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
-	/* unlock mode register */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL =
-	    SDRAM_CONTROL | 0x80000000 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* precharge all banks */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL =
-	    SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* set mode register: extended mode */
-	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
-	__asm__ volatile ("sync");
-
-	/* set mode register: reset DLL */
-	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
-	__asm__ volatile ("sync");
-
-	/* precharge all banks */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL =
-	    SDRAM_CONTROL | 0x80000002 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* auto refresh */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL =
-	    SDRAM_CONTROL | 0x80000004 | hi_addr_bit;
-	__asm__ volatile ("sync");
-
-	/* set mode register */
-	*(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
-	__asm__ volatile ("sync");
-
-	/* normal operation */
-	*(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
-	__asm__ volatile ("sync");
-}
-
-/*
- * ATTENTION: Although partially referenced initdram does NOT make real use
- *            use of CONFIG_SYS_SDRAM_BASE. The code does not work if CONFIG_SYS_SDRAM_BASE
- *            is something else than 0x00000000.
- */
-
-phys_size_t initdram(int board_type)
-{
-	ulong dramsize = 0;
-	ulong test1, test2;
-
-	/* setup SDRAM chip selects */
-	*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e;	/* 2G at 0x0 */
-	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000;	/* disabled */
-	__asm__ volatile ("sync");
-
-	/* setup config registers */
-	*(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
-	*(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
-	__asm__ volatile ("sync");
-
-	/* set tap delay */
-	*(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
-	__asm__ volatile ("sync");
-
-	/* find RAM size using SDRAM CS0 only */
-	sdram_start(0);
-	test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
-	sdram_start(1);
-	test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x80000000);
-
-	if (test1 > test2) {
-		sdram_start(0);
-		dramsize = test1;
-	} else {
-		dramsize = test2;
-	}
-
-	/* memory smaller than 1MB is impossible */
-	if (dramsize < (1 << 20)) {
-		dramsize = 0;
-	}
-
-	/* set SDRAM CS0 size according to the amount of RAM found */
-	if (dramsize > 0) {
-		*(vu_long *) MPC5XXX_SDRAM_CS0CFG =
-		    0x13 + __builtin_ffs(dramsize >> 20) - 1;
-		/* let SDRAM CS1 start right after CS0 */
-		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;	/* 2G */
-	} else {
-#if 0
-		*(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0;	/* disabled */
-		/* let SDRAM CS1 start right after CS0 */
-		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;	/* 2G */
-#else
-		*(vu_long *) MPC5XXX_SDRAM_CS0CFG =
-		    0x13 + __builtin_ffs(0x08000000 >> 20) - 1;
-		/* let SDRAM CS1 start right after CS0 */
-		*(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x08000000 + 0x0000001e;	/* 2G */
-#endif
-	}
-
-#if 0
-	/* find RAM size using SDRAM CS1 only */
-	sdram_start(0);
-	get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
-	sdram_start(1);
-	get_ram_size((ulong *) (CONFIG_SYS_SDRAM_BASE + dramsize), 0x80000000);
-	sdram_start(0);
-#endif
-	/* set SDRAM CS1 size according to the amount of RAM found */
-
-	*(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize;	/* disabled */
-
-	init_power_switch();
-	return (dramsize);
-}
-
-int checkboard(void)
-{
-	puts("Board: esd ParaFinder (pf5200)\n");
-	return 0;
-}
-
-void flash_preinit(void)
-{
-	/*
-	 * Now, when we are in RAM, enable flash write
-	 * access for detection process.
-	 * Note that CS_BOOT cannot be cleared when
-	 * executing in flash.
-	 */
-	*(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1;	/* clear RO */
-}
-
-void flash_afterinit(ulong size)
-{
-	if (size == 0x02000000) {
-		/* adjust mapping */
-		*(vu_long *) MPC5XXX_BOOTCS_START =
-		    *(vu_long *) MPC5XXX_CS0_START =
-		    START_REG(CONFIG_SYS_BOOTCS_START | size);
-		*(vu_long *) MPC5XXX_BOOTCS_STOP =
-		    *(vu_long *) MPC5XXX_CS0_STOP =
-		    STOP_REG(CONFIG_SYS_BOOTCS_START | size, size);
-	}
-}
-
-#ifdef	CONFIG_PCI
-static struct pci_controller hose;
-
-extern void pci_mpc5xxx_init(struct pci_controller *);
-
-void pci_init_board(void) {
-	pci_mpc5xxx_init(&hose);
-}
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-
-void init_ide_reset(void)
-{
-	debug("init_ide_reset\n");
-
-	/* Configure PSC1_4 as GPIO output for ATA reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
-}
-
-void ide_set_reset(int idereset)
-{
-	debug("ide_reset(%d)\n", idereset);
-
-	if (idereset) {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
-	} else {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
-	}
-}
-#endif
-
-#define MPC5XXX_SIMPLEIO_GPIO_ENABLE       (MPC5XXX_GPIO + 0x0004)
-#define MPC5XXX_SIMPLEIO_GPIO_DIR          (MPC5XXX_GPIO + 0x000C)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT  (MPC5XXX_GPIO + 0x0010)
-#define MPC5XXX_SIMPLEIO_GPIO_DATA_INPUT   (MPC5XXX_GPIO + 0x0014)
-
-#define MPC5XXX_INTERRUPT_GPIO_ENABLE      (MPC5XXX_GPIO + 0x0020)
-#define MPC5XXX_INTERRUPT_GPIO_DIR         (MPC5XXX_GPIO + 0x0028)
-#define MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT (MPC5XXX_GPIO + 0x002C)
-#define MPC5XXX_INTERRUPT_GPIO_STATUS      (MPC5XXX_GPIO + 0x003C)
-
-#define GPIO_WU6	0x40000000UL
-#define GPIO_USB0       0x00010000UL
-#define GPIO_USB9       0x08000000UL
-#define GPIO_USB9S      0x00080000UL
-
-void init_power_switch(void)
-{
-	debug("init_power_switch\n");
-
-	/* Configure GPIO_WU6 as GPIO output for ATA reset */
-	*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
-	*(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WU6;
-	*(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_WU6;
-	__asm__ volatile ("sync");
-
-	*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT &= ~GPIO_USB0;
-	*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_ENABLE |= GPIO_USB0;
-	*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DIR |= GPIO_USB0;
-	__asm__ volatile ("sync");
-
-	*(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
-	*(vu_long *) MPC5XXX_INTERRUPT_GPIO_ENABLE &= ~GPIO_USB9;
-	__asm__ volatile ("sync");
-
-	if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) == 0) {
-		*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |= GPIO_USB0;
-		__asm__ volatile ("sync");
-	}
-	*(vu_char *) CONFIG_SYS_CS1_START = 0x02;	/* Red Power LED on */
-	__asm__ volatile ("sync");
-
-	*(vu_char *) (CONFIG_SYS_CS1_START + 1) = 0x02;	/* Disable driver for KB11 */
-	__asm__ volatile ("sync");
-}
-
-int board_eth_init(bd_t *bis)
-{
-	return pci_eth_init(bis);
-}
-
-void power_set_reset(int power)
-{
-	debug("ide_set_reset(%d)\n", power);
-
-	if (power) {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_WU6;
-		*(vu_long *) MPC5XXX_INTERRUPT_GPIO_DATA_OUTPUT &= ~GPIO_USB9;
-	} else {
-		*(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_WU6;
-		if ((*(vu_long *) MPC5XXX_INTERRUPT_GPIO_STATUS & GPIO_USB9S) ==
-		    0) {
-			*(vu_long *) MPC5XXX_SIMPLEIO_GPIO_DATA_OUTPUT |=
-			    GPIO_USB0;
-		}
-
-	}
-}
-
-int do_poweroff(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	power_set_reset(1);
-	return (0);
-}
-
-U_BOOT_CMD(poweroff, 1, 1, do_poweroff, "Switch off power", "");
-
-int phypower(int flag)
-{
-	u32 addr;
-	vu_long *reg;
-	int status;
-	pci_dev_t dev;
-
-	dev = PCI_BDF(0, 0x18, 0);
-	status = pci_read_config_dword(dev, PCI_BASE_ADDRESS_1, &addr);
-	if (status == 0) {
-		reg = (vu_long *) (addr + 0x00000040);
-		*reg |= 0x40000000;
-		__asm__ volatile ("sync");
-
-		reg = (vu_long *) (addr + 0x001000c);
-		*reg |= 0x20000000;
-		__asm__ volatile ("sync");
-
-		reg = (vu_long *) (addr + 0x0010004);
-		if (flag != 0) {
-			*reg &= ~0x20000000;
-		} else {
-			*reg |= 0x20000000;
-		}
-		__asm__ volatile ("sync");
-	}
-	return (status);
-}
-
-int do_phypower(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	if (argv[1][0] == '0')
-		(void)phypower(0);
-	else
-		(void)phypower(1);
-
-	return (0);
-}
-
-U_BOOT_CMD(phypower, 2, 2, do_phypower,
-	   "Switch power of ethernet phy", "");
-
-int do_writepci(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	unsigned int addr;
-	unsigned int size;
-	int i;
-	volatile unsigned long *ptr;
-
-	addr = simple_strtol(argv[1], NULL, 16);
-	size = simple_strtol(argv[2], NULL, 16);
-
-	printf("\nWriting at addr %08x, size %08x.\n", addr, size);
-
-	while (1) {
-		ptr = (volatile unsigned long *)addr;
-		for (i = 0; i < (size >> 2); i++) {
-			*ptr++ = i;
-		}
-
-		/* Abort if ctrl-c was pressed */
-		if (ctrlc()) {
-			puts("\nAbort\n");
-			return 0;
-		}
-		putc('.');
-	}
-	return 0;
-}
-
-U_BOOT_CMD(writepci, 3, 1, do_writepci,
-	"Write some data to pcibus",
-	"<addr> <size>\n"
-	""
-);